@@ -310,7 +310,8 @@ i915-y += i915_perf.o
# Protected execution platform (PXP) support. Base support is required for HuC
i915-y += \
pxp/intel_pxp.o \
- pxp/intel_pxp_tee.o
+ pxp/intel_pxp_tee.o \
+ pxp/intel_pxp_huc.o
i915-$(CONFIG_DRM_I915_PXP) += \
pxp/intel_pxp_cmd.o \
new file mode 100644
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: MIT
+/*
+ * Copyright(c) 2021, Intel Corporation. All rights reserved.
+ */
+
+#include "drm/i915_drm.h"
+#include "i915_drv.h"
+
+#include "gem/i915_gem_region.h"
+#include "gt/intel_gt.h"
+
+#include "intel_pxp.h"
+#include "intel_pxp_huc.h"
+#include "intel_pxp_tee.h"
+#include "intel_pxp_types.h"
+#include "intel_pxp_tee_interface.h"
+
+int intel_pxp_huc_load_and_auth(struct intel_pxp *pxp)
+{
+ struct intel_gt *gt = pxp_to_gt(pxp);
+ struct intel_huc *huc = >->uc.huc;
+ struct pxp_tee_start_huc_auth_in huc_in = {0};
+ struct pxp_tee_start_huc_auth_out huc_out = {0};
+ dma_addr_t huc_phys_addr;
+ u8 client_id = 0;
+ u8 fence_id = 0;
+ int err;
+
+ if (!pxp->pxp_component)
+ return -ENODEV;
+
+ huc_phys_addr = i915_gem_object_get_dma_address(huc->fw.obj, 0);
+
+ /* write the PXP message into the lmem (the sg list) */
+ huc_in.header.api_version = PXP_TEE_43_APIVER;
+ huc_in.header.command_id = PXP_TEE_43_START_HUC_AUTH;
+ huc_in.header.status = 0;
+ huc_in.header.buffer_len = sizeof(huc_in.huc_base_address);
+ huc_in.huc_base_address = huc_phys_addr;
+
+ err = intel_pxp_tee_stream_message(pxp, client_id, fence_id,
+ &huc_in, sizeof(huc_in),
+ &huc_out, sizeof(huc_out));
+ if (err < 0) {
+ drm_err(>->i915->drm,
+ "Failed to send HuC load and auth command to GSC [%d]!\n",
+ err);
+ return err;
+ }
+
+ /*
+ * HuC does sometimes survive suspend/resume (it depends on how "deep"
+ * a sleep state the device reaches) so we can end up here on resume
+ * with HuC already loaded, in which case the GSC will return
+ * PXP_STATUS_OP_NOT_PERMITTED. We can therefore consider the GuC
+ * correctly transferred in this scenario; if the same error is ever
+ * returned with HuC not loaded we'll still catch it when we check the
+ * authentication bit later.
+ */
+ if (huc_out.header.status != PXP_STATUS_SUCCESS &&
+ huc_out.header.status != PXP_STATUS_OP_NOT_PERMITTED) {
+ drm_err(>->i915->drm,
+ "HuC load failed with GSC error = 0x%x\n",
+ huc_out.header.status);
+ return -EPROTO;
+ }
+
+ return 0;
+}
new file mode 100644
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: MIT */
+/*
+ * Copyright(c) 2021, Intel Corporation. All rights reserved.
+ */
+
+#ifndef __INTEL_PXP_HUC_H__
+#define __INTEL_PXP_HUC_H__
+
+#include <linux/types.h>
+
+struct intel_pxp;
+
+int intel_pxp_huc_load_and_auth(struct intel_pxp *pxp);
+
+#endif /* __INTEL_PXP_HUC_H__ */
@@ -9,8 +9,20 @@
#include <linux/types.h>
#define PXP_TEE_APIVER 0x40002
+#define PXP_TEE_43_APIVER 0x00040003
#define PXP_TEE_ARB_CMDID 0x1e
#define PXP_TEE_ARB_PROTECTION_MODE 0x2
+#define PXP_TEE_43_START_HUC_AUTH 0x0000003A
+
+/*
+ * there are a lot of status codes for PXP, but we only define the ones we
+ * actually can handle in the driver. other failure codes will be printed to
+ * error msg for debug.
+ */
+enum pxp_status {
+ PXP_STATUS_SUCCESS = 0x0,
+ PXP_STATUS_OP_NOT_PERMITTED = 0x4013
+};
/* PXP TEE message header */
struct pxp_tee_cmd_header {
@@ -33,4 +45,13 @@ struct pxp_tee_create_arb_out {
struct pxp_tee_cmd_header header;
} __packed;
+struct pxp_tee_start_huc_auth_in {
+ struct pxp_tee_cmd_header header;
+ __le64 huc_base_address;
+};
+
+struct pxp_tee_start_huc_auth_out {
+ struct pxp_tee_cmd_header header;
+};
+
#endif /* __INTEL_PXP_TEE_INTERFACE_H__ */