@@ -83,7 +83,6 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-pompom-r3.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-pompom-r3-lte.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-r1-lte.dtb
-dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-herobrine-r0.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-herobrine-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp2.dtb
deleted file mode 100644
@@ -1,1352 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Google Herobrine board device tree source
- *
- * Copyright 2021 Google LLC.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
-#include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
-#include <dt-bindings/input/gpio-keys.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
-
-#include "sc7280.dtsi"
-
-/* PMICs depend on spmi_bus label and so must come after SoC */
-#include "pm7325.dtsi"
-#include "pm8350c.dtsi"
-#include "pmk8350.dtsi"
-
-#include "sc7280-chrome-common.dtsi"
-
-/ {
- model = "Google Herobrine (rev0)";
- compatible = "google,herobrine-rev0", "qcom,sc7280";
-};
-
-/ {
- aliases {
- serial0 = &uart5;
- serial1 = &uart7;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- /* FIXED REGULATORS - parents above children */
-
- /* This is the top level supply and variable voltage */
- ppvar_sys: ppvar-sys-regulator {
- compatible = "regulator-fixed";
- regulator-name = "ppvar_sys";
- regulator-always-on;
- regulator-boot-on;
- };
-
- /* This divides ppvar_sys by 2, so voltage is variable */
- src_vph_pwr: src-vph-pwr-regulator {
- compatible = "regulator-fixed";
- regulator-name = "src_vph_pwr";
-
- /* EC turns on with switchcap_on; always on for AP */
- regulator-always-on;
- regulator-boot-on;
-
- vin-supply = <&ppvar_sys>;
- };
-
- pp5000_s3: pp5000-s3-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp5000_s3";
-
- /* EC turns on with en_pp5000_s3; always on for AP */
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
-
- vin-supply = <&ppvar_sys>;
- };
-
- pp3300_z1: pp3300-z1-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp3300_z1";
-
- /* EC turns on with en_pp3300_z1; always on for AP */
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- vin-supply = <&ppvar_sys>;
- };
-
- pp3300_audio:
- pp3300_codec: pp3300-codec-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp3300_codec";
-
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&en_pp3300_codec>;
-
- vin-supply = <&pp3300_z1>;
- };
-
- pp3300_cam:
- pp3300_edp:
- pp3300_ts: pp3300-edp-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp3300_edp";
-
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&tlmm 80 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&en_pp3300_dx_edp>;
-
- vin-supply = <&pp3300_z1>;
- };
-
- pp3300_fp:
- pp3300_fp_ls:
- pp3300_mcu: pp3300-fp-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp3300_fp";
-
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- regulator-boot-on;
- regulator-always-on;
-
- /*
- * WARNING: it is intentional that GPIO 42 isn't listed here.
- * The userspace script for updating the fingerprint firmware
- * needs to control the FP regulators during a FW update,
- * hence the signal can't be owned by the kernel regulator.
- */
-
- pinctrl-names = "default";
- pinctrl-0 = <&en_fp_rails>;
-
- vin-supply = <&pp3300_z1>;
- };
-
- pp3300_hub: pp3300-hub-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp3300_hub";
-
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- regulator-boot-on;
- regulator-always-on;
-
- gpio = <&tlmm 24 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&en_pp3300_hub>;
-
- vin-supply = <&pp3300_z1>;
- };
-
- pp3300_tp: pp3300-tp-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp3300_tp";
-
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- /* AP turns on with PP1800_L18B_S0; always on for AP */
- regulator-always-on;
- regulator-boot-on;
-
- vin-supply = <&pp3300_z1>;
- };
-
- pp2850_uf_cam: pp2850-uf-cam-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp2850_uf_cam";
-
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
-
- gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&uf_cam_en>;
-
- vin-supply = <&pp3300_cam>;
- };
-
- pp2850_vcm_wf_cam: pp2850-vcm-wf-cam-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp2850_vcm_wf_cam";
-
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
-
- gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&wf_cam_en>;
-
- vin-supply = <&pp3300_cam>;
- };
-
- pp2850_wf_cam: pp2850-wf-cam-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp2850_wf_cam";
-
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
-
- gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- /*
- * The pinconf can only be referenced once so we put it on the
- * first regulator and comment it out here.
- *
- * pinctrl-names = "default";
- * pinctrl-0 = <&wf_cam_en>;
- */
-
- vin-supply = <&pp3300_cam>;
- };
-
- pp1800_fp: pp1800-fp-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp1800_fp";
-
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- regulator-always-on;
-
- /*
- * WARNING: it is intentional that GPIO 42 isn't listed here.
- * The userspace script for updating the fingerprint firmware
- * needs to control the FP regulators during a FW update,
- * hence the signal can't be owned by the kernel regulator.
- */
-
- pinctrl-names = "default";
- pinctrl-0 = <&en_fp_rails>;
-
- vin-supply = <&pp1800_l18b_s0>;
- status = "disabled";
- };
-
- pp1800_uf_cam: pp1800-uf-cam-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp1800_uf_cam";
-
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- /*
- * The pinconf can only be referenced once so we put it on the
- * first regulator and comment it out here.
- *
- * pinctrl-names = "default";
- * pinctrl-0 = <&uf_cam_en>;
- */
-
- vin-supply = <&pp1800_l19b>;
- };
-
- pp1800_wf_cam: pp1800-wf-cam-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp1800_wf_cam";
-
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- /*
- * The pinconf can only be referenced once so we put it on the
- * first regulator and comment it out here.
- *
- * pinctrl-names = "default";
- * pinctrl-0 = <&wf_cam_en>;
- */
-
- vin-supply = <&pp1800_l19b>;
- };
-
- pp1200_wf_cam: pp1200-wf-cam-regulator {
- compatible = "regulator-fixed";
- regulator-name = "pp1200_wf_cam";
-
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
-
- gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- /*
- * The pinconf can only be referenced once so we put it on the
- * first regulator and comment it out here.
- *
- * pinctrl-names = "default";
- * pinctrl-0 = <&wf_cam_en>;
- */
-
- vin-supply = <&pp1200_l6b>;
- };
-
- /* BOARD-SPECIFIC TOP LEVEL NODES */
-
- gpio_keys: gpio-keys {
- compatible = "gpio-keys";
- status = "disabled";
- pinctrl-names = "default";
- pinctrl-0 = <&pen_pdct_l>;
-
- pen_insert: pen-insert {
- label = "Pen Insert";
-
- /* Insert = low, eject = high */
- gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
- linux,code = <SW_PEN_INSERTED>;
- linux,input-type = <EV_SW>;
- wakeup-event-action = <EV_ACT_DEASSERTED>;
- wakeup-source;
- };
- };
-
- pwmleds {
- compatible = "pwm-leds";
- status = "disabled";
- keyboard_backlight: keyboard-backlight {
- status = "disabled";
- label = "cros_ec::kbd_backlight";
- pwms = <&cros_ec_pwm 0>;
- max-brightness = <1023>;
- };
- };
-};
-
-&apps_rsc {
- pm7325-regulators {
- compatible = "qcom,pm7325-rpmh-regulators";
- qcom,pmic-id = "b";
-
- vdd19_pmu_pcie_i:
- vdd19_pmu_rfa_i:
- vreg_s1b_wlan:
- vreg_s1b: smps1 {
- regulator-min-microvolt = <1856000>;
- regulator-max-microvolt = <2040000>;
- };
-
- vdd_pmu_aon_i:
- vreg_s7b_wlan:
- vreg_s7b: smps7 {
- regulator-min-microvolt = <535000>;
- regulator-max-microvolt = <1120000>;
- };
-
- vdd13_pmu_pcie_i:
- vdd13_pmu_rfa_i:
- vreg_s8b_wlan:
- vreg_s8b: smps8 {
- regulator-min-microvolt = <1256000>;
- regulator-max-microvolt = <1500000>;
- };
-
- vdda_usb_ss_dp_core:
- vreg_l1b: ldo1 {
- regulator-min-microvolt = <825000>;
- regulator-max-microvolt = <925000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vdda_usb_hs0_3p1:
- vreg_l2b: ldo2 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <3544000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- pp1200_l6b:
- vdd_ufs_1p2:
- vdd_vref:
- vdda_csi01_1p2:
- vdda_csi23_1p2:
- vdda_csi4_1p2:
- vdda_dsi0_1p2:
- vdda_pcie0_1p2:
- vdda_pcie1_1p2:
- vdda_usb_ss_dp_1p2:
- vdda_qlink0_1p2_ck:
- vdda_qlink1_1p2_ck:
- vreg_l6b_1p2:
- vreg_l6b: ldo6 {
- regulator-min-microvolt = <1120000>;
- regulator-max-microvolt = <1408000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- pp2950_l7b:
- vreg_l7b: ldo7 {
- regulator-min-microvolt = <2960000>;
- regulator-max-microvolt = <2960000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- codec_vcc:
- pp1800_l18b_s0:
- pp1800_ts:
- vdd1:
- vddpx_0:
- vddpx_3:
- vddpx_7:
- vreg_l18b: ldo18 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2000000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- pp1800_l19b:
- vddpx_ts:
- vddpx_wl4otp:
- vreg_l19b: ldo19 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
- };
-
- pm8350c-regulators {
- compatible = "qcom,pm8350c-rpmh-regulators";
- qcom,pmic-id = "c";
-
- vreg_s1c: smps1 {
- regulator-min-microvolt = <2190000>;
- regulator-max-microvolt = <2210000>;
- };
-
- vddpx_1:
- vreg_s9c: smps9 {
- regulator-min-microvolt = <1010000>;
- regulator-max-microvolt = <1170000>;
- };
-
- pp1800_l1c:
- pp1800_pen:
- vdd_a_gfx_cs_1p1:
- vdd_a_cxo_1p8:
- vdd_qfprom:
- vdda_apc_cs_1p8:
- vdda_qrefs_1p8:
- vdda_turing_q6_cs_1p8:
- vdda_usb_hs0_1p8:
- vreg_l1c: ldo1 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1980000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- dmic_vdd:
- pp1800_alc5682:
- pp1800_l2c:
- pp1800_vreg_alc5682:
- vreg_l2c: ldo2 {
- regulator-min-microvolt = <1620000>;
- regulator-max-microvolt = <1980000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- pp3300_sar:
- pp3300_sensor:
- vreg_l3c: ldo3 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <3540000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- ppvar_uim1:
- vddpx_5:
- vreg_l4c: ldo4 {
- regulator-min-microvolt = <1620000>;
- regulator-max-microvolt = <3300000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- pp2950_l5c:
- uim_vcc:
- vddpx_6:
- vreg_l5c: ldo5 {
- regulator-min-microvolt = <1620000>;
- regulator-max-microvolt = <3300000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- ppvar_l6c:
- vddpx_2:
- vreg_l6c: ldo6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l7c: ldo7 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3544000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- pp1800_prox:
- pp1800_sar:
- vreg_l8c: ldo8 {
- regulator-min-microvolt = <1620000>;
- regulator-max-microvolt = <2000000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- pp2950_l9c:
- vreg_l9c: ldo9 {
- regulator-min-microvolt = <2960000>;
- regulator-max-microvolt = <2960000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vdd_a_gnss_0p9:
- vdd_ufs_core:
- vdd_usb_hs0_core:
- vdd_vref_0p9:
- vdda_csi01_0p9:
- vdda_csi23_0p9:
- vdda_csi4_0p9:
- vdda_dsi0_pll_0p9:
- vdda_dsi0_0p9:
- vdda_pcie0_core:
- vdda_pcie1_core:
- vdda_qlink0_0p9:
- vdda_qlink1_0p9:
- vdda_qlink0_0p9_ck:
- vdda_qlink1_0p9_ck:
- vdda_qrefs_0p875:
- vreg_l10c_0p8:
- vreg_l10c: ldo10 {
- regulator-min-microvolt = <720000>;
- regulator-max-microvolt = <1050000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- pp2800_l11c:
- vreg_l11c: ldo11 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <3544000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- pp1800_l12c:
- vreg_l12c: ldo12 {
- regulator-min-microvolt = <1650000>;
- regulator-max-microvolt = <2000000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- pp3300_l13c:
- vreg_l13c: ldo13 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <3544000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_bob: bob {
- regulator-min-microvolt = <3008000>;
- regulator-max-microvolt = <3960000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
- };
- };
-};
-
-ap_tp_i2c: &i2c1 {
- status = "okay";
- clock-frequency = <400000>;
-
- trackpad: trackpad@15 {
- compatible = "elan,ekth3000";
- reg = <0x15>;
- pinctrl-names = "default";
- pinctrl-0 = <&tp_int_odl>;
-
- interrupt-parent = <&tlmm>;
- interrupts = <102 IRQ_TYPE_EDGE_FALLING>;
-
- vcc-supply = <&pp3300_z1>;
-
- wakeup-source;
- };
-};
-
-ap_h1_i2c: &i2c12 {
- status = "okay";
- clock-frequency = <400000>;
-
- tpm@50 {
- compatible = "google,cr50";
- reg = <0x50>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&h1_ap_int_odl>;
-
- interrupt-parent = <&tlmm>;
- interrupts = <54 IRQ_TYPE_EDGE_RISING>;
- };
-};
-
-ap_ts_pen: &i2c13 {
- status = "okay";
- clock-frequency = <400000>;
-
- ap_ts: touchscreen@10 {
- compatible = "hid-over-i2c";
- reg = <0x10>;
- pinctrl-names = "default";
- pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
-
- interrupt-parent = <&tlmm>;
- interrupts = <81 IRQ_TYPE_LEVEL_LOW>;
-
- post-power-on-delay-ms = <20>;
- hid-descr-addr = <0x0001>;
-
- vdd-supply = <&pp3300_ts>;
- };
-};
-
-&pm7325_gpios {
- status = "disabled"; /* No GPIOs are connected */
-};
-
-&pmk8350_gpios {
- status = "disabled"; /* No GPIOs are connected */
-};
-
-&pmk8350_rtc {
- status = "disabled";
-};
-
-&pmk8350_vadc {
- pmk8350_die_temp {
- reg = <PMK8350_ADC7_DIE_TEMP>;
- label = "pmk8350_die_temp";
- qcom,pre-scaling = <1 1>;
- };
-
- pmr735a_die_temp {
- reg = <PMR735A_ADC7_DIE_TEMP>;
- label = "pmr735a_die_temp";
- qcom,pre-scaling = <1 1>;
- };
-};
-
-&qfprom {
- vcc-supply = <&vdd_qfprom>;
-};
-
-&qupv3_id_0 {
- status = "okay";
-};
-
-&qupv3_id_1 {
- status = "okay";
-};
-
-&sdhc_1 {
- status = "okay";
-
- vmmc-supply = <&pp2950_l7b>;
- vqmmc-supply = <&pp1800_l19b>;
-};
-
-&sdhc_2 {
- status = "okay";
-
- pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>, <&sd_cd>;
- pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>, <&sd_cd>;
- vmmc-supply = <&pp2950_l9c>;
- vqmmc-supply = <&ppvar_l6c>;
-
- cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
-};
-
-ap_ec_spi: &spi8 {
- status = "okay";
-
- pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs_gpio_init_high>, <&qup_spi8_cs_gpio>;
- cs-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
-
- cros_ec: ec@0 {
- compatible = "google,cros-ec-spi";
- reg = <0>;
- interrupt-parent = <&tlmm>;
- interrupts = <142 IRQ_TYPE_LEVEL_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&ap_ec_int_l>;
- spi-max-frequency = <3000000>;
-
- cros_ec_pwm: pwm {
- compatible = "google,cros-ec-pwm";
- #pwm-cells = <1>;
- };
-
- i2c_tunnel: i2c-tunnel {
- compatible = "google,cros-ec-i2c-tunnel";
- google,remote-bus = <0>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- typec {
- compatible = "google,cros-ec-typec";
- #address-cells = <1>;
- #size-cells = <0>;
-
- usb_c0: connector@0 {
- compatible = "usb-c-connector";
- reg = <0>;
- label = "left";
- power-role = "dual";
- data-role = "host";
- try-power-role = "source";
- };
-
- usb_c1: connector@1 {
- compatible = "usb-c-connector";
- reg = <1>;
- label = "right";
- power-role = "dual";
- data-role = "host";
- try-power-role = "source";
- };
- };
- };
-};
-
-#include <arm/cros-ec-keyboard.dtsi>
-#include <arm/cros-ec-sbs.dtsi>
-
-&keyboard_controller {
- function-row-physmap = <
- MATRIX_KEY(0x00, 0x02, 0) /* T1 */
- MATRIX_KEY(0x03, 0x02, 0) /* T2 */
- MATRIX_KEY(0x02, 0x02, 0) /* T3 */
- MATRIX_KEY(0x01, 0x02, 0) /* T4 */
- MATRIX_KEY(0x03, 0x04, 0) /* T5 */
- MATRIX_KEY(0x02, 0x04, 0) /* T6 */
- MATRIX_KEY(0x01, 0x04, 0) /* T7 */
- MATRIX_KEY(0x02, 0x09, 0) /* T8 */
- MATRIX_KEY(0x01, 0x09, 0) /* T9 */
- MATRIX_KEY(0x00, 0x04, 0) /* T10 */
- >;
- linux,keymap = <
- MATRIX_KEY(0x00, 0x02, KEY_BACK)
- MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
- MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
- MATRIX_KEY(0x01, 0x02, KEY_SCALE)
- MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
- MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
- MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
- MATRIX_KEY(0x02, 0x09, KEY_MUTE)
- MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
- MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
-
- CROS_STD_MAIN_KEYMAP
- >;
-};
-
-&uart5 {
- compatible = "qcom,geni-debug-uart";
- status = "okay";
-};
-
-&uart7 {
- status = "okay";
-};
-
-&usb_1 {
- status = "okay";
-};
-
-&usb_1_dwc3 {
- dr_mode = "host";
-};
-
-&usb_1_hsphy {
- status = "okay";
-
- vdda-pll-supply = <&vdd_usb_hs0_core>;
- vdda33-supply = <&vdda_usb_hs0_3p1>;
- vdda18-supply = <&vdda_usb_hs0_1p8>;
-};
-
-&usb_1_qmpphy {
- status = "okay";
-
- vdda-phy-supply = <&vdda_usb_ss_dp_1p2>;
- vdda-pll-supply = <&vdda_usb_ss_dp_core>;
-};
-
-&usb_2 {
- status = "okay";
-};
-
-&usb_2_dwc3 {
- dr_mode = "host";
-};
-
-&usb_2_hsphy {
- status = "okay";
-
- vdda-pll-supply = <&vdd_usb_hs0_core>;
- vdda33-supply = <&vdda_usb_hs0_3p1>;
- vdda18-supply = <&vdda_usb_hs0_1p8>;
-};
-
-/* PINCTRL - additions to nodes defined in sc7280.dtsi */
-
-&dp_hot_plug_det {
- bias-disable;
-};
-
-&pcie1_clkreq_n {
- bias-pull-up;
- drive-strength = <2>;
-};
-
-&qspi_cs0 {
- bias-disable;
-};
-
-&qspi_clk {
- bias-disable;
-};
-
-&qspi_data01 {
- /* High-Z when no transfers; nice to park the lines */
- bias-pull-up;
-};
-
-&qup_uart5_rx {
- drive-strength = <2>;
- bias-pull-up;
-};
-
-&qup_uart5_tx {
- drive-strength = <2>;
- bias-disable;
-};
-
-&qup_uart7_cts {
- /*
- * Configure a pull-down on CTS to match the pull of
- * the Bluetooth module.
- */
- bias-pull-down;
-};
-
-&qup_uart7_rts {
- /* We'll drive RTS, so no pull */
- drive-strength = <2>;
- bias-disable;
-};
-
-&qup_uart7_tx {
- /* We'll drive TX, so no pull */
- drive-strength = <2>;
- bias-disable;
-};
-
-&qup_uart7_rx {
- /*
- * Configure a pull-up on RX. This is needed to avoid
- * garbage data when the TX pin of the Bluetooth module is
- * in tri-state (module powered off or not driving the
- * signal yet).
- */
- bias-pull-up;
-};
-
-&sdc1_clk {
- bias-disable;
- drive-strength = <16>;
-};
-
-&sdc1_cmd {
- bias-pull-up;
- drive-strength = <10>;
-};
-
-&sdc1_data {
- bias-pull-up;
- drive-strength = <10>;
-};
-
-&sdc1_rclk {
- bias-pull-down;
-};
-
-&sdc2_clk {
- bias-disable;
- drive-strength = <16>;
-};
-
-&sdc2_cmd {
- bias-pull-up;
- drive-strength = <10>;
-};
-
-&sdc2_data {
- bias-pull-up;
- drive-strength = <10>;
-};
-
-/* PINCTRL - board-specific pinctrl */
-
-&pm8350c_gpios {
- gpio-line-names = "AP_SUSPEND",
- "",
- "",
- "AP_BL_EN",
- "",
- "SD_CD_ODL",
- "",
- "",
- "AP_BL_PWM";
-
- ap_bl_en: ap-bl-en {
- pins = "gpio4";
- function = "normal";
- qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
- bias-disable;
-
- /* Force backlight to be disabled to match state at boot. */
- output-low;
- };
-};
-
-&tlmm {
- gpio-line-names = "HP_I2C_SDA", /* 0 */
- "HP_I2C_SCL",
- "SSD_RST_L",
- "PE_WAKE_ODL",
- "AP_TP_I2C_SDA",
- "AP_TP_I2C_SCL",
- "UF_CAM_EN",
- "WF_CAM_EN",
- "AP_SAR_SENSOR_SDA",
- "AP_SAR_SENSOR_SCL",
-
- "", /* 10 */
- "",
- "AP_SPI_MOSI",
- "AP_SPI_MISO",
- "AP_SPI_CLK",
- "AP_SPI_CS0_L",
- "",
- "",
- "EDP_HPD",
- "",
-
- "UF_CAM_RST_L", /* 20 */
- "WF_CAM_RST_L",
- "UART_AP_TX_DBG_RX",
- "UART_DBG_TX_AP_RX",
- "EN_PP3300_HUB",
- "",
- "HOST2WLAN_SOL",
- "WLAN2HOST_SOL",
- "BT_UART_CTS",
- "BT_UART_RTS",
-
- "BT_UART_TXD", /* 30 */
- "BT_UART_RXD",
- "AP_EC_SPI_MISO",
- "AP_EC_SPI_MOSI",
- "AP_EC_SPI_CLK",
- "AP_EC_SPI_CS_L",
- "",
- "",
- "",
- "PEN_PDCT_L",
-
- "IO_BRD_ID0", /* 40 */
- "IO_BRD_ID1",
- "EN_FP_RAILS",
- "PEN_IRQ_L",
- "AP_SPI_FP_MISO",
- "AP_SPI_FP_MOSI",
- "AP_SPI_FP_CLK",
- "AP_SPI_FP_CS_L",
- "AP_H1_SPI_MISO",
- "AP_H1_SPI_MOSI",
-
- "AP_H1_SPI_CLK", /* 50 */
- "AP_H1_SPI_CS_L",
- "AP_TS_PEN_I2C_SDA",
- "AP_TS_PEN_I2C_SCL",
- "H1_AP_INT_ODL",
- "",
- "LCM_RST_1V8_L",
- "AMP_EN",
- "",
- "DP_HOT_PLUG_DET",
-
- "HUB_RST_L", /* 60 */
- "FP_TO_AP_IRQ_L",
- "",
- "",
- "UF_CAM_MCLK",
- "WF_CAM_MCLK",
- "IO_BRD_ID2",
- "EN_PP3300_CODEC",
- "EC_IN_RW_ODL",
- "UF_CAM_SDA",
-
- "UF_CAM_SCL", /* 70 */
- "WF_CAM_SDA",
- "WF_CAM_SCL",
- "AP_BRD_ID0",
- "AP_BRD_ID1",
- "AP_BRD_ID2",
- "",
- "FPMCU_BOOT0",
- "FP_RST_L",
- "PE_CLKREQ_ODL",
-
- "EN_EDP_PP3300", /* 80 */
- "TS_INT_L",
- "FORCE_USB_BOOT",
- "WCD_RST_L",
- "WLAN_EN",
- "BT_EN",
- "WLAN_SW_CTRL",
- "PCIE0_RESET_L",
- "PCIE0_CLK_REQ_L",
- "PCIE0_WAKE_L",
-
- "AS_EN", /* 90 */
- "SD_CD_ODL",
- "",
- /*
- * AP_FLASH_WP_L is crossystem ABI. Schematics
- * call it BIOS_FLASH_WP_L.
- */
- "AP_FLASH_WP_L",
- "BT_WLAN_SB_CLK",
- "BT_WLAN_SB_DATA",
- "HP_MCLK",
- "HP_BCLK",
- "HP_DOUT",
- "HP_DIN",
-
- "HP_LRCLK", /* 100 */
- "HP_IRQ",
- "TP_INT_ODL",
- "",
- "IO_SKU_ID2",
- "TS_RESET_L",
- "AMP_BCLK",
- "AMP_DIN",
- "AMP_LRCLK",
- "UIM2_DATA",
-
- "UIM2_CLK", /* 110 */
- "UIM2_RST",
- "UIM2_PRESENT",
- "UIM1_DATA",
- "UIM1_CLK",
- "UIM1_RST",
- "",
- "RFFE0_CLK",
- "RFFE0_DATA/BOOT_CONFIG_0",
- "RFFE1_CLK",
-
- "RFFE1_DATA/BOOT_CONFIG_1", /* 120 */
- "RFFE2_CLK",
- "RFFE2_DATA/BOOT_CONFIG_2",
- "RFFE3_CLK",
- "RFFE3_DATA/BOOT_CONFIG_3",
- "RFFE4_CLK",
- "RFFE4_DATA",
- "WCI2_LTE_COEX_RXD",
- "WCI2_LTE_COEX_TXD",
- "IO_SKU_ID0",
-
- "IO_SKU_ID1", /* 130 */
- "",
- "",
- "QLINK0_REQ",
- "QLINK0_EN",
- "QLINK0_WMSS_RESET_L",
- "QLINK1_REQ",
- "QLINK1_EN",
- "QLINK1_WMSS_RESET_L",
- "FORCED_USB_BOOT_POL",
-
- "", /* 140 */
- "P_SENSOR_INT_L",
- "AP_EC_INT_L",
- "",
- "WCD_SWR_TX_CLK",
- "WCD_SWR_TX_DATA_0",
- "WCD_SWR_TX_DATA_1",
- "WCD_SWR_RX_CLK",
- "WCD_SWR_RX_DATA_0",
- "WCD_SWR_RX_DATA_1",
-
- "", /* 150 */
- "",
- "",
- "",
- "",
- "",
- "",
- "",
- "WCD_SWR_TX_DATA_2",
- "",
-
- "", /* 160 */
- "",
- "",
- "",
- "",
- "",
- "",
- "",
- "",
- "",
-
- "", /* 170 */
- "SENS_UART_TXD",
- "SENS_UART_RXD",
- "",
- "",
- "";
-
- /*
- * pinctrl settings for pins that have no real owners.
- */
- pinctrl-names = "default";
- pinctrl-0 = <&bios_flash_wp_l>;
-
- amp_en: amp-en {
- pins = "gpio57";
- function = "gpio";
- bias-pull-down;
- };
-
- ap_ec_int_l: ap-ec-int-l {
- pins = "gpio142";
- input-enable;
- bias-pull-up;
- };
-
- bios_flash_wp_l: bios-flash-wp-l {
- pins = "gpio93";
- function = "gpio";
- input-enable;
- bias-disable;
- };
-
- bt_en: bt-en {
- pins = "gpio85";
- function = "gpio";
- drive-strength = <2>;
- output-low;
- bias-pull-down;
- };
-
- en_fp_rails: en-fp-rails {
- pins = "gpio42";
- drive-strength = <2>;
- output-high;
- bias-disable;
- };
-
- en_pp3300_codec: en-pp3300-codec {
- pins = "gpio67";
- drive-strength = <2>;
- bias-disable;
- };
-
- en_pp3300_dx_edp: en-pp3300-dx-edp {
- pins = "gpio80";
- function = "gpio";
- drive-strength = <2>;
- /* Has external pulldown */
- bias-disable;
- };
-
- en_pp3300_hub: en-pp3300-hub {
- pins = "gpio24";
- function = "gpio";
- drive-strength = <2>;
- /* Has external pulldown */
- bias-disable;
- };
-
- fp_to_ap_irq_l: fp-to-ap-irq-l {
- pins = "gpio61";
- function = "gpio";
- input-enable;
- /* Has external pullup */
- bias-disable;
- };
-
- h1_ap_int_odl: h1-ap-int-odl {
- pins = "gpio54";
- function = "gpio";
- input-enable;
- bias-pull-up;
- };
-
- hp_irq: hp-irq {
- pins = "gpio101";
- function = "gpio";
- bias-pull-up;
- };
-
- p_sensor_int_l: p-sensor-int-l {
- pins = "gpio141";
- function = "gpio";
- input-enable;
- bias-pull-up;
- };
-
- pen_irq_l: pen-irq-l {
- pins = "gpio43";
- function = "gpio";
- /* Has external pullup */
- bias-disable;
- };
-
- pen_pdct_l: pen-pdct-l {
- pins = "gpio39";
- function = "gpio";
- /* Has external pullup */
- bias-disable;
- };
-
- qup_spi8_cs_gpio_init_high: qup-spi8-cs-gpio-init-high {
- pins = "gpio35";
- output-high;
- };
-
- qup_spi11_cs_gpio_init_high: qup-spi11-cs-gpio-init-high {
- pins = "gpio47";
- output-high;
- };
-
- qup_spi12_cs_gpio_init_high: qup-spi12-cs-gpio-init-high {
- pins = "gpio51";
- output-high;
- };
-
- qup_uart7_sleep_cts: qup-uart7-sleep-cts {
- pins = "gpio28";
- function = "gpio";
- /*
- * Configure a pull-down on CTS to match the pull of
- * the Bluetooth module.
- */
- bias-pull-down;
- };
-
- qup_uart7_sleep_rts: qup-uart7-sleep-rts {
- pins = "gpio29";
- function = "gpio";
- /*
- * Configure pull-down on RTS. As RTS is active low
- * signal, pull it low to indicate the BT SoC that it
- * can wakeup the system anytime from suspend state by
- * pulling RX low (by sending wakeup bytes).
- */
- bias-pull-down;
- };
-
- qup_uart7_sleep_rx: qup-uart7-sleep-rx {
- pins = "gpio31";
- function = "gpio";
- /*
- * Configure a pull-up on RX. This is needed to avoid
- * garbage data when the TX pin of the Bluetooth module
- * is floating which may cause spurious wakeups.
- */
- bias-pull-up;
- };
-
- qup_uart7_sleep_tx: qup-uart7-sleep-tx {
- pins = "gpio30";
- function = "gpio";
- /*
- * Configure pull-up on TX when it isn't actively driven
- * to prevent BT SoC from receiving garbage during sleep.
- */
- bias-pull-up;
- };
-
- sd_cd: sd-cd {
- pins = "gpio91";
- function = "gpio";
- bias-pull-up;
- };
-
- tp_int_odl: tp-int-odl {
- pins = "gpio102";
- function = "gpio";
- /* Has external pullup */
- bias-disable;
- };
-
- ts_int_l: ts-int-l {
- pins = "gpio81";
- function = "gpio";
- /* Has external pullup */
- bias-pull-up;
- };
-
- ts_reset_l: ts-reset-l {
- pins = "gpio105";
- function = "gpio";
- /* Has external pullup */
- bias-disable;
- drive-strength = <2>;
- };
-
- uf_cam_en: uf-cam-en {
- pins = "gpio6";
- function = "gpio";
- drive-strength = <2>;
- /* Has external pulldown */
- bias-disable;
- };
-
- wf_cam_en: wf-cam-en {
- pins = "gpio7";
- function = "gpio";
- drive-strength = <2>;
- /* Has external pulldown */
- bias-disable;
- };
-};
As talked about in commit 61a6262f95e0 ("arm64: dts: qcom: sc7280: Move herobrine-r0 to its own dts"), herobrine evolved pretty significantly after -r0 and newer revisions are pretty different. Nobody needs the old boards to keep working, so let's delete to avoid the maintenance burden. Signed-off-by: Douglas Anderson <dianders@chromium.org> --- arch/arm64/boot/dts/qcom/Makefile | 1 - .../qcom/sc7280-herobrine-herobrine-r0.dts | 1352 ----------------- 2 files changed, 1353 deletions(-) delete mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r0.dts