@@ -92,6 +92,15 @@
#define KSZ9x31_LMD_VCT_DATA_HI_PULSE_MASK GENMASK(1, 0)
#define KSZ9x31_LMD_VCT_DATA_MASK GENMASK(7, 0)
+#define KSZPHY_WIRE_PAIR_MASK 0x3
+
+#define LAN8814_CABLE_DIAG 0x12
+#define LAN8814_CABLE_DIAG_STAT_MASK GENMASK(9, 8)
+#define LAN8814_CABLE_DIAG_VCT_DATA_MASK GENMASK(7, 0)
+#define LAN8814_PAIR_BIT_SHIFT 12
+
+#define LAN8814_WIRE_PAIR_MASK 0xF
+
/* Lan8814 general Interrupt control/status reg in GPHY specific block. */
#define LAN8814_INTC 0x18
#define LAN8814_INTS 0x1B
@@ -257,6 +266,8 @@ static struct kszphy_hw_stat kszphy_hw_stats[] = {
struct kszphy_type {
u32 led_mode_reg;
u16 interrupt_level_mask;
+ u16 cable_diag_reg;
+ unsigned long pair_mask;
bool has_broadcast_disable;
bool has_nand_tree_disable;
bool has_rmii_ref_clk_sel;
@@ -313,6 +324,13 @@ struct kszphy_priv {
static const struct kszphy_type lan8814_type = {
.led_mode_reg = ~LAN8814_LED_CTRL_1,
+ .cable_diag_reg = LAN8814_CABLE_DIAG,
+ .pair_mask = LAN8814_WIRE_PAIR_MASK,
+};
+
+static const struct kszphy_type ksz886x_type = {
+ .cable_diag_reg = KSZ8081_LMD,
+ .pair_mask = KSZPHY_WIRE_PAIR_MASK,
};
static const struct kszphy_type ksz8021_type = {
@@ -1796,6 +1814,17 @@ static int kszphy_probe(struct phy_device *phydev)
return 0;
}
+static int lan8814_cable_test_start(struct phy_device *phydev)
+{
+ /* If autoneg is enabled, we won't be able to test cross pair
+ * short. In this case, the PHY will "detect" a link and
+ * confuse the internal state machine - disable auto neg here.
+ * Set the speed to 1000mbit and full duplex.
+ */
+ return phy_modify(phydev, MII_BMCR, BMCR_ANENABLE | BMCR_SPEED100,
+ BMCR_SPEED1000 | BMCR_FULLDPLX);
+}
+
static int ksz886x_cable_test_start(struct phy_device *phydev)
{
if (phydev->dev_flags & MICREL_KSZ8_P1_ERRATA)
@@ -1809,9 +1838,9 @@ static int ksz886x_cable_test_start(struct phy_device *phydev)
return phy_clear_bits(phydev, MII_BMCR, BMCR_ANENABLE | BMCR_SPEED100);
}
-static int ksz886x_cable_test_result_trans(u16 status)
+static int ksz886x_cable_test_result_trans(u16 status, u16 mask)
{
- switch (FIELD_GET(KSZ8081_LMD_STAT_MASK, status)) {
+ switch (FIELD_GET(mask, status)) {
case KSZ8081_LMD_STAT_NORMAL:
return ETHTOOL_A_CABLE_RESULT_CODE_OK;
case KSZ8081_LMD_STAT_SHORT:
@@ -1825,15 +1854,15 @@ static int ksz886x_cable_test_result_trans(u16 status)
}
}
-static bool ksz886x_cable_test_failed(u16 status)
+static bool ksz886x_cable_test_failed(u16 status, u16 mask)
{
- return FIELD_GET(KSZ8081_LMD_STAT_MASK, status) ==
+ return FIELD_GET(mask, status) ==
KSZ8081_LMD_STAT_FAIL;
}
-static bool ksz886x_cable_test_fault_length_valid(u16 status)
+static bool ksz886x_cable_test_fault_length_valid(u16 status, u16 mask)
{
- switch (FIELD_GET(KSZ8081_LMD_STAT_MASK, status)) {
+ switch (FIELD_GET(mask, status)) {
case KSZ8081_LMD_STAT_OPEN:
fallthrough;
case KSZ8081_LMD_STAT_SHORT:
@@ -1842,29 +1871,79 @@ static bool ksz886x_cable_test_fault_length_valid(u16 status)
return false;
}
-static int ksz886x_cable_test_fault_length(u16 status)
+static int ksz886x_cable_test_fault_length(struct phy_device *phydev, u16 status, u16 data_mask)
{
int dt;
/* According to the data sheet the distance to the fault is
- * DELTA_TIME * 0.4 meters.
+ * DELTA_TIME * 0.4 meters for ksz phys.
+ * (DELTA_TIME - 22) * 0.8 for lan8814 phy.
*/
- dt = FIELD_GET(KSZ8081_LMD_DELTA_TIME_MASK, status);
+ dt = FIELD_GET(data_mask, status);
- return (dt * 400) / 10;
+ if ((phydev->phy_id & MICREL_PHY_ID_MASK) == PHY_ID_LAN8814)
+ return ((dt - 22) * 800) / 10;
+ else
+ return (dt * 400) / 10;
}
static int ksz886x_cable_test_wait_for_completion(struct phy_device *phydev)
{
+ const struct kszphy_type *type = phydev->drv->driver_data;
int val, ret;
- ret = phy_read_poll_timeout(phydev, KSZ8081_LMD, val,
+ ret = phy_read_poll_timeout(phydev, type->cable_diag_reg, val,
!(val & KSZ8081_LMD_ENABLE_TEST),
30000, 100000, true);
return ret < 0 ? ret : 0;
}
+static int lan8814_cable_test_one_pair(struct phy_device *phydev, int pair)
+{
+ static const int ethtool_pair[] = { ETHTOOL_A_CABLE_PAIR_A,
+ ETHTOOL_A_CABLE_PAIR_B,
+ ETHTOOL_A_CABLE_PAIR_C,
+ ETHTOOL_A_CABLE_PAIR_D,
+ };
+ u32 fault_length;
+ int ret;
+ int val;
+
+ val = KSZ8081_LMD_ENABLE_TEST;
+ val = val | (pair << LAN8814_PAIR_BIT_SHIFT);
+
+ ret = phy_write(phydev, LAN8814_CABLE_DIAG, val);
+ if (ret < 0)
+ return ret;
+
+ ret = ksz886x_cable_test_wait_for_completion(phydev);
+ if (ret)
+ return ret;
+
+ val = phy_read(phydev, LAN8814_CABLE_DIAG);
+ if (val < 0)
+ return val;
+
+ if (ksz886x_cable_test_failed(val, LAN8814_CABLE_DIAG_STAT_MASK))
+ return -EAGAIN;
+
+ ret = ethnl_cable_test_result(phydev, ethtool_pair[pair],
+ ksz886x_cable_test_result_trans(val,
+ LAN8814_CABLE_DIAG_STAT_MASK
+ ));
+ if (ret)
+ return ret;
+
+ if (!ksz886x_cable_test_fault_length_valid(val, LAN8814_CABLE_DIAG_STAT_MASK))
+ return 0;
+
+ fault_length = ksz886x_cable_test_fault_length(phydev, val,
+ LAN8814_CABLE_DIAG_VCT_DATA_MASK);
+
+ return ethnl_cable_test_fault_length(phydev, ethtool_pair[pair], fault_length);
+}
+
static int ksz886x_cable_test_one_pair(struct phy_device *phydev, int pair)
{
static const int ethtool_pair[] = {
@@ -1872,6 +1951,7 @@ static int ksz886x_cable_test_one_pair(struct phy_device *phydev, int pair)
ETHTOOL_A_CABLE_PAIR_B,
};
int ret, val, mdix;
+ u32 fault_length;
/* There is no way to choice the pair, like we do one ksz9031.
* We can workaround this limitation by using the MDI-X functionality.
@@ -1910,25 +1990,27 @@ static int ksz886x_cable_test_one_pair(struct phy_device *phydev, int pair)
if (val < 0)
return val;
- if (ksz886x_cable_test_failed(val))
+ if (ksz886x_cable_test_failed(val, KSZ8081_LMD_STAT_MASK))
return -EAGAIN;
ret = ethnl_cable_test_result(phydev, ethtool_pair[pair],
- ksz886x_cable_test_result_trans(val));
+ ksz886x_cable_test_result_trans(val, KSZ8081_LMD_STAT_MASK));
if (ret)
return ret;
- if (!ksz886x_cable_test_fault_length_valid(val))
+ if (!ksz886x_cable_test_fault_length_valid(val, KSZ8081_LMD_STAT_MASK))
return 0;
- return ethnl_cable_test_fault_length(phydev, ethtool_pair[pair],
- ksz886x_cable_test_fault_length(val));
+ fault_length = ksz886x_cable_test_fault_length(phydev, val, KSZ8081_LMD_DELTA_TIME_MASK);
+
+ return ethnl_cable_test_fault_length(phydev, ethtool_pair[pair], fault_length);
}
static int ksz886x_cable_test_get_status(struct phy_device *phydev,
bool *finished)
{
- unsigned long pair_mask = 0x3;
+ const struct kszphy_type *type = phydev->drv->driver_data;
+ unsigned long pair_mask = type->pair_mask;
int retries = 20;
int pair, ret;
@@ -1937,7 +2019,10 @@ static int ksz886x_cable_test_get_status(struct phy_device *phydev,
/* Try harder if link partner is active */
while (pair_mask && retries--) {
for_each_set_bit(pair, &pair_mask, 4) {
- ret = ksz886x_cable_test_one_pair(phydev, pair);
+ if (type->cable_diag_reg == LAN8814_CABLE_DIAG)
+ ret = lan8814_cable_test_one_pair(phydev, pair);
+ else
+ ret = ksz886x_cable_test_one_pair(phydev, pair);
if (ret == -EAGAIN)
continue;
if (ret < 0)
@@ -3111,6 +3196,7 @@ static struct phy_driver ksphy_driver[] = {
.phy_id = PHY_ID_LAN8814,
.phy_id_mask = MICREL_PHY_ID_MASK,
.name = "Microchip INDY Gigabit Quad PHY",
+ .flags = PHY_POLL_CABLE_TEST,
.config_init = lan8814_config_init,
.driver_data = &lan8814_type,
.probe = lan8814_probe,
@@ -3123,6 +3209,8 @@ static struct phy_driver ksphy_driver[] = {
.resume = kszphy_resume,
.config_intr = lan8814_config_intr,
.handle_interrupt = lan8814_handle_interrupt,
+ .cable_test_start = lan8814_cable_test_start,
+ .cable_test_get_status = ksz886x_cable_test_get_status,
}, {
.phy_id = PHY_ID_LAN8804,
.phy_id_mask = MICREL_PHY_ID_MASK,
@@ -3169,6 +3257,7 @@ static struct phy_driver ksphy_driver[] = {
.phy_id = PHY_ID_KSZ886X,
.phy_id_mask = MICREL_PHY_ID_MASK,
.name = "Micrel KSZ8851 Ethernet MAC or KSZ886X Switch",
+ .driver_data = &ksz886x_type,
/* PHY_BASIC_FEATURES */
.flags = PHY_POLL_CABLE_TEST,
.config_init = kszphy_config_init,
Support for Cable Diagnostics in lan8814 phy Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com> --- drivers/net/phy/micrel.c | 125 +++++++++++++++++++++++++++++++++------ 1 file changed, 107 insertions(+), 18 deletions(-)