| Message ID | 20230113143647.14961-7-quic_devipriy@quicinc.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add APSS clock controller support for IPQ9574 | expand |
On 13.01.2023 15:36, devi priya wrote: > Included CLK_IS_CRITICAL flag which helps to properly enable > the APSS PLL during bootup. Please describe the issue and not only the user-visible impact it makes. Does the PLL get shut down by clk_ignore_unused? Maybe you would be interested in the sync_state changes that landed in recent -next that may solve it for you? I don't think it should be always-on, as you have an alternate source for low power modes, adding CLK_IS_CRITICAL will keep the PLL enabled even if you're not using it. > clk_rcg2_ops should be used for APSS clock RCG, as other ops > will not configure the RCG register RCG register meaning RCG register*s*, meaning in this case M/N/D which would be required for proper rate setting and not only input switching (which arguably doesn't seem to be of much concern on a single-parent clock)? This all is not obvious.. Konrad > > Co-developed-by: Praveenkumar I <quic_ipkumar@quicinc.com> > Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com> > Signed-off-by: devi priya <quic_devipriy@quicinc.com> > --- > drivers/clk/qcom/apss-ipq-pll.c | 1 + > drivers/clk/qcom/apss-ipq6018.c | 8 +++++++- > 2 files changed, 8 insertions(+), 1 deletion(-) > > diff --git a/drivers/clk/qcom/apss-ipq-pll.c b/drivers/clk/qcom/apss-ipq-pll.c > index dd0c01bf5a98..75486a124fcd 100644 > --- a/drivers/clk/qcom/apss-ipq-pll.c > +++ b/drivers/clk/qcom/apss-ipq-pll.c > @@ -33,6 +33,7 @@ static struct clk_alpha_pll ipq_pll = { > }, > .num_parents = 1, > .ops = &clk_alpha_pll_huayra_ops, > + .flags = CLK_IS_CRITICAL, > }, > }, > }; > diff --git a/drivers/clk/qcom/apss-ipq6018.c b/drivers/clk/qcom/apss-ipq6018.c > index f2f502e2d5a4..0d0e7196a4dc 100644 > --- a/drivers/clk/qcom/apss-ipq6018.c > +++ b/drivers/clk/qcom/apss-ipq6018.c > @@ -33,15 +33,21 @@ static const struct parent_map parents_apcs_alias0_clk_src_map[] = { > { P_APSS_PLL_EARLY, 5 }, > }; > > +static const struct freq_tbl ftbl_apcs_alias0_clk_src[] = { > + { .src = P_APSS_PLL_EARLY, .pre_div = 1 }, > + { } > +}; > + > static struct clk_rcg2 apcs_alias0_clk_src = { > .cmd_rcgr = 0x0050, > + .freq_tbl = ftbl_apcs_alias0_clk_src, > .hid_width = 5, > .parent_map = parents_apcs_alias0_clk_src_map, > .clkr.hw.init = &(struct clk_init_data){ > .name = "apcs_alias0_clk_src", > .parent_data = parents_apcs_alias0_clk_src, > .num_parents = ARRAY_SIZE(parents_apcs_alias0_clk_src), > - .ops = &clk_rcg2_mux_closest_ops, > + .ops = &clk_rcg2_ops, > .flags = CLK_SET_RATE_PARENT, > }, > };
On 13. 01. 2023. 16:20, Konrad Dybcio wrote: > > On 13.01.2023 15:36, devi priya wrote: >> Included CLK_IS_CRITICAL flag which helps to properly enable >> the APSS PLL during bootup. > Please describe the issue and not only the user-visible impact it > makes. Does the PLL get shut down by clk_ignore_unused? Maybe you > would be interested in the sync_state changes that landed in recent > -next that may solve it for you? > > I don't think it should be always-on, as you have an alternate source > for low power modes, adding CLK_IS_CRITICAL will keep the PLL enabled > even if you're not using it. I have the same opinion, as this is working fine on IPQ6018 and IPQ8074 and I have not experienced any issues with it. > >> clk_rcg2_ops should be used for APSS clock RCG, as other ops >> will not configure the RCG register > RCG register meaning RCG register*s*, meaning in this case M/N/D > which would be required for proper rate setting and not only input > switching (which arguably doesn't seem to be of much concern on a > single-parent clock)? This all is not obvious.. Same question from me as well, why do you need clk_rcg2_ops with a dummy frequency table since this is just a mux using RCG2 control bits? Regards, Robert > > Konrad >> Co-developed-by: Praveenkumar I <quic_ipkumar@quicinc.com> >> Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com> >> Signed-off-by: devi priya <quic_devipriy@quicinc.com> >> --- >> drivers/clk/qcom/apss-ipq-pll.c | 1 + >> drivers/clk/qcom/apss-ipq6018.c | 8 +++++++- >> 2 files changed, 8 insertions(+), 1 deletion(-) >> >> diff --git a/drivers/clk/qcom/apss-ipq-pll.c b/drivers/clk/qcom/apss-ipq-pll.c >> index dd0c01bf5a98..75486a124fcd 100644 >> --- a/drivers/clk/qcom/apss-ipq-pll.c >> +++ b/drivers/clk/qcom/apss-ipq-pll.c >> @@ -33,6 +33,7 @@ static struct clk_alpha_pll ipq_pll = { >> }, >> .num_parents = 1, >> .ops = &clk_alpha_pll_huayra_ops, >> + .flags = CLK_IS_CRITICAL, >> }, >> }, >> }; >> diff --git a/drivers/clk/qcom/apss-ipq6018.c b/drivers/clk/qcom/apss-ipq6018.c >> index f2f502e2d5a4..0d0e7196a4dc 100644 >> --- a/drivers/clk/qcom/apss-ipq6018.c >> +++ b/drivers/clk/qcom/apss-ipq6018.c >> @@ -33,15 +33,21 @@ static const struct parent_map parents_apcs_alias0_clk_src_map[] = { >> { P_APSS_PLL_EARLY, 5 }, >> }; >> >> +static const struct freq_tbl ftbl_apcs_alias0_clk_src[] = { >> + { .src = P_APSS_PLL_EARLY, .pre_div = 1 }, >> + { } >> +}; >> + >> static struct clk_rcg2 apcs_alias0_clk_src = { >> .cmd_rcgr = 0x0050, >> + .freq_tbl = ftbl_apcs_alias0_clk_src, >> .hid_width = 5, >> .parent_map = parents_apcs_alias0_clk_src_map, >> .clkr.hw.init = &(struct clk_init_data){ >> .name = "apcs_alias0_clk_src", >> .parent_data = parents_apcs_alias0_clk_src, >> .num_parents = ARRAY_SIZE(parents_apcs_alias0_clk_src), >> - .ops = &clk_rcg2_mux_closest_ops, >> + .ops = &clk_rcg2_ops, >> .flags = CLK_SET_RATE_PARENT, >> }, >> }; >
Thanks for taking time to review the patch On 1/13/2023 8:50 PM, Konrad Dybcio wrote: > > > On 13.01.2023 15:36, devi priya wrote: >> Included CLK_IS_CRITICAL flag which helps to properly enable >> the APSS PLL during bootup. > Please describe the issue and not only the user-visible impact it > makes. Does the PLL get shut down by clk_ignore_unused? Maybe you > would be interested in the sync_state changes that landed in recent > -next that may solve it for you? > > I don't think it should be always-on, as you have an alternate source > for low power modes, adding CLK_IS_CRITICAL will keep the PLL enabled > even if you're not using it. Yeah, got it. Will drop the critical flag > >> clk_rcg2_ops should be used for APSS clock RCG, as other ops >> will not configure the RCG register > RCG register meaning RCG register*s*, meaning in this case M/N/D > which would be required for proper rate setting and not only input > switching (which arguably doesn't seem to be of much concern on a > single-parent clock)? This all is not obvious.. > > Konrad The source selection is done by configuring the RCGR config register with the source entry (P_APSS_PLL_EARLY) added to the frequency table. Proper rate is achieved by configuring the PLL and hence M/N/D values are not configured >> >> Co-developed-by: Praveenkumar I <quic_ipkumar@quicinc.com> >> Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com> >> Signed-off-by: devi priya <quic_devipriy@quicinc.com> >> --- >> drivers/clk/qcom/apss-ipq-pll.c | 1 + >> drivers/clk/qcom/apss-ipq6018.c | 8 +++++++- >> 2 files changed, 8 insertions(+), 1 deletion(-) >> >> diff --git a/drivers/clk/qcom/apss-ipq-pll.c b/drivers/clk/qcom/apss-ipq-pll.c >> index dd0c01bf5a98..75486a124fcd 100644 >> --- a/drivers/clk/qcom/apss-ipq-pll.c >> +++ b/drivers/clk/qcom/apss-ipq-pll.c >> @@ -33,6 +33,7 @@ static struct clk_alpha_pll ipq_pll = { >> }, >> .num_parents = 1, >> .ops = &clk_alpha_pll_huayra_ops, >> + .flags = CLK_IS_CRITICAL, >> }, >> }, >> }; >> diff --git a/drivers/clk/qcom/apss-ipq6018.c b/drivers/clk/qcom/apss-ipq6018.c >> index f2f502e2d5a4..0d0e7196a4dc 100644 >> --- a/drivers/clk/qcom/apss-ipq6018.c >> +++ b/drivers/clk/qcom/apss-ipq6018.c >> @@ -33,15 +33,21 @@ static const struct parent_map parents_apcs_alias0_clk_src_map[] = { >> { P_APSS_PLL_EARLY, 5 }, >> }; >> >> +static const struct freq_tbl ftbl_apcs_alias0_clk_src[] = { >> + { .src = P_APSS_PLL_EARLY, .pre_div = 1 }, >> + { } >> +}; >> + >> static struct clk_rcg2 apcs_alias0_clk_src = { >> .cmd_rcgr = 0x0050, >> + .freq_tbl = ftbl_apcs_alias0_clk_src, >> .hid_width = 5, >> .parent_map = parents_apcs_alias0_clk_src_map, >> .clkr.hw.init = &(struct clk_init_data){ >> .name = "apcs_alias0_clk_src", >> .parent_data = parents_apcs_alias0_clk_src, >> .num_parents = ARRAY_SIZE(parents_apcs_alias0_clk_src), >> - .ops = &clk_rcg2_mux_closest_ops, >> + .ops = &clk_rcg2_ops, >> .flags = CLK_SET_RATE_PARENT, >> }, >> }; Best Regards, Devi Priya
Thanks for taking time to review the patch! On 1/13/2023 9:47 PM, Robert Marko wrote: > > On 13. 01. 2023. 16:20, Konrad Dybcio wrote: >> >> On 13.01.2023 15:36, devi priya wrote: >>> Included CLK_IS_CRITICAL flag which helps to properly enable >>> the APSS PLL during bootup. >> Please describe the issue and not only the user-visible impact it >> makes. Does the PLL get shut down by clk_ignore_unused? Maybe you >> would be interested in the sync_state changes that landed in recent >> -next that may solve it for you? >> >> I don't think it should be always-on, as you have an alternate source >> for low power modes, adding CLK_IS_CRITICAL will keep the PLL enabled >> even if you're not using it. > > I have the same opinion, as this is working fine on IPQ6018 and IPQ8074 > and I have not experienced any issues with it. > Sure, will drop the critical flag >> >>> clk_rcg2_ops should be used for APSS clock RCG, as other ops >>> will not configure the RCG register >> RCG register meaning RCG register*s*, meaning in this case M/N/D >> which would be required for proper rate setting and not only input >> switching (which arguably doesn't seem to be of much concern on a >> single-parent clock)? This all is not obvious.. > Same question from me as well, why do you need clk_rcg2_ops with > a dummy frequency table since this is just a mux using RCG2 control > bits? > > Regards, > Robert >> The RCGR is used for source selection whereas the rate setting is done by configuring the PLL. The source is configured in the RCGR using the source entry (P_APSS_PLL_EARLY) added to the frequency table. >> Konrad >>> Co-developed-by: Praveenkumar I <quic_ipkumar@quicinc.com> >>> Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com> >>> Signed-off-by: devi priya <quic_devipriy@quicinc.com> >>> --- >>> drivers/clk/qcom/apss-ipq-pll.c | 1 + >>> drivers/clk/qcom/apss-ipq6018.c | 8 +++++++- >>> 2 files changed, 8 insertions(+), 1 deletion(-) >>> >>> diff --git a/drivers/clk/qcom/apss-ipq-pll.c >>> b/drivers/clk/qcom/apss-ipq-pll.c >>> index dd0c01bf5a98..75486a124fcd 100644 >>> --- a/drivers/clk/qcom/apss-ipq-pll.c >>> +++ b/drivers/clk/qcom/apss-ipq-pll.c >>> @@ -33,6 +33,7 @@ static struct clk_alpha_pll ipq_pll = { >>> }, >>> .num_parents = 1, >>> .ops = &clk_alpha_pll_huayra_ops, >>> + .flags = CLK_IS_CRITICAL, >>> }, >>> }, >>> }; >>> diff --git a/drivers/clk/qcom/apss-ipq6018.c >>> b/drivers/clk/qcom/apss-ipq6018.c >>> index f2f502e2d5a4..0d0e7196a4dc 100644 >>> --- a/drivers/clk/qcom/apss-ipq6018.c >>> +++ b/drivers/clk/qcom/apss-ipq6018.c >>> @@ -33,15 +33,21 @@ static const struct parent_map >>> parents_apcs_alias0_clk_src_map[] = { >>> { P_APSS_PLL_EARLY, 5 }, >>> }; >>> +static const struct freq_tbl ftbl_apcs_alias0_clk_src[] = { >>> + { .src = P_APSS_PLL_EARLY, .pre_div = 1 }, >>> + { } >>> +}; >>> + >>> static struct clk_rcg2 apcs_alias0_clk_src = { >>> .cmd_rcgr = 0x0050, >>> + .freq_tbl = ftbl_apcs_alias0_clk_src, >>> .hid_width = 5, >>> .parent_map = parents_apcs_alias0_clk_src_map, >>> .clkr.hw.init = &(struct clk_init_data){ >>> .name = "apcs_alias0_clk_src", >>> .parent_data = parents_apcs_alias0_clk_src, >>> .num_parents = ARRAY_SIZE(parents_apcs_alias0_clk_src), >>> - .ops = &clk_rcg2_mux_closest_ops, >>> + .ops = &clk_rcg2_ops, >>> .flags = CLK_SET_RATE_PARENT, >>> }, >>> }; >> Best Regards, Devi Priya
On 31/01/2023 11:17, Devi Priya wrote: > Thanks for taking time to review the patch > > On 1/13/2023 8:50 PM, Konrad Dybcio wrote: >> >> >> On 13.01.2023 15:36, devi priya wrote: >>> Included CLK_IS_CRITICAL flag which helps to properly enable >>> the APSS PLL during bootup. >> Please describe the issue and not only the user-visible impact it >> makes. Does the PLL get shut down by clk_ignore_unused? Maybe you >> would be interested in the sync_state changes that landed in recent >> -next that may solve it for you? >> >> I don't think it should be always-on, as you have an alternate source >> for low power modes, adding CLK_IS_CRITICAL will keep the PLL enabled >> even if you're not using it. > Yeah, got it. Will drop the critical flag >> >>> clk_rcg2_ops should be used for APSS clock RCG, as other ops >>> will not configure the RCG register >> RCG register meaning RCG register*s*, meaning in this case M/N/D >> which would be required for proper rate setting and not only input >> switching (which arguably doesn't seem to be of much concern on a >> single-parent clock)? This all is not obvious.. >> >> Konrad > The source selection is done by configuring the RCGR config register > with the source entry (P_APSS_PLL_EARLY) added to the frequency table. > Proper rate is achieved by configuring the PLL and hence M/N/D values > are not configured But the clk_rcg2_mux_closest_ops also programs the parent for the clock. So from your description it isn't obvious what is wrong with the current _ops used for the clock. >>> >>> Co-developed-by: Praveenkumar I <quic_ipkumar@quicinc.com> >>> Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com> >>> Signed-off-by: devi priya <quic_devipriy@quicinc.com> >>> --- >>> drivers/clk/qcom/apss-ipq-pll.c | 1 + >>> drivers/clk/qcom/apss-ipq6018.c | 8 +++++++- >>> 2 files changed, 8 insertions(+), 1 deletion(-) >>> >>> diff --git a/drivers/clk/qcom/apss-ipq-pll.c >>> b/drivers/clk/qcom/apss-ipq-pll.c >>> index dd0c01bf5a98..75486a124fcd 100644 >>> --- a/drivers/clk/qcom/apss-ipq-pll.c >>> +++ b/drivers/clk/qcom/apss-ipq-pll.c >>> @@ -33,6 +33,7 @@ static struct clk_alpha_pll ipq_pll = { >>> }, >>> .num_parents = 1, >>> .ops = &clk_alpha_pll_huayra_ops, >>> + .flags = CLK_IS_CRITICAL, >>> }, >>> }, >>> }; >>> diff --git a/drivers/clk/qcom/apss-ipq6018.c >>> b/drivers/clk/qcom/apss-ipq6018.c >>> index f2f502e2d5a4..0d0e7196a4dc 100644 >>> --- a/drivers/clk/qcom/apss-ipq6018.c >>> +++ b/drivers/clk/qcom/apss-ipq6018.c >>> @@ -33,15 +33,21 @@ static const struct parent_map >>> parents_apcs_alias0_clk_src_map[] = { >>> { P_APSS_PLL_EARLY, 5 }, >>> }; >>> +static const struct freq_tbl ftbl_apcs_alias0_clk_src[] = { >>> + { .src = P_APSS_PLL_EARLY, .pre_div = 1 }, >>> + { } >>> +}; >>> + >>> static struct clk_rcg2 apcs_alias0_clk_src = { >>> .cmd_rcgr = 0x0050, >>> + .freq_tbl = ftbl_apcs_alias0_clk_src, >>> .hid_width = 5, >>> .parent_map = parents_apcs_alias0_clk_src_map, >>> .clkr.hw.init = &(struct clk_init_data){ >>> .name = "apcs_alias0_clk_src", >>> .parent_data = parents_apcs_alias0_clk_src, >>> .num_parents = ARRAY_SIZE(parents_apcs_alias0_clk_src), >>> - .ops = &clk_rcg2_mux_closest_ops, >>> + .ops = &clk_rcg2_ops, >>> .flags = CLK_SET_RATE_PARENT, >>> }, >>> }; > Best Regards, > Devi Priya
On 1/31/2023 3:10 PM, Dmitry Baryshkov wrote: > On 31/01/2023 11:17, Devi Priya wrote: >> Thanks for taking time to review the patch >> >> On 1/13/2023 8:50 PM, Konrad Dybcio wrote: >>> >>> >>> On 13.01.2023 15:36, devi priya wrote: >>>> Included CLK_IS_CRITICAL flag which helps to properly enable >>>> the APSS PLL during bootup. >>> Please describe the issue and not only the user-visible impact it >>> makes. Does the PLL get shut down by clk_ignore_unused? Maybe you >>> would be interested in the sync_state changes that landed in recent >>> -next that may solve it for you? >>> >>> I don't think it should be always-on, as you have an alternate source >>> for low power modes, adding CLK_IS_CRITICAL will keep the PLL enabled >>> even if you're not using it. >> Yeah, got it. Will drop the critical flag >>> >>>> clk_rcg2_ops should be used for APSS clock RCG, as other ops >>>> will not configure the RCG register >>> RCG register meaning RCG register*s*, meaning in this case M/N/D >>> which would be required for proper rate setting and not only input >>> switching (which arguably doesn't seem to be of much concern on a >>> single-parent clock)? This all is not obvious.. >>> >>> Konrad >> The source selection is done by configuring the RCGR config register >> with the source entry (P_APSS_PLL_EARLY) added to the frequency table. >> Proper rate is achieved by configuring the PLL and hence M/N/D values >> are not configured > > But the clk_rcg2_mux_closest_ops also programs the parent for the clock. > So from your description it isn't obvious what is wrong with the current > _ops used for the clock. > Okay, understood & agreed. Will re-verify it once and update it accordingly in V2 >>>> >>>> Co-developed-by: Praveenkumar I <quic_ipkumar@quicinc.com> >>>> Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com> >>>> Signed-off-by: devi priya <quic_devipriy@quicinc.com> >>>> --- >>>> drivers/clk/qcom/apss-ipq-pll.c | 1 + >>>> drivers/clk/qcom/apss-ipq6018.c | 8 +++++++- >>>> 2 files changed, 8 insertions(+), 1 deletion(-) >>>> >>>> diff --git a/drivers/clk/qcom/apss-ipq-pll.c >>>> b/drivers/clk/qcom/apss-ipq-pll.c >>>> index dd0c01bf5a98..75486a124fcd 100644 >>>> --- a/drivers/clk/qcom/apss-ipq-pll.c >>>> +++ b/drivers/clk/qcom/apss-ipq-pll.c >>>> @@ -33,6 +33,7 @@ static struct clk_alpha_pll ipq_pll = { >>>> }, >>>> .num_parents = 1, >>>> .ops = &clk_alpha_pll_huayra_ops, >>>> + .flags = CLK_IS_CRITICAL, >>>> }, >>>> }, >>>> }; >>>> diff --git a/drivers/clk/qcom/apss-ipq6018.c >>>> b/drivers/clk/qcom/apss-ipq6018.c >>>> index f2f502e2d5a4..0d0e7196a4dc 100644 >>>> --- a/drivers/clk/qcom/apss-ipq6018.c >>>> +++ b/drivers/clk/qcom/apss-ipq6018.c >>>> @@ -33,15 +33,21 @@ static const struct parent_map >>>> parents_apcs_alias0_clk_src_map[] = { >>>> { P_APSS_PLL_EARLY, 5 }, >>>> }; >>>> +static const struct freq_tbl ftbl_apcs_alias0_clk_src[] = { >>>> + { .src = P_APSS_PLL_EARLY, .pre_div = 1 }, >>>> + { } >>>> +}; >>>> + >>>> static struct clk_rcg2 apcs_alias0_clk_src = { >>>> .cmd_rcgr = 0x0050, >>>> + .freq_tbl = ftbl_apcs_alias0_clk_src, >>>> .hid_width = 5, >>>> .parent_map = parents_apcs_alias0_clk_src_map, >>>> .clkr.hw.init = &(struct clk_init_data){ >>>> .name = "apcs_alias0_clk_src", >>>> .parent_data = parents_apcs_alias0_clk_src, >>>> .num_parents = ARRAY_SIZE(parents_apcs_alias0_clk_src), >>>> - .ops = &clk_rcg2_mux_closest_ops, >>>> + .ops = &clk_rcg2_ops, >>>> .flags = CLK_SET_RATE_PARENT, >>>> }, >>>> }; >> Best Regards, >> Devi Priya > Best Regards, Devi Priya
diff --git a/drivers/clk/qcom/apss-ipq-pll.c b/drivers/clk/qcom/apss-ipq-pll.c index dd0c01bf5a98..75486a124fcd 100644 --- a/drivers/clk/qcom/apss-ipq-pll.c +++ b/drivers/clk/qcom/apss-ipq-pll.c @@ -33,6 +33,7 @@ static struct clk_alpha_pll ipq_pll = { }, .num_parents = 1, .ops = &clk_alpha_pll_huayra_ops, + .flags = CLK_IS_CRITICAL, }, }, }; diff --git a/drivers/clk/qcom/apss-ipq6018.c b/drivers/clk/qcom/apss-ipq6018.c index f2f502e2d5a4..0d0e7196a4dc 100644 --- a/drivers/clk/qcom/apss-ipq6018.c +++ b/drivers/clk/qcom/apss-ipq6018.c @@ -33,15 +33,21 @@ static const struct parent_map parents_apcs_alias0_clk_src_map[] = { { P_APSS_PLL_EARLY, 5 }, }; +static const struct freq_tbl ftbl_apcs_alias0_clk_src[] = { + { .src = P_APSS_PLL_EARLY, .pre_div = 1 }, + { } +}; + static struct clk_rcg2 apcs_alias0_clk_src = { .cmd_rcgr = 0x0050, + .freq_tbl = ftbl_apcs_alias0_clk_src, .hid_width = 5, .parent_map = parents_apcs_alias0_clk_src_map, .clkr.hw.init = &(struct clk_init_data){ .name = "apcs_alias0_clk_src", .parent_data = parents_apcs_alias0_clk_src, .num_parents = ARRAY_SIZE(parents_apcs_alias0_clk_src), - .ops = &clk_rcg2_mux_closest_ops, + .ops = &clk_rcg2_ops, .flags = CLK_SET_RATE_PARENT, }, };