Message ID | 20221029141633.295650-11-manivannan.sadhasivam@linaro.org (mailing list archive) |
---|---|
State | Superseded |
Headers | show |
Series | ufs: qcom: Add HS-G4 support | expand |
On 29/10/2022 17:16, Manivannan Sadhasivam wrote: > Use bitfield macros where appropriate to simplify the driver. > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > --- > drivers/ufs/host/ufs-qcom.h | 58 ++++++++++++++++--------------------- > 1 file changed, 25 insertions(+), 33 deletions(-) > Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h > index 44466a395bb5..6cb0776456b3 100644 > --- a/drivers/ufs/host/ufs-qcom.h > +++ b/drivers/ufs/host/ufs-qcom.h > @@ -17,12 +17,9 @@ > #define DEFAULT_CLK_RATE_HZ 1000000 > #define BUS_VECTOR_NAME_LEN 32 > > -#define UFS_HW_VER_MAJOR_SHFT (28) > -#define UFS_HW_VER_MAJOR_MASK (0x000F << UFS_HW_VER_MAJOR_SHFT) > -#define UFS_HW_VER_MINOR_SHFT (16) > -#define UFS_HW_VER_MINOR_MASK (0x0FFF << UFS_HW_VER_MINOR_SHFT) > -#define UFS_HW_VER_STEP_SHFT (0) > -#define UFS_HW_VER_STEP_MASK (0xFFFF << UFS_HW_VER_STEP_SHFT) > +#define UFS_HW_VER_MAJOR_MASK GENMASK(31, 28) > +#define UFS_HW_VER_MINOR_MASK GENMASK(27, 16) > +#define UFS_HW_VER_STEP_MASK GENMASK(15, 0) > > /* vendor specific pre-defined parameters */ > #define SLOW 1 > @@ -76,24 +73,24 @@ enum { > #define UFS_CNTLR_3_x_x_VEN_REGS_OFFSET(x) (0x400 + x) > > /* bit definitions for REG_UFS_CFG1 register */ > -#define QUNIPRO_SEL 0x1 > -#define UTP_DBG_RAMS_EN 0x20000 > +#define QUNIPRO_SEL BIT(0) > +#define UTP_DBG_RAMS_EN BIT(17) > #define TEST_BUS_EN BIT(18) > #define TEST_BUS_SEL GENMASK(22, 19) > #define UFS_REG_TEST_BUS_EN BIT(30) > > /* bit definitions for REG_UFS_CFG2 register */ > -#define UAWM_HW_CGC_EN (1 << 0) > -#define UARM_HW_CGC_EN (1 << 1) > -#define TXUC_HW_CGC_EN (1 << 2) > -#define RXUC_HW_CGC_EN (1 << 3) > -#define DFC_HW_CGC_EN (1 << 4) > -#define TRLUT_HW_CGC_EN (1 << 5) > -#define TMRLUT_HW_CGC_EN (1 << 6) > -#define OCSC_HW_CGC_EN (1 << 7) > +#define UAWM_HW_CGC_EN BIT(0) > +#define UARM_HW_CGC_EN BIT(1) > +#define TXUC_HW_CGC_EN BIT(2) > +#define RXUC_HW_CGC_EN BIT(3) > +#define DFC_HW_CGC_EN BIT(4) > +#define TRLUT_HW_CGC_EN BIT(5) > +#define TMRLUT_HW_CGC_EN BIT(6) > +#define OCSC_HW_CGC_EN BIT(7) > > /* bit definition for UFS_UFS_TEST_BUS_CTRL_n */ > -#define TEST_BUS_SUB_SEL_MASK 0x1F /* All XXX_SEL fields are 5 bits wide */ > +#define TEST_BUS_SUB_SEL_MASK GENMASK(4, 0) /* All XXX_SEL fields are 5 bits wide */ > > #define REG_UFS_CFG2_CGC_EN_ALL (UAWM_HW_CGC_EN | UARM_HW_CGC_EN |\ > TXUC_HW_CGC_EN | RXUC_HW_CGC_EN |\ > @@ -101,17 +98,12 @@ enum { > TMRLUT_HW_CGC_EN | OCSC_HW_CGC_EN) > > /* bit offset */ > -enum { > - OFFSET_UFS_PHY_SOFT_RESET = 1, > - OFFSET_CLK_NS_REG = 10, > -}; > +#define OFFSET_CLK_NS_REG 0xa > > /* bit masks */ > -enum { > - MASK_UFS_PHY_SOFT_RESET = 0x2, > - MASK_TX_SYMBOL_CLK_1US_REG = 0x3FF, > - MASK_CLK_NS_REG = 0xFFFC00, > -}; > +#define MASK_UFS_PHY_SOFT_RESET BIT(1) > +#define MASK_TX_SYMBOL_CLK_1US_REG GENMASK(9, 0) > +#define MASK_CLK_NS_REG GENMASK(23, 10) > > /* QCOM UFS debug print bit mask */ > #define UFS_QCOM_DBG_PRINT_REGS_EN BIT(0) > @@ -135,15 +127,15 @@ ufs_qcom_get_controller_revision(struct ufs_hba *hba, > { > u32 ver = ufshcd_readl(hba, REG_UFS_HW_VERSION); > > - *major = (ver & UFS_HW_VER_MAJOR_MASK) >> UFS_HW_VER_MAJOR_SHFT; > - *minor = (ver & UFS_HW_VER_MINOR_MASK) >> UFS_HW_VER_MINOR_SHFT; > - *step = (ver & UFS_HW_VER_STEP_MASK) >> UFS_HW_VER_STEP_SHFT; > + *major = FIELD_GET(UFS_HW_VER_MAJOR_MASK, ver); > + *minor = FIELD_GET(UFS_HW_VER_MINOR_MASK, ver); > + *step = FIELD_GET(UFS_HW_VER_STEP_MASK, ver); > }; > > static inline void ufs_qcom_assert_reset(struct ufs_hba *hba) > { > - ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, > - 1 << OFFSET_UFS_PHY_SOFT_RESET, REG_UFS_CFG1); > + ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, FIELD_PREP(MASK_UFS_PHY_SOFT_RESET, 1), Nit: I'd just define the value too and use the defined name here. > + REG_UFS_CFG1); > > /* > * Make sure assertion of ufs phy reset is written to > @@ -154,8 +146,8 @@ static inline void ufs_qcom_assert_reset(struct ufs_hba *hba) > > static inline void ufs_qcom_deassert_reset(struct ufs_hba *hba) > { > - ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, > - 0 << OFFSET_UFS_PHY_SOFT_RESET, REG_UFS_CFG1); > + ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, FIELD_PREP(MASK_UFS_PHY_SOFT_RESET, 0), Nit: FIELD_PREP is always 0. > + REG_UFS_CFG1); > > /* > * Make sure de-assertion of ufs phy reset is written to
On Sun, Oct 30, 2022 at 12:58:57AM +0300, Dmitry Baryshkov wrote: > On 29/10/2022 17:16, Manivannan Sadhasivam wrote: > > Use bitfield macros where appropriate to simplify the driver. > > > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > --- > > drivers/ufs/host/ufs-qcom.h | 58 ++++++++++++++++--------------------- > > 1 file changed, 25 insertions(+), 33 deletions(-) > > > > Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > > > diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h > > index 44466a395bb5..6cb0776456b3 100644 > > --- a/drivers/ufs/host/ufs-qcom.h > > +++ b/drivers/ufs/host/ufs-qcom.h > > @@ -17,12 +17,9 @@ > > #define DEFAULT_CLK_RATE_HZ 1000000 > > #define BUS_VECTOR_NAME_LEN 32 > > -#define UFS_HW_VER_MAJOR_SHFT (28) > > -#define UFS_HW_VER_MAJOR_MASK (0x000F << UFS_HW_VER_MAJOR_SHFT) > > -#define UFS_HW_VER_MINOR_SHFT (16) > > -#define UFS_HW_VER_MINOR_MASK (0x0FFF << UFS_HW_VER_MINOR_SHFT) > > -#define UFS_HW_VER_STEP_SHFT (0) > > -#define UFS_HW_VER_STEP_MASK (0xFFFF << UFS_HW_VER_STEP_SHFT) > > +#define UFS_HW_VER_MAJOR_MASK GENMASK(31, 28) > > +#define UFS_HW_VER_MINOR_MASK GENMASK(27, 16) > > +#define UFS_HW_VER_STEP_MASK GENMASK(15, 0) > > /* vendor specific pre-defined parameters */ > > #define SLOW 1 > > @@ -76,24 +73,24 @@ enum { > > #define UFS_CNTLR_3_x_x_VEN_REGS_OFFSET(x) (0x400 + x) > > /* bit definitions for REG_UFS_CFG1 register */ > > -#define QUNIPRO_SEL 0x1 > > -#define UTP_DBG_RAMS_EN 0x20000 > > +#define QUNIPRO_SEL BIT(0) > > +#define UTP_DBG_RAMS_EN BIT(17) > > #define TEST_BUS_EN BIT(18) > > #define TEST_BUS_SEL GENMASK(22, 19) > > #define UFS_REG_TEST_BUS_EN BIT(30) > > /* bit definitions for REG_UFS_CFG2 register */ > > -#define UAWM_HW_CGC_EN (1 << 0) > > -#define UARM_HW_CGC_EN (1 << 1) > > -#define TXUC_HW_CGC_EN (1 << 2) > > -#define RXUC_HW_CGC_EN (1 << 3) > > -#define DFC_HW_CGC_EN (1 << 4) > > -#define TRLUT_HW_CGC_EN (1 << 5) > > -#define TMRLUT_HW_CGC_EN (1 << 6) > > -#define OCSC_HW_CGC_EN (1 << 7) > > +#define UAWM_HW_CGC_EN BIT(0) > > +#define UARM_HW_CGC_EN BIT(1) > > +#define TXUC_HW_CGC_EN BIT(2) > > +#define RXUC_HW_CGC_EN BIT(3) > > +#define DFC_HW_CGC_EN BIT(4) > > +#define TRLUT_HW_CGC_EN BIT(5) > > +#define TMRLUT_HW_CGC_EN BIT(6) > > +#define OCSC_HW_CGC_EN BIT(7) > > /* bit definition for UFS_UFS_TEST_BUS_CTRL_n */ > > -#define TEST_BUS_SUB_SEL_MASK 0x1F /* All XXX_SEL fields are 5 bits wide */ > > +#define TEST_BUS_SUB_SEL_MASK GENMASK(4, 0) /* All XXX_SEL fields are 5 bits wide */ > > #define REG_UFS_CFG2_CGC_EN_ALL (UAWM_HW_CGC_EN | UARM_HW_CGC_EN |\ > > TXUC_HW_CGC_EN | RXUC_HW_CGC_EN |\ > > @@ -101,17 +98,12 @@ enum { > > TMRLUT_HW_CGC_EN | OCSC_HW_CGC_EN) > > /* bit offset */ > > -enum { > > - OFFSET_UFS_PHY_SOFT_RESET = 1, > > - OFFSET_CLK_NS_REG = 10, > > -}; > > +#define OFFSET_CLK_NS_REG 0xa > > /* bit masks */ > > -enum { > > - MASK_UFS_PHY_SOFT_RESET = 0x2, > > - MASK_TX_SYMBOL_CLK_1US_REG = 0x3FF, > > - MASK_CLK_NS_REG = 0xFFFC00, > > -}; > > +#define MASK_UFS_PHY_SOFT_RESET BIT(1) > > +#define MASK_TX_SYMBOL_CLK_1US_REG GENMASK(9, 0) > > +#define MASK_CLK_NS_REG GENMASK(23, 10) > > /* QCOM UFS debug print bit mask */ > > #define UFS_QCOM_DBG_PRINT_REGS_EN BIT(0) > > @@ -135,15 +127,15 @@ ufs_qcom_get_controller_revision(struct ufs_hba *hba, > > { > > u32 ver = ufshcd_readl(hba, REG_UFS_HW_VERSION); > > - *major = (ver & UFS_HW_VER_MAJOR_MASK) >> UFS_HW_VER_MAJOR_SHFT; > > - *minor = (ver & UFS_HW_VER_MINOR_MASK) >> UFS_HW_VER_MINOR_SHFT; > > - *step = (ver & UFS_HW_VER_STEP_MASK) >> UFS_HW_VER_STEP_SHFT; > > + *major = FIELD_GET(UFS_HW_VER_MAJOR_MASK, ver); > > + *minor = FIELD_GET(UFS_HW_VER_MINOR_MASK, ver); > > + *step = FIELD_GET(UFS_HW_VER_STEP_MASK, ver); > > }; > > static inline void ufs_qcom_assert_reset(struct ufs_hba *hba) > > { > > - ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, > > - 1 << OFFSET_UFS_PHY_SOFT_RESET, REG_UFS_CFG1); > > + ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, FIELD_PREP(MASK_UFS_PHY_SOFT_RESET, 1), > > Nit: I'd just define the value too and use the defined name here. > > > + REG_UFS_CFG1); > > /* > > * Make sure assertion of ufs phy reset is written to > > @@ -154,8 +146,8 @@ static inline void ufs_qcom_assert_reset(struct ufs_hba *hba) > > static inline void ufs_qcom_deassert_reset(struct ufs_hba *hba) > > { > > - ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, > > - 0 << OFFSET_UFS_PHY_SOFT_RESET, REG_UFS_CFG1); > > + ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, FIELD_PREP(MASK_UFS_PHY_SOFT_RESET, 0), > > Nit: FIELD_PREP is always 0. > I know but this make the code in sync with reset assert. Thanks, Mani > > + REG_UFS_CFG1); > > /* > > * Make sure de-assertion of ufs phy reset is written to > > -- > With best wishes > Dmitry >
diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h index 44466a395bb5..6cb0776456b3 100644 --- a/drivers/ufs/host/ufs-qcom.h +++ b/drivers/ufs/host/ufs-qcom.h @@ -17,12 +17,9 @@ #define DEFAULT_CLK_RATE_HZ 1000000 #define BUS_VECTOR_NAME_LEN 32 -#define UFS_HW_VER_MAJOR_SHFT (28) -#define UFS_HW_VER_MAJOR_MASK (0x000F << UFS_HW_VER_MAJOR_SHFT) -#define UFS_HW_VER_MINOR_SHFT (16) -#define UFS_HW_VER_MINOR_MASK (0x0FFF << UFS_HW_VER_MINOR_SHFT) -#define UFS_HW_VER_STEP_SHFT (0) -#define UFS_HW_VER_STEP_MASK (0xFFFF << UFS_HW_VER_STEP_SHFT) +#define UFS_HW_VER_MAJOR_MASK GENMASK(31, 28) +#define UFS_HW_VER_MINOR_MASK GENMASK(27, 16) +#define UFS_HW_VER_STEP_MASK GENMASK(15, 0) /* vendor specific pre-defined parameters */ #define SLOW 1 @@ -76,24 +73,24 @@ enum { #define UFS_CNTLR_3_x_x_VEN_REGS_OFFSET(x) (0x400 + x) /* bit definitions for REG_UFS_CFG1 register */ -#define QUNIPRO_SEL 0x1 -#define UTP_DBG_RAMS_EN 0x20000 +#define QUNIPRO_SEL BIT(0) +#define UTP_DBG_RAMS_EN BIT(17) #define TEST_BUS_EN BIT(18) #define TEST_BUS_SEL GENMASK(22, 19) #define UFS_REG_TEST_BUS_EN BIT(30) /* bit definitions for REG_UFS_CFG2 register */ -#define UAWM_HW_CGC_EN (1 << 0) -#define UARM_HW_CGC_EN (1 << 1) -#define TXUC_HW_CGC_EN (1 << 2) -#define RXUC_HW_CGC_EN (1 << 3) -#define DFC_HW_CGC_EN (1 << 4) -#define TRLUT_HW_CGC_EN (1 << 5) -#define TMRLUT_HW_CGC_EN (1 << 6) -#define OCSC_HW_CGC_EN (1 << 7) +#define UAWM_HW_CGC_EN BIT(0) +#define UARM_HW_CGC_EN BIT(1) +#define TXUC_HW_CGC_EN BIT(2) +#define RXUC_HW_CGC_EN BIT(3) +#define DFC_HW_CGC_EN BIT(4) +#define TRLUT_HW_CGC_EN BIT(5) +#define TMRLUT_HW_CGC_EN BIT(6) +#define OCSC_HW_CGC_EN BIT(7) /* bit definition for UFS_UFS_TEST_BUS_CTRL_n */ -#define TEST_BUS_SUB_SEL_MASK 0x1F /* All XXX_SEL fields are 5 bits wide */ +#define TEST_BUS_SUB_SEL_MASK GENMASK(4, 0) /* All XXX_SEL fields are 5 bits wide */ #define REG_UFS_CFG2_CGC_EN_ALL (UAWM_HW_CGC_EN | UARM_HW_CGC_EN |\ TXUC_HW_CGC_EN | RXUC_HW_CGC_EN |\ @@ -101,17 +98,12 @@ enum { TMRLUT_HW_CGC_EN | OCSC_HW_CGC_EN) /* bit offset */ -enum { - OFFSET_UFS_PHY_SOFT_RESET = 1, - OFFSET_CLK_NS_REG = 10, -}; +#define OFFSET_CLK_NS_REG 0xa /* bit masks */ -enum { - MASK_UFS_PHY_SOFT_RESET = 0x2, - MASK_TX_SYMBOL_CLK_1US_REG = 0x3FF, - MASK_CLK_NS_REG = 0xFFFC00, -}; +#define MASK_UFS_PHY_SOFT_RESET BIT(1) +#define MASK_TX_SYMBOL_CLK_1US_REG GENMASK(9, 0) +#define MASK_CLK_NS_REG GENMASK(23, 10) /* QCOM UFS debug print bit mask */ #define UFS_QCOM_DBG_PRINT_REGS_EN BIT(0) @@ -135,15 +127,15 @@ ufs_qcom_get_controller_revision(struct ufs_hba *hba, { u32 ver = ufshcd_readl(hba, REG_UFS_HW_VERSION); - *major = (ver & UFS_HW_VER_MAJOR_MASK) >> UFS_HW_VER_MAJOR_SHFT; - *minor = (ver & UFS_HW_VER_MINOR_MASK) >> UFS_HW_VER_MINOR_SHFT; - *step = (ver & UFS_HW_VER_STEP_MASK) >> UFS_HW_VER_STEP_SHFT; + *major = FIELD_GET(UFS_HW_VER_MAJOR_MASK, ver); + *minor = FIELD_GET(UFS_HW_VER_MINOR_MASK, ver); + *step = FIELD_GET(UFS_HW_VER_STEP_MASK, ver); }; static inline void ufs_qcom_assert_reset(struct ufs_hba *hba) { - ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, - 1 << OFFSET_UFS_PHY_SOFT_RESET, REG_UFS_CFG1); + ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, FIELD_PREP(MASK_UFS_PHY_SOFT_RESET, 1), + REG_UFS_CFG1); /* * Make sure assertion of ufs phy reset is written to @@ -154,8 +146,8 @@ static inline void ufs_qcom_assert_reset(struct ufs_hba *hba) static inline void ufs_qcom_deassert_reset(struct ufs_hba *hba) { - ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, - 0 << OFFSET_UFS_PHY_SOFT_RESET, REG_UFS_CFG1); + ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, FIELD_PREP(MASK_UFS_PHY_SOFT_RESET, 0), + REG_UFS_CFG1); /* * Make sure de-assertion of ufs phy reset is written to
Use bitfield macros where appropriate to simplify the driver. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- drivers/ufs/host/ufs-qcom.h | 58 ++++++++++++++++--------------------- 1 file changed, 25 insertions(+), 33 deletions(-)