| Message ID | BY5PR02MB70092607CD7CDD8CF8BCD464D9E09@BY5PR02MB7009.namprd02.prod.outlook.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | drm/panel: nt36672a: add backlight support | expand |
On 2022-04-01 05:48:10, Joel Selvaraj wrote: > Xiaomi Poco F1 uses the QCOM WLED driver for backlight control. > Enable and link it to the panel to use it. > > Signed-off-by: Joel Selvaraj <jo@jsfamily.in> Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> > --- > Changes in v2: > - Remove qcom,enabled-strings property as either it or qcom,num-strings > should be present. qcom,num-strings is specified and sufficient. > (Marijn Suijten's Suggestion) Thanks :) > arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 12 ++++++++++++ > 1 file changed, 12 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts > index 798fc72578a7..d88dc07205f7 100644 > --- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts > +++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts > @@ -231,6 +231,7 @@ panel@0 { > #address-cells = <1>; > #size-cells = <0>; > > + backlight = <&pmi8998_wled>; > reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; > > port { > @@ -314,6 +315,17 @@ vol_up_pin_a: vol-up-active { > }; > }; > > +&pmi8998_wled { > + status = "okay"; > + qcom,current-boost-limit = <970>; > + qcom,ovp-millivolt = <29600>; > + qcom,current-limit-microamp = <20000>; > + qcom,num-strings = <2>; > + qcom,switching-freq = <600>; > + qcom,external-pfet; > + qcom,cabc; Unlike the number of connected strings and configured ovp/current limits, aren't external-pfet (and probably switching-freq, perhaps CABC) hardware features that are common across all users of `pmi8998`? - Marijn > +}; > + > &pm8998_pon { > resin { > compatible = "qcom,pm8941-resin"; > -- > 2.35.1 >
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts index 798fc72578a7..d88dc07205f7 100644 --- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts +++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts @@ -231,6 +231,7 @@ panel@0 { #address-cells = <1>; #size-cells = <0>; + backlight = <&pmi8998_wled>; reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; port { @@ -314,6 +315,17 @@ vol_up_pin_a: vol-up-active { }; }; +&pmi8998_wled { + status = "okay"; + qcom,current-boost-limit = <970>; + qcom,ovp-millivolt = <29600>; + qcom,current-limit-microamp = <20000>; + qcom,num-strings = <2>; + qcom,switching-freq = <600>; + qcom,external-pfet; + qcom,cabc; +}; + &pm8998_pon { resin { compatible = "qcom,pm8941-resin";
Xiaomi Poco F1 uses the QCOM WLED driver for backlight control. Enable and link it to the panel to use it. Signed-off-by: Joel Selvaraj <jo@jsfamily.in> --- Changes in v2: - Remove qcom,enabled-strings property as either it or qcom,num-strings should be present. qcom,num-strings is specified and sufficient. (Marijn Suijten's Suggestion) arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+)