@@ -265,6 +265,7 @@ static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi,
#define MX51_ECSPI_CONFIG_SBBCTRL(cs) (1 << ((cs) + 8))
#define MX51_ECSPI_CONFIG_SSBPOL(cs) (1 << ((cs) + 12))
#define MX51_ECSPI_CONFIG_SCLKCTL(cs) (1 << ((cs) + 20))
+#define MX51_ECSPI_MAX_HW_CS 4
#define MX51_ECSPI_INT 0x10
#define MX51_ECSPI_INT_TEEN (1 << 0)
@@ -515,6 +516,7 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
u32 min_speed_hz = ~0U;
u32 testreg, delay;
u32 cfg = readl(spi_imx->base + MX51_ECSPI_CONFIG);
+ int chip_select;
/* set Master or Slave mode */
if (spi_imx->slave_mode)
@@ -528,8 +530,19 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
if (spi->mode & SPI_READY)
ctrl |= MX51_ECSPI_CTRL_DRCTL(spi_imx->spi_drctl);
- /* set chip select to use */
- ctrl |= MX51_ECSPI_CTRL_CS(spi->chip_select);
+ if (spi->cs_gpiod) {
+ chip_select = 0;
+ } else {
+ if (spi->chip_select >= MX51_ECSPI_MAX_HW_CS) {
+ dev_err(spi_imx->dev, "Native chip_select is out of supported range: %i\n",
+ spi->chip_select);
+ return -EINVAL;
+ }
+
+ /* set HW chip select to use */
+ ctrl |= MX51_ECSPI_CTRL_CS(spi->chip_select);
+ chip_select = spi->chip_select;
+ }
/*
* The ctrl register must be written first, with the EN bit set other
@@ -550,27 +563,27 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
* BURST_LENGTH + 1 bits are received
*/
if (spi_imx->slave_mode && is_imx53_ecspi(spi_imx))
- cfg &= ~MX51_ECSPI_CONFIG_SBBCTRL(spi->chip_select);
+ cfg &= ~MX51_ECSPI_CONFIG_SBBCTRL(chip_select);
else
- cfg |= MX51_ECSPI_CONFIG_SBBCTRL(spi->chip_select);
+ cfg |= MX51_ECSPI_CONFIG_SBBCTRL(chip_select);
if (spi->mode & SPI_CPHA)
- cfg |= MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select);
+ cfg |= MX51_ECSPI_CONFIG_SCLKPHA(chip_select);
else
- cfg &= ~MX51_ECSPI_CONFIG_SCLKPHA(spi->chip_select);
+ cfg &= ~MX51_ECSPI_CONFIG_SCLKPHA(chip_select);
if (spi->mode & SPI_CPOL) {
- cfg |= MX51_ECSPI_CONFIG_SCLKPOL(spi->chip_select);
- cfg |= MX51_ECSPI_CONFIG_SCLKCTL(spi->chip_select);
+ cfg |= MX51_ECSPI_CONFIG_SCLKPOL(chip_select);
+ cfg |= MX51_ECSPI_CONFIG_SCLKCTL(chip_select);
} else {
- cfg &= ~MX51_ECSPI_CONFIG_SCLKPOL(spi->chip_select);
- cfg &= ~MX51_ECSPI_CONFIG_SCLKCTL(spi->chip_select);
+ cfg &= ~MX51_ECSPI_CONFIG_SCLKPOL(chip_select);
+ cfg &= ~MX51_ECSPI_CONFIG_SCLKCTL(chip_select);
}
if (spi->mode & SPI_CS_HIGH)
- cfg |= MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select);
+ cfg |= MX51_ECSPI_CONFIG_SSBPOL(chip_select);
else
- cfg &= ~MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select);
+ cfg &= ~MX51_ECSPI_CONFIG_SSBPOL(chip_select);
writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG);
Fix support for boards with more then 4 chip select lines. Other wise if CS > 4 is used, we will write trash to the clk configuration register. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- drivers/spi/spi-imx.c | 37 +++++++++++++++++++++++++------------ 1 file changed, 25 insertions(+), 12 deletions(-)