@@ -52,6 +52,7 @@ Contents:
ti/am65_nuss_cpsw_switchdev
ti/tlan
toshiba/spider_net
+ wangxun/txgbe
.. only:: subproject and html
new file mode 100644
@@ -0,0 +1,20 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+================================================================
+Linux Base Driver for WangXun(R) 10 Gigabit PCI Express Adapters
+================================================================
+
+WangXun 10 Gigabit Linux driver.
+Copyright (c) 2015 - 2022 Beijing WangXun Technology Co., Ltd.
+
+
+Contents
+========
+
+- Support
+
+
+Support
+=======
+If you got any problem, contact Wangxun support team via support@trustnetic.com
+and Cc: netdev.
@@ -21432,6 +21432,13 @@ L: linux-input@vger.kernel.org
S: Maintained
F: drivers/input/tablet/wacom_serial4.c
+WANGXUN ETHERNET DRIVER
+M: Jiawen Wu <jiawenwu@trustnetic.com>
+L: netdev@vger.kernel.org
+S: Maintained
+F: Documentation/networking/device_drivers/ethernet/wangxun/txgbe.rst
+F: drivers/net/ethernet/wangxun/
+
WATCHDOG DEVICE DRIVERS
M: Wim Van Sebroeck <wim@linux-watchdog.org>
M: Guenter Roeck <linux@roeck-us.net>
@@ -84,6 +84,7 @@ source "drivers/net/ethernet/huawei/Kconfig"
source "drivers/net/ethernet/i825xx/Kconfig"
source "drivers/net/ethernet/ibm/Kconfig"
source "drivers/net/ethernet/intel/Kconfig"
+source "drivers/net/ethernet/wangxun/Kconfig"
source "drivers/net/ethernet/xscale/Kconfig"
config JME
@@ -97,6 +97,7 @@ obj-$(CONFIG_NET_VENDOR_TOSHIBA) += toshiba/
obj-$(CONFIG_NET_VENDOR_TUNDRA) += tundra/
obj-$(CONFIG_NET_VENDOR_VERTEXCOM) += vertexcom/
obj-$(CONFIG_NET_VENDOR_VIA) += via/
+obj-$(CONFIG_NET_VENDOR_WANGXUN) += wangxun/
obj-$(CONFIG_NET_VENDOR_WIZNET) += wiznet/
obj-$(CONFIG_NET_VENDOR_XILINX) += xilinx/
obj-$(CONFIG_NET_VENDOR_XIRCOM) += xircom/
new file mode 100644
@@ -0,0 +1,32 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Wangxun network device configuration
+#
+
+config NET_VENDOR_WANGXUN
+ bool "Wangxun devices"
+ default y
+ help
+ If you have a network (Ethernet) card belonging to this class, say Y.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about Intel cards. If you say Y, you will be asked for
+ your specific card in the following questions.
+
+if NET_VENDOR_WANGXUN
+
+config TXGBE
+ tristate "Wangxun(R) 10GbE PCI Express adapters support"
+ depends on PCI
+ help
+ This driver supports Wangxun(R) 10GbE PCI Express family of
+ adapters.
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/device_drivers/ethernet/wangxun/txgbe.rst>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called txgbe.
+
+endif # NET_VENDOR_WANGXUN
new file mode 100644
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the Wangxun network device drivers.
+#
+
+obj-$(CONFIG_TXGBE) += txgbe/
new file mode 100644
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (c) 2015 - 2022 Beijing WangXun Technology Co., Ltd.
+#
+# Makefile for the Wangxun(R) 10GbE PCI Express ethernet driver
+#
+
+obj-$(CONFIG_TXGBE) += txgbe.o
+
+txgbe-objs := txgbe_main.o
new file mode 100644
@@ -0,0 +1,24 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (c) 2015 - 2022 Beijing WangXun Technology Co., Ltd. */
+
+#ifndef _TXGBE_H_
+#define _TXGBE_H_
+
+#include "txgbe_type.h"
+
+#define TXGBE_MAX_FDIR_INDICES 63
+
+#define TXGBE_MAX_RX_QUEUES (TXGBE_MAX_FDIR_INDICES + 1)
+#define TXGBE_MAX_TX_QUEUES (TXGBE_MAX_FDIR_INDICES + 1)
+
+/* board specific private data structure */
+struct txgbe_adapter {
+ u8 __iomem *io_addr; /* Mainly for iounmap use */
+ /* OS defined structs */
+ struct net_device *netdev;
+ struct pci_dev *pdev;
+};
+
+extern char txgbe_driver_name[];
+
+#endif /* _TXGBE_H_ */
new file mode 100644
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c) 2015 - 2022 Beijing WangXun Technology Co., Ltd. */
+
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/netdevice.h>
+#include <linux/string.h>
+#include <linux/aer.h>
+#include <linux/etherdevice.h>
+
+#include "txgbe.h"
+
+char txgbe_driver_name[] = "txgbe";
+
+/* txgbe_pci_tbl - PCI Device ID Table
+ *
+ * Wildcard entries (PCI_ANY_ID) should come last
+ * Last entry must be all 0s
+ *
+ * { Vendor ID, Device ID, SubVendor ID, SubDevice ID,
+ * Class, Class Mask, private data (not used) }
+ */
+static const struct pci_device_id txgbe_pci_tbl[] = {
+ { PCI_VDEVICE(WANGXUN, TXGBE_DEV_ID_SP1000), 0},
+ { PCI_VDEVICE(WANGXUN, TXGBE_DEV_ID_WX1820), 0},
+ /* required last entry */
+ { .device = 0 }
+};
+
+#define DEFAULT_DEBUG_LEVEL_SHIFT 3
+
+static void txgbe_dev_shutdown(struct pci_dev *pdev, bool *enable_wake)
+{
+ struct txgbe_adapter *adapter = pci_get_drvdata(pdev);
+ struct net_device *netdev = adapter->netdev;
+
+ netif_device_detach(netdev);
+
+ pci_disable_device(pdev);
+}
+
+static void txgbe_shutdown(struct pci_dev *pdev)
+{
+ bool wake;
+
+ txgbe_dev_shutdown(pdev, &wake);
+
+ if (system_state == SYSTEM_POWER_OFF) {
+ pci_wake_from_d3(pdev, wake);
+ pci_set_power_state(pdev, PCI_D3hot);
+ }
+}
+
+/**
+ * txgbe_probe - Device Initialization Routine
+ * @pdev: PCI device information struct
+ * @ent: entry in txgbe_pci_tbl
+ *
+ * Returns 0 on success, negative on failure
+ *
+ * txgbe_probe initializes an adapter identified by a pci_dev structure.
+ * The OS initialization, configuring of the adapter private structure,
+ * and a hardware reset occur.
+ **/
+static int txgbe_probe(struct pci_dev *pdev,
+ const struct pci_device_id __always_unused *ent)
+{
+ struct txgbe_adapter *adapter = NULL;
+ struct net_device *netdev;
+ int err, pci_using_dac;
+
+ err = pci_enable_device_mem(pdev);
+ if (err)
+ return err;
+
+ if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)) &&
+ !dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64))) {
+ pci_using_dac = 1;
+ } else {
+ err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
+ if (err) {
+ err = dma_set_coherent_mask(&pdev->dev,
+ DMA_BIT_MASK(32));
+ if (err) {
+ dev_err(&pdev->dev,
+ "No usable DMA configuration, aborting\n");
+ goto err_dma;
+ }
+ }
+ pci_using_dac = 0;
+ }
+
+ err = pci_request_selected_regions(pdev,
+ pci_select_bars(pdev, IORESOURCE_MEM),
+ txgbe_driver_name);
+ if (err) {
+ dev_err(&pdev->dev,
+ "pci_request_selected_regions failed 0x%x\n", err);
+ goto err_pci_reg;
+ }
+
+ pci_enable_pcie_error_reporting(pdev);
+ pci_set_master(pdev);
+
+ netdev = devm_alloc_etherdev_mqs(&pdev->dev,
+ sizeof(struct txgbe_adapter),
+ TXGBE_MAX_TX_QUEUES,
+ TXGBE_MAX_RX_QUEUES);
+ if (!netdev) {
+ err = -ENOMEM;
+ goto err_alloc_etherdev;
+ }
+
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+
+ adapter = netdev_priv(netdev);
+ adapter->netdev = netdev;
+ adapter->pdev = pdev;
+
+ adapter->io_addr = devm_ioremap(&pdev->dev,
+ pci_resource_start(pdev, 0),
+ pci_resource_len(pdev, 0));
+ if (!adapter->io_addr) {
+ err = -EIO;
+ goto err_ioremap;
+ }
+
+ if (pci_using_dac)
+ netdev->features |= NETIF_F_HIGHDMA;
+
+ pci_set_drvdata(pdev, adapter);
+
+ return 0;
+
+err_ioremap:
+err_alloc_etherdev:
+ pci_release_selected_regions(pdev,
+ pci_select_bars(pdev, IORESOURCE_MEM));
+err_pci_reg:
+err_dma:
+ pci_disable_device(pdev);
+ return err;
+}
+
+/**
+ * txgbe_remove - Device Removal Routine
+ * @pdev: PCI device information struct
+ *
+ * txgbe_remove is called by the PCI subsystem to alert the driver
+ * that it should release a PCI device. The could be caused by a
+ * Hot-Plug event, or because the driver is going to be removed from
+ * memory.
+ **/
+static void txgbe_remove(struct pci_dev *pdev)
+{
+ pci_release_selected_regions(pdev,
+ pci_select_bars(pdev, IORESOURCE_MEM));
+
+ pci_disable_pcie_error_reporting(pdev);
+
+ pci_disable_device(pdev);
+}
+
+static struct pci_driver txgbe_driver = {
+ .name = txgbe_driver_name,
+ .id_table = txgbe_pci_tbl,
+ .probe = txgbe_probe,
+ .remove = txgbe_remove,
+ .shutdown = txgbe_shutdown,
+};
+
+module_pci_driver(txgbe_driver);
+
+MODULE_DEVICE_TABLE(pci, txgbe_pci_tbl);
+MODULE_AUTHOR("Beijing WangXun Technology Co., Ltd, <software@trustnetic.com>");
+MODULE_DESCRIPTION("WangXun(R) 10 Gigabit PCI Express Network Driver");
+MODULE_LICENSE("GPL");
new file mode 100644
@@ -0,0 +1,57 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (c) 2015 - 2022 Beijing WangXun Technology Co., Ltd. */
+
+#ifndef _TXGBE_TYPE_H_
+#define _TXGBE_TYPE_H_
+
+#include <linux/types.h>
+#include <linux/netdevice.h>
+
+/************ txgbe_register.h ************/
+/* Vendor ID */
+#ifndef PCI_VENDOR_ID_WANGXUN
+#define PCI_VENDOR_ID_WANGXUN 0x8088
+#endif
+
+/* Device IDs */
+#define TXGBE_DEV_ID_SP1000 0x1001
+#define TXGBE_DEV_ID_WX1820 0x2001
+
+/* Subsystem IDs */
+/* SFP */
+#define TXGBE_ID_SP1000_SFP 0x0000
+#define TXGBE_ID_WX1820_SFP 0x2000
+#define TXGBE_ID_SFP 0x00
+
+/* copper */
+#define TXGBE_ID_SP1000_XAUI 0x1010
+#define TXGBE_ID_WX1820_XAUI 0x2010
+#define TXGBE_ID_XAUI 0x10
+#define TXGBE_ID_SP1000_SGMII 0x1020
+#define TXGBE_ID_WX1820_SGMII 0x2020
+#define TXGBE_ID_SGMII 0x20
+/* backplane */
+#define TXGBE_ID_SP1000_KR_KX_KX4 0x1030
+#define TXGBE_ID_WX1820_KR_KX_KX4 0x2030
+#define TXGBE_ID_KR_KX_KX4 0x30
+/* MAC Interface */
+#define TXGBE_ID_SP1000_MAC_XAUI 0x1040
+#define TXGBE_ID_WX1820_MAC_XAUI 0x2040
+#define TXGBE_ID_MAC_XAUI 0x40
+#define TXGBE_ID_SP1000_MAC_SGMII 0x1060
+#define TXGBE_ID_WX1820_MAC_SGMII 0x2060
+#define TXGBE_ID_MAC_SGMII 0x60
+
+#define TXGBE_NCSI_SUP 0x8000
+#define TXGBE_NCSI_MASK 0x8000
+#define TXGBE_WOL_SUP 0x4000
+#define TXGBE_WOL_MASK 0x4000
+#define TXGBE_DEV_MASK 0xf0
+
+/* Combined interface*/
+#define TXGBE_ID_SFI_XAUI 0x50
+
+/* Revision ID */
+#define TXGBE_SP_MPW 1
+
+#endif /* _TXGBE_TYPE_H_ */
@@ -5942,3 +5942,18 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56b1, aspm_l1_acceptable_latency
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56c0, aspm_l1_acceptable_latency);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56c1, aspm_l1_acceptable_latency);
#endif
+
+static void quirk_wangxun_set_read_req_size(struct pci_dev *pdev)
+{
+ u16 ctl;
+
+ pcie_capability_read_word(pdev, PCI_EXP_DEVCTL, &ctl);
+
+ if (((ctl & PCI_EXP_DEVCTL_READRQ) != PCI_EXP_DEVCTL_READRQ_128B) &&
+ ((ctl & PCI_EXP_DEVCTL_READRQ) != PCI_EXP_DEVCTL_READRQ_256B))
+ pcie_capability_clear_and_set_word(pdev, PCI_EXP_DEVCTL,
+ PCI_EXP_DEVCTL_READRQ,
+ PCI_EXP_DEVCTL_READRQ_256B);
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_WANGXUN, PCI_ANY_ID,
+ quirk_wangxun_set_read_req_size);
@@ -3105,4 +3105,6 @@
#define PCI_VENDOR_ID_NCUBE 0x10ff
+#define PCI_VENDOR_ID_WANGXUN 0x8088
+
#endif /* _LINUX_PCI_IDS_H */
Add doc build infrastructure for txgbe driver. Initialize PCI memory space for WangXun 10 Gigabit Ethernet devices. Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> --- Changelog: v6: address comments: Jakub Kicinski: make it build cleanly with W=1 C=1 v5: address comments: Andrew Lunn: repost the patch v4: address comments: Leon Romanovsky: remove unused data setting, add PCI quirk Andrew Lunn: remove devm_iounmap(), use module_pci_driver() v3: address comments: Andrew Lunn: https://lore.kernel.org/netdev/YoRkONdJlIU0ymd6@lunn.ch/ v2: address comments: Andrew Lunn & Jakub Kicinski: https://lore.kernel.org/netdev/Yn2E8X6f8PJ0c4CB@lunn.ch/ .../device_drivers/ethernet/index.rst | 1 + .../device_drivers/ethernet/wangxun/txgbe.rst | 20 ++ MAINTAINERS | 7 + drivers/net/ethernet/Kconfig | 1 + drivers/net/ethernet/Makefile | 1 + drivers/net/ethernet/wangxun/Kconfig | 32 ++++ drivers/net/ethernet/wangxun/Makefile | 6 + drivers/net/ethernet/wangxun/txgbe/Makefile | 9 + drivers/net/ethernet/wangxun/txgbe/txgbe.h | 24 +++ .../net/ethernet/wangxun/txgbe/txgbe_main.c | 178 ++++++++++++++++++ .../net/ethernet/wangxun/txgbe/txgbe_type.h | 57 ++++++ drivers/pci/quirks.c | 15 ++ include/linux/pci_ids.h | 2 + 13 files changed, 353 insertions(+) create mode 100644 Documentation/networking/device_drivers/ethernet/wangxun/txgbe.rst create mode 100644 drivers/net/ethernet/wangxun/Kconfig create mode 100644 drivers/net/ethernet/wangxun/Makefile create mode 100644 drivers/net/ethernet/wangxun/txgbe/Makefile create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe.h create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_main.c create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_type.h