| Message ID | 20230310163420.7582-1-quic_kriskura@quicinc.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | Add multiport support for DWC3 controllers | expand |
Hi Krishna, I'm unable to apply your patch series, it looks like patch 2 is malformed. 'git am' prints the following: Applying: dt-bindings: usb: Add bindings for multiport properties on DWC3 controller Applying: usb: dwc3: core: Access XHCI address space temporarily to read port info error: corrupt patch at line 83 Patch failed at 0002 usb: dwc3: core: Access XHCI address space temporarily to read port info Are you able to apply the series on your side? Best, Adrien
On 3/15/2023 2:02 AM, Adrien Thierry wrote: > Hi Krishna, > > I'm unable to apply your patch series, it looks like patch 2 is malformed. > 'git am' prints the following: > > Applying: dt-bindings: usb: Add bindings for multiport properties on DWC3 controller > Applying: usb: dwc3: core: Access XHCI address space temporarily to read port info > error: corrupt patch at line 83 > Patch failed at 0002 usb: dwc3: core: Access XHCI address space temporarily to read port info > > Are you able to apply the series on your side? > > Best, > > Adrien > Hi Adrien, I rebased them last week before sending them out. Probably code got updated causing conflicts. I will rebase them again this week and send v6 addressing review comments. Regards, Krishna,
Currently the DWC3 driver supports only single port controller which requires at most two PHYs ie HS and SS PHYs. There are SoCs that has DWC3 controller with multiple ports that can operate in host mode. Some of the port supports both SS+HS and other port supports only HS mode. This change primarily refactors the Phy logic in core driver to allow multiport support with Generic Phy's. Chananges have been tested on QCOM SoC SA8295P which has 4 ports (2 are HS+SS capable and 2 are HS only capable). Changes in current version: Added DT support for first port of Teritiary USB controller on SA8540-Ride Added support for reading port info from XHCI Extended Params registers. Changes in RFC v4: Added DT support for SA8295p. Changes in RFC v3: Incase any PHY init fails, then clear/exit the PHYs that are already initialized. Changes in RFC v2: Changed dwc3_count_phys to return the number of PHY Phandles in the node. This will be used now in dwc3_extract_num_phys to increment num_usb2_phy and num_usb3_phy. Added new parameter "ss_idx" in dwc3_core_get_phy_ny_node and changed its structure such that the first half is for HS-PHY and second half is for SS-PHY. In dwc3_core_get_phy, for multiport controller, only if SS-PHY phandle is present, pass proper SS_IDX else pass -1. Link to RFC v4: https://lore.kernel.org/all/20230115114146.12628-1-quic_kriskura@quicinc.com/ Link to RFC v3: https://lore.kernel.org/all/1654709787-23686-1-git-send-email-quic_harshq@quicinc.com/#r Link to RFC v2: https://lore.kernel.org/all/1653560029-6937-1-git-send-email-quic_harshq@quicinc.com/#r Krishna Kurapati (8): dt-bindings: usb: Add bindings for multiport properties on DWC3 controller usb: dwc3: core: Access XHCI address space temporarily to read port info usb: dwc3: core: Skip setting event buffers for host only controllers usb: dwc3: core: Refactor PHY logic to support Multiport Controller usb: dwc3: qcom: Add multiport controller support for qcom wrapper arm64: dts: qcom: sc8280xp: Add multiport controller node for SC8280 arm64: dts: qcom: sa8295p: Enable teritiary controller and its 4 USB ports arm64: dts: qcom: sa8540-ride: Enable first port of teritiary usb controller .../devicetree/bindings/usb/snps,dwc3.yaml | 13 +- arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 47 +++ arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 22 ++ arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 58 +++ drivers/usb/dwc3/core.c | 374 ++++++++++++++---- drivers/usb/dwc3/core.h | 20 +- drivers/usb/dwc3/drd.c | 13 +- drivers/usb/dwc3/dwc3-qcom.c | 28 +- 8 files changed, 473 insertions(+), 102 deletions(-)