| Message ID | 20221116145616.17884-8-luca@z3ntu.xyz (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add a bunch of msm8953 dts files | expand |
On 16/11/2022 15:56, Luca Weiss wrote: > From: Eugene Lepshy <fekz115@gmail.com> > > Add device tree for the Xiaomi Redmi 5 Plus (vince) smartphone. This > device is based on Snapdragon 625 (msm8953) SoC. > > Signed-off-by: Eugene Lepshy <fekz115@gmail.com> > Co-developed-by: Gianluca Boiano <morf3089@gmail.com> > Signed-off-by: Gianluca Boiano <morf3089@gmail.com> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../boot/dts/qcom/msm8953-xiaomi-vince.dts | 330 ++++++++++++++++++ > 2 files changed, 331 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/msm8953-xiaomi-vince.dts > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 9517638b2fdd..bed490c095dd 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -25,6 +25,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8953-motorola-potter.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-daisy.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-mido.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-tissot.dtb > +dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-vince.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8992-lg-bullhead-rev-10.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8992-lg-bullhead-rev-101.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8992-msft-lumia-octagon-talkman.dtb > diff --git a/arch/arm64/boot/dts/qcom/msm8953-xiaomi-vince.dts b/arch/arm64/boot/dts/qcom/msm8953-xiaomi-vince.dts > new file mode 100644 > index 000000000000..da029aaa99a1 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8953-xiaomi-vince.dts > @@ -0,0 +1,330 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/dts-v1/; > + > +#include "msm8953.dtsi" > +#include "pm8953.dtsi" > +#include "pmi8950.dtsi" > +#include <dt-bindings/leds/common.h> > + > +/ { > + model = "Xiaomi Redmi 5 Plus"; > + compatible = "xiaomi,vince", "qcom,msm8953"; > + chassis-type = "handset"; > + qcom,msm-id = <293 0>; > + qcom,board-id= <0x1000b 0x08>; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&gpio_key_default>; > + > + key-volume-up { > + label = "volume_up"; > + linux,code = <KEY_VOLUMEUP>; > + gpios = <&tlmm 85 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + reserved-memory { > + /delete-node/ memory@85b00000; > + memory@84a00000 { > + reg = <0x0 0x84a00000 0x0 0x1900000>; > + no-map; > + }; > + > + cont_splash_mem: memory@90001000 { > + reg = <0x0 0x90001000 0x0 (1080 * 2160 * 3)>; > + no-map; > + }; > + > + /delete-node/ memory@8d600000; > + adsp_fw_mem: memory@8d600000 { > + reg = <0x0 0x8d600000 0x0 0x1200000>; > + no-map; > + }; > + > + /delete-node/ memory@8e700000; > + wcnss_fw_mem: memory@8e800000 { > + reg = <0x0 0x8e800000 0x0 0x700000>; > + no-map; > + }; > + > + ramoops@9ff00000 { > + compatible = "ramoops"; > + reg = <0x0 0x9ff00000 0x0 0x100000>; > + record-size = <0x1000>; > + console-size = <0x80000>; > + ftrace-size = <0x1000>; > + pmsg-size = <0x8000>; > + }; > + }; > + > + i2c-gpio { > + compatible = "i2c-gpio"; > + sda-gpios = <&tlmm 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; > + scl-gpios = <&tlmm 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; > + i2c-gpio,delay-us = <2>; /* ~100 kHz */ > + #address-cells = <1>; > + #size-cells = <0>; > + > + imu@6a { > + compatible = "st,lsm6dsl"; > + reg = <0x6a>; > + vdd-supply = <&pm8953_l10>; > + vddio-supply = <&pm8953_l6>; > + mount-matrix = "1", "0", "0", > + "0", "-1", "0", > + "0", "0", "1"; > + }; > + }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vph_pwr"; > + regulator-always-on; > + regulator-boot-on; > + }; > +}; > + > +&hsusb_phy { > + vdd-supply = <&pm8953_l3>; > + vdda-pll-supply = <&pm8953_l7>; > + vdda-phy-dpdm-supply = <&pm8953_l13>; > + > + status = "okay"; > +}; > + > +&i2c_2 { > + status = "okay"; > + > + led-controller@45 { > + compatible = "awinic,aw2013"; > + reg = <0x45>; > + > + vcc-supply = <&pm8953_l10>; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + led@0 { > + reg = <0>; > + led-max-microamp = <5000>; > + function = LED_FUNCTION_INDICATOR; > + color = <LED_COLOR_ID_WHITE>; > + }; > + }; > +}; > + > +&i2c_3 { > + status = "okay"; > + > + touchscreen@20 { > + reg = <0x20>; > + compatible = "syna,rmi4-i2c"; > + interrupts-parent = <&tlmm>; > + interrupts-extended = <&tlmm 65 IRQ_TYPE_EDGE_FALLING>; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + vdd-supply = <&pm8953_l10>; > + vio-supply = <&pm8953_l6>; > + > + pinctrl-names = "init", "suspend"; > + pinctrl-0 = <&ts_reset_active &ts_int_active>; > + pinctrl-1 = <&ts_reset_suspend &ts_int_suspend>; > + syna,reset-delay-ms = <200>; > + syna,startup-delay-ms = <500>; > + > + rmi4-f01@1 { > + reg = <0x01>; > + syna,nosleep-mode = <1>; > + }; > + > + rmi4-f12@12 { > + reg = <0x12>; > + syna,rezero-wait-ms = <20>; > + syna,sensor-type = <1>; > + touchscreen-x-mm = <68>; > + touchscreen-y-mm = <122>; > + }; > + }; > +}; > + > +&pm8953_resin { > + linux,code = <KEY_VOLUMEDOWN>; > + status = "okay"; > +}; > + > +&pmi8950_wled { > + qcom,current-limit-microamp = <20000>; > + qcom,ovp-millivolt = <29600>; > + qcom,num-strings = <2>; > + qcom,external-pfet; > + qcom,cabc; > + > + status = "okay"; > +}; > + > +&rpm_requests { > + regulators { > + compatible = "qcom,rpm-pm8953-regulators"; > + vdd_s1-supply = <&vph_pwr>; > + vdd_s2-supply = <&vph_pwr>; > + vdd_s3-supply = <&vph_pwr>; > + vdd_s4-supply = <&vph_pwr>; > + vdd_s5-supply = <&vph_pwr>; > + vdd_s6-supply = <&vph_pwr>; > + vdd_s7-supply = <&vph_pwr>; > + vdd_l1-supply = <&pm8953_s3>; > + vdd_l2_l3-supply = <&pm8953_s3>; > + vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>; > + vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>; > + vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>; > + > + pm8953_s1: s1 { > + regulator-min-microvolt = <870000>; > + regulator-max-microvolt = <1156000>; > + }; > + > + pm8953_s3: s3 { > + regulator-min-microvolt = <984000>; > + regulator-max-microvolt = <1224000>; > + }; Please add a newline after each node. (+delete nodes by referencing their label, check licensing and check if i2c-gpio is necessary as in the rest of the patches) Konrad > + pm8953_s4: s4 { > + regulator-min-microvolt = <1900000>; > + regulator-max-microvolt = <2050000>; > + }; > + pm8953_l1: l1 { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1100000>; > + }; > + pm8953_l2: l2 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1225000>; > + }; > + pm8953_l3: l3 { > + regulator-min-microvolt = <925000>; > + regulator-max-microvolt = <925000>; > + }; > + pm8953_l5: l5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + pm8953_l6: l6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + pm8953_l7: l7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1900000>; > + }; > + pm8953_l8: l8 { > + regulator-min-microvolt = <2900000>; > + regulator-max-microvolt = <2900000>; > + }; > + pm8953_l9: l9 { > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3300000>; > + }; > + pm8953_l10: l10 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > + }; > + pm8953_l11: l11 { > + regulator-min-microvolt = <2950000>; > + regulator-max-microvolt = <2950000>; > + }; > + pm8953_l12: l12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + }; > + pm8953_l13: l13 { > + regulator-min-microvolt = <3125000>; > + regulator-max-microvolt = <3125000>; > + }; > + pm8953_l16: l16 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + pm8953_l17: l17 { > + regulator-min-microvolt = <2750000>; > + regulator-max-microvolt = <2850000>; > + }; > + pm8953_l19: l19 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1380000>; > + }; > + pm8953_l22: l22 { > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + }; > + pm8953_l23: l23 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1225000>; > + }; > + }; > +}; > + > +&sdhc_1 { > + status = "okay"; > +}; > + > +&sdhc_2 { > + vmmc-supply = <&pm8953_l11>; > + vqmmc-supply = <&pm8953_l12>; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; > + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; > + > + status = "okay"; > +}; > + > +&tlmm { > + gpio-reserved-ranges = <0 4>, <16 4>, <135 4>; > + > + ts_reset_active: ts-reset-active-state { > + pins = "gpio64"; > + function = "gpio"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + > + ts_reset_suspend: ts-reset-suspend-state { > + pins = "gpio64"; > + function = "gpio"; > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + ts_int_active: ts-int-active-state { > + pins = "gpio65"; > + function = "gpio"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + > + ts_int_suspend: ts-int-suspend-state { > + pins = "gpio65"; > + function = "gpio"; > + drive-strength = <2>; > + bias-pull-down; > + }; > +}; > + > +&uart_0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart_console_active>; > + > + status = "okay"; > +}; > + > +&usb3 { > + status = "okay"; > +}; > + > +&usb3_dwc3 { > + dr_mode = "peripheral"; > +};
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 9517638b2fdd..bed490c095dd 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -25,6 +25,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8953-motorola-potter.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-daisy.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-mido.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-tissot.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-vince.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8992-lg-bullhead-rev-10.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8992-lg-bullhead-rev-101.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8992-msft-lumia-octagon-talkman.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8953-xiaomi-vince.dts b/arch/arm64/boot/dts/qcom/msm8953-xiaomi-vince.dts new file mode 100644 index 000000000000..da029aaa99a1 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8953-xiaomi-vince.dts @@ -0,0 +1,330 @@ +// SPDX-License-Identifier: GPL-2.0-only +/dts-v1/; + +#include "msm8953.dtsi" +#include "pm8953.dtsi" +#include "pmi8950.dtsi" +#include <dt-bindings/leds/common.h> + +/ { + model = "Xiaomi Redmi 5 Plus"; + compatible = "xiaomi,vince", "qcom,msm8953"; + chassis-type = "handset"; + qcom,msm-id = <293 0>; + qcom,board-id= <0x1000b 0x08>; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_key_default>; + + key-volume-up { + label = "volume_up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&tlmm 85 GPIO_ACTIVE_LOW>; + }; + }; + + reserved-memory { + /delete-node/ memory@85b00000; + memory@84a00000 { + reg = <0x0 0x84a00000 0x0 0x1900000>; + no-map; + }; + + cont_splash_mem: memory@90001000 { + reg = <0x0 0x90001000 0x0 (1080 * 2160 * 3)>; + no-map; + }; + + /delete-node/ memory@8d600000; + adsp_fw_mem: memory@8d600000 { + reg = <0x0 0x8d600000 0x0 0x1200000>; + no-map; + }; + + /delete-node/ memory@8e700000; + wcnss_fw_mem: memory@8e800000 { + reg = <0x0 0x8e800000 0x0 0x700000>; + no-map; + }; + + ramoops@9ff00000 { + compatible = "ramoops"; + reg = <0x0 0x9ff00000 0x0 0x100000>; + record-size = <0x1000>; + console-size = <0x80000>; + ftrace-size = <0x1000>; + pmsg-size = <0x8000>; + }; + }; + + i2c-gpio { + compatible = "i2c-gpio"; + sda-gpios = <&tlmm 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&tlmm 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + + imu@6a { + compatible = "st,lsm6dsl"; + reg = <0x6a>; + vdd-supply = <&pm8953_l10>; + vddio-supply = <&pm8953_l6>; + mount-matrix = "1", "0", "0", + "0", "-1", "0", + "0", "0", "1"; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-always-on; + regulator-boot-on; + }; +}; + +&hsusb_phy { + vdd-supply = <&pm8953_l3>; + vdda-pll-supply = <&pm8953_l7>; + vdda-phy-dpdm-supply = <&pm8953_l13>; + + status = "okay"; +}; + +&i2c_2 { + status = "okay"; + + led-controller@45 { + compatible = "awinic,aw2013"; + reg = <0x45>; + + vcc-supply = <&pm8953_l10>; + + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + led-max-microamp = <5000>; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_WHITE>; + }; + }; +}; + +&i2c_3 { + status = "okay"; + + touchscreen@20 { + reg = <0x20>; + compatible = "syna,rmi4-i2c"; + interrupts-parent = <&tlmm>; + interrupts-extended = <&tlmm 65 IRQ_TYPE_EDGE_FALLING>; + + #address-cells = <1>; + #size-cells = <0>; + + vdd-supply = <&pm8953_l10>; + vio-supply = <&pm8953_l6>; + + pinctrl-names = "init", "suspend"; + pinctrl-0 = <&ts_reset_active &ts_int_active>; + pinctrl-1 = <&ts_reset_suspend &ts_int_suspend>; + syna,reset-delay-ms = <200>; + syna,startup-delay-ms = <500>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4-f12@12 { + reg = <0x12>; + syna,rezero-wait-ms = <20>; + syna,sensor-type = <1>; + touchscreen-x-mm = <68>; + touchscreen-y-mm = <122>; + }; + }; +}; + +&pm8953_resin { + linux,code = <KEY_VOLUMEDOWN>; + status = "okay"; +}; + +&pmi8950_wled { + qcom,current-limit-microamp = <20000>; + qcom,ovp-millivolt = <29600>; + qcom,num-strings = <2>; + qcom,external-pfet; + qcom,cabc; + + status = "okay"; +}; + +&rpm_requests { + regulators { + compatible = "qcom,rpm-pm8953-regulators"; + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_l1-supply = <&pm8953_s3>; + vdd_l2_l3-supply = <&pm8953_s3>; + vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>; + vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>; + vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>; + + pm8953_s1: s1 { + regulator-min-microvolt = <870000>; + regulator-max-microvolt = <1156000>; + }; + + pm8953_s3: s3 { + regulator-min-microvolt = <984000>; + regulator-max-microvolt = <1224000>; + }; + pm8953_s4: s4 { + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <2050000>; + }; + pm8953_l1: l1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + }; + pm8953_l2: l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1225000>; + }; + pm8953_l3: l3 { + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <925000>; + }; + pm8953_l5: l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + pm8953_l6: l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + pm8953_l7: l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1900000>; + }; + pm8953_l8: l8 { + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + }; + pm8953_l9: l9 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + }; + pm8953_l10: l10 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + pm8953_l11: l11 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + }; + pm8953_l12: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + pm8953_l13: l13 { + regulator-min-microvolt = <3125000>; + regulator-max-microvolt = <3125000>; + }; + pm8953_l16: l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + pm8953_l17: l17 { + regulator-min-microvolt = <2750000>; + regulator-max-microvolt = <2850000>; + }; + pm8953_l19: l19 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1380000>; + }; + pm8953_l22: l22 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + pm8953_l23: l23 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1225000>; + }; + }; +}; + +&sdhc_1 { + status = "okay"; +}; + +&sdhc_2 { + vmmc-supply = <&pm8953_l11>; + vqmmc-supply = <&pm8953_l12>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; + + status = "okay"; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <16 4>, <135 4>; + + ts_reset_active: ts-reset-active-state { + pins = "gpio64"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + ts_reset_suspend: ts-reset-suspend-state { + pins = "gpio64"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + + ts_int_active: ts-int-active-state { + pins = "gpio65"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + ts_int_suspend: ts-int-suspend-state { + pins = "gpio65"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; +}; + +&uart_0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart_console_active>; + + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; + +&usb3_dwc3 { + dr_mode = "peripheral"; +};