diff mbox series

[v5,1/3] dt-bindings: phy: qcom, usb-snps-femto-v2: Add phy override params bindings

Message ID 1652723410-1630-2-git-send-email-quic_kriskura@quicinc.com
State Superseded
Headers show
Series Add QCOM SNPS PHY overriding params support | expand

Commit Message

Krishna Kurapati May 16, 2022, 5:50 p.m. UTC 
From: Sandeep Maheswaram <quic_c_sanm@quicinc.com>

Add device tree bindings for SNPS phy tuning parameters.

Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
---
 .../bindings/phy/qcom,usb-snps-femto-v2.yaml       | 105 +++++++++++++++++++++
 1 file changed, 105 insertions(+)

Comments

Krzysztof Kozlowski May 17, 2022, 6:23 a.m. UTC | #1 
On 16/05/2022 19:50, Krishna Kurapati wrote:
> From: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
> 
> Add device tree bindings for SNPS phy tuning parameters.
> 
> Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
> ---
>  .../bindings/phy/qcom,usb-snps-femto-v2.yaml       | 105 +++++++++++++++++++++
>  1 file changed, 105 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
> index 1ce251d..0a78db7 100644
> --- a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
> +++ b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
> @@ -53,6 +53,111 @@ properties:
>    vdda33-supply:
>      description: phandle to the regulator 3.3V supply node.
>  
> +  qcom,hs-disconnect-bp:
> +    $ref: /schemas/types.yaml#/definitions/int32

No need for ref for standard units.

> +    description:
> +      This adjusts the voltage level for the threshold used to
> +      detect a disconnect event at the host. Possible values are.
> +      The values defined are in multiples of basis points (1bp = 0.01%).
> +      The hardware accepts only discrete values. The value closest to the
> +      provided input will be chosen as the override value for this param.
> +    minimum: -272
> +    maximum: 2156
> +
> +  qcom,squelch-detector-bp:
> +    $ref: /schemas/types.yaml#/definitions/int32
> +    description:
> +      This adjusts the voltage level for the threshold used to
> +      detect valid high-speed data.
> +      The values defined are in multiples of basis points (1bp = 0.01%).
> +      The hardware accepts only discrete values. The value closest to the
> +      provided input will be chosen as the override value for this param.
> +    minimum: -2090
> +    maximum: 1590
> +
> +  qcom,hs-amplitude-bp:
> +    $ref: /schemas/types.yaml#/definitions/int32
> +    description:
> +      This adjusts the high-speed DC level voltage.
> +      The values defined are in multiples of basis points (1bp = 0.01%).
> +      The hardware accepts only discrete values. The value closest to the
> +      provided input will be chosen as the override value for this param.
> +    minimum: -660
> +    maximum: 2670
> +
> +  qcom,pre-emphasis-duration-bp:
> +    $ref: /schemas/types.yaml#/definitions/int32
> +    description:
> +      This signal controls the duration for which the
> +      HS pre-emphasis current is sourced onto DP<#> or DM<#>.
> +      The HS Transmitter pre-emphasis duration is defined in terms of
> +      unit amounts. One unit of pre-emphasis duration is approximately
> +      650 ps and is defined as 1X pre-emphasis duration.
> +      The values defined are in multiples of basis points (1bp = 0.01%).
> +      The hardware accepts only discrete values. The value closest to the
> +      provided input will be chosen as the override value for this param.
> +    minimum: 10000
> +    maximum: 20000
> +
> +  qcom,pre-emphasis-amplitude-bp:
> +    $ref: /schemas/types.yaml#/definitions/int32
> +    description:
> +      This signal controls the amount of current sourced to
> +      DP<#> and DM<#> after a J-to-K or K-to-J transition.
> +      The HS Transmitter pre-emphasis current is defined in terms of unit
> +      amounts. One unit amount is approximately 2 mA and is defined as
> +      1X pre-emphasis current.
> +      The values defined are in multiples of basis points (1bp = 0.01%).
> +      The hardware accepts only discrete values. The value closest to the
> +      provided input will be chosen as the override value for this param.
> +    minimum: 10000
> +    maximum: 40000
> +
> +  qcom,hs-rise-fall-time-bp:
> +    $ref: /schemas/types.yaml#/definitions/int32
> +    description:
> +      This adjusts the rise/fall times of the high-speed waveform.
> +      The values defined are in multiples of basis points (1bp = 0.01%).
> +      The hardware accepts only discrete values. The value closest to the
> +      provided input will be chosen as the override value for this param.
> +    minimim: -4100
> +    maximum: 5430
> +
> +  qcom,hs-crossover-voltage-microvolt:
> +    $ref: /schemas/types.yaml#/definitions/int32
> +    description:
> +      This adjusts the voltage at which the DP<#> and DM<#>
> +      signals cross while transmitting in HS mode.
> +      The values defined are in milli volts. The hardware accepts only
> +      discrete values. The value closest to the provided input will be
> +      chosen as the override value for this param.
> +    minimum: -31000
> +    maximum: 28000
> +
> +  qcom,hs-output-impedance-micro-ohm:

Please use standard unit suffixes, so micro-ohms.


Best regards,
Krzysztof
Rob Herring (Arm) May 17, 2022, 12:40 p.m. UTC | #2 
On Mon, 16 May 2022 23:20:08 +0530, Krishna Kurapati wrote:
> From: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
> 
> Add device tree bindings for SNPS phy tuning parameters.
> 
> Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
> ---
>  .../bindings/phy/qcom,usb-snps-femto-v2.yaml       | 105 +++++++++++++++++++++
>  1 file changed, 105 insertions(+)
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml: properties:qcom,hs-rise-fall-time-bp: 'minimim' is not one of ['$ref', 'additionalItems', 'additionalProperties', 'allOf', 'anyOf', 'const', 'contains', 'default', 'dependencies', 'dependentRequired', 'dependentSchemas', 'deprecated', 'description', 'else', 'enum', 'exclusiveMaximum', 'exclusiveMinimum', 'items', 'if', 'minItems', 'minimum', 'maxItems', 'maximum', 'multipleOf', 'not', 'oneOf', 'pattern', 'patternProperties', 'properties', 'required', 'then', 'type', 'typeSize', 'unevaluatedProperties', 'uniqueItems']
	from schema $id: http://devicetree.org/meta-schemas/keywords.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml: properties:qcom,hs-crossover-voltage-microvolt: '$ref' should not be valid under {'const': '$ref'}
	hint: Standard unit suffix properties don't need a type $ref
	from schema $id: http://devicetree.org/meta-schemas/core.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml: ignoring, error in schema: properties: qcom,hs-rise-fall-time-bp
Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.example.dtb:0:0: /example-0/phy@88e2000: failed to match any schema with compatible: ['qcom,sm8150-usb-hs-phy']

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
index 1ce251d..0a78db7 100644
--- a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
@@ -53,6 +53,111 @@  properties:
   vdda33-supply:
     description: phandle to the regulator 3.3V supply node.
 
+  qcom,hs-disconnect-bp:
+    $ref: /schemas/types.yaml#/definitions/int32
+    description:
+      This adjusts the voltage level for the threshold used to
+      detect a disconnect event at the host. Possible values are.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: -272
+    maximum: 2156
+
+  qcom,squelch-detector-bp:
+    $ref: /schemas/types.yaml#/definitions/int32
+    description:
+      This adjusts the voltage level for the threshold used to
+      detect valid high-speed data.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: -2090
+    maximum: 1590
+
+  qcom,hs-amplitude-bp:
+    $ref: /schemas/types.yaml#/definitions/int32
+    description:
+      This adjusts the high-speed DC level voltage.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: -660
+    maximum: 2670
+
+  qcom,pre-emphasis-duration-bp:
+    $ref: /schemas/types.yaml#/definitions/int32
+    description:
+      This signal controls the duration for which the
+      HS pre-emphasis current is sourced onto DP<#> or DM<#>.
+      The HS Transmitter pre-emphasis duration is defined in terms of
+      unit amounts. One unit of pre-emphasis duration is approximately
+      650 ps and is defined as 1X pre-emphasis duration.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: 10000
+    maximum: 20000
+
+  qcom,pre-emphasis-amplitude-bp:
+    $ref: /schemas/types.yaml#/definitions/int32
+    description:
+      This signal controls the amount of current sourced to
+      DP<#> and DM<#> after a J-to-K or K-to-J transition.
+      The HS Transmitter pre-emphasis current is defined in terms of unit
+      amounts. One unit amount is approximately 2 mA and is defined as
+      1X pre-emphasis current.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: 10000
+    maximum: 40000
+
+  qcom,hs-rise-fall-time-bp:
+    $ref: /schemas/types.yaml#/definitions/int32
+    description:
+      This adjusts the rise/fall times of the high-speed waveform.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimim: -4100
+    maximum: 5430
+
+  qcom,hs-crossover-voltage-microvolt:
+    $ref: /schemas/types.yaml#/definitions/int32
+    description:
+      This adjusts the voltage at which the DP<#> and DM<#>
+      signals cross while transmitting in HS mode.
+      The values defined are in milli volts. The hardware accepts only
+      discrete values. The value closest to the provided input will be
+      chosen as the override value for this param.
+    minimum: -31000
+    maximum: 28000
+
+  qcom,hs-output-impedance-micro-ohm:
+    $ref: /schemas/types.yaml#/definitions/int32
+    description:
+      In some applications, there can be significant series resistance
+      on the D+ and D- paths between the transceiver and cable. This adjusts
+      the driver source impedance to compensate for added series
+      resistance on the USB. The values defined are in milli ohms.
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: -2300000
+    maximum: 6100000
+
+  qcom,ls-fs-output-impedance-bp:
+    $ref: /schemas/types.yaml#/definitions/int32
+    description:
+      This adjusts the low- and full-speed single-ended source
+      impedance while driving high. The following adjustment values are based
+      on nominal process, voltage, and temperature.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: -1053
+    maximum: 1310
+
 required:
   - compatible
   - reg