| Message ID | 20221007151647.98222-1-Ryan.Wanner@microchip.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | pinctrl:at91-pio4:add support for pullup/down | expand |
On 07/10/2022 at 17:16, Ryan.Wanner@microchip.com wrote: > From: Ryan Wanner <Ryan.Wanner@microchip.com> > > This patch set adds support for pull up/down pinctl configuration. > The implementation is based off of other pinctl drivers that have > implemented line bias configurations. > > The second patch addes a case for PIN_CONFIG_PERSIST_STATE > this shows up becuse the gpiod api passes this into the new config_set > function that was just implemented. Looking at other drivers like TI > driver, added the ENOTSUPP to the switch case for that state flag. > > How this was tested was by using a gpio program that I created to test > configuration from userspace. This program was run in the Tested using the ioctl GPIO_V2_GET_LINE_IOCTL and with the configs flags: GPIO_V2_LINE_FLAG_BIAS_PULL_DOWN, GPIO_V2_LINE_FLAG_BIAS_PULL_UP and GPIO_V2_LINE_FLAG_BIAS_DISABLED. > background using & then using gpioinfo function checked if the change > has been detected by the gpiod api. Then using devmem reading the > regester making sure that the correct bit was set. The registers where > checked before and during the program is being run, making sure the > change happens. > > In the program Pin 127 would be passed into the test program. Before > the program was ran devmem for pin 127 config register. After > the progam is running in the background devmem for the same status > register is called, the result is showing the change in pinconfig. > The device used to test was the SAMA5D27_som1_ek. Same here, on sama5d27 som1 ek board: Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com> Thanks, best regards, Nicolas > > Ryan Wanner (2): > pinctrl: at91-pio4: Add configuration to userspace > pinctrl: at91-pio4: Add persist state case in config > > drivers/pinctrl/pinctrl-at91-pio4.c | 26 ++++++++++++++++++++++++++ > 1 file changed, 26 insertions(+) >
On Fri, Oct 7, 2022 at 5:16 PM <Ryan.Wanner@microchip.com> wrote: > From: Ryan Wanner <Ryan.Wanner@microchip.com> > > This patch set adds support for pull up/down pinctl configuration. > The implementation is based off of other pinctl drivers that have > implemented line bias configurations. > > The second patch addes a case for PIN_CONFIG_PERSIST_STATE > this shows up becuse the gpiod api passes this into the new config_set > function that was just implemented. Looking at other drivers like TI > driver, added the ENOTSUPP to the switch case for that state flag. > > How this was tested was by using a gpio program that I created to test > configuration from userspace. This program was run in the > background using & then using gpioinfo function checked if the change > has been detected by the gpiod api. Then using devmem reading the > regester making sure that the correct bit was set. The registers where > checked before and during the program is being run, making sure the > change happens. > > In the program Pin 127 would be passed into the test program. Before > the program was ran devmem for pin 127 config register. After > the progam is running in the background devmem for the same status > register is called, the result is showing the change in pinconfig. > The device used to test was the SAMA5D27_som1_ek. > > Ryan Wanner (2): > pinctrl: at91-pio4: Add configuration to userspace > pinctrl: at91-pio4: Add persist state case in config Patches applied! Yours, Linus Walleij
From: Ryan Wanner <Ryan.Wanner@microchip.com> This patch set adds support for pull up/down pinctl configuration. The implementation is based off of other pinctl drivers that have implemented line bias configurations. The second patch addes a case for PIN_CONFIG_PERSIST_STATE this shows up becuse the gpiod api passes this into the new config_set function that was just implemented. Looking at other drivers like TI driver, added the ENOTSUPP to the switch case for that state flag. How this was tested was by using a gpio program that I created to test configuration from userspace. This program was run in the background using & then using gpioinfo function checked if the change has been detected by the gpiod api. Then using devmem reading the regester making sure that the correct bit was set. The registers where checked before and during the program is being run, making sure the change happens. In the program Pin 127 would be passed into the test program. Before the program was ran devmem for pin 127 config register. After the progam is running in the background devmem for the same status register is called, the result is showing the change in pinconfig. The device used to test was the SAMA5D27_som1_ek. Ryan Wanner (2): pinctrl: at91-pio4: Add configuration to userspace pinctrl: at91-pio4: Add persist state case in config drivers/pinctrl/pinctrl-at91-pio4.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)