@@ -17,14 +17,14 @@ config ABP060MG
will be called abp060mg.
config BMP280
- tristate "Bosch Sensortec BMP180/BMP280/BMP380 pressure sensor driver"
+ tristate "Bosch Sensortec BMP180/BMP280/BMP380/BMP580 pressure sensor driver"
depends on (I2C || SPI_MASTER)
select REGMAP
select BMP280_I2C if (I2C)
select BMP280_SPI if (SPI_MASTER)
help
- Say yes here to build support for Bosch Sensortec BMP180, BMP280 and
- BMP380 pressure and temperature sensors. Also supports the BME280 with
+ Say yes here to build support for Bosch Sensortec BMP180, BMP280, BMP380
+ and BMP580 pressure and temperature sensors. Also supports the BME280 with
an additional humidity sensor channel.
To compile this driver as a module, choose M here: the core module
@@ -13,6 +13,7 @@
* https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp280-ds001.pdf
* https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bme280-ds002.pdf
* https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp388-ds001.pdf
+ * https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp581-ds004.pdf
*
* Notice:
* The link to the bmp180 datasheet points to an outdated version missing these changes:
@@ -71,6 +72,41 @@ enum bmp380_odr {
BMP380_ODR_0_0015HZ,
};
+enum bmp580_odr {
+ BMP580_ODR_240HZ,
+ BMP580_ODR_218HZ,
+ BMP580_ODR_199HZ,
+ BMP580_ODR_179HZ,
+ BMP580_ODR_160HZ,
+ BMP580_ODR_149HZ,
+ BMP580_ODR_140HZ,
+ BMP580_ODR_129HZ,
+ BMP580_ODR_120HZ,
+ BMP580_ODR_110HZ,
+ BMP580_ODR_100HZ,
+ BMP580_ODR_89HZ,
+ BMP580_ODR_80HZ,
+ BMP580_ODR_70HZ,
+ BMP580_ODR_60HZ,
+ BMP580_ODR_50HZ,
+ BMP580_ODR_45HZ,
+ BMP580_ODR_40HZ,
+ BMP580_ODR_35HZ,
+ BMP580_ODR_30HZ,
+ BMP580_ODR_25HZ,
+ BMP580_ODR_20HZ,
+ BMP580_ODR_15HZ,
+ BMP580_ODR_10HZ,
+ BMP580_ODR_5HZ,
+ BMP580_ODR_4HZ,
+ BMP580_ODR_3HZ,
+ BMP580_ODR_2HZ,
+ BMP580_ODR_1HZ,
+ BMP580_ODR_0_5HZ,
+ BMP580_ODR_0_25HZ,
+ BMP580_ODR_0_125HZ,
+};
+
/*
* These enums are used for indexing into the array of compensation
* parameters for BMP280.
@@ -1216,6 +1252,303 @@ const struct bmp280_chip_info bmp380_chip_info = {
};
EXPORT_SYMBOL_NS(bmp380_chip_info, IIO_BMP280);
+/*
+ * BMP5xx soft reset procedure
+ */
+static int bmp580_soft_reset(struct bmp280_data *data)
+{
+ unsigned int reg;
+ int ret;
+
+ /* Write reset word to CMD register */
+ ret = regmap_write(data->regmap, BMP580_REG_CMD, BMP580_CMD_SOFT_RESET);
+ if (ret) {
+ dev_err(data->dev, "failed to send reset command to device\n");
+ return ret;
+ }
+ /* Wait 2ms for reset completion */
+ usleep_range(2000, 2500);
+
+ /* Dummy read of chip_id */
+ ret = regmap_read(data->regmap, BMP580_REG_CHIP_ID, ®);
+ if (ret) {
+ dev_err(data->dev, "failed to reestablish comms after reset\n");
+ return ret;
+ }
+
+ /* Check if POR bit is set on interrupt reg */
+ ret = regmap_read(data->regmap, BMP580_REG_INT_STATUS, ®);
+ if (ret) {
+ dev_err(data->dev, "error reading interrupt status register\n");
+ return ret;
+ }
+ if (!(reg & BMP580_INT_STATUS_POR_MASK)) {
+ dev_err(data->dev, "error resetting sensor\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/*
+ * Contrary to previous sensors families, compensation algorithm is builtin.
+ * We are only required to read the register raw data and adapt the ranges
+ * for what is expected on IIO ABI.
+ */
+
+static int bmp580_read_temp(struct bmp280_data *data, int *val)
+{
+ s32 raw_temp;
+ int ret;
+
+ ret = regmap_bulk_read(data->regmap, BMP580_REG_TEMP_XLSB, data->buf,
+ sizeof(data->buf));
+ if (ret) {
+ dev_err(data->dev, "failed to read temperature\n");
+ return ret;
+ }
+
+ raw_temp = get_unaligned_le24(data->buf);
+ if (raw_temp == BMP580_TEMP_SKIPPED) {
+ dev_err(data->dev, "reading temperature skipped\n");
+ return -EIO;
+ }
+
+ /*
+ * Temperature is returned in Celsius degrees in fractional
+ * form down 2^16. We reescale by x1000 to return milli Celsius
+ * to respect IIO ABI.
+ */
+ *val = (raw_temp * 1000) >> 16;
+ return IIO_VAL_INT;
+}
+
+static int bmp580_read_press(struct bmp280_data *data, int *val, int *val2)
+{
+ u32 raw_press;
+ int ret;
+
+ ret = regmap_bulk_read(data->regmap, BMP580_REG_PRESS_XLSB, data->buf,
+ sizeof(data->buf));
+ if (ret) {
+ dev_err(data->dev, "failed to read pressure\n");
+ return ret;
+ }
+
+ raw_press = get_unaligned_le24(data->buf);
+ if (raw_press == BMP580_PRESS_SKIPPED) {
+ dev_err(data->dev, "reading pressure skipped\n");
+ return -EIO;
+ }
+ /*
+ * Pressure is returned in Pascals in fractional form down 2^16.
+ * We reescale /1000 to convert to kilopascal to respect IIO ABI.
+ */
+ *val = raw_press;
+ *val2 = 64000; /* 2^6 * 1000 */
+ return IIO_VAL_FRACTIONAL;
+}
+
+static const int bmp580_odr_table[][2] = {
+ [BMP580_ODR_240HZ] = {240, 0},
+ [BMP580_ODR_218HZ] = {218, 0},
+ [BMP580_ODR_199HZ] = {199, 0},
+ [BMP580_ODR_179HZ] = {179, 0},
+ [BMP580_ODR_160HZ] = {160, 0},
+ [BMP580_ODR_149HZ] = {149, 0},
+ [BMP580_ODR_140HZ] = {140, 0},
+ [BMP580_ODR_129HZ] = {129, 0},
+ [BMP580_ODR_120HZ] = {120, 0},
+ [BMP580_ODR_110HZ] = {110, 0},
+ [BMP580_ODR_100HZ] = {100, 0},
+ [BMP580_ODR_89HZ] = {89, 0},
+ [BMP580_ODR_80HZ] = {80, 0},
+ [BMP580_ODR_70HZ] = {70, 0},
+ [BMP580_ODR_60HZ] = {60, 0},
+ [BMP580_ODR_50HZ] = {50, 0},
+ [BMP580_ODR_45HZ] = {45, 0},
+ [BMP580_ODR_40HZ] = {40, 0},
+ [BMP580_ODR_35HZ] = {35, 0},
+ [BMP580_ODR_30HZ] = {30, 0},
+ [BMP580_ODR_25HZ] = {25, 0},
+ [BMP580_ODR_20HZ] = {20, 0},
+ [BMP580_ODR_15HZ] = {15, 0},
+ [BMP580_ODR_10HZ] = {10, 0},
+ [BMP580_ODR_5HZ] = {5, 0},
+ [BMP580_ODR_4HZ] = {4, 0},
+ [BMP580_ODR_3HZ] = {3, 0},
+ [BMP580_ODR_2HZ] = {2, 0},
+ [BMP580_ODR_1HZ] = {1, 0},
+ [BMP580_ODR_0_5HZ] = {0, 500000},
+ [BMP580_ODR_0_25HZ] = {0, 250000},
+ [BMP580_ODR_0_125HZ] = {0, 125000},
+};
+
+static int bmp580_preinit(struct bmp280_data *data)
+{
+ unsigned int reg;
+ int ret;
+
+ /* Issue soft-reset command */
+ ret = bmp580_soft_reset(data);
+ if (ret)
+ return ret;
+
+ /* Post powerup sequence */
+ ret = regmap_read(data->regmap, BMP580_REG_CHIP_ID, ®);
+ if (ret)
+ return ret;
+
+ /* Print warn message if we don't know the chip id */
+ if (reg != BMP580_CHIP_ID && reg != BMP580_CHIP_ID_ALT)
+ dev_warn(data->dev, "preinit: unexpected chip_id\n");
+
+ ret = regmap_read(data->regmap, BMP580_REG_STATUS, ®);
+ if (ret)
+ return ret;
+
+ /* Check nvm status */
+ if (!(reg & BMP580_STATUS_NVM_RDY_MASK) || (reg & BMP580_STATUS_NVM_ERR_MASK)) {
+ dev_err(data->dev, "preinit: nvm error on powerup sequence\n");
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int bmp580_chip_config(struct bmp280_data *data)
+{
+ bool change = false, aux;
+ unsigned int tmp;
+ u8 reg_val;
+ int ret;
+
+ /* Sets sensor in standby mode */
+ ret = regmap_update_bits(data->regmap, BMP580_REG_ODR_CONFIG,
+ BMP580_MODE_MASK | BMP580_ODR_DEEPSLEEP_DIS,
+ BMP580_ODR_DEEPSLEEP_DIS |
+ FIELD_PREP(BMP580_MODE_MASK, BMP580_MODE_SLEEP));
+ if (ret) {
+ dev_err(data->dev, "failed to change sensor to standby mode\n");
+ return ret;
+ }
+ /* From datasheet's table 4: electrical characteristics */
+ usleep_range(2500, 3000);
+
+ /* Set default DSP mode settings */
+ reg_val = FIELD_PREP(BMP580_DSP_COMP_MASK, BMP580_DSP_PRESS_TEMP_COMP_EN) |
+ BMP580_DSP_SHDW_IIR_TEMP_EN | BMP580_DSP_SHDW_IIR_PRESS_EN;
+
+ ret = regmap_update_bits(data->regmap, BMP580_REG_DSP_CONFIG,
+ BMP580_DSP_COMP_MASK |
+ BMP580_DSP_SHDW_IIR_TEMP_EN |
+ BMP580_DSP_SHDW_IIR_PRESS_EN, reg_val);
+
+ /* Configure oversampling */
+ reg_val = FIELD_PREP(BMP580_OSR_TEMP_MASK, data->oversampling_temp) |
+ FIELD_PREP(BMP580_OSR_PRESS_MASK, data->oversampling_press) |
+ BMP580_OSR_PRESS_EN;
+
+ ret = regmap_update_bits_check(data->regmap, BMP580_REG_OSR_CONFIG,
+ BMP580_OSR_TEMP_MASK | BMP580_OSR_PRESS_MASK |
+ BMP580_OSR_PRESS_EN,
+ reg_val, &aux);
+ if (ret) {
+ dev_err(data->dev, "failed to write oversampling register\n");
+ return ret;
+ }
+ change = change || aux;
+
+ /* Configure output data rate */
+ ret = regmap_update_bits_check(data->regmap, BMP580_REG_ODR_CONFIG, BMP580_ODR_MASK,
+ FIELD_PREP(BMP580_ODR_MASK, data->sampling_freq),
+ &aux);
+ if (ret) {
+ dev_err(data->dev, "failed to write ODR configuration register\n");
+ return ret;
+ }
+ change = change || aux;
+
+ /* Set filter data */
+ reg_val = FIELD_PREP(BMP580_DSP_IIR_PRESS_MASK, data->iir_filter_coeff) |
+ FIELD_PREP(BMP580_DSP_IIR_TEMP_MASK, data->iir_filter_coeff);
+
+ ret = regmap_update_bits_check(data->regmap, BMP580_REG_DSP_IIR,
+ BMP580_DSP_IIR_PRESS_MASK |
+ BMP580_DSP_IIR_TEMP_MASK,
+ reg_val, &aux);
+ if (ret) {
+ dev_err(data->dev, "failed to write config register\n");
+ return ret;
+ }
+ change = change || aux;
+
+ /* Restore sensor to normal operation mode */
+ ret = regmap_write_bits(data->regmap, BMP580_REG_ODR_CONFIG,
+ BMP580_MODE_MASK,
+ FIELD_PREP(BMP580_MODE_MASK, BMP580_MODE_NORMAL));
+ if (ret) {
+ dev_err(data->dev, "failed to set normal mode\n");
+ return ret;
+ }
+ /* From datasheet's table 4: electrical characteristics */
+ usleep_range(3000, 3500);
+
+ if (change) {
+ /*
+ * Check if ODR and OSR settings are valid or we are
+ * operating in a degraded mode.
+ */
+ ret = regmap_read(data->regmap, BMP580_REG_EFF_OSR, &tmp);
+ if (ret) {
+ dev_err(data->dev, "error reading effective OSR register\n");
+ return ret;
+ }
+ if (!(tmp & BMP580_EFF_OSR_VALID_ODR)) {
+ dev_warn(data->dev, "OSR and ODR incompatible settings detected\n");
+ /* Set current OSR settings from data on effective OSR */
+ data->oversampling_temp = FIELD_GET(BMP580_EFF_OSR_TEMP_MASK, tmp);
+ data->oversampling_press = FIELD_GET(BMP580_EFF_OSR_PRESS_MASK, tmp);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+static const int bmp580_oversampling_avail[] = { 1, 2, 4, 8, 16, 32, 64, 128 };
+
+const struct bmp280_chip_info bmp580_chip_info = {
+ .id_reg = BMP580_REG_CHIP_ID,
+ .chip_id = BMP580_CHIP_ID,
+ .regmap_config = &bmp580_regmap_config,
+ .start_up_time = 2000,
+ .channels = bmp380_channels,
+ .num_channels = 2,
+
+ .oversampling_temp_avail = bmp580_oversampling_avail,
+ .num_oversampling_temp_avail = ARRAY_SIZE(bmp580_oversampling_avail),
+ .oversampling_temp_default = ilog2(1),
+
+ .oversampling_press_avail = bmp580_oversampling_avail,
+ .num_oversampling_press_avail = ARRAY_SIZE(bmp580_oversampling_avail),
+ .oversampling_press_default = ilog2(4),
+
+ .sampling_freq_avail = bmp580_odr_table,
+ .num_sampling_freq_avail = ARRAY_SIZE(bmp580_odr_table) * 2,
+ .sampling_freq_default = BMP580_ODR_50HZ,
+
+ .iir_filter_coeffs_avail = bmp380_iir_filter_coeffs_avail,
+ .num_iir_filter_coeffs_avail = ARRAY_SIZE(bmp380_iir_filter_coeffs_avail),
+ .iir_filter_coeff_default = 2,
+
+ .chip_config = bmp580_chip_config,
+ .read_temp = bmp580_read_temp,
+ .read_press = bmp580_read_press,
+ .preinit = bmp580_preinit,
+};
+EXPORT_SYMBOL_NS(bmp580_chip_info, IIO_BMP280);
+
static int bmp180_measure(struct bmp280_data *data, u8 ctrl_meas)
{
const int conversion_time_max[] = { 4500, 7500, 13500, 25500 };
@@ -34,6 +34,7 @@ static const struct of_device_id bmp280_of_i2c_match[] = {
{ .compatible = "bosch,bmp280", .data = &bmp280_chip_info },
{ .compatible = "bosch,bme280", .data = &bme280_chip_info },
{ .compatible = "bosch,bmp380", .data = &bmp380_chip_info },
+ { .compatible = "bosch,bmp580", .data = &bmp580_chip_info },
{ },
};
MODULE_DEVICE_TABLE(of, bmp280_of_i2c_match);
@@ -44,6 +45,7 @@ static const struct i2c_device_id bmp280_i2c_id[] = {
{"bmp280", (kernel_ulong_t)&bmp280_chip_info },
{"bme280", (kernel_ulong_t)&bme280_chip_info },
{"bmp380", (kernel_ulong_t)&bmp380_chip_info },
+ {"bmp580", (kernel_ulong_t)&bmp580_chip_info },
{ },
};
MODULE_DEVICE_TABLE(i2c, bmp280_i2c_id);
@@ -115,6 +115,54 @@ static bool bmp380_is_volatile_reg(struct device *dev, unsigned int reg)
}
}
+static bool bmp580_is_writeable_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case BMP580_REG_NVM_DATA_MSB:
+ case BMP580_REG_NVM_DATA_LSB:
+ case BMP580_REG_NVM_ADDR:
+ case BMP580_REG_ODR_CONFIG:
+ case BMP580_REG_OSR_CONFIG:
+ case BMP580_REG_INT_SOURCE:
+ case BMP580_REG_INT_CONFIG:
+ case BMP580_REG_OOR_THR_MSB:
+ case BMP580_REG_OOR_THR_LSB:
+ case BMP580_REG_OOR_CONFIG:
+ case BMP580_REG_OOR_RANGE:
+ case BMP580_REG_IF_CONFIG:
+ case BMP580_REG_FIFO_CONFIG:
+ case BMP580_REG_FIFO_SEL:
+ case BMP580_REG_DSP_CONFIG:
+ case BMP580_REG_DSP_IIR:
+ case BMP580_REG_CMD:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static bool bmp580_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case BMP580_REG_NVM_DATA_MSB:
+ case BMP580_REG_NVM_DATA_LSB:
+ case BMP580_REG_FIFO_COUNT:
+ case BMP580_REG_INT_STATUS:
+ case BMP580_REG_PRESS_XLSB:
+ case BMP580_REG_PRESS_LSB:
+ case BMP580_REG_PRESS_MSB:
+ case BMP580_REG_FIFO_DATA:
+ case BMP580_REG_TEMP_XLSB:
+ case BMP580_REG_TEMP_LSB:
+ case BMP580_REG_TEMP_MSB:
+ case BMP580_REG_EFF_OSR:
+ case BMP580_REG_STATUS:
+ return true;
+ default:
+ return false;
+ }
+}
+
const struct regmap_config bmp280_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
@@ -138,3 +186,15 @@ const struct regmap_config bmp380_regmap_config = {
.volatile_reg = bmp380_is_volatile_reg,
};
EXPORT_SYMBOL_NS(bmp380_regmap_config, IIO_BMP280);
+
+const struct regmap_config bmp580_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = BMP580_REG_CMD,
+ .cache_type = REGCACHE_RBTREE,
+
+ .writeable_reg = bmp580_is_writeable_reg,
+ .volatile_reg = bmp580_is_volatile_reg,
+};
+EXPORT_SYMBOL_NS(bmp580_regmap_config, IIO_BMP280);
@@ -85,6 +85,7 @@ static const struct of_device_id bmp280_of_spi_match[] = {
{ .compatible = "bosch,bmp280", .data = &bmp280_chip_info },
{ .compatible = "bosch,bme280", .data = &bmp280_chip_info },
{ .compatible = "bosch,bmp380", .data = &bmp380_chip_info },
+ { .compatible = "bosch,bmp580", .data = &bmp580_chip_info },
{ },
};
MODULE_DEVICE_TABLE(of, bmp280_of_spi_match);
@@ -95,6 +96,7 @@ static const struct spi_device_id bmp280_spi_id[] = {
{ "bmp280", (kernel_ulong_t)&bmp280_chip_info },
{ "bme280", (kernel_ulong_t)&bmp280_chip_info },
{ "bmp380", (kernel_ulong_t)&bmp380_chip_info },
+ { "bmp580", (kernel_ulong_t)&bmp580_chip_info },
{ }
};
MODULE_DEVICE_TABLE(spi, bmp280_spi_id);
@@ -6,6 +6,107 @@
#include <linux/regulator/consumer.h>
+/* BMP580 specific registers */
+#define BMP580_REG_CMD 0x7E
+#define BMP580_REG_EFF_OSR 0x38
+#define BMP580_REG_ODR_CONFIG 0x37
+#define BMP580_REG_OSR_CONFIG 0x36
+#define BMP580_REG_IF_CONFIG 0x13
+#define BMP580_REG_REV_ID 0x02
+#define BMP580_REG_CHIP_ID 0x01
+/* OOR allows to configure a pressure alarm */
+#define BMP580_REG_OOR_CONFIG 0x35
+#define BMP580_REG_OOR_RANGE 0x34
+#define BMP580_REG_OOR_THR_MSB 0x33
+#define BMP580_REG_OOR_THR_LSB 0x32
+/* DSP registers (IIR filters) */
+#define BMP580_REG_DSP_IIR 0x31
+#define BMP580_REG_DSP_CONFIG 0x30
+/* NVM access registers */
+#define BMP580_REG_NVM_DATA_MSB 0x2D
+#define BMP580_REG_NVM_DATA_LSB 0x2C
+#define BMP580_REG_NVM_ADDR 0x2B
+/* Status registers */
+#define BMP580_REG_STATUS 0x28
+#define BMP580_REG_INT_STATUS 0x27
+#define BMP580_REG_CHIP_STATUS 0x11
+/* Data registers */
+#define BMP580_REG_FIFO_DATA 0x29
+#define BMP580_REG_PRESS_MSB 0x22
+#define BMP580_REG_PRESS_LSB 0x21
+#define BMP580_REG_PRESS_XLSB 0x20
+#define BMP580_REG_TEMP_MSB 0x1F
+#define BMP580_REG_TEMP_LSB 0x1E
+#define BMP580_REG_TEMP_XLSB 0x1D
+/* FIFO config registers */
+#define BMP580_REG_FIFO_SEL 0x18
+#define BMP580_REG_FIFO_COUNT 0x17
+#define BMP580_REG_FIFO_CONFIG 0x16
+/* Interruptions config registers */
+#define BMP580_REG_INT_SOURCE 0x15
+#define BMP580_REG_INT_CONFIG 0x14
+
+#define BMP580_CMD_NOOP 0x00
+#define BMP580_CMD_EXTMODE_SEQ_0 0x73
+#define BMP580_CMD_EXTMODE_SEQ_1 0xB4
+#define BMP580_CMD_EXTMODE_SEQ_2 0x69
+#define BMP580_CMD_NVM_OP_SEQ_0 0x5D
+#define BMP580_CMD_NVM_READ_SEQ_1 0xA5
+#define BMP580_CMD_NVM_WRITE_SEQ_1 0xA0
+#define BMP580_CMD_SOFT_RESET 0xB6
+
+#define BMP580_INT_STATUS_POR_MASK BIT(4)
+
+#define BMP580_STATUS_CORE_RDY_MASK BIT(0)
+#define BMP580_STATUS_NVM_RDY_MASK BIT(1)
+#define BMP580_STATUS_NVM_ERR_MASK BIT(2)
+#define BMP580_STATUS_NVM_CMD_ERR_MASK BIT(3)
+
+#define BMP580_OSR_PRESS_MASK GENMASK(5, 3)
+#define BMP580_OSR_TEMP_MASK GENMASK(2, 0)
+#define BMP580_OSR_PRESS_EN BIT(6)
+#define BMP580_EFF_OSR_PRESS_MASK GENMASK(5, 3)
+#define BMP580_EFF_OSR_TEMP_MASK GENMASK(2, 0)
+#define BMP580_EFF_OSR_VALID_ODR BIT(7)
+
+#define BMP580_ODR_MASK GENMASK(6, 2)
+#define BMP580_MODE_MASK GENMASK(1, 0)
+#define BMP580_MODE_SLEEP 0
+#define BMP580_MODE_NORMAL 1
+#define BMP580_MODE_FORCED 2
+#define BMP580_MODE_CONTINOUS 3
+#define BMP580_ODR_DEEPSLEEP_DIS BIT(7)
+
+#define BMP580_DSP_COMP_MASK GENMASK(1, 0)
+#define BMP580_DSP_COMP_DIS 0
+#define BMP580_DSP_TEMP_COMP_EN 1
+/*
+ * In section 7.27 of datasheet, modes 2 and 3 are technically the same.
+ * Pressure compensation means also enabling temperature compensation
+ */
+#define BMP580_DSP_PRESS_COMP_EN 2
+#define BMP580_DSP_PRESS_TEMP_COMP_EN 3
+#define BMP580_DSP_IIR_FORCED_FLUSH BIT(2)
+#define BMP580_DSP_SHDW_IIR_TEMP_EN BIT(3)
+#define BMP580_DSP_FIFO_IIR_TEMP_EN BIT(4)
+#define BMP580_DSP_SHDW_IIR_PRESS_EN BIT(5)
+#define BMP580_DSP_FIFO_IIR_PRESS_EN BIT(6)
+#define BMP580_DSP_OOR_IIR_PRESS_EN BIT(7)
+
+#define BMP580_DSP_IIR_PRESS_MASK GENMASK(5, 3)
+#define BMP580_DSP_IIR_TEMP_MASK GENMASK(2, 0)
+#define BMP580_FILTER_OFF 0
+#define BMP580_FILTER_1X 1
+#define BMP580_FILTER_3X 2
+#define BMP580_FILTER_7X 3
+#define BMP580_FILTER_15X 4
+#define BMP580_FILTER_31X 5
+#define BMP580_FILTER_63X 6
+#define BMP580_FILTER_127X 7
+
+#define BMP580_TEMP_SKIPPED 0x7f7f7f
+#define BMP580_PRESS_SKIPPED 0x7f7f7f
+
/* BMP380 specific registers */
#define BMP380_REG_CMD 0x7E
#define BMP380_REG_CONFIG 0x1F
@@ -184,6 +285,8 @@
#define BMP280_REG_ID 0xD0
#define BMP380_CHIP_ID 0x50
+#define BMP580_CHIP_ID 0x50
+#define BMP580_CHIP_ID_ALT 0x51
#define BMP180_CHIP_ID 0x55
#define BMP280_CHIP_ID 0x58
#define BME280_CHIP_ID 0x60
@@ -353,11 +456,13 @@ extern const struct bmp280_chip_info bmp180_chip_info;
extern const struct bmp280_chip_info bmp280_chip_info;
extern const struct bmp280_chip_info bme280_chip_info;
extern const struct bmp280_chip_info bmp380_chip_info;
+extern const struct bmp280_chip_info bmp580_chip_info;
/* Regmap configurations */
extern const struct regmap_config bmp180_regmap_config;
extern const struct regmap_config bmp280_regmap_config;
extern const struct regmap_config bmp380_regmap_config;
+extern const struct regmap_config bmp580_regmap_config;
/* Probe called from different transports */
int bmp280_common_probe(struct device *dev,
Adds compatibility with the new sensor generation, the BMP580. The measurement and initialization codepaths are adapted from the device datasheet and the repository from manufacturer at https://github.com/boschsensortec/BMP5-Sensor-API. Signed-off-by: Angel Iglesias <ang.iglesiasg@gmail.com>