new file mode 100644
@@ -0,0 +1,101 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/can/nxp,sja1000.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Memory mapped SJA1000 CAN controller from NXP (formerly Philips)
+
+maintainers:
+ - Wolfgang Grandegger <wg@grandegger.com>
+
+properties:
+ compatible:
+ enum:
+ - nxp,sja1000
+ - technologic,sja1000
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ reg-io-width:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: I/O register width (in bytes) implemented by this device
+ default: 1
+ enum: [ 1, 2, 4 ]
+
+ nxp,external-clock-frequency:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 16000000
+ description: |
+ Frequency of the external oscillator clock in Hz.
+ The internal clock frequency used by the SJA1000 is half of that value.
+
+ nxp,tx-output-mode:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 0, 1, 2, 3 ]
+ default: 1
+ description: |
+ operation mode of the TX output control logic. Valid values are:
+ <0> : bi-phase output mode
+ <1> : normal output mode (default)
+ <2> : test output mode
+ <3> : clock output mode
+
+ nxp,tx-output-config:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 0x02
+ description: |
+ TX output pin configuration. Valid values are any one of the below
+ or combination of TX0 and TX1:
+ <0x01> : TX0 invert
+ <0x02> : TX0 pull-down (default)
+ <0x04> : TX0 pull-up
+ <0x06> : TX0 push-pull
+ <0x08> : TX1 invert
+ <0x10> : TX1 pull-down
+ <0x20> : TX1 pull-up
+ <0x30> : TX1 push-pull
+
+ nxp,clock-out-frequency:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ clock frequency in Hz on the CLKOUT pin.
+ If not specified or if the specified value is 0, the CLKOUT pin
+ will be disabled.
+
+ nxp,no-comparator-bypass:
+ type: boolean
+ description: Allows to disable the CAN input comparator.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+allOf:
+ - $ref: can-controller.yaml#
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: technologic,sja1000
+ then:
+ required:
+ - reg-io-width
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ can@1a000 {
+ compatible = "technologic,sja1000";
+ reg = <0x1a000 0x100>;
+ interrupts = <1>;
+ reg-io-width = <2>;
+ nxp,tx-output-config = <0x06>;
+ nxp,external-clock-frequency = <24000000>;
+ };
deleted file mode 100644
@@ -1,58 +0,0 @@
-Memory mapped SJA1000 CAN controller from NXP (formerly Philips)
-
-Required properties:
-
-- compatible : should be one of "nxp,sja1000", "technologic,sja1000".
-
-- reg : should specify the chip select, address offset and size required
- to map the registers of the SJA1000. The size is usually 0x80.
-
-- interrupts: property with a value describing the interrupt source
- (number and sensitivity) required for the SJA1000.
-
-Optional properties:
-
-- reg-io-width : Specify the size (in bytes) of the IO accesses that
- should be performed on the device. Valid value is 1, 2 or 4.
- This property is ignored for technologic version.
- Default to 1 (8 bits).
-
-- nxp,external-clock-frequency : Frequency of the external oscillator
- clock in Hz. Note that the internal clock frequency used by the
- SJA1000 is half of that value. If not specified, a default value
- of 16000000 (16 MHz) is used.
-
-- nxp,tx-output-mode : operation mode of the TX output control logic:
- <0x0> : bi-phase output mode
- <0x1> : normal output mode (default)
- <0x2> : test output mode
- <0x3> : clock output mode
-
-- nxp,tx-output-config : TX output pin configuration:
- <0x01> : TX0 invert
- <0x02> : TX0 pull-down (default)
- <0x04> : TX0 pull-up
- <0x06> : TX0 push-pull
- <0x08> : TX1 invert
- <0x10> : TX1 pull-down
- <0x20> : TX1 pull-up
- <0x30> : TX1 push-pull
-
-- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin.
- If not specified or if the specified value is 0, the CLKOUT pin
- will be disabled.
-
-- nxp,no-comparator-bypass : Allows to disable the CAN input comparator.
-
-For further information, please have a look to the SJA1000 data sheet.
-
-Examples:
-
-can@3,100 {
- compatible = "nxp,sja1000";
- reg = <3 0x100 0x80>;
- interrupts = <2 0>;
- interrupt-parent = <&mpic>;
- nxp,external-clock-frequency = <16000000>;
-};
-
Convert the NXP SJA1000 CAN Controller Device Tree binding documentation to json-schema. Update the example to match reality. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> --- v3->v4: * Updated bindings as per coding style used in example-schema. * Entire entry in properties compatible declared as enum. Also Descriptions do not bring any information,so removed it from compatible description. * Used decimal values in nxp,tx-output-mode enums. * Fixed indentaions in example. v2->v3: * Added reg-io-width is a required property for technologic,sja1000 * Removed enum type from nxp,tx-output-config and updated the description for combination of TX0 and TX1. * Updated the example v1->v2: * Moved $ref: can-controller.yaml# to top along with if conditional to avoid multiple mapping issues with the if conditional in the subsequent patch. --- .../bindings/net/can/nxp,sja1000.yaml | 101 ++++++++++++++++++ .../devicetree/bindings/net/can/sja1000.txt | 58 ---------- 2 files changed, 101 insertions(+), 58 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/can/nxp,sja1000.yaml delete mode 100644 Documentation/devicetree/bindings/net/can/sja1000.txt