deleted file mode 100644
@@ -1,212 +0,0 @@
-* Rockchip rk3399 DMC (Dynamic Memory Controller) device
-
-Required properties:
-- compatible: Must be "rockchip,rk3399-dmc".
-- devfreq-events: Node to get DDR loading, Refer to
- Documentation/devicetree/bindings/devfreq/event/
- rockchip-dfi.txt
-- clocks: Phandles for clock specified in "clock-names" property
-- clock-names : The name of clock used by the DFI, must be
- "pclk_ddr_mon";
-- operating-points-v2: Refer to Documentation/devicetree/bindings/opp/opp-v2.yaml
- for details.
-- center-supply: DMC supply node.
-- status: Marks the node enabled/disabled.
-- rockchip,pmu: Phandle to the syscon managing the "PMU general register
- files".
-
-Optional properties:
-- interrupts: The CPU interrupt number. The interrupt specifier
- format depends on the interrupt controller.
- It should be a DCF interrupt. When DDR DVFS finishes
- a DCF interrupt is triggered.
-- rockchip,pmu: Phandle to the syscon managing the "PMU general register
- files".
-
-Following properties relate to DDR timing:
-
-- rockchip,dram_speed_bin : Value reference include/dt-bindings/clock/rk3399-ddr.h,
- it selects the DDR3 cl-trp-trcd type. It must be
- set according to "Speed Bin" in DDR3 datasheet,
- DO NOT use a smaller "Speed Bin" than specified
- for the DDR3 being used.
-
-- rockchip,pd_idle : Configure the PD_IDLE value. Defines the
- power-down idle period in which memories are
- placed into power-down mode if bus is idle
- for PD_IDLE DFI clock cycles.
-
-- rockchip,sr_idle : Configure the SR_IDLE value. Defines the
- self-refresh idle period in which memories are
- placed into self-refresh mode if bus is idle
- for SR_IDLE * 1024 DFI clock cycles (DFI
- clocks freq is half of DRAM clock), default
- value is "0".
-
-- rockchip,sr_mc_gate_idle : Defines the memory self-refresh and controller
- clock gating idle period. Memories are placed
- into self-refresh mode and memory controller
- clock arg gating started if bus is idle for
- sr_mc_gate_idle*1024 DFI clock cycles.
-
-- rockchip,srpd_lite_idle : Defines the self-refresh power down idle
- period in which memories are placed into
- self-refresh power down mode if bus is idle
- for srpd_lite_idle * 1024 DFI clock cycles.
- This parameter is for LPDDR4 only.
-
-- rockchip,standby_idle : Defines the standby idle period in which
- memories are placed into self-refresh mode.
- The controller, pi, PHY and DRAM clock will
- be gated if bus is idle for standby_idle * DFI
- clock cycles.
-
-- rockchip,dram_dll_dis_freq : Defines the DDR3 DLL bypass frequency in MHz.
- When DDR frequency is less than DRAM_DLL_DISB_FREQ,
- DDR3 DLL will be bypassed. Note: if DLL was bypassed,
- the odt will also stop working.
-
-- rockchip,phy_dll_dis_freq : Defines the PHY dll bypass frequency in
- MHz (Mega Hz). When DDR frequency is less than
- DRAM_DLL_DISB_FREQ, PHY DLL will be bypassed.
- Note: PHY DLL and PHY ODT are independent.
-
-- rockchip,ddr3_odt_dis_freq : When the DRAM type is DDR3, this parameter defines
- the ODT disable frequency in MHz (Mega Hz).
- when the DDR frequency is less then ddr3_odt_dis_freq,
- the ODT on the DRAM side and controller side are
- both disabled.
-
-- rockchip,ddr3_drv : When the DRAM type is DDR3, this parameter defines
- the DRAM side driver strength in ohms. Default
- value is 40.
-
-- rockchip,ddr3_odt : When the DRAM type is DDR3, this parameter defines
- the DRAM side ODT strength in ohms. Default value
- is 120.
-
-- rockchip,phy_ddr3_ca_drv : When the DRAM type is DDR3, this parameter defines
- the phy side CA line (incluing command line,
- address line and clock line) driver strength.
- Default value is 40.
-
-- rockchip,phy_ddr3_dq_drv : When the DRAM type is DDR3, this parameter defines
- the PHY side DQ line (including DQS/DQ/DM line)
- driver strength. Default value is 40.
-
-- rockchip,phy_ddr3_odt : When the DRAM type is DDR3, this parameter defines
- the PHY side ODT strength. Default value is 240.
-
-- rockchip,lpddr3_odt_dis_freq : When the DRAM type is LPDDR3, this parameter defines
- then ODT disable frequency in MHz (Mega Hz).
- When DDR frequency is less then ddr3_odt_dis_freq,
- the ODT on the DRAM side and controller side are
- both disabled.
-
-- rockchip,lpddr3_drv : When the DRAM type is LPDDR3, this parameter defines
- the DRAM side driver strength in ohms. Default
- value is 34.
-
-- rockchip,lpddr3_odt : When the DRAM type is LPDDR3, this parameter defines
- the DRAM side ODT strength in ohms. Default value
- is 240.
-
-- rockchip,phy_lpddr3_ca_drv : When the DRAM type is LPDDR3, this parameter defines
- the PHY side CA line (including command line,
- address line and clock line) driver strength.
- Default value is 40.
-
-- rockchip,phy_lpddr3_dq_drv : When the DRAM type is LPDDR3, this parameter defines
- the PHY side DQ line (including DQS/DQ/DM line)
- driver strength. Default value is 40.
-
-- rockchip,phy_lpddr3_odt : When dram type is LPDDR3, this parameter define
- the phy side odt strength, default value is 240.
-
-- rockchip,lpddr4_odt_dis_freq : When the DRAM type is LPDDR4, this parameter
- defines the ODT disable frequency in
- MHz (Mega Hz). When the DDR frequency is less then
- ddr3_odt_dis_freq, the ODT on the DRAM side and
- controller side are both disabled.
-
-- rockchip,lpddr4_drv : When the DRAM type is LPDDR4, this parameter defines
- the DRAM side driver strength in ohms. Default
- value is 60.
-
-- rockchip,lpddr4_dq_odt : When the DRAM type is LPDDR4, this parameter defines
- the DRAM side ODT on DQS/DQ line strength in ohms.
- Default value is 40.
-
-- rockchip,lpddr4_ca_odt : When the DRAM type is LPDDR4, this parameter defines
- the DRAM side ODT on CA line strength in ohms.
- Default value is 40.
-
-- rockchip,phy_lpddr4_ca_drv : When the DRAM type is LPDDR4, this parameter defines
- the PHY side CA line (including command address
- line) driver strength. Default value is 40.
-
-- rockchip,phy_lpddr4_ck_cs_drv : When the DRAM type is LPDDR4, this parameter defines
- the PHY side clock line and CS line driver
- strength. Default value is 80.
-
-- rockchip,phy_lpddr4_dq_drv : When the DRAM type is LPDDR4, this parameter defines
- the PHY side DQ line (including DQS/DQ/DM line)
- driver strength. Default value is 80.
-
-- rockchip,phy_lpddr4_odt : When the DRAM type is LPDDR4, this parameter defines
- the PHY side ODT strength. Default value is 60.
-
-Example:
- dmc_opp_table: dmc_opp_table {
- compatible = "operating-points-v2";
-
- opp00 {
- opp-hz = /bits/ 64 <300000000>;
- opp-microvolt = <900000>;
- };
- opp01 {
- opp-hz = /bits/ 64 <666000000>;
- opp-microvolt = <900000>;
- };
- };
-
- dmc: dmc {
- compatible = "rockchip,rk3399-dmc";
- devfreq-events = <&dfi>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&cru SCLK_DDRC>;
- clock-names = "dmc_clk";
- operating-points-v2 = <&dmc_opp_table>;
- center-supply = <&ppvar_centerlogic>;
- upthreshold = <15>;
- downdifferential = <10>;
- rockchip,ddr3_speed_bin = <21>;
- rockchip,pd_idle = <0x40>;
- rockchip,sr_idle = <0x2>;
- rockchip,sr_mc_gate_idle = <0x3>;
- rockchip,srpd_lite_idle = <0x4>;
- rockchip,standby_idle = <0x2000>;
- rockchip,dram_dll_dis_freq = <300>;
- rockchip,phy_dll_dis_freq = <125>;
- rockchip,auto_pd_dis_freq = <666>;
- rockchip,ddr3_odt_dis_freq = <333>;
- rockchip,ddr3_drv = <40>;
- rockchip,ddr3_odt = <120>;
- rockchip,phy_ddr3_ca_drv = <40>;
- rockchip,phy_ddr3_dq_drv = <40>;
- rockchip,phy_ddr3_odt = <240>;
- rockchip,lpddr3_odt_dis_freq = <333>;
- rockchip,lpddr3_drv = <34>;
- rockchip,lpddr3_odt = <240>;
- rockchip,phy_lpddr3_ca_drv = <40>;
- rockchip,phy_lpddr3_dq_drv = <40>;
- rockchip,phy_lpddr3_odt = <240>;
- rockchip,lpddr4_odt_dis_freq = <333>;
- rockchip,lpddr4_drv = <60>;
- rockchip,lpddr4_dq_odt = <40>;
- rockchip,lpddr4_ca_odt = <40>;
- rockchip,phy_lpddr4_ca_drv = <40>;
- rockchip,phy_lpddr4_ck_cs_drv = <80>;
- rockchip,phy_lpddr4_dq_drv = <80>;
- rockchip,phy_lpddr4_odt = <60>;
- };
new file mode 100644
@@ -0,0 +1,306 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# %YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/rockchip,rk3399-dmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip rk3399 DMC (Dynamic Memory Controller) device
+
+maintainers:
+ - Brian Norris <briannorris@chromium.org>
+
+properties:
+ compatible:
+ enum:
+ - rockchip,rk3399-dmc
+
+ devfreq-events:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ Node to get DDR loading. Refer to
+ Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt.
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: dmc_clk
+
+ operating-points-v2: true
+
+ center-supply:
+ description:
+ DMC regulator supply.
+
+ rockchip,pmu:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ Phandle to the syscon managing the "PMU general register files".
+
+ interrupts:
+ maxItems: 1
+ description:
+ The CPU interrupt number. It should be a DCF interrupt. When DDR DVFS
+ finishes, a DCF interrupt is triggered.
+
+ rockchip,ddr3_speed_bin:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ For values, reference include/dt-bindings/clock/rk3399-ddr.h. Selects the
+ DDR3 cl-trp-trcd type. It must be set according to "Speed Bin" in DDR3
+ datasheet; DO NOT use a smaller "Speed Bin" than specified for the DDR3
+ being used.
+
+ rockchip,pd_idle:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Configure the PD_IDLE value. Defines the power-down idle period in which
+ memories are placed into power-down mode if bus is idle for PD_IDLE DFI
+ clock cycles.
+
+ rockchip,sr_idle:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Configure the SR_IDLE value. Defines the self-refresh idle period in
+ which memories are placed into self-refresh mode if bus is idle for
+ SR_IDLE * 1024 DFI clock cycles (DFI clocks freq is half of DRAM clock).
+ default: 0
+
+ rockchip,sr_mc_gate_idle:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Defines the memory self-refresh and controller clock gating idle period.
+ Memories are placed into self-refresh mode and memory controller clock
+ arg gating started if bus is idle for sr_mc_gate_idle*1024 DFI clock
+ cycles.
+
+ rockchip,srpd_lite_idle:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Defines the self-refresh power down idle period in which memories are
+ placed into self-refresh power down mode if bus is idle for
+ srpd_lite_idle * 1024 DFI clock cycles. This parameter is for LPDDR4
+ only.
+
+ rockchip,standby_idle:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Defines the standby idle period in which memories are placed into
+ self-refresh mode. The controller, pi, PHY and DRAM clock will be gated
+ if bus is idle for standby_idle * DFI clock cycles.
+
+ rockchip,dram_dll_dis_freq:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Defines the DDR3 DLL bypass frequency in MHz. When DDR frequency is less
+ than DRAM_DLL_DISB_FREQ, DDR3 DLL will be bypassed.
+ Note: if DLL was bypassed, the odt will also stop working.
+
+ rockchip,phy_dll_dis_freq:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Defines the PHY dll bypass frequency in MHz (Mega Hz). When DDR frequency
+ is less than DRAM_DLL_DISB_FREQ, PHY DLL will be bypassed.
+ Note: PHY DLL and PHY ODT are independent.
+
+ rockchip,auto_pd_dis_freq:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Defines the auto PD disable frequency in MHz.
+
+ rockchip,ddr3_odt_dis_freq:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is DDR3, this parameter defines the ODT disable
+ frequency in MHz (Mega Hz). When the DDR frequency is less then
+ ddr3_odt_dis_freq, the ODT on the DRAM side and controller side are both
+ disabled.
+
+ rockchip,ddr3_drv:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is DDR3, this parameter defines the DRAM side drive
+ strength in ohms.
+ default: 40
+
+ rockchip,ddr3_odt:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is DDR3, this parameter defines the DRAM side ODT
+ strength in ohms.
+ default: 120
+
+ rockchip,phy_ddr3_ca_drv:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is DDR3, this parameter defines the phy side CA line
+ (incluing command line, address line and clock line) drive strength.
+ default: 40
+
+ rockchip,phy_ddr3_dq_drv:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is DDR3, this parameter defines the PHY side DQ line
+ (including DQS/DQ/DM line) drive strength.
+ default: 40
+
+ rockchip,phy_ddr3_odt:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is DDR3, this parameter defines the PHY side ODT
+ strength.
+ default: 240
+
+ rockchip,lpddr3_odt_dis_freq:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR3, this parameter defines then ODT disable
+ frequency in MHz (Mega Hz). When DDR frequency is less then
+ ddr3_odt_dis_freq, the ODT on the DRAM side and controller side are both
+ disabled.
+
+ rockchip,lpddr3_drv:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR3, this parameter defines the DRAM side drive
+ strength in ohms.
+ default: 34
+
+ rockchip,lpddr3_odt:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR3, this parameter defines the DRAM side ODT
+ strength in ohms.
+ default: 240
+
+ rockchip,phy_lpddr3_ca_drv:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR3, this parameter defines the PHY side CA line
+ (including command line, address line and clock line) drive strength.
+ default: 40
+
+ rockchip,phy_lpddr3_dq_drv:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR3, this parameter defines the PHY side DQ line
+ (including DQS/DQ/DM line) drive strength.
+ default: 40
+
+ rockchip,phy_lpddr3_odt:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When dram type is LPDDR3, this parameter define the phy side odt
+ strength, default value is 240.
+
+ rockchip,lpddr4_odt_dis_freq:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR4, this parameter defines the ODT disable
+ frequency in MHz (Mega Hz). When the DDR frequency is less then
+ ddr3_odt_dis_freq, the ODT on the DRAM side and controller side are both
+ disabled.
+
+ rockchip,lpddr4_drv:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR4, this parameter defines the DRAM side drive
+ strength in ohms.
+ default: 60
+
+ rockchip,lpddr4_dq_odt:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR4, this parameter defines the DRAM side ODT on
+ DQS/DQ line strength in ohms.
+ default: 40
+
+ rockchip,lpddr4_ca_odt:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR4, this parameter defines the DRAM side ODT on
+ CA line strength in ohms.
+ default: 40
+
+ rockchip,phy_lpddr4_ca_drv:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR4, this parameter defines the PHY side CA line
+ (including command address line) drive strength.
+ default: 40
+
+ rockchip,phy_lpddr4_ck_cs_drv:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR4, this parameter defines the PHY side clock
+ line and CS line drive strength.
+ default: 80
+
+ rockchip,phy_lpddr4_dq_drv:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR4, this parameter defines the PHY side DQ line
+ (including DQS/DQ/DM line) drive strength.
+ default: 80
+
+ rockchip,phy_lpddr4_odt:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ When the DRAM type is LPDDR4, this parameter defines the PHY side ODT
+ strength.
+ default: 60
+
+required:
+ - compatible
+ - devfreq-events
+ - clocks
+ - clock-names
+ - operating-points-v2
+ - center-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/rk3399-cru.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ memory-controller {
+ compatible = "rockchip,rk3399-dmc";
+ devfreq-events = <&dfi>;
+ rockchip,pmu = <&pmu>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru SCLK_DDRC>;
+ clock-names = "dmc_clk";
+ operating-points-v2 = <&dmc_opp_table>;
+ center-supply = <&ppvar_centerlogic>;
+ rockchip,ddr3_speed_bin = <21>;
+ rockchip,pd_idle = <0x40>;
+ rockchip,sr_idle = <0x2>;
+ rockchip,sr_mc_gate_idle = <0x3>;
+ rockchip,srpd_lite_idle = <0x4>;
+ rockchip,standby_idle = <0x2000>;
+ rockchip,dram_dll_dis_freq = <300>;
+ rockchip,phy_dll_dis_freq = <125>;
+ rockchip,auto_pd_dis_freq = <666>;
+ rockchip,ddr3_odt_dis_freq = <333>;
+ rockchip,ddr3_drv = <40>;
+ rockchip,ddr3_odt = <120>;
+ rockchip,phy_ddr3_ca_drv = <40>;
+ rockchip,phy_ddr3_dq_drv = <40>;
+ rockchip,phy_ddr3_odt = <240>;
+ rockchip,lpddr3_odt_dis_freq = <333>;
+ rockchip,lpddr3_drv = <34>;
+ rockchip,lpddr3_odt = <240>;
+ rockchip,phy_lpddr3_ca_drv = <40>;
+ rockchip,phy_lpddr3_dq_drv = <40>;
+ rockchip,phy_lpddr3_odt = <240>;
+ rockchip,lpddr4_odt_dis_freq = <333>;
+ rockchip,lpddr4_drv = <60>;
+ rockchip,lpddr4_dq_odt = <40>;
+ rockchip,lpddr4_ca_odt = <40>;
+ rockchip,phy_lpddr4_ca_drv = <40>;
+ rockchip,phy_lpddr4_ck_cs_drv = <80>;
+ rockchip,phy_lpddr4_dq_drv = <80>;
+ rockchip,phy_lpddr4_odt = <60>;
+ };
I want to add, deprecate, and bugfix some properties, as well as add the first users. This is easier with a proper schema. The transformation is mostly straightforward, plus a few notable tweaks: * Renamed rockchip,dram_speed_bin to rockchip,ddr3_speed_bin. The driver code and the example matched, but the description was different. I went with the implementation. Note that this property is also slated for deprecation/deletion in the subsequent patches. * Drop upthreshold and downdifferential properties from the example. These were undocumented (so, wouldn't pass validation), but were representing software properties (governor tweaks). I drop them from the driver in subsequent patches. * Rename clock from pclk_ddr_mon to dmc_clk. The driver, DT example, and all downstream users matched -- the binding definition was the exception. Anyway, "dmc_clk" is a more appropriately generic name. * Choose a better filename and location (this is a memory controller). Signed-off-by: Brian Norris <briannorris@chromium.org> --- Changes in v4: * Update .yaml to use more "default" entries, instead of free-form text * s/phandle-array/phandle/ * Move to .../memory-controllers, update filename Changes in v3: * Add |maxItems| for devfreq-events * Improve deprecation notes Changes in v2: * rename to 'memory-controller' in example * place 'required' after properties * drop superluous free-form references and repetitions of other bindings * fix for yamllint .../bindings/devfreq/rk3399_dmc.txt | 212 ------------ .../rockchip,rk3399-dmc.yaml | 306 ++++++++++++++++++ 2 files changed, 306 insertions(+), 212 deletions(-) delete mode 100644 Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt create mode 100644 Documentation/devicetree/bindings/memory-controllers/rockchip,rk3399-dmc.yaml