@@ -13000,6 +13000,13 @@ L: netdev@vger.kernel.org
S: Maintained
F: drivers/net/ethernet/mediatek/
+MEDIATEK ETHERNET PCS DRIVER
+M: Daniel Golle <daniel@makrotopia.org>
+L: netdev@vger.kernel.org
+S: Maintained
+F: drivers/net/pcs/pcs-mtk.c
+F: include/linux/pcs/pcs-mtk.h
+
MEDIATEK I2C CONTROLLER DRIVER
M: Qii Wang <qii.wang@mediatek.com>
L: linux-i2c@vger.kernel.org
@@ -18,6 +18,12 @@ config PCS_LYNX
This module provides helpers to phylink for managing the Lynx PCS
which is part of the Layerscape and QorIQ Ethernet SERDES.
+config PCS_MTK
+ tristate
+ help
+ This module provides helpers to phylink for managing the LynxI PCS
+ which is part of MediaTek's SoC and Ethernet switch ICs.
+
config PCS_RZN1_MIIC
tristate "Renesas RZ/N1 MII converter"
depends on OF && (ARCH_RZN1 || COMPILE_TEST)
@@ -5,5 +5,6 @@ pcs_xpcs-$(CONFIG_PCS_XPCS) := pcs-xpcs.o pcs-xpcs-nxp.o
obj-$(CONFIG_PCS_XPCS) += pcs_xpcs.o
obj-$(CONFIG_PCS_LYNX) += pcs-lynx.o
+obj-$(CONFIG_PCS_MTK) += pcs-mtk.o
obj-$(CONFIG_PCS_RZN1_MIIC) += pcs-rzn1-miic.o
obj-$(CONFIG_PCS_ALTERA_TSE) += pcs-altera-tse.o
new file mode 100644
@@ -0,0 +1,314 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018-2019 MediaTek Inc.
+/* A library for MediaTek SGMII circuit
+ *
+ * Author: Sean Wang <sean.wang@mediatek.com>
+ * Author: Daniel Golle <daniel@makrotopia.org>
+ *
+ */
+#include <linux/mdio.h>
+#include <linux/phylink.h>
+#include <linux/pcs/pcs-mtk.h>
+#include <linux/of.h>
+#include <linux/phylink.h>
+#include <linux/regmap.h>
+
+/* SGMII subsystem config registers */
+/* BMCR (low 16) BMSR (high 16) */
+#define SGMSYS_PCS_CONTROL_1 0x0
+#define SGMII_BMCR GENMASK(15, 0)
+#define SGMII_BMSR GENMASK(31, 16)
+#define SGMII_AN_RESTART BIT(9)
+#define SGMII_ISOLATE BIT(10)
+#define SGMII_AN_ENABLE BIT(12)
+#define SGMII_LINK_STATYS BIT(18)
+#define SGMII_AN_ABILITY BIT(19)
+#define SGMII_AN_COMPLETE BIT(21)
+#define SGMII_PCS_FAULT BIT(23)
+#define SGMII_AN_EXPANSION_CLR BIT(30)
+
+#define SGMSYS_PCS_DEVICE_ID 0x4
+#define SGMII_LYNXI_DEV_ID 0x4d544950
+
+#define SGMSYS_PCS_ADVERTISE 0x8
+#define SGMII_ADVERTISE GENMASK(15, 0)
+#define SGMII_LPA GENMASK(31, 16)
+
+#define SGMSYS_PCS_SCRATCH 0x14
+#define SGMII_DEV_VERSION GENMASK(31, 16)
+
+/* Register to programmable link timer, the unit in 2 * 8ns */
+#define SGMSYS_PCS_LINK_TIMER 0x18
+#define SGMII_LINK_TIMER_MASK GENMASK(19, 0)
+#define SGMII_LINK_TIMER_DEFAULT (0x186a0 & SGMII_LINK_TIMER_MASK)
+
+/* Register to control remote fault */
+#define SGMSYS_SGMII_MODE 0x20
+#define SGMII_IF_MODE_SGMII BIT(0)
+#define SGMII_SPEED_DUPLEX_AN BIT(1)
+#define SGMII_SPEED_MASK GENMASK(3, 2)
+#define SGMII_SPEED_10 FIELD_PREP(SGMII_SPEED_MASK, 0)
+#define SGMII_SPEED_100 FIELD_PREP(SGMII_SPEED_MASK, 1)
+#define SGMII_SPEED_1000 FIELD_PREP(SGMII_SPEED_MASK, 2)
+#define SGMII_DUPLEX_HALF BIT(4)
+#define SGMII_REMOTE_FAULT_DIS BIT(8)
+#define SGMII_CODE_SYNC_SET_VAL BIT(9)
+#define SGMII_CODE_SYNC_SET_EN BIT(10)
+#define SGMII_SEND_AN_ERROR_EN BIT(11)
+
+/* Register to reset SGMII design */
+#define SGMII_RESERVED_0 0x34
+#define SGMII_SW_RESET BIT(0)
+
+/* Register to set SGMII speed, ANA RG_ Control Signals III */
+#define SGMSYS_ANA_RG_CS3 0x2028
+#define RG_PHY_SPEED_MASK (BIT(2) | BIT(3))
+#define RG_PHY_SPEED_1_25G 0x0
+#define RG_PHY_SPEED_3_125G BIT(2)
+
+/* Register to power up QPHY */
+#define SGMSYS_QPHY_PWR_STATE_CTRL 0xe8
+#define SGMII_PHYA_PWD BIT(4)
+
+/* Register to QPHY wrapper control */
+#define SGMSYS_QPHY_WRAP_CTRL 0xec
+#define SGMII_PN_SWAP_MASK GENMASK(1, 0)
+#define SGMII_PN_SWAP_TX_RX (BIT(0) | BIT(1))
+
+/* struct mtk_pcs - This structure holds each sgmii regmap and associated
+ * data
+ * @regmap: The register map pointing at the range used to setup
+ * SGMII modes
+ * @dev: Pointer to device owning the PCS
+ * @ana_rgc3: The offset refers to register ANA_RGC3 related to regmap
+ * @interface: Currently configured interface mode
+ * @pcs: Phylink PCS structure
+ * @flags: Flags indicating hardware properties
+ */
+struct mtk_pcs {
+ struct regmap *regmap;
+ struct device *dev;
+ u32 ana_rgc3;
+ phy_interface_t interface;
+ struct phylink_pcs pcs;
+ u32 flags;
+};
+
+static struct mtk_pcs *pcs_to_mtk_pcs(struct phylink_pcs *pcs)
+{
+ return container_of(pcs, struct mtk_pcs, pcs);
+}
+
+static void mtk_pcs_get_state(struct phylink_pcs *pcs,
+ struct phylink_link_state *state)
+{
+ struct mtk_pcs *mpcs = pcs_to_mtk_pcs(pcs);
+ unsigned int bm, adv;
+
+ /* Read the BMSR and LPA */
+ regmap_read(mpcs->regmap, SGMSYS_PCS_CONTROL_1, &bm);
+ regmap_read(mpcs->regmap, SGMSYS_PCS_ADVERTISE, &adv);
+
+ phylink_mii_c22_pcs_decode_state(state, FIELD_GET(SGMII_BMSR, bm),
+ FIELD_GET(SGMII_LPA, adv));
+}
+
+static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
+ phy_interface_t interface,
+ const unsigned long *advertising,
+ bool permit_pause_to_mac)
+{
+ struct mtk_pcs *mpcs = pcs_to_mtk_pcs(pcs);
+ unsigned int rgc3, sgm_mode, bmcr;
+ int advertise, link_timer;
+ bool mode_changed = false, changed, use_an;
+
+ advertise = phylink_mii_c22_pcs_encode_advertisement(interface,
+ advertising);
+ if (advertise < 0)
+ return advertise;
+
+ /* Clearing IF_MODE_BIT0 switches the PCS to BASE-X mode, and
+ * we assume that fixes it's speed at bitrate = line rate (in
+ * other words, 1000Mbps or 2500Mbps).
+ */
+ if (interface == PHY_INTERFACE_MODE_SGMII) {
+ sgm_mode = SGMII_IF_MODE_SGMII;
+ if (phylink_autoneg_inband(mode)) {
+ sgm_mode |= SGMII_REMOTE_FAULT_DIS |
+ SGMII_SPEED_DUPLEX_AN;
+ use_an = true;
+ } else {
+ use_an = false;
+ }
+ } else if (phylink_autoneg_inband(mode)) {
+ /* 1000base-X or 2500base-X autoneg */
+ sgm_mode = SGMII_REMOTE_FAULT_DIS;
+ use_an = linkmode_test_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
+ advertising);
+ } else {
+ /* 1000base-X or 2500base-X without autoneg */
+ sgm_mode = 0;
+ use_an = false;
+ }
+
+ if (use_an)
+ bmcr = SGMII_AN_ENABLE;
+ else
+ bmcr = 0;
+
+ if (mpcs->interface != interface) {
+ /* PHYA power down */
+ regmap_update_bits(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL,
+ SGMII_PHYA_PWD, SGMII_PHYA_PWD);
+
+ /* Reset SGMII PCS state */
+ regmap_update_bits(mpcs->regmap, SGMII_RESERVED_0,
+ SGMII_SW_RESET, SGMII_SW_RESET);
+
+ if (mpcs->flags & MTK_SGMII_FLAG_PN_SWAP)
+ regmap_update_bits(mpcs->regmap, SGMSYS_QPHY_WRAP_CTRL,
+ SGMII_PN_SWAP_MASK,
+ SGMII_PN_SWAP_TX_RX);
+
+ if (interface == PHY_INTERFACE_MODE_2500BASEX)
+ rgc3 = RG_PHY_SPEED_3_125G;
+ else
+ rgc3 = 0;
+
+ /* Configure the underlying interface speed */
+ regmap_update_bits(mpcs->regmap, mpcs->ana_rgc3,
+ RG_PHY_SPEED_MASK, rgc3);
+
+ /* Setup the link timer and QPHY power up inside SGMIISYS */
+ link_timer = phylink_get_link_timer_ns(interface);
+ if (link_timer < 0)
+ return link_timer;
+
+ regmap_write(mpcs->regmap, SGMSYS_PCS_LINK_TIMER, link_timer / 2 / 8);
+
+ mpcs->interface = interface;
+ mode_changed = true;
+ }
+
+ /* Update the advertisement, noting whether it has changed */
+ regmap_update_bits_check(mpcs->regmap, SGMSYS_PCS_ADVERTISE,
+ SGMII_ADVERTISE, advertise, &changed);
+
+ /* Update the sgmsys mode register */
+ regmap_update_bits(mpcs->regmap, SGMSYS_SGMII_MODE,
+ SGMII_REMOTE_FAULT_DIS | SGMII_SPEED_DUPLEX_AN |
+ SGMII_IF_MODE_SGMII, sgm_mode);
+
+ /* Update the BMCR */
+ regmap_update_bits(mpcs->regmap, SGMSYS_PCS_CONTROL_1,
+ SGMII_AN_ENABLE, bmcr);
+
+ /* Release PHYA power down state
+ * Only removing bit SGMII_PHYA_PWD isn't enough.
+ * There are cases when the SGMII_PHYA_PWD register contains 0x9 which
+ * prevents SGMII from working. The SGMII still shows link but no traffic
+ * can flow. Writing 0x0 to the PHYA_PWD register fix the issue. 0x0 was
+ * taken from a good working state of the SGMII interface.
+ * Unknown how much the QPHY needs but it is racy without a sleep.
+ * Tested on mt7622 & mt7986.
+ */
+ usleep_range(50, 100);
+ regmap_write(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL, 0);
+
+ return changed || mode_changed;
+}
+
+static void mtk_pcs_restart_an(struct phylink_pcs *pcs)
+{
+ struct mtk_pcs *mpcs = pcs_to_mtk_pcs(pcs);
+
+ regmap_update_bits(mpcs->regmap, SGMSYS_PCS_CONTROL_1,
+ SGMII_AN_RESTART, SGMII_AN_RESTART);
+}
+
+static void mtk_pcs_link_up(struct phylink_pcs *pcs, unsigned int mode,
+ phy_interface_t interface, int speed, int duplex)
+{
+ struct mtk_pcs *mpcs = pcs_to_mtk_pcs(pcs);
+ unsigned int sgm_mode;
+
+ if (!phylink_autoneg_inband(mode)) {
+ /* Force the speed and duplex setting */
+ if (speed == SPEED_10)
+ sgm_mode = SGMII_SPEED_10;
+ else if (speed == SPEED_100)
+ sgm_mode = SGMII_SPEED_100;
+ else
+ sgm_mode = SGMII_SPEED_1000;
+
+ if (duplex != DUPLEX_FULL)
+ sgm_mode |= SGMII_DUPLEX_HALF;
+
+ regmap_update_bits(mpcs->regmap, SGMSYS_SGMII_MODE,
+ SGMII_DUPLEX_HALF | SGMII_SPEED_MASK,
+ sgm_mode);
+ }
+}
+
+static const struct phylink_pcs_ops mtk_pcs_ops = {
+ .pcs_get_state = mtk_pcs_get_state,
+ .pcs_config = mtk_pcs_config,
+ .pcs_an_restart = mtk_pcs_restart_an,
+ .pcs_link_up = mtk_pcs_link_up,
+};
+
+struct phylink_pcs *mtk_pcs_create(struct device *dev, struct regmap *regmap,
+ u32 ana_rgc3, u32 flags)
+{
+ struct mtk_pcs *mpcs;
+ u32 id, ver;
+ int ret;
+
+ ret = regmap_read(regmap, SGMSYS_PCS_DEVICE_ID, &id);
+ if (ret < 0)
+ return NULL;
+
+ if (id != SGMII_LYNXI_DEV_ID) {
+ dev_err(dev, "unknown PCS device id %08x\n", id);
+ return NULL;
+ }
+
+ ret = regmap_read(regmap, SGMSYS_PCS_SCRATCH, &ver);
+ if (ret < 0)
+ return NULL;
+
+ ver = FIELD_GET(SGMII_DEV_VERSION, ver);
+ if (ver != 0x1) {
+ dev_err(dev, "unknown PCS device version %04x\n", ver);
+ return NULL;
+ }
+
+ dev_dbg(dev, "MediaTek LynxI SGMII PCS (id 0x%08x, ver 0x%04x)\n", id,
+ ver);
+
+ mpcs = kzalloc(sizeof(*mpcs), GFP_KERNEL);
+ if (!mpcs)
+ return NULL;
+
+ mpcs->dev = dev;
+ mpcs->ana_rgc3 = ana_rgc3;
+ mpcs->regmap = regmap;
+ mpcs->flags = flags;
+ mpcs->pcs.ops = &mtk_pcs_ops;
+ mpcs->pcs.poll = true;
+ mpcs->interface = PHY_INTERFACE_MODE_NA;
+
+ return &mpcs->pcs;
+}
+EXPORT_SYMBOL(mtk_pcs_create);
+
+void mtk_pcs_destroy(struct phylink_pcs *pcs)
+{
+ struct mtk_pcs *mpcs = pcs_to_mtk_pcs(pcs);
+
+ kfree(mpcs);
+}
+EXPORT_SYMBOL(mtk_pcs_destroy);
+
+MODULE_LICENSE("GPL");
new file mode 100644
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __LINUX_PCS_MTK_H
+#define __LINUX_PCS_MTK_H
+
+#include <linux/phylink.h>
+#include <linux/regmap.h>
+
+#define MTK_SGMII_FLAG_PN_SWAP BIT(0)
+struct phylink_pcs *mtk_pcs_create(struct device *dev, struct regmap *regmap,
+ u32 ana_rgc3, u32 flags);
+void mtk_pcs_destroy(struct phylink_pcs *pcs);
+
+#endif
The SGMII core found in several MediaTek SoCs is identical to what can also be found in MediaTek's MT7531 Ethernet switch IC. As this has not always been clear, both drivers developed different implementations to deal with the PCS. Add a dedicated driver, mostly by copying the code now found in the Ethernet driver. The now redundant code will be removed by a follow-up commit. Signed-off-by: Daniel Golle <daniel@makrotopia.org> --- MAINTAINERS | 7 + drivers/net/pcs/Kconfig | 6 + drivers/net/pcs/Makefile | 1 + drivers/net/pcs/pcs-mtk.c | 314 ++++++++++++++++++++++++++++++++++++ include/linux/pcs/pcs-mtk.h | 13 ++ 5 files changed, 341 insertions(+) create mode 100644 drivers/net/pcs/pcs-mtk.c create mode 100644 include/linux/pcs/pcs-mtk.h