@@ -1214,6 +1214,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
stm32mp151a-prtt1a.dtb \
stm32mp151a-prtt1c.dtb \
stm32mp151a-prtt1s.dtb \
+ stm32mp151a-dhcor-testbench.dtb \
stm32mp153c-dhcom-drc02.dtb \
stm32mp153c-dhcor-drc-compact.dtb \
stm32mp157a-avenger96.dtb \
new file mode 100644
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+
+#include "stm32mp151.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-testbench.dtsi"
+
+/ {
+ model = "DH electronics STM32MP151A DHCOR Testbench";
+ compatible = "dh,stm32mp151a-dhcor-testbench",
+ "dh,stm32mp151a-dhcor-som",
+ "st,stm32mp151";
+};
new file mode 100644
@@ -0,0 +1,171 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+/ {
+ aliases {
+ ethernet0 = ðernet0;
+ mmc0 = &sdmmc1;
+ mmc1 = &sdmmc2;
+ serial0 = &uart4;
+ serial1 = &uart7;
+ spi0 = &qspi;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ sd_switch: regulator-sd_switch {
+ compatible = "regulator-gpio";
+ regulator-name = "sd_switch";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-type = "voltage";
+ regulator-always-on;
+
+ gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <1800000 0x1>,
+ <2900000 0x0>;
+ };
+};
+
+&adc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&adc12_ain_pins_b>;
+ vdd-supply = <&vdd>;
+ vdda-supply = <&vdda>;
+ vref-supply = <&vdda>;
+ status = "okay";
+
+ adc1: adc@0 {
+ st,adc-channels = <0 1 6>;
+ st,min-sample-time-nsecs = <5000>;
+ status = "okay";
+ };
+
+ adc2: adc@100 {
+ st,adc-channels = <0 1 2>;
+ st,min-sample-time-nsecs = <5000>;
+ status = "okay";
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_c>;
+ pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <1000>;
+ reset-post-delay-us = <1000>;
+
+ phy0: ethernet-phy@7 {
+ reg = <7>;
+
+ rxc-skew-ps = <1500>;
+ rxdv-skew-ps = <540>;
+ rxd0-skew-ps = <420>;
+ rxd1-skew-ps = <420>;
+ rxd2-skew-ps = <420>;
+ rxd3-skew-ps = <420>;
+
+ txc-skew-ps = <1440>;
+ txen-skew-ps = <540>;
+ txd0-skew-ps = <420>;
+ txd1-skew-ps = <420>;
+ txd2-skew-ps = <420>;
+ txd3-skew-ps = <420>;
+ };
+ };
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
+ cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
+ st,sig-dir;
+ st,neg-edge;
+ st,use-ckin;
+ bus-width = <4>;
+ vmmc-supply = <&vdd_sd>;
+ vqmmc-supply = <&sd_switch>;
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ no-sd;
+ no-sdio;
+ non-removable;
+ st,neg-edge;
+ vmmc-supply = <&v3v3>;
+ vqmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_b>;
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ uart-has-rtscts;
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+};
+
+&usbh_ehci {
+ phys = <&usbphyc_port0>;
+ status = "okay";
+};
+
+&usbh_ohci {
+ phys = <&usbphyc_port0>;
+ status = "okay";
+};
+
+&usbotg_hs {
+ pinctrl-0 = <&usbotg_hs_pins_a>;
+ pinctrl-names = "default";
+ phy-names = "usb2-phy";
+ phys = <&usbphyc_port1 0>;
+ status = "okay";
+ vbus-supply = <&vbus_otg>;
+};
+
+&usbphyc {
+ status = "okay";
+};
+
+&usbphyc_port0 {
+ phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+ phy-supply = <&vdd_usb>;
+};
Add DT for DHCOR Testbench board, which is a testbench for testing of DHCOR SoM during manufacturing. This is effectively a trimmed down version of AV96 board with CSI-2 bridge, HDMI bridge, WiFi, Audio and LEDs removed and used as GPIOs instead. Furthermore, the PMIC Buck3 is always configured from PMIC NVM to cater for both 1V8 and 3V3 SoM variant. Signed-off-by: Marek Vasut <marex@denx.de> --- Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org --- arch/arm/boot/dts/Makefile | 1 + .../boot/dts/stm32mp151a-dhcor-testbench.dts | 17 ++ .../boot/dts/stm32mp15xx-dhcor-testbench.dtsi | 171 ++++++++++++++++++ 3 files changed, 189 insertions(+) create mode 100644 arch/arm/boot/dts/stm32mp151a-dhcor-testbench.dts create mode 100644 arch/arm/boot/dts/stm32mp15xx-dhcor-testbench.dtsi