diff mbox series

[v3,1/2] arm64: dts: rockchip: Add RK3566 LubanCat 1

Message ID Y6Kc650FuvHFWxP0@VM-66-53-centos (mailing list archive)
State New, archived
Headers show
Series [v3,1/2] arm64: dts: rockchip: Add RK3566 LubanCat 1 | expand

Commit Message

ty Dec. 21, 2022, 5:43 a.m. UTC
LubanCat 1 is a Rockchip RK3566 SBC based
is developed by EmbedFire Electronics Co., Ltd.
Mini Linux Card Type Cheap Computer Development Board
It has the following characteristics:
- MicroSD card slot, onboard eMMC flash memory
- 1GbE Realtek RTL8211F Ethernet Transceiver
- 1 USB Type-C port (power and USB2.0 OTG)
- 1 USB 3.0 Host port
- 3 USB 2.0 Host ports
- 1 HDMI
- 1 infrared receiver
- 1 MIPI DSI
- 1 MIPI CSI
- 1 x 4-section headphone jack
- Mini PCIe socket (USB or PCIe)
- 1 SIM Card slot
- 1 SYS LED and 1 PWR LED
- 40-pin GPIO expansion header

Signed-off-by: Yuteng Zhong <zonyitoo@gmail.com>
Signed-off-by: DHDAXCW <lasstp5011@gmail.com>
---

Changed in V2:
  - Remove RNG node
Changed in V3:
  - Modify all node names

---
 .../devicetree/bindings/arm/rockchip.yaml     |   5 +
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../boot/dts/rockchip/rk3566-lubancat-1.dts   | 600 ++++++++++++++++++
 3 files changed, 606 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-lubancat-1.dts

Comments

Rob Herring Dec. 22, 2022, 5:25 p.m. UTC | #1
On Wed, Dec 21, 2022 at 01:43:07PM +0800, Yuteng Zhong wrote:
> LubanCat 1 is a Rockchip RK3566 SBC based
> is developed by EmbedFire Electronics Co., Ltd.
> Mini Linux Card Type Cheap Computer Development Board
> It has the following characteristics:
> - MicroSD card slot, onboard eMMC flash memory
> - 1GbE Realtek RTL8211F Ethernet Transceiver
> - 1 USB Type-C port (power and USB2.0 OTG)
> - 1 USB 3.0 Host port
> - 3 USB 2.0 Host ports
> - 1 HDMI
> - 1 infrared receiver
> - 1 MIPI DSI
> - 1 MIPI CSI
> - 1 x 4-section headphone jack
> - Mini PCIe socket (USB or PCIe)
> - 1 SIM Card slot
> - 1 SYS LED and 1 PWR LED
> - 40-pin GPIO expansion header
> 
> Signed-off-by: Yuteng Zhong <zonyitoo@gmail.com>
> Signed-off-by: DHDAXCW <lasstp5011@gmail.com>

DHDAXCW is a legal name?

The person sending the patch email should be last.

> ---
> 
> Changed in V2:
>   - Remove RNG node
> Changed in V3:
>   - Modify all node names
> 
> ---
>  .../devicetree/bindings/arm/rockchip.yaml     |   5 +

Bindings should be separate patch.

>  arch/arm64/boot/dts/rockchip/Makefile         |   1 +
>  .../boot/dts/rockchip/rk3566-lubancat-1.dts   | 600 ++++++++++++++++++

Fix all the whitespace errors checkpatch.pl complains about.
Heiko Stübner Dec. 22, 2022, 7:10 p.m. UTC | #2
Hi Rob,

Am Donnerstag, 22. Dezember 2022, 18:25:04 CET schrieb Rob Herring:
> On Wed, Dec 21, 2022 at 01:43:07PM +0800, Yuteng Zhong wrote:
> > LubanCat 1 is a Rockchip RK3566 SBC based
> > is developed by EmbedFire Electronics Co., Ltd.
> > Mini Linux Card Type Cheap Computer Development Board
> > It has the following characteristics:
> > - MicroSD card slot, onboard eMMC flash memory
> > - 1GbE Realtek RTL8211F Ethernet Transceiver
> > - 1 USB Type-C port (power and USB2.0 OTG)
> > - 1 USB 3.0 Host port
> > - 3 USB 2.0 Host ports
> > - 1 HDMI
> > - 1 infrared receiver
> > - 1 MIPI DSI
> > - 1 MIPI CSI
> > - 1 x 4-section headphone jack
> > - Mini PCIe socket (USB or PCIe)
> > - 1 SIM Card slot
> > - 1 SYS LED and 1 PWR LED
> > - 40-pin GPIO expansion header
> > 
> > Signed-off-by: Yuteng Zhong <zonyitoo@gmail.com>
> > Signed-off-by: DHDAXCW <lasstp5011@gmail.com>
> 
> DHDAXCW is a legal name?
> 
> The person sending the patch email should be last.

We're on v7 already [0] and at least the Authorship + separate binding
issue got fixed meanwhile - haven't looked at the whitespace issue there yet.


Heiko


[0] https://lore.kernel.org/all/Y6MlrbGKiIVc6tXt@VM-66-53-centos/

> > ---
> > 
> > Changed in V2:
> >   - Remove RNG node
> > Changed in V3:
> >   - Modify all node names
> > 
> > ---
> >  .../devicetree/bindings/arm/rockchip.yaml     |   5 +
> 
> Bindings should be separate patch.
> 
> >  arch/arm64/boot/dts/rockchip/Makefile         |   1 +
> >  .../boot/dts/rockchip/rk3566-lubancat-1.dts   | 600 ++++++++++++++++++
> 
> Fix all the whitespace errors checkpatch.pl complains about.
>
ty Dec. 23, 2022, 2:02 a.m. UTC | #3
Acknowledged. Fix will be in v8.

Heiko Stübner <heiko@sntech.de> 于2022年12月23日周五 03:10写道:
>
> Hi Rob,
>
> Am Donnerstag, 22. Dezember 2022, 18:25:04 CET schrieb Rob Herring:
> > On Wed, Dec 21, 2022 at 01:43:07PM +0800, Yuteng Zhong wrote:
> > > LubanCat 1 is a Rockchip RK3566 SBC based
> > > is developed by EmbedFire Electronics Co., Ltd.
> > > Mini Linux Card Type Cheap Computer Development Board
> > > It has the following characteristics:
> > > - MicroSD card slot, onboard eMMC flash memory
> > > - 1GbE Realtek RTL8211F Ethernet Transceiver
> > > - 1 USB Type-C port (power and USB2.0 OTG)
> > > - 1 USB 3.0 Host port
> > > - 3 USB 2.0 Host ports
> > > - 1 HDMI
> > > - 1 infrared receiver
> > > - 1 MIPI DSI
> > > - 1 MIPI CSI
> > > - 1 x 4-section headphone jack
> > > - Mini PCIe socket (USB or PCIe)
> > > - 1 SIM Card slot
> > > - 1 SYS LED and 1 PWR LED
> > > - 40-pin GPIO expansion header
> > >
> > > Signed-off-by: Yuteng Zhong <zonyitoo@gmail.com>
> > > Signed-off-by: DHDAXCW <lasstp5011@gmail.com>
> >
> > DHDAXCW is a legal name?
> >
> > The person sending the patch email should be last.
>
> We're on v7 already [0] and at least the Authorship + separate binding
> issue got fixed meanwhile - haven't looked at the whitespace issue there yet.
>
>
> Heiko
>
>
> [0] https://lore.kernel.org/all/Y6MlrbGKiIVc6tXt@VM-66-53-centos/
>
> > > ---
> > >
> > > Changed in V2:
> > >   - Remove RNG node
> > > Changed in V3:
> > >   - Modify all node names
> > >
> > > ---
> > >  .../devicetree/bindings/arm/rockchip.yaml     |   5 +
> >
> > Bindings should be separate patch.
> >
> > >  arch/arm64/boot/dts/rockchip/Makefile         |   1 +
> > >  .../boot/dts/rockchip/rk3566-lubancat-1.dts   | 600 ++++++++++++++++++
> >
> > Fix all the whitespace errors checkpatch.pl complains about.
> >
>
>
>
>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 88ff4422a8c1..84d39a3a8843 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -781,6 +781,11 @@  properties:
           - const: rockchip,rk3568-bpi-r2pro
           - const: rockchip,rk3568
 
+      - description: EmbedFire LubanCat 1
+        items:
+          - const: embedfire,lubancat-1
+          - const: rockchip,rk3566
+
 additionalProperties: true
 
 ...
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 0a76a2ebb5f6..e52bda04d45a 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -78,6 +78,7 @@  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-blade.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-cm4.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-model-a.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-box-demo.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-lubancat-1.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-bpi-r2-pro.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-odroid-m1.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-lubancat-1.dts b/arch/arm64/boot/dts/rockchip/rk3566-lubancat-1.dts
new file mode 100644
index 000000000000..af1abb38d45c
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-lubancat-1.dts
@@ -0,0 +1,600 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+* Copyright (c) 2021 Rockchip Electronics Co., Ltd.
+*/
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+	model = "EmbedFire LubanCat 1";
+	compatible = "embedfire,lubancat-1", "rockchip,rk3566";
+
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac1_clkin: external-gmac1-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac1_clkin";
+		#clock-cells = <0>;
+	};
+	
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		sys_led: sys-led {
+			label = "sys_led";
+			linux,default-trigger = "heartbeat";
+			default-state = "on";
+			gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&sys_led_pin>;
+		};
+	};
+
+	dc_5v: dc-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_5v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_5v>;
+	};
+
+	pcie_3v3: pcie2-3v3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb20_host: vcc5v0-usb20-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 RK_PB6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb20_host_en>;
+		regulator-name = "vcc5v0_usb20_host";
+		regulator-always-on;
+	};
+
+	vcc5v0_usb30_host: vcc5v0-usb30-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 RK_PB5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb30_host_en>;
+		regulator-name = "vcc5v0_usb30_host";
+		regulator-always-on;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&combphy1 {
+	status = "okay";
+};
+
+&combphy2 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+		#clock-cells = <1>;
+		clock-names = "mclk";
+		clocks = <&cru I2S1_MCLKOUT_TX>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>;
+		rockchip,system-power-controller;
+		#sound-dai-cells = <0>;
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+		wakeup-source;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-name = "vdd_npu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-name = "vdda0v9_image";
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-name = "vcca1v8_image";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2s1_8ch {
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+&gmac1 {
+    phy-mode = "rgmii";
+    clock_in_out = "output";
+    snps,reset-gpio = <&gpio2 RK_PB0 GPIO_ACTIVE_LOW>;
+    snps,reset-active-low;
+    /* Reset time is 100ms, 100ms */
+    snps,reset-delays-us = <0 75000 100000>;
+    assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+    assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
+    assigned-clock-rates = <0>, <125000000>;
+    pinctrl-names = "default";
+    pinctrl-0 = <&gmac1m1_miim
+             &gmac1m1_tx_bus2_level3
+             &gmac1m1_rx_bus2
+             &gmac1m1_rgmii_clk_level2
+             &gmac1m1_rgmii_bus_level3>;
+    tx_delay = <0x1a>;
+    rx_delay = <0x0c>; 
+    phy-handle = <&rgmii_phy1>;
+    status = "okay";
+};
+
+&mdio1 {
+    rgmii_phy1: phy@0 {
+        compatible = "ethernet-phy-ieee802.3-c22";
+        reg = <0x0>;
+    };
+};
+
+&pcie2x1 {
+    reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
+    disable-gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+    vpcie3v3-supply = <&pcie_3v3>;
+    status = "okay";
+};
+
+&pinctrl {
+	leds {
+		sys_led_pin: sys-status-led-pin {
+			rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+    usb {
+        vcc5v0_usb20_host_en: vcc5v0-usb20-host-en {
+            rockchip,pins = <2 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
+        };
+
+        vcc5v0_usb30_host_en: vcc5v0-usb30-host-en {
+            rockchip,pins = <2 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+        };
+    };
+
+	pmic {
+		pmic_int: pmic_int {
+			rockchip,pins =
+				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_3v3>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&sdhci {
+	assigned-clocks = <&cru BCLK_EMMC>, <&cru TCLK_EMMC>, <&cru CCLK_EMMC>;
+	assigned-clock-rates = <200000000>, <24000000>, <200000000>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	mmc-hs200-1_8v;		
+	non-removable;	
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>;	
+	supports-emmc;
+	status = "okay";
+};
+
+&sdmmc0 {
+    max-frequency = <150000000>;
+    supports-sd;
+    bus-width = <4>;
+    cap-mmc-highspeed;
+    cap-sd-highspeed;
+    disable-wp;
+    sd-uhs-sdr104;
+    vmmc-supply = <&vcc3v3_sd>;
+    vqmmc-supply = <&vccio_sd>;
+    pinctrl-names = "default";
+    pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+    status = "okay";
+};
+
+/* USB OTG/USB Host_1 USB 2.0 Comb */
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+/* USB Host_2/USB Host_3 USB 2.0 Comb */
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb2phy1_host {
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+/* USB3.0 Host */
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};