[v4,00/14] Canaan devicetree fixes

Message

Conor Dooley July 1, 2022, 7:22 p.m. UTC

From: Conor Dooley <[e-mail]>

Hey all,
This series should rid us of dtbs_check errors for the RISC-V Canaan k210
based boards. To make keeping it that way a little easier, I changed the
Canaan devicetree Makefile so that it would build all of the devicetrees
in the directory if SOC_CANAAN.

I *DO NOT* have any Canaan hardware so I have not tested any of this in
action. Since I sent v1, I tried to buy some since it's cheap - but could
out of the limited stockists none seemed to want to deliver to Ireland :(
I based the series on next-20220617.

Thanks,
Conor.

Changes since v3:
- dts: drop the bogus "regs" property pointed out by Niklas
- dma/timer: add Serge's reviews (and expand on the dma interrupt
  description)
- dts: add Niklas' T-b where I felt it was suitable. lmk if you think it
  applies more broadly
- spi: drop the applied spi dt-binding change. Thanks Mark.

Changes since v2:
- i2s: added clocks maxItems
- dma: unconditionally extended the interrupts & dropped canaan
  compatible
- timer: as per Sergey, split the timer dts nodes in 2 & drop the
  binding patch
- ili9341: add a canaan specific compatible to the binding and dts

Changes since v1:
- I added a new dt node & compatible for the SRAM memory controller due
  Damien's wish to preserve the inter-op with U-Boot.
- The dw-apb-ssi binding now uses the default rx/tx widths
- A new patch fixes bus {ranges,reg} warnings
- Rearranged the patches in a slightly more logical order


Conor Dooley (14):
  dt-bindings: display: convert ilitek,ili9341.txt to dt-schema
  dt-bindings: display: ili9341: document canaan kd233's lcd
  ASoC: dt-bindings: convert designware-i2s to dt-schema
  dt-bindings: dma: dw-axi-dmac: extend the number of interrupts
  dt-bindings: memory-controllers: add canaan k210 sram controller
  riscv: dts: canaan: fix the k210's memory node
  riscv: dts: canaan: fix the k210's timer nodes
  riscv: dts: canaan: fix mmc node names
  riscv: dts: canaan: fix kd233 display spi frequency
  riscv: dts: canaan: use custom compatible for k210 i2s
  riscv: dts: canaan: remove spi-max-frequency from controllers
  riscv: dts: canaan: fix bus {ranges,reg} warnings
  riscv: dts: canaan: add specific compatible for kd233's LCD
  riscv: dts: canaan: build all devicetress if SOC_CANAAN

 .../bindings/display/ilitek,ili9341.txt       | 27 ------
 .../display/panel/ilitek,ili9341.yaml         | 49 +++++++---
 .../bindings/dma/snps,dw-axi-dmac.yaml        |  7 +-
 .../memory-controllers/canaan,k210-sram.yaml  | 52 ++++++++++
 .../bindings/sound/designware-i2s.txt         | 35 -------
 .../bindings/sound/snps,designware-i2s.yaml   | 94 +++++++++++++++++++
 arch/riscv/boot/dts/canaan/Makefile           | 10 +-
 arch/riscv/boot/dts/canaan/canaan_kd233.dts   |  6 +-
 arch/riscv/boot/dts/canaan/k210.dtsi          | 73 +++++++++-----
 .../riscv/boot/dts/canaan/sipeed_maix_bit.dts |  2 +-
 .../boot/dts/canaan/sipeed_maix_dock.dts      |  2 +-
 arch/riscv/boot/dts/canaan/sipeed_maix_go.dts |  2 +-
 .../boot/dts/canaan/sipeed_maixduino.dts      |  2 +-
 13 files changed, 253 insertions(+), 108 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/ilitek,ili9341.txt
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/canaan,k210-sram.yaml
 delete mode 100644 Documentation/devicetree/bindings/sound/designware-i2s.txt
 create mode 100644 Documentation/devicetree/bindings/sound/snps,designware-i2s.yaml


base-commit: 6cc11d2a1759275b856e464265823d94aabd5eaf

Comments

Mark Brown July 4, 2022, 3:57 p.m. UTC | #1

On Fri, 1 Jul 2022 20:22:46 +0100, Conor Dooley wrote:
> From: Conor Dooley <[e-mail]>
> 
> Hey all,
> This series should rid us of dtbs_check errors for the RISC-V Canaan k210
> based boards. To make keeping it that way a little easier, I changed the
> Canaan devicetree Makefile so that it would build all of the devicetrees
> in the directory if SOC_CANAAN.
> 
> [...]

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next

Thanks!

[03/14] ASoC: dt-bindings: convert designware-i2s to dt-schema
        commit: bc4c9d85179ca90679c8bb046cf7aad16fb88076

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark