| Message ID | 20220727164646.387541-3-krzysztof.kozlowski@linaro.org (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
| Series | dt-bindings: iio: use spi-peripheral-props.yaml | expand |
On Wed, 27 Jul 2022 18:46:38 +0200 Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > Instead of listing directly properties typical for SPI peripherals, > reference the spi-peripheral-props.yaml schema. This allows using all > properties typical for SPI-connected devices, even these which device > bindings author did not tried yet. > > Remove the spi-* properties which now come via spi-peripheral-props.yaml > schema, except for the cases when device schema adds some constraints > like maximum frequency. > > While changing additionalProperties->unevaluatedProperties, put it in > typical place, just before example DTS. > > Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > > --- > > I wonder if spi-3wire is device specific (not controller) and should be > rather explicitly mentioned by device schema. Just like spi-cpol/cpha. I think it is, but Mark is expert on this. In general I'm waiting on Mark's opinion on the whole idea! Thanks, Jonathan > --- > .../devicetree/bindings/iio/accel/adi,adis16201.yaml | 7 ++++--- > .../devicetree/bindings/iio/accel/adi,adis16240.yaml | 7 ++++--- > .../devicetree/bindings/iio/accel/adi,adxl313.yaml | 9 ++++----- > .../devicetree/bindings/iio/accel/adi,adxl345.yaml | 7 ++++--- > .../devicetree/bindings/iio/accel/adi,adxl355.yaml | 7 ++++--- > .../devicetree/bindings/iio/accel/adi,adxl367.yaml | 7 ++++--- > .../devicetree/bindings/iio/accel/adi,adxl372.yaml | 7 ++++--- > .../devicetree/bindings/iio/accel/bosch,bma220.yaml | 7 ++++--- > .../devicetree/bindings/iio/accel/bosch,bma255.yaml | 5 ++++- > .../devicetree/bindings/iio/accel/bosch,bmi088.yaml | 7 ++++--- > .../devicetree/bindings/iio/accel/fsl,mma7455.yaml | 7 ++++--- > .../devicetree/bindings/iio/accel/kionix,kxsd9.yaml | 7 ++++--- > .../devicetree/bindings/iio/accel/murata,sca3300.yaml | 5 ++++- > .../devicetree/bindings/iio/accel/nxp,fxls8962af.yaml | 7 ++++--- > 14 files changed, 56 insertions(+), 40 deletions(-) > > diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adis16201.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adis16201.yaml > index 6f8f8a6258fe..7332442e5661 100644 > --- a/Documentation/devicetree/bindings/iio/accel/adi,adis16201.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/adi,adis16201.yaml > @@ -27,15 +27,16 @@ properties: > interrupts: > maxItems: 1 > > - spi-max-frequency: true > - > vdd-supply: true > > required: > - compatible > - reg > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml > index 8d829ef878bc..f6f97164c2ca 100644 > --- a/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml > @@ -25,14 +25,15 @@ properties: > interrupts: > maxItems: 1 > > - spi-max-frequency: true > - > required: > - compatible > - reg > - interrupts > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml > index d6afc1b8c272..7c1bc7810528 100644 > --- a/Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml > @@ -22,10 +22,6 @@ properties: > reg: > maxItems: 1 > > - spi-3wire: true > - > - spi-max-frequency: true > - > vs-supply: > description: Regulator that supplies power to the accelerometer > > @@ -48,7 +44,10 @@ required: > - compatible > - reg > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl345.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl345.yaml > index 9bb039e2f533..346abfb13a3a 100644 > --- a/Documentation/devicetree/bindings/iio/accel/adi,adxl345.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl345.yaml > @@ -32,8 +32,6 @@ properties: > > spi-cpol: true > > - spi-max-frequency: true > - > interrupts: > maxItems: 1 > > @@ -42,7 +40,10 @@ required: > - reg > - interrupts > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml > index ba54d6998f2e..14b487088ab4 100644 > --- a/Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml > @@ -45,13 +45,14 @@ properties: > vddio-supply: > description: Regulator that provides power to the bus > > - spi-max-frequency: true > - > required: > - compatible > - reg > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl367.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl367.yaml > index d259e796c1d6..f10d98d34cb8 100644 > --- a/Documentation/devicetree/bindings/iio/accel/adi,adxl367.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl367.yaml > @@ -35,8 +35,6 @@ properties: > interrupts: > maxItems: 1 > > - spi-max-frequency: true > - > vdd-supply: true > vddio-supply: true > > @@ -45,7 +43,10 @@ required: > - reg > - interrupts > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl372.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl372.yaml > index 38b59b6454ce..73a5c8f814cc 100644 > --- a/Documentation/devicetree/bindings/iio/accel/adi,adxl372.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl372.yaml > @@ -25,14 +25,15 @@ properties: > interrupts: > maxItems: 1 > > - spi-max-frequency: true > - > required: > - compatible > - reg > - interrupts > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/bosch,bma220.yaml b/Documentation/devicetree/bindings/iio/accel/bosch,bma220.yaml > index 942b23ad0712..5dd06f5905b4 100644 > --- a/Documentation/devicetree/bindings/iio/accel/bosch,bma220.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/bosch,bma220.yaml > @@ -20,8 +20,6 @@ properties: > interrupts: > maxItems: 1 > > - spi-max-frequency: true > - > vdda-supply: true > vddd-supply: true > vddio-supply: true > @@ -30,7 +28,10 @@ required: > - compatible > - reg > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/bosch,bma255.yaml b/Documentation/devicetree/bindings/iio/accel/bosch,bma255.yaml > index 478e75ae0885..457a709b583c 100644 > --- a/Documentation/devicetree/bindings/iio/accel/bosch,bma255.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/bosch,bma255.yaml > @@ -72,7 +72,10 @@ required: > - compatible > - reg > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/bosch,bmi088.yaml b/Documentation/devicetree/bindings/iio/accel/bosch,bmi088.yaml > index 272eb48eef5a..3cb82576d758 100644 > --- a/Documentation/devicetree/bindings/iio/accel/bosch,bmi088.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/bosch,bmi088.yaml > @@ -24,8 +24,6 @@ properties: > reg: > maxItems: 1 > > - spi-max-frequency: true > - > vdd-supply: true > > vddio-supply: true > @@ -50,7 +48,10 @@ required: > - compatible > - reg > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/fsl,mma7455.yaml b/Documentation/devicetree/bindings/iio/accel/fsl,mma7455.yaml > index 7c8f8bdc2333..589ca8178f4a 100644 > --- a/Documentation/devicetree/bindings/iio/accel/fsl,mma7455.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/fsl,mma7455.yaml > @@ -40,13 +40,14 @@ properties: > - "INT1" > - "INT2" > > - spi-max-frequency: true > - > required: > - compatible > - reg > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.yaml b/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.yaml > index 390b87242fcb..f64d99b35492 100644 > --- a/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.yaml > @@ -29,13 +29,14 @@ properties: > mount-matrix: > description: an optional 3x3 mounting rotation matrix. > > - spi-max-frequency: true > - > required: > - compatible > - reg > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/murata,sca3300.yaml b/Documentation/devicetree/bindings/iio/accel/murata,sca3300.yaml > index f6e2a16a710b..00c990caa1e4 100644 > --- a/Documentation/devicetree/bindings/iio/accel/murata,sca3300.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/murata,sca3300.yaml > @@ -29,7 +29,10 @@ required: > - compatible > - reg > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - | > diff --git a/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml b/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml > index ad529ab2c6e2..65ce8ea14b52 100644 > --- a/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml > +++ b/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml > @@ -27,8 +27,6 @@ properties: > vdd-supply: > description: phandle to the regulator that provides power to the accelerometer > > - spi-max-frequency: true > - > interrupts: > maxItems: 1 > > @@ -44,7 +42,10 @@ required: > - compatible > - reg > > -additionalProperties: false > +allOf: > + - $ref: /schemas/spi/spi-peripheral-props.yaml# > + > +unevaluatedProperties: false > > examples: > - |
On Sun, Jul 31, 2022 at 04:49:43PM +0100, Jonathan Cameron wrote: > On Wed, 27 Jul 2022 18:46:38 +0200 > Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > > Instead of listing directly properties typical for SPI peripherals, > > reference the spi-peripheral-props.yaml schema. This allows using all > > properties typical for SPI-connected devices, even these which device > > bindings author did not tried yet. > > > > Remove the spi-* properties which now come via spi-peripheral-props.yaml > > schema, except for the cases when device schema adds some constraints > > like maximum frequency. > > > > While changing additionalProperties->unevaluatedProperties, put it in > > typical place, just before example DTS. > > > > Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > > > > --- > > > > I wonder if spi-3wire is device specific (not controller) and should be > > rather explicitly mentioned by device schema. Just like spi-cpol/cpha. > > I think it is, but Mark is expert on this. I would say yes as it's the device with a single data line. > In general I'm waiting on Mark's opinion on the whole idea! The prerequisite changes (except for spi-3-wire) are already queued up by Mark as are changes for other subsystems. Rob
On 03/08/2022 23:29, Rob Herring wrote: >>> I wonder if spi-3wire is device specific (not controller) and should be >>> rather explicitly mentioned by device schema. Just like spi-cpol/cpha. >> >> I think it is, but Mark is expert on this. > > I would say yes as it's the device with a single data line. I will move it to device schema, just like cpol/cpha, and send a v3. After the merge window. > >> In general I'm waiting on Mark's opinion on the whole idea! > > The prerequisite changes (except for spi-3-wire) are already queued up > by Mark as are changes for other subsystems. Best regards, Krzysztof
On Thu, 4 Aug 2022 09:27:37 +0200 Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > On 03/08/2022 23:29, Rob Herring wrote: > >>> I wonder if spi-3wire is device specific (not controller) and should be > >>> rather explicitly mentioned by device schema. Just like spi-cpol/cpha. > >> > >> I think it is, but Mark is expert on this. > > > > I would say yes as it's the device with a single data line. > > I will move it to device schema, just like cpol/cpha, and send a v3. > After the merge window. Works for me. I'll wait for v3 then. > > > > >> In general I'm waiting on Mark's opinion on the whole idea! > > > > The prerequisite changes (except for spi-3-wire) are already queued up > > by Mark as are changes for other subsystems. Ah. Got it. Thanks for driving this through. Jonathan > > > Best regards, > Krzysztof
diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adis16201.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adis16201.yaml index 6f8f8a6258fe..7332442e5661 100644 --- a/Documentation/devicetree/bindings/iio/accel/adi,adis16201.yaml +++ b/Documentation/devicetree/bindings/iio/accel/adi,adis16201.yaml @@ -27,15 +27,16 @@ properties: interrupts: maxItems: 1 - spi-max-frequency: true - vdd-supply: true required: - compatible - reg -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml index 8d829ef878bc..f6f97164c2ca 100644 --- a/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml +++ b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml @@ -25,14 +25,15 @@ properties: interrupts: maxItems: 1 - spi-max-frequency: true - required: - compatible - reg - interrupts -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml index d6afc1b8c272..7c1bc7810528 100644 --- a/Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml @@ -22,10 +22,6 @@ properties: reg: maxItems: 1 - spi-3wire: true - - spi-max-frequency: true - vs-supply: description: Regulator that supplies power to the accelerometer @@ -48,7 +44,10 @@ required: - compatible - reg -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl345.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl345.yaml index 9bb039e2f533..346abfb13a3a 100644 --- a/Documentation/devicetree/bindings/iio/accel/adi,adxl345.yaml +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl345.yaml @@ -32,8 +32,6 @@ properties: spi-cpol: true - spi-max-frequency: true - interrupts: maxItems: 1 @@ -42,7 +40,10 @@ required: - reg - interrupts -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml index ba54d6998f2e..14b487088ab4 100644 --- a/Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml @@ -45,13 +45,14 @@ properties: vddio-supply: description: Regulator that provides power to the bus - spi-max-frequency: true - required: - compatible - reg -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl367.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl367.yaml index d259e796c1d6..f10d98d34cb8 100644 --- a/Documentation/devicetree/bindings/iio/accel/adi,adxl367.yaml +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl367.yaml @@ -35,8 +35,6 @@ properties: interrupts: maxItems: 1 - spi-max-frequency: true - vdd-supply: true vddio-supply: true @@ -45,7 +43,10 @@ required: - reg - interrupts -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl372.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl372.yaml index 38b59b6454ce..73a5c8f814cc 100644 --- a/Documentation/devicetree/bindings/iio/accel/adi,adxl372.yaml +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl372.yaml @@ -25,14 +25,15 @@ properties: interrupts: maxItems: 1 - spi-max-frequency: true - required: - compatible - reg - interrupts -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/bosch,bma220.yaml b/Documentation/devicetree/bindings/iio/accel/bosch,bma220.yaml index 942b23ad0712..5dd06f5905b4 100644 --- a/Documentation/devicetree/bindings/iio/accel/bosch,bma220.yaml +++ b/Documentation/devicetree/bindings/iio/accel/bosch,bma220.yaml @@ -20,8 +20,6 @@ properties: interrupts: maxItems: 1 - spi-max-frequency: true - vdda-supply: true vddd-supply: true vddio-supply: true @@ -30,7 +28,10 @@ required: - compatible - reg -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/bosch,bma255.yaml b/Documentation/devicetree/bindings/iio/accel/bosch,bma255.yaml index 478e75ae0885..457a709b583c 100644 --- a/Documentation/devicetree/bindings/iio/accel/bosch,bma255.yaml +++ b/Documentation/devicetree/bindings/iio/accel/bosch,bma255.yaml @@ -72,7 +72,10 @@ required: - compatible - reg -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/bosch,bmi088.yaml b/Documentation/devicetree/bindings/iio/accel/bosch,bmi088.yaml index 272eb48eef5a..3cb82576d758 100644 --- a/Documentation/devicetree/bindings/iio/accel/bosch,bmi088.yaml +++ b/Documentation/devicetree/bindings/iio/accel/bosch,bmi088.yaml @@ -24,8 +24,6 @@ properties: reg: maxItems: 1 - spi-max-frequency: true - vdd-supply: true vddio-supply: true @@ -50,7 +48,10 @@ required: - compatible - reg -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/fsl,mma7455.yaml b/Documentation/devicetree/bindings/iio/accel/fsl,mma7455.yaml index 7c8f8bdc2333..589ca8178f4a 100644 --- a/Documentation/devicetree/bindings/iio/accel/fsl,mma7455.yaml +++ b/Documentation/devicetree/bindings/iio/accel/fsl,mma7455.yaml @@ -40,13 +40,14 @@ properties: - "INT1" - "INT2" - spi-max-frequency: true - required: - compatible - reg -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.yaml b/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.yaml index 390b87242fcb..f64d99b35492 100644 --- a/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.yaml +++ b/Documentation/devicetree/bindings/iio/accel/kionix,kxsd9.yaml @@ -29,13 +29,14 @@ properties: mount-matrix: description: an optional 3x3 mounting rotation matrix. - spi-max-frequency: true - required: - compatible - reg -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/murata,sca3300.yaml b/Documentation/devicetree/bindings/iio/accel/murata,sca3300.yaml index f6e2a16a710b..00c990caa1e4 100644 --- a/Documentation/devicetree/bindings/iio/accel/murata,sca3300.yaml +++ b/Documentation/devicetree/bindings/iio/accel/murata,sca3300.yaml @@ -29,7 +29,10 @@ required: - compatible - reg -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml b/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml index ad529ab2c6e2..65ce8ea14b52 100644 --- a/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml +++ b/Documentation/devicetree/bindings/iio/accel/nxp,fxls8962af.yaml @@ -27,8 +27,6 @@ properties: vdd-supply: description: phandle to the regulator that provides power to the accelerometer - spi-max-frequency: true - interrupts: maxItems: 1 @@ -44,7 +42,10 @@ required: - compatible - reg -additionalProperties: false +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false examples: - |
Instead of listing directly properties typical for SPI peripherals, reference the spi-peripheral-props.yaml schema. This allows using all properties typical for SPI-connected devices, even these which device bindings author did not tried yet. Remove the spi-* properties which now come via spi-peripheral-props.yaml schema, except for the cases when device schema adds some constraints like maximum frequency. While changing additionalProperties->unevaluatedProperties, put it in typical place, just before example DTS. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- I wonder if spi-3wire is device specific (not controller) and should be rather explicitly mentioned by device schema. Just like spi-cpol/cpha. --- .../devicetree/bindings/iio/accel/adi,adis16201.yaml | 7 ++++--- .../devicetree/bindings/iio/accel/adi,adis16240.yaml | 7 ++++--- .../devicetree/bindings/iio/accel/adi,adxl313.yaml | 9 ++++----- .../devicetree/bindings/iio/accel/adi,adxl345.yaml | 7 ++++--- .../devicetree/bindings/iio/accel/adi,adxl355.yaml | 7 ++++--- .../devicetree/bindings/iio/accel/adi,adxl367.yaml | 7 ++++--- .../devicetree/bindings/iio/accel/adi,adxl372.yaml | 7 ++++--- .../devicetree/bindings/iio/accel/bosch,bma220.yaml | 7 ++++--- .../devicetree/bindings/iio/accel/bosch,bma255.yaml | 5 ++++- .../devicetree/bindings/iio/accel/bosch,bmi088.yaml | 7 ++++--- .../devicetree/bindings/iio/accel/fsl,mma7455.yaml | 7 ++++--- .../devicetree/bindings/iio/accel/kionix,kxsd9.yaml | 7 ++++--- .../devicetree/bindings/iio/accel/murata,sca3300.yaml | 5 ++++- .../devicetree/bindings/iio/accel/nxp,fxls8962af.yaml | 7 ++++--- 14 files changed, 56 insertions(+), 40 deletions(-)