| Message ID | 20221227233020.284266-20-martin.blumenstingl@googlemail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | rtw88: Add SDIO support | expand |
On Wed, Dec 28, 2022 at 12:30:20AM +0100, Martin Blumenstingl wrote: > Wire up RTL8821CS chipset support using the new rtw88 SDIO HCI code as > well as the existing RTL8821C chipset code. > Unfortunately, this doesn't work for me. I applied it on top of 6.2-rc2 master and I get errors during probe (it appears the firmware never loads). Relevant dmesg logs are as follows: [ 0.989545] mmc2: new high speed SDIO card at address 0001 [ 0.989993] rtw_8821cs mmc2:0001:1: Firmware version 24.8.0, H2C version 12 [ 1.005684] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x14): -110 [ 1.005737] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1080): -110 [ 1.005789] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x11080): -110 [ 1.005840] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x3): -110 [ 1.005920] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x1103): -110 [ 1.005998] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x80): -110 [ 1.006078] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1700): -110 The error of "sdio read32 failed (0x1700): -110" then repeats several hundred times, then I get this: [ 1.066294] rtw_8821cs mmc2:0001:1: failed to download firmware [ 1.066367] rtw_8821cs mmc2:0001:1: sdio read16 failed (0x80): -110 [ 1.066417] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x100): -110 [ 1.066697] rtw_8821cs mmc2:0001:1: failed to setup chip efuse info [ 1.066703] rtw_8821cs mmc2:0001:1: failed to setup chip information [ 1.066839] rtw_8821cs: probe of mmc2:0001:1 failed with error -16 The hardware I am using is an rtl8821cs that I can confirm was working with a previous driver. Thank you. > Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> > --- > drivers/net/wireless/realtek/rtw88/Kconfig | 11 ++++++ > drivers/net/wireless/realtek/rtw88/Makefile | 3 ++ > .../net/wireless/realtek/rtw88/rtw8821cs.c | 34 +++++++++++++++++++ > 3 files changed, 48 insertions(+) > create mode 100644 drivers/net/wireless/realtek/rtw88/rtw8821cs.c > > diff --git a/drivers/net/wireless/realtek/rtw88/Kconfig b/drivers/net/wireless/realtek/rtw88/Kconfig > index 6b65da81127f..29eb2f8e0eb7 100644 > --- a/drivers/net/wireless/realtek/rtw88/Kconfig > +++ b/drivers/net/wireless/realtek/rtw88/Kconfig > @@ -133,6 +133,17 @@ config RTW88_8821CE > > 802.11ac PCIe wireless network adapter > > +config RTW88_8821CS > + tristate "Realtek 8821CS SDIO wireless network adapter" > + depends on MMC > + select RTW88_CORE > + select RTW88_SDIO > + select RTW88_8821C > + help > + Select this option will enable support for 8821CS chipset > + > + 802.11ac SDIO wireless network adapter > + > config RTW88_8821CU > tristate "Realtek 8821CU USB wireless network adapter" > depends on USB > diff --git a/drivers/net/wireless/realtek/rtw88/Makefile b/drivers/net/wireless/realtek/rtw88/Makefile > index 6105c2745bda..82979b30ae8d 100644 > --- a/drivers/net/wireless/realtek/rtw88/Makefile > +++ b/drivers/net/wireless/realtek/rtw88/Makefile > @@ -59,6 +59,9 @@ rtw88_8821c-objs := rtw8821c.o rtw8821c_table.o > obj-$(CONFIG_RTW88_8821CE) += rtw88_8821ce.o > rtw88_8821ce-objs := rtw8821ce.o > > +obj-$(CONFIG_RTW88_8821CS) += rtw88_8821cs.o > +rtw88_8821cs-objs := rtw8821cs.o > + > obj-$(CONFIG_RTW88_8821CU) += rtw88_8821cu.o > rtw88_8821cu-objs := rtw8821cu.o > > diff --git a/drivers/net/wireless/realtek/rtw88/rtw8821cs.c b/drivers/net/wireless/realtek/rtw88/rtw8821cs.c > new file mode 100644 > index 000000000000..61f82b38cda4 > --- /dev/null > +++ b/drivers/net/wireless/realtek/rtw88/rtw8821cs.c > @@ -0,0 +1,34 @@ > +// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause > +// Copyright(c) Martin Blumenstingl <martin.blumenstingl@googlemail.com> > + > +#include <linux/mmc/sdio_func.h> > +#include <linux/mmc/sdio_ids.h> > +#include <linux/module.h> > +#include "sdio.h" > +#include "rtw8821c.h" > + > +static const struct sdio_device_id rtw_8821cs_id_table[] = { > + { > + SDIO_DEVICE(SDIO_VENDOR_ID_REALTEK, > + SDIO_DEVICE_ID_REALTEK_RTW8821CS), > + .driver_data = (kernel_ulong_t)&rtw8821c_hw_spec, > + }, > + {} > +}; > +MODULE_DEVICE_TABLE(sdio, rtw_8821cs_id_table); > + > +static struct sdio_driver rtw_8821cs_driver = { > + .name = "rtw_8821cs", > + .probe = rtw_sdio_probe, > + .remove = rtw_sdio_remove, > + .id_table = rtw_8821cs_id_table, > + .drv = { > + .pm = &rtw_sdio_pm_ops, > + .shutdown = rtw_sdio_shutdown, > + } > +}; > +module_sdio_driver(rtw_8821cs_driver); > + > +MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>"); > +MODULE_DESCRIPTION("Realtek 802.11ac wireless 8821cs driver"); > +MODULE_LICENSE("Dual BSD/GPL"); > -- > 2.39.0 >
Hi Chris, On Wed, Jan 4, 2023 at 12:01 AM Chris Morgan <macroalpha82@gmail.com> wrote: > > On Wed, Dec 28, 2022 at 12:30:20AM +0100, Martin Blumenstingl wrote: > > Wire up RTL8821CS chipset support using the new rtw88 SDIO HCI code as > > well as the existing RTL8821C chipset code. > > > > Unfortunately, this doesn't work for me. I applied it on top of 6.2-rc2 > master and I get errors during probe (it appears the firmware never > loads). That's unfortunate. > Relevant dmesg logs are as follows: > > [ 0.989545] mmc2: new high speed SDIO card at address 0001 > [ 0.989993] rtw_8821cs mmc2:0001:1: Firmware version 24.8.0, H2C version 12 > [ 1.005684] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x14): -110 > [ 1.005737] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1080): -110 > [ 1.005789] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x11080): -110 > [ 1.005840] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x3): -110 > [ 1.005920] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x1103): -110 > [ 1.005998] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x80): -110 > [ 1.006078] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1700): -110 The error starts with a write to register 0x14 (REG_SDIO_HIMR), which happens right after configuring RX aggregation. Can you please try two modifications inside drivers/net/wireless/realtek/rtw88/sdio.c: 1. inside the rtw_sdio_start() function: change "rtw_sdio_rx_aggregation(rtwdev, false);" to "rtw_sdio_rx_aggregation(rtwdev, true);" 2. if 1) does not work: remove the call to rtw_sdio_rx_aggregation() from rtw_sdio_start() Best regards, Martin
On Wed, Jan 04, 2023 at 04:40:51PM +0100, Martin Blumenstingl wrote: > Hi Chris, > > On Wed, Jan 4, 2023 at 12:01 AM Chris Morgan <macroalpha82@gmail.com> wrote: > > > > On Wed, Dec 28, 2022 at 12:30:20AM +0100, Martin Blumenstingl wrote: > > > Wire up RTL8821CS chipset support using the new rtw88 SDIO HCI code as > > > well as the existing RTL8821C chipset code. > > > > > > > Unfortunately, this doesn't work for me. I applied it on top of 6.2-rc2 > > master and I get errors during probe (it appears the firmware never > > loads). > That's unfortunate. > > > Relevant dmesg logs are as follows: > > > > [ 0.989545] mmc2: new high speed SDIO card at address 0001 > > [ 0.989993] rtw_8821cs mmc2:0001:1: Firmware version 24.8.0, H2C version 12 > > [ 1.005684] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x14): -110 > > [ 1.005737] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1080): -110 > > [ 1.005789] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x11080): -110 > > [ 1.005840] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x3): -110 > > [ 1.005920] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x1103): -110 > > [ 1.005998] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x80): -110 > > [ 1.006078] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1700): -110 > The error starts with a write to register 0x14 (REG_SDIO_HIMR), which > happens right after configuring RX aggregation. > Can you please try two modifications inside > drivers/net/wireless/realtek/rtw88/sdio.c: > 1. inside the rtw_sdio_start() function: change > "rtw_sdio_rx_aggregation(rtwdev, false);" to > "rtw_sdio_rx_aggregation(rtwdev, true);" No change, still receive identical issue. > 2. if 1) does not work: remove the call to rtw_sdio_rx_aggregation() > from rtw_sdio_start() > Same here, still receive identical issue. > > Best regards, > Martin
On Wed, Jan 4, 2023 at 6:05 PM Chris Morgan <macroalpha82@gmail.com> wrote: [...] > > > [ 0.989545] mmc2: new high speed SDIO card at address 0001 > > > [ 0.989993] rtw_8821cs mmc2:0001:1: Firmware version 24.8.0, H2C version 12 > > > [ 1.005684] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x14): -110 > > > [ 1.005737] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1080): -110 > > > [ 1.005789] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x11080): -110 > > > [ 1.005840] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x3): -110 > > > [ 1.005920] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x1103): -110 > > > [ 1.005998] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x80): -110 > > > [ 1.006078] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1700): -110 > > The error starts with a write to register 0x14 (REG_SDIO_HIMR), which > > happens right after configuring RX aggregation. > > Can you please try two modifications inside > > drivers/net/wireless/realtek/rtw88/sdio.c: > > 1. inside the rtw_sdio_start() function: change > > "rtw_sdio_rx_aggregation(rtwdev, false);" to > > "rtw_sdio_rx_aggregation(rtwdev, true);" > > No change, still receive identical issue. > > > 2. if 1) does not work: remove the call to rtw_sdio_rx_aggregation() > > from rtw_sdio_start() > > > > Same here, still receive identical issue. Thanks for testing and for reporting back! Looking back at it again: I think I mis-interpreted your error output. I think it's actually failing in __rtw_mac_init_system_cfg() Can you please try the latest code from [0] (ignoring any changes I recommended previously)? There's two bug fixes in there (compared to this series) which may solve the issue that you are seeing: - fix typos to use "if (!*err_ret ..." (to read the error code) instead of "if (!err_ret ..." (which just checks if a non-null pointer was passed) in rtw_sdio_read_indirect{8,32} - change buf[0] to buf[i] in rtw_sdio_read_indirect_bytes These fixes will be part of v2 of this series anyways. Best regards, Martin [0] https://github.com/xdarklight/linux/tree/d115a8631d208996510822f0805df5dfc8dfb548
On 04/01/2023 01:01, Chris Morgan wrote: > On Wed, Dec 28, 2022 at 12:30:20AM +0100, Martin Blumenstingl wrote: >> Wire up RTL8821CS chipset support using the new rtw88 SDIO HCI code as >> well as the existing RTL8821C chipset code. >> > > Unfortunately, this doesn't work for me. I applied it on top of 6.2-rc2 > master and I get errors during probe (it appears the firmware never > loads). > > Relevant dmesg logs are as follows: > > [ 0.989545] mmc2: new high speed SDIO card at address 0001 > [ 0.989993] rtw_8821cs mmc2:0001:1: Firmware version 24.8.0, H2C version 12 > [ 1.005684] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x14): -110 > [ 1.005737] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1080): -110 > [ 1.005789] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x11080): -110 > [ 1.005840] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x3): -110 > [ 1.005920] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x1103): -110 > [ 1.005998] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x80): -110 > [ 1.006078] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1700): -110 > > The error of "sdio read32 failed (0x1700): -110" then repeats several > hundred times, then I get this: > > [ 1.066294] rtw_8821cs mmc2:0001:1: failed to download firmware > [ 1.066367] rtw_8821cs mmc2:0001:1: sdio read16 failed (0x80): -110 > [ 1.066417] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x100): -110 > [ 1.066697] rtw_8821cs mmc2:0001:1: failed to setup chip efuse info > [ 1.066703] rtw_8821cs mmc2:0001:1: failed to setup chip information > [ 1.066839] rtw_8821cs: probe of mmc2:0001:1 failed with error -16 > > The hardware I am using is an rtl8821cs that I can confirm was working > with a previous driver. > > Thank you. > The USB-based RTL8811CU also doesn't work, with suspiciously similar errors: Dec 25 21:43:37 home kernel: rtw_8821cu 1-2:1.0: Firmware version 24.11.0, H2C version 12 Dec 25 21:43:37 home kernel: rtw_8821cu 1-2:1.0 wlp0s20f0u2: renamed from wlan0 Dec 25 21:43:40 home kernel: rtw_8821cu 1-2:1.0: read register 0x5 failed with -110 Dec 25 21:43:41 home kernel: rtw_8821cu 1-2:1.0: read register 0x20 failed with -110 Dec 25 21:44:11 home kernel: rtw_8821cu 1-2:1.0: write register 0x20 failed with -110 Dec 25 21:44:12 home kernel: rtw_8821cu 1-2:1.0: read register 0x7c failed with -110 Dec 25 21:44:43 home kernel: rtw_8821cu 1-2:1.0: write register 0x7c failed with -110 Dec 25 21:44:44 home kernel: rtw_8821cu 1-2:1.0: read register 0x1080 failed with -110 Dec 25 21:45:16 home kernel: rtw_8821cu 1-2:1.0: write register 0x1080 failed with -110 Dec 25 21:46:47 home kernel: rtw_8821cu 1-3:1.0: Firmware version 24.11.0, H2C version 12 Dec 25 21:46:47 home kernel: rtw_8821cu 1-3:1.0 wlp0s20f0u3: renamed from wlan0 Dec 25 21:46:55 home kernel: rtw_8821cu 1-3:1.0: failed to poll offset=0x5 mask=0x1 value=0x0 Dec 25 21:46:55 home kernel: rtw_8821cu 1-3:1.0: mac power on failed Dec 25 21:46:55 home kernel: rtw_8821cu 1-3:1.0: failed to power on mac I tested with https://github.com/lwfinger/rtw88/ which should have the same code as wireless-next currently.
Am 04.01.23 um 20:59 schrieb Bitterblue Smith: > The USB-based RTL8811CU also doesn't work, with suspiciously similar > errors: > > Dec 25 21:43:37 home kernel: rtw_8821cu 1-2:1.0: Firmware version 24.11.0, H2C version 12 > Dec 25 21:43:37 home kernel: rtw_8821cu 1-2:1.0 wlp0s20f0u2: renamed from wlan0 > Dec 25 21:43:40 home kernel: rtw_8821cu 1-2:1.0: read register 0x5 failed with -110 > Dec 25 21:43:41 home kernel: rtw_8821cu 1-2:1.0: read register 0x20 failed with -110 > Dec 25 21:44:11 home kernel: rtw_8821cu 1-2:1.0: write register 0x20 failed with -110 > Dec 25 21:44:12 home kernel: rtw_8821cu 1-2:1.0: read register 0x7c failed with -110 > Dec 25 21:44:43 home kernel: rtw_8821cu 1-2:1.0: write register 0x7c failed with -110 > Dec 25 21:44:44 home kernel: rtw_8821cu 1-2:1.0: read register 0x1080 failed with -110 > Dec 25 21:45:16 home kernel: rtw_8821cu 1-2:1.0: write register 0x1080 failed with -110 Same for me: I saw very similar read/write failures with my "Realtek Semiconductor Corp. 802.11ac NIC" (ID 0bda:c811) after applying Ping-Ke's patch for rfe 38 (see my message to linux-wireless on Dec 29). Felix
On 1/4/23 13:59, Bitterblue Smith wrote: > I tested with https://github.com/lwfinger/rtw88/ which should have the > same code as wireless-next currently. I just rechecked. My repo was missing some changes from wireless-next. It now matches. Larry
On Wed, Jan 04, 2023 at 06:23:24PM +0100, Martin Blumenstingl wrote: > On Wed, Jan 4, 2023 at 6:05 PM Chris Morgan <macroalpha82@gmail.com> wrote: > [...] > > > > [ 0.989545] mmc2: new high speed SDIO card at address 0001 > > > > [ 0.989993] rtw_8821cs mmc2:0001:1: Firmware version 24.8.0, H2C version 12 > > > > [ 1.005684] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x14): -110 > > > > [ 1.005737] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1080): -110 > > > > [ 1.005789] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x11080): -110 > > > > [ 1.005840] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x3): -110 > > > > [ 1.005920] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x1103): -110 > > > > [ 1.005998] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x80): -110 > > > > [ 1.006078] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1700): -110 > > > The error starts with a write to register 0x14 (REG_SDIO_HIMR), which > > > happens right after configuring RX aggregation. > > > Can you please try two modifications inside > > > drivers/net/wireless/realtek/rtw88/sdio.c: > > > 1. inside the rtw_sdio_start() function: change > > > "rtw_sdio_rx_aggregation(rtwdev, false);" to > > > "rtw_sdio_rx_aggregation(rtwdev, true);" > > > > No change, still receive identical issue. > > > > > 2. if 1) does not work: remove the call to rtw_sdio_rx_aggregation() > > > from rtw_sdio_start() > > > > > > > Same here, still receive identical issue. > Thanks for testing and for reporting back! > > Looking back at it again: I think I mis-interpreted your error output. > I think it's actually failing in __rtw_mac_init_system_cfg() > > Can you please try the latest code from [0] (ignoring any changes I > recommended previously)? > There's two bug fixes in there (compared to this series) which may > solve the issue that you are seeing: > - fix typos to use "if (!*err_ret ..." (to read the error code) > instead of "if (!err_ret ..." (which just checks if a non-null pointer > was passed) in rtw_sdio_read_indirect{8,32} > - change buf[0] to buf[i] in rtw_sdio_read_indirect_bytes > > These fixes will be part of v2 of this series anyways. That still doesn't fix it, I receive the same error. I'm using an older patch series of yours (that I can't seem to find on github anymore), so I'll see if I can compare the older series that works with this one and find out the root cause. Thank you. > > > Best regards, > Martin > > > [0] https://github.com/xdarklight/linux/tree/d115a8631d208996510822f0805df5dfc8dfb548
On Wed, Jan 04, 2023 at 09:59:35PM +0200, Bitterblue Smith wrote: > On 04/01/2023 01:01, Chris Morgan wrote: > > On Wed, Dec 28, 2022 at 12:30:20AM +0100, Martin Blumenstingl wrote: > >> Wire up RTL8821CS chipset support using the new rtw88 SDIO HCI code as > >> well as the existing RTL8821C chipset code. > >> > > > > Unfortunately, this doesn't work for me. I applied it on top of 6.2-rc2 > > master and I get errors during probe (it appears the firmware never > > loads). > > > > Relevant dmesg logs are as follows: > > > > [ 0.989545] mmc2: new high speed SDIO card at address 0001 > > [ 0.989993] rtw_8821cs mmc2:0001:1: Firmware version 24.8.0, H2C version 12 > > [ 1.005684] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x14): -110 > > [ 1.005737] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1080): -110 > > [ 1.005789] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x11080): -110 > > [ 1.005840] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x3): -110 > > [ 1.005920] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x1103): -110 > > [ 1.005998] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x80): -110 > > [ 1.006078] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1700): -110 > > > > The error of "sdio read32 failed (0x1700): -110" then repeats several > > hundred times, then I get this: > > > > [ 1.066294] rtw_8821cs mmc2:0001:1: failed to download firmware > > [ 1.066367] rtw_8821cs mmc2:0001:1: sdio read16 failed (0x80): -110 > > [ 1.066417] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x100): -110 > > [ 1.066697] rtw_8821cs mmc2:0001:1: failed to setup chip efuse info > > [ 1.066703] rtw_8821cs mmc2:0001:1: failed to setup chip information > > [ 1.066839] rtw_8821cs: probe of mmc2:0001:1 failed with error -16 > > > > The hardware I am using is an rtl8821cs that I can confirm was working > > with a previous driver. > > > > Thank you. > > > The USB-based RTL8811CU also doesn't work, with suspiciously similar > errors: > > Dec 25 21:43:37 home kernel: rtw_8821cu 1-2:1.0: Firmware version 24.11.0, H2C version 12 > Dec 25 21:43:37 home kernel: rtw_8821cu 1-2:1.0 wlp0s20f0u2: renamed from wlan0 > Dec 25 21:43:40 home kernel: rtw_8821cu 1-2:1.0: read register 0x5 failed with -110 Is this the very first register access or are there other register accesses before that actually do work? Sascha
On 05/01/2023 10:01, Sascha Hauer wrote: > On Wed, Jan 04, 2023 at 09:59:35PM +0200, Bitterblue Smith wrote: >> On 04/01/2023 01:01, Chris Morgan wrote: >>> On Wed, Dec 28, 2022 at 12:30:20AM +0100, Martin Blumenstingl wrote: >>>> Wire up RTL8821CS chipset support using the new rtw88 SDIO HCI code as >>>> well as the existing RTL8821C chipset code. >>>> >>> >>> Unfortunately, this doesn't work for me. I applied it on top of 6.2-rc2 >>> master and I get errors during probe (it appears the firmware never >>> loads). >>> >>> Relevant dmesg logs are as follows: >>> >>> [ 0.989545] mmc2: new high speed SDIO card at address 0001 >>> [ 0.989993] rtw_8821cs mmc2:0001:1: Firmware version 24.8.0, H2C version 12 >>> [ 1.005684] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x14): -110 >>> [ 1.005737] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1080): -110 >>> [ 1.005789] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x11080): -110 >>> [ 1.005840] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x3): -110 >>> [ 1.005920] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x1103): -110 >>> [ 1.005998] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x80): -110 >>> [ 1.006078] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1700): -110 >>> >>> The error of "sdio read32 failed (0x1700): -110" then repeats several >>> hundred times, then I get this: >>> >>> [ 1.066294] rtw_8821cs mmc2:0001:1: failed to download firmware >>> [ 1.066367] rtw_8821cs mmc2:0001:1: sdio read16 failed (0x80): -110 >>> [ 1.066417] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x100): -110 >>> [ 1.066697] rtw_8821cs mmc2:0001:1: failed to setup chip efuse info >>> [ 1.066703] rtw_8821cs mmc2:0001:1: failed to setup chip information >>> [ 1.066839] rtw_8821cs: probe of mmc2:0001:1 failed with error -16 >>> >>> The hardware I am using is an rtl8821cs that I can confirm was working >>> with a previous driver. >>> >>> Thank you. >>> >> The USB-based RTL8811CU also doesn't work, with suspiciously similar >> errors: >> >> Dec 25 21:43:37 home kernel: rtw_8821cu 1-2:1.0: Firmware version 24.11.0, H2C version 12 >> Dec 25 21:43:37 home kernel: rtw_8821cu 1-2:1.0 wlp0s20f0u2: renamed from wlan0 >> Dec 25 21:43:40 home kernel: rtw_8821cu 1-2:1.0: read register 0x5 failed with -110 > > Is this the very first register access or are there other register > accesses before that actually do work? > > Sascha > It's not the first register access. rtw_mac_power_switch() runs a few times before things fail.
On 04/01/2023 22:14, Larry Finger wrote: > On 1/4/23 13:59, Bitterblue Smith wrote: >> I tested with https://github.com/lwfinger/rtw88/ which should have the >> same code as wireless-next currently. > > I just rechecked. My repo was missing some changes from wireless-next. It now matches. > > Larry > > Did you mean to push some commits? The latest one is still from December.
diff --git a/drivers/net/wireless/realtek/rtw88/Kconfig b/drivers/net/wireless/realtek/rtw88/Kconfig index 6b65da81127f..29eb2f8e0eb7 100644 --- a/drivers/net/wireless/realtek/rtw88/Kconfig +++ b/drivers/net/wireless/realtek/rtw88/Kconfig @@ -133,6 +133,17 @@ config RTW88_8821CE 802.11ac PCIe wireless network adapter +config RTW88_8821CS + tristate "Realtek 8821CS SDIO wireless network adapter" + depends on MMC + select RTW88_CORE + select RTW88_SDIO + select RTW88_8821C + help + Select this option will enable support for 8821CS chipset + + 802.11ac SDIO wireless network adapter + config RTW88_8821CU tristate "Realtek 8821CU USB wireless network adapter" depends on USB diff --git a/drivers/net/wireless/realtek/rtw88/Makefile b/drivers/net/wireless/realtek/rtw88/Makefile index 6105c2745bda..82979b30ae8d 100644 --- a/drivers/net/wireless/realtek/rtw88/Makefile +++ b/drivers/net/wireless/realtek/rtw88/Makefile @@ -59,6 +59,9 @@ rtw88_8821c-objs := rtw8821c.o rtw8821c_table.o obj-$(CONFIG_RTW88_8821CE) += rtw88_8821ce.o rtw88_8821ce-objs := rtw8821ce.o +obj-$(CONFIG_RTW88_8821CS) += rtw88_8821cs.o +rtw88_8821cs-objs := rtw8821cs.o + obj-$(CONFIG_RTW88_8821CU) += rtw88_8821cu.o rtw88_8821cu-objs := rtw8821cu.o diff --git a/drivers/net/wireless/realtek/rtw88/rtw8821cs.c b/drivers/net/wireless/realtek/rtw88/rtw8821cs.c new file mode 100644 index 000000000000..61f82b38cda4 --- /dev/null +++ b/drivers/net/wireless/realtek/rtw88/rtw8821cs.c @@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause +// Copyright(c) Martin Blumenstingl <martin.blumenstingl@googlemail.com> + +#include <linux/mmc/sdio_func.h> +#include <linux/mmc/sdio_ids.h> +#include <linux/module.h> +#include "sdio.h" +#include "rtw8821c.h" + +static const struct sdio_device_id rtw_8821cs_id_table[] = { + { + SDIO_DEVICE(SDIO_VENDOR_ID_REALTEK, + SDIO_DEVICE_ID_REALTEK_RTW8821CS), + .driver_data = (kernel_ulong_t)&rtw8821c_hw_spec, + }, + {} +}; +MODULE_DEVICE_TABLE(sdio, rtw_8821cs_id_table); + +static struct sdio_driver rtw_8821cs_driver = { + .name = "rtw_8821cs", + .probe = rtw_sdio_probe, + .remove = rtw_sdio_remove, + .id_table = rtw_8821cs_id_table, + .drv = { + .pm = &rtw_sdio_pm_ops, + .shutdown = rtw_sdio_shutdown, + } +}; +module_sdio_driver(rtw_8821cs_driver); + +MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>"); +MODULE_DESCRIPTION("Realtek 802.11ac wireless 8821cs driver"); +MODULE_LICENSE("Dual BSD/GPL");
Wire up RTL8821CS chipset support using the new rtw88 SDIO HCI code as well as the existing RTL8821C chipset code. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> --- drivers/net/wireless/realtek/rtw88/Kconfig | 11 ++++++ drivers/net/wireless/realtek/rtw88/Makefile | 3 ++ .../net/wireless/realtek/rtw88/rtw8821cs.c | 34 +++++++++++++++++++ 3 files changed, 48 insertions(+) create mode 100644 drivers/net/wireless/realtek/rtw88/rtw8821cs.c