[v4,4/5] iio: pressure: bmp280: Add support for BMP380 sensor family

Message ID	50841287411a4e459487cc94a05bc6de66be4acf.1658597501.git.ang.iglesiasg@gmail.com (mailing list archive)
State	Changes Requested
Headers	show Return-Path: <linux-iio-owner@kernel.org> From: Angel Iglesias <ang.iglesiasg@gmail.com> To: linux-iio@vger.kernel.org Cc: Angel Iglesias <ang.iglesiasg@gmail.com>, Jonathan Cameron <jic23@kernel.org>, Lars-Peter Clausen <lars@metafoo.de>, Andy Shevchenko <andriy.shevchenko@linux.intel.com>, Nikita Yushchenko <nikita.yoush@cogentembedded.com>, "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>, Ulf Hansson <ulf.hansson@linaro.org>, Paul Cercueil <paul@crapouillou.net>, linux-kernel@vger.kernel.org Subject: [PATCH v4 4/5] iio: pressure: bmp280: Add support for BMP380 sensor family Date: Sat, 23 Jul 2022 19:39:44 +0200 Message-Id: <50841287411a4e459487cc94a05bc6de66be4acf.1658597501.git.ang.iglesiasg@gmail.com> In-Reply-To: <cover.1658597501.git.ang.iglesiasg@gmail.com> References: <cover.1658597501.git.ang.iglesiasg@gmail.com> MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Precedence: bulk
Series	Add support for pressure sensor Bosch BMP380 \| expand [v4,0/5] Add support for pressure sensor Bosch BMP380 [v4,1/5] dt-bindings: iio: pressure: bmp085: Add BMP380 compatible string [v4,2/5] iio: pressure: bmp280: simplify driver initialization logic [v4,3/5] iio: pressure: bmp280: Fix alignment for DMA safety [v4,4/5] iio: pressure: bmp280: Add support for BMP380 sensor family [v4,5/5] iio: pressure: bmp280: Add more tunable config parameters for BMP380

diff --git a/drivers/iio/pressure/Kconfig b/drivers/iio/pressure/Kconfig index 0ff756cea63a..c9453389e4f7 100644 --- a/drivers/iio/pressure/Kconfig +++ b/drivers/iio/pressure/Kconfig @@ -17,14 +17,14 @@ config ABP060MG will be called abp060mg. config BMP280 - tristate "Bosch Sensortec BMP180/BMP280 pressure sensor I2C driver" + tristate "Bosch Sensortec BMP180/BMP280/BMP380 pressure sensor I2C driver" depends on (I2C || SPI_MASTER) select REGMAP select BMP280_I2C if (I2C) select BMP280_SPI if (SPI_MASTER) help - Say yes here to build support for Bosch Sensortec BMP180 and BMP280 - pressure and temperature sensors. Also supports the BME280 with + Say yes here to build support for Bosch Sensortec BMP180, BMP280 and + BMP380 pressure and temperature sensors. Also supports the BME280 with an additional humidity sensor channel. To compile this driver as a module, choose M here: the core module diff --git a/drivers/iio/pressure/bmp280-core.c b/drivers/iio/pressure/bmp280-core.c index 9311eeec8473..f5b1344b8e20 100644 --- a/drivers/iio/pressure/bmp280-core.c +++ b/drivers/iio/pressure/bmp280-core.c @@ -12,10 +12,13 @@ * https://ae-bst.resource.bosch.com/media/_tech/media/datasheets/BST-BMP180-DS000-121.pdf * https://ae-bst.resource.bosch.com/media/_tech/media/datasheets/BST-BMP280-DS001-12.pdf * https://ae-bst.resource.bosch.com/media/_tech/media/datasheets/BST-BME280_DS001-11.pdf + * https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp388-ds001.pdf */ #define pr_fmt(fmt) "bmp280: " fmt +#include <linux/bitops.h> +#include <linux/bitfield.h> #include <linux/device.h> #include <linux/module.h> #include <linux/regmap.h> @@ -87,6 +90,24 @@ struct bmp280_calib { s8 H6; }; +/* See datasheet Section 3.11.1. */ +struct bmp380_calib { + u16 T1; + u16 T2; + s8 T3; + s16 P1; + s16 P2; + s8 P3; + s8 P4; + u16 P5; + u16 P6; + s8 P7; + s8 P8; + s16 P9; + s8 P10; + s8 P11; +}; + static const char *const bmp280_supply_names[] = { "vddd", "vdda" }; @@ -103,6 +124,7 @@ struct bmp280_data { union { struct bmp180_calib bmp180; struct bmp280_calib bmp280; + struct bmp380_calib bmp380; } calib; struct regulator_bulk_data supplies[BMP280_NUM_SUPPLIES]; unsigned int start_up_time; /* in microseconds */ @@ -167,6 +189,25 @@ enum { P9 = 16, }; +enum { + /* Temperature calib indexes */ + BMP380_T1 = 0, + BMP380_T2 = 2, + BMP380_T3 = 4, + /* Pressure calib indexes */ + BMP380_P1 = 5, + BMP380_P2 = 7, + BMP380_P3 = 9, + BMP380_P4 = 10, + BMP380_P5 = 11, + BMP380_P6 = 13, + BMP380_P7 = 15, + BMP380_P8 = 16, + BMP380_P9 = 17, + BMP380_P10 = 19, + BMP380_P11 = 20, +}; + static const struct iio_chan_spec bmp280_channels[] = { { .type = IIO_PRESSURE, @@ -742,6 +783,314 @@ static const struct bmp280_chip_info bme280_chip_info = { .read_calib = bmp280_read_calib, }; +/* Send a command to BMP3XX sensors */ +static int bmp380_cmd(struct bmp280_data *data, u8 cmd) +{ + int ret; + unsigned int reg; + + /* check if device is ready to process a command */ + ret = regmap_read(data->regmap, BMP380_REG_STATUS, &reg); + if (ret) { + dev_err(data->dev, "failed to read error register\n"); + return ret; + } + if (!(reg & BMP380_STATUS_CMD_RDY_MASK)) { + dev_err(data->dev, "device is not ready to accept commands\n"); + return -EBUSY; + } + + /* send command to process */ + ret = regmap_write(data->regmap, BMP380_REG_CMD, cmd); + if (ret) { + dev_err(data->dev, "failed to send command to device\n"); + return ret; + } + /* wait for 2ms for command to be proccessed */ + usleep_range(data->start_up_time, data->start_up_time + 100); + /* check for command processing error */ + ret = regmap_read(data->regmap, BMP380_REG_ERROR, &reg); + if (ret) { + dev_err(data->dev, "error reading ERROR reg\n"); + return ret; + } + if (reg & BMP380_ERR_CMD_MASK) { + dev_err(data->dev, "error processing command 0x%X\n", cmd); + return -EINVAL; + } + dev_dbg(data->dev, "Command 0x%X proccessed successfully\n", cmd); + + return 0; +} + +/* + * Returns temperature in DegC, resolution is 0.01 DegC. Output value of + * "5123" equals 51.23 DegC. t_fine carries fine temperature as global + * value. + * + * Taken from datasheet, Section Appendix 9, "Compensation formula" and repo + * https://github.com/BoschSensortec/BMP3-Sensor-API + */ +static s32 bmp380_compensate_temp(struct bmp280_data *data, u32 adc_temp) +{ + s64 var1, var2, var3, var4, var5, var6, comp_temp; + struct bmp380_calib *calib = &data->calib.bmp380; + + var1 = ((s64) adc_temp) - (((s64) calib->T1) << 8); + var2 = var1 * ((s64) calib->T2); + var3 = var1 * var1; + var4 = var3 * ((s64) calib->T3); + var5 = (var2 << 18) + var4; + var6 = var5 >> 32; + data->t_fine = (s32) var6; + comp_temp = (var6 * 25) >> 14; + + comp_temp = clamp_val(comp_temp, BMP380_MIN_TEMP, BMP380_MAX_TEMP); + return (s32) comp_temp; +} + +/* + * Returns pressure in Pa as unsigned 32 bit integer in fractional Pascal. + * Output value of "9528709" represents 9528709/100 = 95287.09 Pa = 952.8709 hPa + * + * Taken from datasheet, Section 9.3. "Pressure compensation" and repository + * https://github.com/BoschSensortec/BMP3-Sensor-API + */ +static u32 bmp380_compensate_press(struct bmp280_data *data, u32 adc_press) +{ + s64 var1, var2, var3, var4, var5, var6, offset, sensitivity; + u64 comp_press; + struct bmp380_calib *calib = &data->calib.bmp380; + + var1 = ((s64)data->t_fine) * ((s64)data->t_fine); + var2 = var1 >> 6; + var3 = (var2 * ((s64) data->t_fine)) >> 8; + var4 = (((s64)calib->P8) * var3) >> 5; + var5 = (((s64) calib->P7) * var1) << 4; + var6 = (((s64) calib->P6) * ((s64)data->t_fine)) << 22; + offset = (((s64)calib->P5) << 47) + var4 + var5 + var6; + var2 = (((s64)calib->P4) * var3) >> 5; + var4 = (((s64) calib->P3) * var1) << 2; + var5 = (((s64) calib->P2) - ((s64) 1<<14)) * + (((s64)data->t_fine) << 21); + sensitivity = ((((s64) calib->P1) - ((s64) 1 << 14)) << 46) + + var2 + var4 + var5; + var1 = (sensitivity >> 24) * ((s64)adc_press); + var2 = ((s64)calib->P10) * ((s64) data->t_fine); + var3 = var2 + (((s64) calib->P9) << 16); + var4 = (var3 * ((s64)adc_press)) >> 13; + + /* + * Dividing by 10 followed by multiplying by 10 to avoid + * possible overflow caused by (uncomp_data->pressure * partial_data4) + */ + var5 = (((s64)adc_press) * (var4 / 10)) >> 9; + var5 *= 10; + var6 = ((s64)adc_press) * ((s64)adc_press); + var2 = (((s64)calib->P11) * var6) >> 16; + var3 = (var2 * ((s64)adc_press)) >> 7; + var4 = (offset >> 2) + var1 + var5 + var3; + comp_press = ((u64)var4 * 25) >> 40; + + comp_press = clamp_val(comp_press, BMP380_MIN_PRES, BMP380_MAX_PRES); + return (u32)comp_press; +} + +static int bmp380_read_temp(struct bmp280_data *data, int *val) +{ + int ret; + u32 adc_temp; + s32 comp_temp; + + ret = regmap_bulk_read(data->regmap, BMP380_REG_TEMP_XLSB, data->buf, 3); + if (ret < 0) { + dev_err(data->dev, "failed to read temperature\n"); + return ret; + } + + adc_temp = get_unaligned_le24(data->buf); + if (adc_temp == BMP380_TEMP_SKIPPED) { + /* reading was skipped */ + dev_err(data->dev, "reading temperature skipped\n"); + return -EIO; + } + comp_temp = bmp380_compensate_temp(data, adc_temp); + + /* + * val might be NULL if we're called by the read_press routine, + * who only cares about the carry over t_fine value. + */ + if (val) { + /* IIO reports temperatures in mC */ + *val = comp_temp * 10; + return IIO_VAL_INT; + } + + return 0; +} + +static int bmp380_read_press(struct bmp280_data *data, int *val, int *val2) +{ + int ret; + u32 adc_press; + s32 comp_press; + + /* Read and compensate temperature so we get a reading of t_fine. */ + ret = bmp380_read_temp(data, NULL); + if (ret < 0) + return ret; + + ret = regmap_bulk_read(data->regmap, BMP380_REG_PRESS_XLSB, data->buf, 3); + if (ret < 0) { + dev_err(data->dev, "failed to read pressure\n"); + return ret; + } + + adc_press = get_unaligned_le24(data->buf); + if (adc_press == BMP380_PRESS_SKIPPED) { + /* reading was skipped */ + dev_err(data->dev, "reading pressure skipped\n"); + return -EIO; + } + comp_press = bmp380_compensate_press(data, adc_press); + + *val = comp_press; + /* Compensated pressure is in cPa (centipascals) */ + *val2 = 100000; + + return IIO_VAL_FRACTIONAL; +} + +static int bmp380_read_calib(struct bmp280_data *data, unsigned int chip) +{ + struct bmp380_calib *calib = &data->calib.bmp380; + int ret; + u8 *buf; + + buf = kmalloc(BMP380_CALIB_REG_COUNT, GFP_KERNEL); + if (!buf) + return -ENOMEM; + + /* Read temperature calibration values. */ + ret = regmap_bulk_read(data->regmap, BMP380_REG_CALIB_TEMP_START, buf, + BMP380_CALIB_REG_COUNT); + if (ret < 0) { + dev_err(data->dev, + "failed to read temperature calibration parameters\n"); + kfree(buf); + return ret; + } + + /* Toss the temperature calibration data into the entropy pool */ + add_device_randomness(buf, BMP380_CALIB_REG_COUNT); + + /* Parse calibration data */ + calib->T1 = get_unaligned_le16(&buf[BMP380_T1]); + calib->T2 = get_unaligned_le16(&buf[BMP380_T2]); + calib->T3 = buf[BMP380_T3]; + calib->P1 = get_unaligned_le16(&buf[BMP380_P1]); + calib->P2 = get_unaligned_le16(&buf[BMP380_P2]); + calib->P3 = buf[BMP380_P3]; + calib->P4 = buf[BMP380_P4]; + calib->P5 = get_unaligned_le16(&buf[BMP380_P5]); + calib->P6 = get_unaligned_le16(&buf[BMP380_P6]); + calib->P7 = buf[BMP380_P7]; + calib->P8 = buf[BMP380_P8]; + calib->P9 = get_unaligned_le16(&buf[BMP380_P9]); + calib->P10 = buf[BMP380_P10]; + calib->P11 = buf[BMP380_P11]; + + kfree(buf); + return 0; +} + +static int bmp380_chip_config(struct bmp280_data *data) +{ + unsigned int tmp; + u8 osrs; + int ret; + + /* configure power control register */ + ret = regmap_write_bits(data->regmap, BMP380_REG_POWER_CONTROL, + BMP380_CTRL_SENSORS_MASK | BMP380_MODE_MASK, + BMP380_CTRL_SENSORS_PRESS_EN | + BMP380_CTRL_SENSORS_TEMP_EN | + FIELD_PREP(BMP380_MODE_MASK, BMP380_MODE_NORMAL)); + if (ret < 0) { + dev_err(data->dev, + "failed to write operation control register\n"); + return ret; + } + + /* configure oversampling */ + osrs = FIELD_PREP(BMP380_OSRS_TEMP_MASK, data->oversampling_temp) | + FIELD_PREP(BMP380_OSRS_PRESS_MASK, data->oversampling_press); + + ret = regmap_write_bits(data->regmap, BMP380_REG_OSR, + BMP380_OSRS_TEMP_MASK | BMP380_OSRS_PRESS_MASK, + osrs); + if (ret < 0) { + dev_err(data->dev, "failed to write oversampling register\n"); + return ret; + } + + /* configure output data rate */ + ret = regmap_write_bits(data->regmap, BMP380_REG_ODR, + BMP380_ODRS_MASK, BMP380_ODRS_50HZ); + if (ret < 0) { + dev_err(data->dev, "failed to write ODR selection register\n"); + return ret; + } + + /* set filter data */ + ret = regmap_update_bits(data->regmap, BMP380_REG_CONFIG, + BMP380_FILTER_MASK, + FIELD_PREP(BMP380_FILTER_MASK, BMP380_FILTER_3X)); + if (ret < 0) { + dev_err(data->dev, "failed to write config register\n"); + return ret; + } + + /* wait startup_time before verifying config changes */ + usleep_range(data->start_up_time, data->start_up_time + 100); + + /* check config error flag */ + ret = regmap_read(data->regmap, BMP380_REG_ERROR, &tmp); + if (ret < 0) { + dev_err(data->dev, + "failed to read error register\n"); + return ret; + } + if (tmp & BMP380_ERR_CONF_MASK) { + dev_warn(data->dev, + "sensor flagged configuration as incompatible\n"); + return -EINVAL; + } + + return 0; +} + +static const int bmp380_oversampling_avail[] = { 1, 2, 4, 8, 16, 32 }; + +static const struct bmp280_chip_info bmp380_chip_info = { + .id_reg = BMP380_REG_ID, + .start_up_time = 2000, + .num_channels = 2, + + .oversampling_temp_avail = bmp380_oversampling_avail, + .num_oversampling_temp_avail = ARRAY_SIZE(bmp380_oversampling_avail), + .oversampling_temp_default = ilog2(1), + + .oversampling_press_avail = bmp380_oversampling_avail, + .num_oversampling_press_avail = ARRAY_SIZE(bmp380_oversampling_avail), + .oversampling_press_default = ilog2(4), + + .chip_config = bmp380_chip_config, + .read_temp = bmp380_read_temp, + .read_press = bmp380_read_press, + .read_calib = bmp380_read_calib, +}; + static int bmp180_measure(struct bmp280_data *data, u8 ctrl_meas) { int ret; @@ -1092,6 +1441,9 @@ int bmp280_common_probe(struct device *dev, case BME280_CHIP_ID: chip_info = &bme280_chip_info; break; + case BMP380_CHIP_ID: + chip_info = &bmp380_chip_info; + break; default: return -EINVAL; } @@ -1149,6 +1501,13 @@ int bmp280_common_probe(struct device *dev, return -EINVAL; } + /* BMP3xx requires soft-reset as part of initialization */ + if (chip_id == BMP380_CHIP_ID) { + ret = bmp380_cmd(data, BMP380_CMD_SOFT_RESET); + if (ret < 0) + return ret; + } + ret = data->chip_info->chip_config(data); if (ret < 0) return ret; diff --git a/drivers/iio/pressure/bmp280-i2c.c b/drivers/iio/pressure/bmp280-i2c.c index bf4a7a617537..744442dbe5f9 100644 --- a/drivers/iio/pressure/bmp280-i2c.c +++ b/drivers/iio/pressure/bmp280-i2c.c @@ -19,6 +19,9 @@ static int bmp280_i2c_probe(struct i2c_client *client, case BME280_CHIP_ID: regmap_config = &bmp280_regmap_config; break; + case BMP380_CHIP_ID: + regmap_config = &bmp380_regmap_config; + break; default: return -EINVAL; } @@ -37,6 +40,7 @@ static int bmp280_i2c_probe(struct i2c_client *client, } static const struct of_device_id bmp280_of_i2c_match[] = { + { .compatible = "bosch,bmp380", .data = (void *)BMP380_CHIP_ID }, { .compatible = "bosch,bme280", .data = (void *)BME280_CHIP_ID }, { .compatible = "bosch,bmp280", .data = (void *)BMP280_CHIP_ID }, { .compatible = "bosch,bmp180", .data = (void *)BMP180_CHIP_ID }, @@ -46,6 +50,7 @@ static const struct of_device_id bmp280_of_i2c_match[] = { MODULE_DEVICE_TABLE(of, bmp280_of_i2c_match); static const struct i2c_device_id bmp280_i2c_id[] = { + {"bmp380", BMP380_CHIP_ID }, {"bmp280", BMP280_CHIP_ID }, {"bmp180", BMP180_CHIP_ID }, {"bmp085", BMP180_CHIP_ID }, diff --git a/drivers/iio/pressure/bmp280-regmap.c b/drivers/iio/pressure/bmp280-regmap.c index 969698518984..c98c67970265 100644 --- a/drivers/iio/pressure/bmp280-regmap.c +++ b/drivers/iio/pressure/bmp280-regmap.c @@ -72,6 +72,49 @@ static bool bmp280_is_volatile_reg(struct device *dev, unsigned int reg) } } +static bool bmp380_is_writeable_reg(struct device *dev, unsigned int reg) +{ + switch (reg) { + case BMP380_REG_CMD: + case BMP380_REG_CONFIG: + case BMP380_REG_FIFO_CONFIG_1: + case BMP380_REG_FIFO_CONFIG_2: + case BMP380_REG_FIFO_WATERMARK_LSB: + case BMP380_REG_FIFO_WATERMARK_MSB: + case BMP380_REG_POWER_CONTROL: + case BMP380_REG_INT_CONTROL: + case BMP380_REG_IF_CONFIG: + case BMP380_REG_ODR: + case BMP380_REG_OSR: + return true; + default: + return false; + } +} + +static bool bmp380_is_volatile_reg(struct device *dev, unsigned int reg) +{ + switch (reg) { + case BMP380_REG_TEMP_XLSB: + case BMP380_REG_TEMP_LSB: + case BMP380_REG_TEMP_MSB: + case BMP380_REG_PRESS_XLSB: + case BMP380_REG_PRESS_LSB: + case BMP380_REG_PRESS_MSB: + case BMP380_REG_SENSOR_TIME_XLSB: + case BMP380_REG_SENSOR_TIME_LSB: + case BMP380_REG_SENSOR_TIME_MSB: + case BMP380_REG_INT_STATUS: + case BMP380_REG_FIFO_DATA: + case BMP380_REG_STATUS: + case BMP380_REG_ERROR: + case BMP380_REG_EVENT: + return true; + default: + return false; + } +} + const struct regmap_config bmp280_regmap_config = { .reg_bits = 8, .val_bits = 8, @@ -83,3 +126,15 @@ const struct regmap_config bmp280_regmap_config = { .volatile_reg = bmp280_is_volatile_reg, }; EXPORT_SYMBOL_NS(bmp280_regmap_config, IIO_BMP280); + +const struct regmap_config bmp380_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + + .max_register = BMP380_REG_CMD, + .cache_type = REGCACHE_RBTREE, + + .writeable_reg = bmp380_is_writeable_reg, + .volatile_reg = bmp380_is_volatile_reg, +}; +EXPORT_SYMBOL_NS(bmp380_regmap_config, IIO_BMP280); diff --git a/drivers/iio/pressure/bmp280-spi.c b/drivers/iio/pressure/bmp280-spi.c index 4cfaf3e869b8..011c68e07ebf 100644 --- a/drivers/iio/pressure/bmp280-spi.c +++ b/drivers/iio/pressure/bmp280-spi.c @@ -66,6 +66,9 @@ static int bmp280_spi_probe(struct spi_device *spi) case BME280_CHIP_ID: regmap_config = &bmp280_regmap_config; break; + case BMP380_CHIP_ID: + regmap_config = &bmp380_regmap_config; + break; default: return -EINVAL; } @@ -92,6 +95,7 @@ static const struct of_device_id bmp280_of_spi_match[] = { { .compatible = "bosch,bmp181", }, { .compatible = "bosch,bmp280", }, { .compatible = "bosch,bme280", }, + { .compatible = "bosch,bmp380", }, { }, }; MODULE_DEVICE_TABLE(of, bmp280_of_spi_match); @@ -101,6 +105,7 @@ static const struct spi_device_id bmp280_spi_id[] = { { "bmp181", BMP180_CHIP_ID }, { "bmp280", BMP280_CHIP_ID }, { "bme280", BME280_CHIP_ID }, + { "bmp380", BMP380_CHIP_ID }, { } }; MODULE_DEVICE_TABLE(spi, bmp280_spi_id); diff --git a/drivers/iio/pressure/bmp280.h b/drivers/iio/pressure/bmp280.h index 57ba0e85db91..fd38906c889c 100644 --- a/drivers/iio/pressure/bmp280.h +++ b/drivers/iio/pressure/bmp280.h @@ -3,6 +3,105 @@ #include <linux/device.h> #include <linux/regmap.h> +/* BMP380 specific registers */ +#define BMP380_REG_CMD 0x7E +#define BMP380_REG_CONFIG 0x1F +#define BMP380_REG_ODR 0X1D +#define BMP380_REG_OSR 0X1C +#define BMP380_REG_POWER_CONTROL 0X1B +#define BMP380_REG_IF_CONFIG 0X1A +#define BMP380_REG_INT_CONTROL 0X19 +#define BMP380_REG_INT_STATUS 0X11 +#define BMP380_REG_EVENT 0X10 +#define BMP380_REG_STATUS 0X03 +#define BMP380_REG_ERROR 0X02 +#define BMP380_REG_ID 0X00 + +#define BMP380_REG_FIFO_CONFIG_1 0X18 +#define BMP380_REG_FIFO_CONFIG_2 0X17 +#define BMP380_REG_FIFO_WATERMARK_MSB 0X16 +#define BMP380_REG_FIFO_WATERMARK_LSB 0X15 +#define BMP380_REG_FIFO_DATA 0X14 +#define BMP380_REG_FIFO_LENGTH_MSB 0X13 +#define BMP380_REG_FIFO_LENGTH_LSB 0X12 + +#define BMP380_REG_SENSOR_TIME_MSB 0X0E +#define BMP380_REG_SENSOR_TIME_LSB 0X0D +#define BMP380_REG_SENSOR_TIME_XLSB 0X0C + +#define BMP380_REG_TEMP_MSB 0X09 +#define BMP380_REG_TEMP_LSB 0X08 +#define BMP380_REG_TEMP_XLSB 0X07 + +#define BMP380_REG_PRESS_MSB 0X06 +#define BMP380_REG_PRESS_LSB 0X05 +#define BMP380_REG_PRESS_XLSB 0X04 + +#define BMP380_REG_CALIB_TEMP_START 0x31 +#define BMP380_CALIB_REG_COUNT 21 + +#define BMP380_FILTER_MASK GENMASK(3, 1) +#define BMP380_FILTER_OFF 0 +#define BMP380_FILTER_1X 1 +#define BMP380_FILTER_3X 2 +#define BMP380_FILTER_7X 3 +#define BMP380_FILTER_15X 4 +#define BMP380_FILTER_31X 5 +#define BMP380_FILTER_63X 6 +#define BMP380_FILTER_127X 7 + +#define BMP380_OSRS_TEMP_MASK GENMASK(5, 3) +#define BMP380_OSRS_PRESS_MASK GENMASK(2, 0) + +#define BMP380_ODRS_MASK GENMASK(4, 0) +#define BMP380_ODRS_200HZ 0x00 +#define BMP380_ODRS_100HZ 0x01 +#define BMP380_ODRS_50HZ 0x02 +#define BMP380_ODRS_25HZ 0x03 +#define BMP380_ODRS_12_5HZ 0x04 +#define BMP380_ODRS_6_25HZ 0x05 +#define BMP380_ODRS_3_1HZ 0x06 +#define BMP380_ODRS_1_5HZ 0x07 +#define BMP380_ODRS_0_78HZ 0x08 +#define BMP380_ODRS_0_39HZ 0x09 +#define BMP380_ODRS_0_2HZ 0x0A +#define BMP380_ODRS_0_1HZ 0x0B +#define BMP380_ODRS_0_05HZ 0x0C +#define BMP380_ODRS_0_02HZ 0x0D +#define BMP380_ODRS_0_01HZ 0x0E +#define BMP380_ODRS_0_006HZ 0x0F +#define BMP380_ODRS_0_003HZ 0x10 +#define BMP380_ODRS_0_0015HZ 0x11 + +#define BMP380_CTRL_SENSORS_MASK GENMASK(1, 0) +#define BMP380_CTRL_SENSORS_PRESS_EN BIT(0) +#define BMP380_CTRL_SENSORS_TEMP_EN BIT(1) +#define BMP380_MODE_MASK GENMASK(5, 4) +#define BMP380_MODE_SLEEP 0 +#define BMP380_MODE_FORCED 1 +#define BMP380_MODE_NORMAL 3 + +#define BMP380_MIN_TEMP -4000 +#define BMP380_MAX_TEMP 8500 +#define BMP380_MIN_PRES 3000000 +#define BMP380_MAX_PRES 12500000 + +#define BMP380_CMD_NOOP 0X00 +#define BMP380_CMD_EXTMODE_EN_MID 0x34 +#define BMP380_CMD_FIFO_FLUSH 0XB0 +#define BMP380_CMD_SOFT_RESET 0xB6 + +#define BMP380_STATUS_CMD_RDY_MASK BIT(4) +#define BMP380_STATUS_DRDY_PRESS_MASK BIT(5) +#define BMP380_STATUS_DRDY_TEMP_MASK BIT(6) + +#define BMP380_ERR_FATAL_MASK BIT(0) +#define BMP380_ERR_CMD_MASK BIT(1) +#define BMP380_ERR_CONF_MASK BIT(2) + +#define BMP380_TEMP_SKIPPED 0x800000 +#define BMP380_PRESS_SKIPPED 0x800000 + /* BMP280 specific registers */ #define BMP280_REG_HUMIDITY_LSB 0xFE #define BMP280_REG_HUMIDITY_MSB 0xFD @@ -92,6 +191,7 @@ #define BMP280_REG_RESET 0xE0 #define BMP280_REG_ID 0xD0 +#define BMP380_CHIP_ID 0x50 #define BMP180_CHIP_ID 0x55 #define BMP280_CHIP_ID 0x58 #define BME280_CHIP_ID 0x60 @@ -105,6 +205,7 @@ /* Regmap configurations */ extern const struct regmap_config bmp180_regmap_config; extern const struct regmap_config bmp280_regmap_config; +extern const struct regmap_config bmp380_regmap_config; /* Probe called from different transports */ int bmp280_common_probe(struct device *dev,

[v4,4/5] iio: pressure: bmp280: Add support for BMP380 sensor family

Commit Message

Comments

Patch