| Message ID | 1602307902-16761-3-git-send-email-mdalam@codeaurora.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | mtd: rawnand: qcom: Add support for QSPI nand | expand |
Hello, On Sat, 10 Oct 2020 11:01:39 +0530 Md Sadre Alam <mdalam@codeaurora.org> wrote: > This change will add initial support for qspi (serial nand). > > QPIC Version v.2.0 onwards supports serial nand as well so this > change will initialize all required register to enable qspi (serial > nand). > > This change is supporting very basic functionality of qspi nand flash. > > 1. Reset device (Reset QSPI NAND device). > > 2. Device detection (Read id QSPI NAND device). Unfortunately, that's not going to work in the long term. You're basically hacking the raw NAND framework to make SPI NANDs fit. I do understand the rationale behind this decision (re-using the code for ECC and probably other things), but that's not going to work. So I'd recommend doing the following instead: 1/ implement a SPI-mem controller driver 2/ implement an ECC engine driver so the ECC logic can be shared between the SPI controller and raw NAND controller drivers 3/ convert the raw NAND driver to the exec_op() interface (none of this hack would have been possible if the driver was using the new API) Regards, Boris
On 10/29/2020 2:37 PM, Boris Brezillon wrote: > Hello, > > On Sat, 10 Oct 2020 11:01:39 +0530 > Md Sadre Alam <mdalam@codeaurora.org> wrote: > >> This change will add initial support for qspi (serial nand). >> >> QPIC Version v.2.0 onwards supports serial nand as well so this >> change will initialize all required register to enable qspi (serial >> nand). >> >> This change is supporting very basic functionality of qspi nand flash. >> >> 1. Reset device (Reset QSPI NAND device). >> >> 2. Device detection (Read id QSPI NAND device). > Unfortunately, that's not going to work in the long term. You're > basically hacking the raw NAND framework to make SPI NANDs fit. I do > understand the rationale behind this decision (re-using the code for > ECC and probably other things), but that's not going to work. So I'd > recommend doing the following instead: > > 1/ implement a SPI-mem controller driver > 2/ implement an ECC engine driver so the ECC logic can be shared > between the SPI controller and raw NAND controller drivers > 3/ convert the raw NAND driver to the exec_op() interface (none of > this hack would have been possible if the driver was using the new > API) > > Regards, > > Boris > Sorry for late reply, again started working on this feature support. The QPIC v2 on wards there is serial nand support got added , its not a standard SPI controller its QPIC controller having support for serial nand. All SPI related configuration done by QPIC hardware and its not exposed as SPI bus to the external world. Only based on QPIC_SPI_CFG = 1, serial functionality will get selected. So that no need to implement as SPI-mem controller driver, since its not a SPI controller. Please check the below diagram for top view of QPIC controller. QPIC Wrapper
On 3/6/2023 7:45 PM, Md Sadre Alam wrote: > > On 10/29/2020 2:37 PM, Boris Brezillon wrote: >> Hello, >> >> On Sat, 10 Oct 2020 11:01:39 +0530 >> Md Sadre Alam <mdalam@codeaurora.org> wrote: >> >>> This change will add initial support for qspi (serial nand). >>> >>> QPIC Version v.2.0 onwards supports serial nand as well so this >>> change will initialize all required register to enable qspi (serial >>> nand). >>> >>> This change is supporting very basic functionality of qspi nand flash. >>> >>> 1. Reset device (Reset QSPI NAND device). >>> >>> 2. Device detection (Read id QSPI NAND device). >> Unfortunately, that's not going to work in the long term. You're >> basically hacking the raw NAND framework to make SPI NANDs fit. I do >> understand the rationale behind this decision (re-using the code for >> ECC and probably other things), but that's not going to work. So I'd >> recommend doing the following instead: >> >> 1/ implement a SPI-mem controller driver >> 2/ implement an ECC engine driver so the ECC logic can be shared >> between the SPI controller and raw NAND controller drivers >> 3/ convert the raw NAND driver to the exec_op() interface (none of >> this hack would have been possible if the driver was using the new >> API) >> >> Regards, >> >> Boris >> > Sorry for late reply, again started working on this feature > support. The QPIC v2 on wards there is serial nand support got added > , its not a standard SPI controller > > its QPIC controller having support for serial nand. All SPI related > configuration done by QPIC hardware and its not exposed as SPI bus to > the external world. Only based on > > QPIC_SPI_CFG = 1, serial functionality will get selected. So that > no need to implement as SPI-mem controller driver, since its not a SPI > controller. > > Please check the below diagram for top view of QPIC controller. > >
Hello, quic_mdalam@quicinc.com wrote on Mon, 6 Mar 2023 19:45:58 +0530: > On 10/29/2020 2:37 PM, Boris Brezillon wrote: > > Hello, > > > > On Sat, 10 Oct 2020 11:01:39 +0530 > > Md Sadre Alam <mdalam@codeaurora.org> wrote: > > > >> This change will add initial support for qspi (serial nand). > >> > >> QPIC Version v.2.0 onwards supports serial nand as well so this > >> change will initialize all required register to enable qspi (serial > >> nand). > >> > >> This change is supporting very basic functionality of qspi nand flash. > >> > >> 1. Reset device (Reset QSPI NAND device). > >> > >> 2. Device detection (Read id QSPI NAND device). > > Unfortunately, that's not going to work in the long term. You're > > basically hacking the raw NAND framework to make SPI NANDs fit. I do > > understand the rationale behind this decision (re-using the code for > > ECC and probably other things), but that's not going to work. So I'd > > recommend doing the following instead: > > > > 1/ implement a SPI-mem controller driver > > 2/ implement an ECC engine driver so the ECC logic can be shared > > between the SPI controller and raw NAND controller drivers > > 3/ convert the raw NAND driver to the exec_op() interface (none of > > this hack would have been possible if the driver was using the new > > API) > > > > Regards, > > > > Boris > > > Sorry for late reply, again started working on this feature support. The QPIC v2 on wards there is serial nand support got added , its not a standard SPI controller > > its QPIC controller having support for serial nand. All SPI related configuration done by QPIC hardware and its not exposed as SPI bus to the external world. Only based on > > QPIC_SPI_CFG = 1, serial functionality will get selected. So that no need to implement as SPI-mem controller driver, since its not a SPI controller. > > Please check the below diagram for top view of QPIC controller. One of the hard things in the Linux kernel is to make devices fit frameworks. This feature does not fit the raw NAND framework. It does not follow any of the conventions taken there. It is not gonna be accepted there. You need to expose spi-mem functionalities, even if the spi-proper features are not available. I believe your situation still fits the spi-mem abstraction. Thanks, Miquèl
On 3/6/2023 8:08 PM, Miquel Raynal wrote: > Hello, > > quic_mdalam@quicinc.com wrote on Mon, 6 Mar 2023 19:45:58 +0530: > >> On 10/29/2020 2:37 PM, Boris Brezillon wrote: >>> Hello, >>> >>> On Sat, 10 Oct 2020 11:01:39 +0530 >>> Md Sadre Alam <mdalam@codeaurora.org> wrote: >>> >>>> This change will add initial support for qspi (serial nand). >>>> >>>> QPIC Version v.2.0 onwards supports serial nand as well so this >>>> change will initialize all required register to enable qspi (serial >>>> nand). >>>> >>>> This change is supporting very basic functionality of qspi nand flash. >>>> >>>> 1. Reset device (Reset QSPI NAND device). >>>> >>>> 2. Device detection (Read id QSPI NAND device). >>> Unfortunately, that's not going to work in the long term. You're >>> basically hacking the raw NAND framework to make SPI NANDs fit. I do >>> understand the rationale behind this decision (re-using the code for >>> ECC and probably other things), but that's not going to work. So I'd >>> recommend doing the following instead: >>> >>> 1/ implement a SPI-mem controller driver >>> 2/ implement an ECC engine driver so the ECC logic can be shared >>> between the SPI controller and raw NAND controller drivers >>> 3/ convert the raw NAND driver to the exec_op() interface (none of >>> this hack would have been possible if the driver was using the new >>> API) >>> >>> Regards, >>> >>> Boris >>> >> Sorry for late reply, again started working on this feature support. The QPIC v2 on wards there is serial nand support got added , its not a standard SPI controller >> >> its QPIC controller having support for serial nand. All SPI related configuration done by QPIC hardware and its not exposed as SPI bus to the external world. Only based on >> >> QPIC_SPI_CFG = 1, serial functionality will get selected. So that no need to implement as SPI-mem controller driver, since its not a SPI controller. >> >> Please check the below diagram for top view of QPIC controller. > > One of the hard things in the Linux kernel is to make devices fit > frameworks. This feature does not fit the raw NAND framework. It does > not follow any of the conventions taken there. It is not gonna be > accepted there. You need to expose spi-mem functionalities, even if the > spi-proper features are not available. I believe your situation still > fits the spi-mem abstraction. > > Thanks, > Miquèl I have started writing the driver code for SPI NAND. Please check the below design, is this fine as per Boris suggestion. |------------------------| |------------------------------| |---------------------------------| |qcom spi nand driver |--------------------->|common ECC engine driver |<-----------------------|qcom raw nand driver | | | | | | | | | |drivers/mtd/nand/ecc-qcom.c | |drivers/mtd/nand/raw/qcom_nand.c | | | | | | | |drivers/spi/spi-qpic.c | |------------------------------| | | | | |common API file: | | | | | |common API: reset, read id, | | | | |--------------------->|erase, read page, write page, |<-----------------------| | |------------------------| |bad block check etc. | | | | | |---------------------------------| |drivers/mtd/nand/raw/qpic_comm| | on.c | |------------------------------| Here ECC engine driver as separate file under (drivers/mtd/nand/ecc-qcom.c) and all common APIs like reset, read id, erase, write page, read page, check block bad etc. as separate file under drivers/mtd/nand/raw/qpic_common.c.APIs under ECC engine drivers and qpic_common.c will be exported and used by spi-qpic.c driver (Serial NAND) and qcom_nand.c (raw nand driver). Thanks, Alam.
Hello, + Mark quic_mdalam@quicinc.com wrote on Mon, 27 Mar 2023 19:24:02 +0530: > On 3/6/2023 8:08 PM, Miquel Raynal wrote: > > Hello, > > > > quic_mdalam@quicinc.com wrote on Mon, 6 Mar 2023 19:45:58 +0530: > > > >> On 10/29/2020 2:37 PM, Boris Brezillon wrote: > >>> Hello, > >>> > >>> On Sat, 10 Oct 2020 11:01:39 +0530 > >>> Md Sadre Alam <mdalam@codeaurora.org> wrote: > >>> >>>> This change will add initial support for qspi (serial nand). > >>>> > >>>> QPIC Version v.2.0 onwards supports serial nand as well so this > >>>> change will initialize all required register to enable qspi (serial > >>>> nand). > >>>> > >>>> This change is supporting very basic functionality of qspi nand flash. > >>>> > >>>> 1. Reset device (Reset QSPI NAND device). > >>>> > >>>> 2. Device detection (Read id QSPI NAND device). > >>> Unfortunately, that's not going to work in the long term. You're > >>> basically hacking the raw NAND framework to make SPI NANDs fit. I do > >>> understand the rationale behind this decision (re-using the code for > >>> ECC and probably other things), but that's not going to work. So I'd > >>> recommend doing the following instead: > >>> > >>> 1/ implement a SPI-mem controller driver > >>> 2/ implement an ECC engine driver so the ECC logic can be shared > >>> between the SPI controller and raw NAND controller drivers > >>> 3/ convert the raw NAND driver to the exec_op() interface (none of > >>> this hack would have been possible if the driver was using the new > >>> API) > >>> > >>> Regards, > >>> > >>> Boris > >>> >> Sorry for late reply, again started working on this feature support. The QPIC v2 on wards there is serial nand support got added , its not a standard SPI controller > >> > >> its QPIC controller having support for serial nand. All SPI related configuration done by QPIC hardware and its not exposed as SPI bus to the external world. Only based on > >> > >> QPIC_SPI_CFG = 1, serial functionality will get selected. So that no need to implement as SPI-mem controller driver, since its not a SPI controller. > >> > >> Please check the below diagram for top view of QPIC controller. > > > > One of the hard things in the Linux kernel is to make devices fit > > frameworks. This feature does not fit the raw NAND framework. It does > > not follow any of the conventions taken there. It is not gonna be > > accepted there. You need to expose spi-mem functionalities, even if the > > spi-proper features are not available. I believe your situation still > > fits the spi-mem abstraction. > > > > Thanks, > > Miquèl > > > I have started writing the driver code for SPI NAND. Please check the below design, > is this fine as per Boris suggestion. Thanks. > |------------------------| |------------------------------| |---------------------------------| > |qcom spi nand driver |--------------------->|common ECC engine driver |<-----------------------|qcom raw nand driver | > | | | | | | > | | |drivers/mtd/nand/ecc-qcom.c | |drivers/mtd/nand/raw/qcom_nand.c | > | | | | | | > |drivers/spi/spi-qpic.c | |------------------------------| | | > | | |common API file: | | | > | | |common API: reset, read id, | | | > | |--------------------->|erase, read page, write page, |<-----------------------| | > |------------------------| |bad block check etc. | | | > | | |---------------------------------| > |drivers/mtd/nand/raw/qpic_comm| > | on.c | > |------------------------------| > > > Here ECC engine driver as separate file under (drivers/mtd/nand/ecc-qcom.c) and all > common APIs like reset, read id, erase, write page, read page, check block bad etc. I'm not sure how generic these APIs are, please try to not put anything raw NAND or SPI-NAND specific in the common file. I don't want to see "if (raw)" or "if (spi)" conditions there. > as separate file under drivers/mtd/nand/raw/qpic_common.c.APIs under ECC engine drivers > and qpic_common.c will be exported and used by spi-qpic.c driver (Serial NAND) and qcom_nand.c > (raw nand driver). On my side, I don't have a strong opinion yet but it looks good to me. Can you confirm you are considering switching to the ->exec_op() API in the raw NAND driver? Thanks, Miquèl
On 3/27/2023 8:19 PM, Miquel Raynal wrote: > Hello, > > + Mark > > quic_mdalam@quicinc.com wrote on Mon, 27 Mar 2023 19:24:02 +0530: > >> On 3/6/2023 8:08 PM, Miquel Raynal wrote: >>> Hello, >>> >>> quic_mdalam@quicinc.com wrote on Mon, 6 Mar 2023 19:45:58 +0530: >>> >>>> On 10/29/2020 2:37 PM, Boris Brezillon wrote: >>>>> Hello, >>>>> >>>>> On Sat, 10 Oct 2020 11:01:39 +0530 >>>>> Md Sadre Alam <mdalam@codeaurora.org> wrote: >>>>> >>>> This change will add initial support for qspi (serial nand). >>>>>> >>>>>> QPIC Version v.2.0 onwards supports serial nand as well so this >>>>>> change will initialize all required register to enable qspi (serial >>>>>> nand). >>>>>> >>>>>> This change is supporting very basic functionality of qspi nand flash. >>>>>> >>>>>> 1. Reset device (Reset QSPI NAND device). >>>>>> >>>>>> 2. Device detection (Read id QSPI NAND device). >>>>> Unfortunately, that's not going to work in the long term. You're >>>>> basically hacking the raw NAND framework to make SPI NANDs fit. I do >>>>> understand the rationale behind this decision (re-using the code for >>>>> ECC and probably other things), but that's not going to work. So I'd >>>>> recommend doing the following instead: >>>>> >>>>> 1/ implement a SPI-mem controller driver >>>>> 2/ implement an ECC engine driver so the ECC logic can be shared >>>>> between the SPI controller and raw NAND controller drivers >>>>> 3/ convert the raw NAND driver to the exec_op() interface (none of >>>>> this hack would have been possible if the driver was using the new >>>>> API) >>>>> >>>>> Regards, >>>>> >>>>> Boris >>>>> >> Sorry for late reply, again started working on this feature support. The QPIC v2 on wards there is serial nand support got added , its not a standard SPI controller >>>> >>>> its QPIC controller having support for serial nand. All SPI related configuration done by QPIC hardware and its not exposed as SPI bus to the external world. Only based on >>>> >>>> QPIC_SPI_CFG = 1, serial functionality will get selected. So that no need to implement as SPI-mem controller driver, since its not a SPI controller. >>>> >>>> Please check the below diagram for top view of QPIC controller. >>> >>> One of the hard things in the Linux kernel is to make devices fit >>> frameworks. This feature does not fit the raw NAND framework. It does >>> not follow any of the conventions taken there. It is not gonna be >>> accepted there. You need to expose spi-mem functionalities, even if the >>> spi-proper features are not available. I believe your situation still >>> fits the spi-mem abstraction. >>> >>> Thanks, >>> Miquèl >> >> >> I have started writing the driver code for SPI NAND. Please check the below design, >> is this fine as per Boris suggestion. > > Thanks. > > >> |------------------------| |------------------------------| |---------------------------------| >> |qcom spi nand driver |--------------------->|common ECC engine driver |<-----------------------|qcom raw nand driver | >> | | | | | | >> | | |drivers/mtd/nand/ecc-qcom.c | |drivers/mtd/nand/raw/qcom_nand.c | >> | | | | | | >> |drivers/spi/spi-qpic.c | |------------------------------| | | >> | | |common API file: | | | >> | | |common API: reset, read id, | | | >> | |--------------------->|erase, read page, write page, |<-----------------------| | >> |------------------------| |bad block check etc. | | | >> | | |---------------------------------| >> |drivers/mtd/nand/raw/qpic_comm| >> | on.c | >> |------------------------------| >> >> >> Here ECC engine driver as separate file under (drivers/mtd/nand/ecc-qcom.c) and all >> common APIs like reset, read id, erase, write page, read page, check block bad etc. > > I'm not sure how generic these APIs are, please try to not put anything > raw NAND or SPI-NAND specific in the common file. I don't want to see > "if (raw)" or "if (spi)" conditions there. I agree , I will not try to put any condition like if(raw) or if(spi). I am doing in the below sequence. 1) exec->op() in raw nand driver 2) Move ecc related code to new ecc engine driver under ./drivers/mtd/nand/ecc-qcom.c and make raw nand driver to work with this ecc engine driver. 3) Write separate SPI-mem driver under ./drivers/spi/spi-qpic.c 4) Move common code under qpic_common.c under ./driver/mtd/nand/raw/qpic_common.c > >> as separate file under drivers/mtd/nand/raw/qpic_common.c.APIs under ECC engine drivers >> and qpic_common.c will be exported and used by spi-qpic.c driver (Serial NAND) and qcom_nand.c >> (raw nand driver). > > On my side, I don't have a strong opinion yet but it looks good to me. > > Can you confirm you are considering switching to the ->exec_op() API in > the raw NAND driver? Yes, first priority is switching to ->exec_op() API in raw nand driver. I have already started and sent couple of patches, will address latest comment send again. > > Thanks, > Miquèl
diff --git a/drivers/mtd/nand/raw/nand_ids.c b/drivers/mtd/nand/raw/nand_ids.c index b994579..32bc419 100644 --- a/drivers/mtd/nand/raw/nand_ids.c +++ b/drivers/mtd/nand/raw/nand_ids.c @@ -55,6 +55,19 @@ struct nand_flash_dev nand_flash_ids[] = { { .id = {0x98, 0xdc, 0x91, 0x15, 0x76} }, SZ_2K, SZ_512, SZ_128K, 0, 5, 128, NAND_ECC_INFO(8, SZ_512) }, + {"GD5F1GQ4RE9IG SPI NAND 1G 1.8V 4-bit", + { .id = {0xc8, 0xc1} }, + SZ_2K, SZ_128, SZ_128K, 0, 2, 128, NAND_ECC_INFO(8, SZ_512) }, + {"GD5F1GQ4RE9IH SPI NAND 1G 1.8V 4-bit", + { .id = {0xc8, 0xc9} }, + SZ_2K, SZ_128, SZ_128K, 0, 2, 64, NAND_ECC_INFO(4, SZ_512) }, + {"GD5F2GQ5REYIH SPI NAND 2G 4-bit", + { .id = {0xc8, 0x22} }, + SZ_2K, SZ_256, SZ_128K, 0, 2, 64, NAND_ECC_INFO(4, SZ_512) }, + {"MT29F1G01ABBFDWB-IT SPI NAND 1G 1.8V 4-bit", + { .id = {0x2c, 0x15} }, + SZ_2K, SZ_128, SZ_128K, 0, 2, 128, NAND_ECC_INFO(8, SZ_512) }, + LEGACY_ID_NAND("NAND 4MiB 5V 8-bit", 0x6B, 4, SZ_8K, SP_OPTIONS), LEGACY_ID_NAND("NAND 4MiB 3,3V 8-bit", 0xE3, 4, SZ_8K, SP_OPTIONS), LEGACY_ID_NAND("NAND 4MiB 3,3V 8-bit", 0xE5, 4, SZ_8K, SP_OPTIONS), diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c index bd7a725..f5064ab 100644 --- a/drivers/mtd/nand/raw/qcom_nandc.c +++ b/drivers/mtd/nand/raw/qcom_nandc.c @@ -36,18 +36,33 @@ #define NAND_DEV_CMD1 0xa4 #define NAND_DEV_CMD2 0xa8 #define NAND_DEV_CMD_VLD 0xac +#define NAND_DEV_CMD7 0xb0 +#define NAND_DEV_CMD8 0xb4 +#define NAND_DEV_CMD9 0xb8 +#define NAND_FLASH_SPI_CFG 0xc0 +#define NAND_SPI_NUM_ADDR_CYCLES 0xc4 +#define NAND_SPI_BUSY_CHECK_WAIT_CNT 0xc8 +#define NAND_DEV_CMD3 0xd0 +#define NAND_DEV_CMD4 0xd4 +#define NAND_DEV_CMD5 0xd8 +#define NAND_DEV_CMD6 0xdc #define SFLASHC_BURST_CFG 0xe0 #define NAND_ERASED_CW_DETECT_CFG 0xe8 #define NAND_ERASED_CW_DETECT_STATUS 0xec #define NAND_EBI2_ECC_BUF_CFG 0xf0 #define FLASH_BUF_ACC 0x100 - #define NAND_CTRL 0xf00 #define NAND_VERSION 0xf08 #define NAND_READ_LOCATION_0 0xf20 #define NAND_READ_LOCATION_1 0xf24 #define NAND_READ_LOCATION_2 0xf28 #define NAND_READ_LOCATION_3 0xf2c +#define NAND_READ_LOCATION_LAST_CW_0 0xf40 +#define NAND_READ_LOCATION_LAST_CW_1 0xf44 +#define NAND_READ_LOCATION_LAST_CW_2 0xf48 +#define NAND_READ_LOCATION_LAST_CW_3 0xf4c +#define NAND_QSPI_MSTR_CONFIG 0xf60 + /* dummy register offsets, used by write_reg_dma */ #define NAND_DEV_CMD1_RESTORE 0xdead @@ -180,6 +195,28 @@ #define ECC_BCH_4BIT BIT(2) #define ECC_BCH_8BIT BIT(3) +/* QSPI NAND config reg bits */ +#define LOAD_CLK_CNTR_INIT_EN (1 << 28) +#define CLK_CNTR_INIT_VAL_VEC 0x924 +#define FEA_STATUS_DEV_ADDR 0xc0 +#define SPI_CFG (1 << 0) + +/* CMD register value for qspi nand */ +#define CMD0_VAL 0x1080D8D8 +#define CMD1_VAL 0xF00F3000 +#define CMD2_VAL 0xF0FF709F +#define CMD3_VAL 0x3F310015 +#define CMD7_VAL 0x04061F0F +#define CMD_VLD_VAL 0xd +#define SPI_NUM_ADDR 0xDA4DB +#define WAIT_CNT 0x10 + +/* QSPI NAND CMD reg bits value */ +#define SPI_WP (1 << 28) +#define SPI_HOLD (1 << 27) +#define SPI_TRANSFER_MODE_x1 (1 << 29) +#define SPI_TRANSFER_MODE_x4 (3 << 29) + #define nandc_set_read_loc(nandc, reg, offset, size, is_last) \ nandc_set_reg(nandc, NAND_READ_LOCATION_##reg, \ ((offset) << READ_LOCATION_OFFSET) | \ @@ -315,6 +352,9 @@ struct nandc_regs { __le32 read_location1; __le32 read_location2; __le32 read_location3; + __le32 spi_cfg; + __le32 num_addr_cycle; + __le32 busy_wait_cnt; __le32 erased_cw_detect_cfg_clr; __le32 erased_cw_detect_cfg_set; @@ -368,6 +408,7 @@ struct qcom_nand_controller { struct clk *core_clk; struct clk *aon_clk; + struct clk *iomacro_clk; union { /* will be used only by QPIC for BAM DMA */ @@ -461,12 +502,14 @@ struct qcom_nand_host { * @is_bam - whether NAND controller is using BAM * @is_qpic - whether NAND CTRL is part of qpic IP * @dev_cmd_reg_start - NAND_DEV_CMD_* registers starting offset + * @is_serial_nand - QSPI nand flag, whether QPIC support serial nand or not */ struct qcom_nandc_props { u32 ecc_modes; bool is_bam; bool is_qpic; u32 dev_cmd_reg_start; + bool is_serial_nand; }; /* Frees the BAM transaction memory */ @@ -641,6 +684,12 @@ static __le32 *offset_to_nandc_reg(struct nandc_regs *regs, int offset) return ®s->read_location2; case NAND_READ_LOCATION_3: return ®s->read_location3; + case NAND_FLASH_SPI_CFG: + return ®s->spi_cfg; + case NAND_SPI_NUM_ADDR_CYCLES: + return ®s->num_addr_cycle; + case NAND_SPI_BUSY_CHECK_WAIT_CNT: + return ®s->busy_wait_cnt; default: return NULL; } @@ -1245,11 +1294,23 @@ static int read_id(struct qcom_nand_host *host, int column) { struct nand_chip *chip = &host->chip; struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + u32 cmd = OP_FETCH_ID; if (column == -1) return 0; - nandc_set_reg(nandc, NAND_FLASH_CMD, OP_FETCH_ID); + if (nandc->props->is_serial_nand) { + cmd |= (SPI_WP | SPI_HOLD | SPI_TRANSFER_MODE_x1); + /* For spi nand read 2-bytes id only + * else if nandc->buf_count == 4; then the id value + * will repeat and the SLC device will be detect as MLC. + * by nand base layer + * so overwrite the nandc->buf_count == 2; + */ + nandc->buf_count = 2; + } + + nandc_set_reg(nandc, NAND_FLASH_CMD, cmd); nandc_set_reg(nandc, NAND_ADDR0, column); nandc_set_reg(nandc, NAND_ADDR1, 0); nandc_set_reg(nandc, NAND_FLASH_CHIP_SELECT, @@ -1269,8 +1330,13 @@ static int reset(struct qcom_nand_host *host) { struct nand_chip *chip = &host->chip; struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); + int cmd_rst; + + cmd_rst = OP_RESET_DEVICE; + if (nandc->props->is_serial_nand) + cmd_rst |= (SPI_WP | SPI_HOLD | SPI_TRANSFER_MODE_x1); - nandc_set_reg(nandc, NAND_FLASH_CMD, OP_RESET_DEVICE); + nandc_set_reg(nandc, NAND_FLASH_CMD, cmd_rst); nandc_set_reg(nandc, NAND_EXEC_CMD, 1); write_reg_dma(nandc, NAND_FLASH_CMD, 1, NAND_BAM_NEXT_SGL); @@ -2470,6 +2536,8 @@ static int qcom_nand_attach_chip(struct nand_chip *chip) int cwperpage, bad_block_byte, ret; bool wide_bus; int ecc_mode = 1; + int num_addr_cycle = 5, dsbl_sts_aftr_write = 0; + int wr_rd_bsy_gap = 2, recovery_cycle = 7; /* controller only supports 512 bytes data steps */ ecc->size = NANDC_STEP_SIZE; @@ -2571,33 +2639,43 @@ static int qcom_nand_attach_chip(struct nand_chip *chip) host->cw_size = host->cw_data + ecc->bytes; bad_block_byte = mtd->writesize - host->cw_size * (cwperpage - 1) + 1; + /* For QSPI serial nand QPIC config register value got changed + * so configure the new value for qspi serial nand + */ + if (nandc->props->is_serial_nand) { + num_addr_cycle = 3; + dsbl_sts_aftr_write = 1; + wr_rd_bsy_gap = 20; + recovery_cycle = 0; + } + host->cfg0 = (cwperpage - 1) << CW_PER_PAGE | host->cw_data << UD_SIZE_BYTES - | 0 << DISABLE_STATUS_AFTER_WRITE - | 5 << NUM_ADDR_CYCLES + | dsbl_sts_aftr_write << DISABLE_STATUS_AFTER_WRITE + | num_addr_cycle << NUM_ADDR_CYCLES | host->ecc_bytes_hw << ECC_PARITY_SIZE_BYTES_RS | 0 << STATUS_BFR_READ | 1 << SET_RD_MODE_AFTER_STATUS | host->spare_bytes << SPARE_SIZE_BYTES; - host->cfg1 = 7 << NAND_RECOVERY_CYCLES + host->cfg1 = recovery_cycle << NAND_RECOVERY_CYCLES | 0 << CS_ACTIVE_BSY | bad_block_byte << BAD_BLOCK_BYTE_NUM | 0 << BAD_BLOCK_IN_SPARE_AREA - | 2 << WR_RD_BSY_GAP + | wr_rd_bsy_gap << WR_RD_BSY_GAP | wide_bus << WIDE_FLASH | host->bch_enabled << ENABLE_BCH_ECC; host->cfg0_raw = (cwperpage - 1) << CW_PER_PAGE | host->cw_size << UD_SIZE_BYTES - | 5 << NUM_ADDR_CYCLES + | num_addr_cycle << NUM_ADDR_CYCLES | 0 << SPARE_SIZE_BYTES; - host->cfg1_raw = 7 << NAND_RECOVERY_CYCLES + host->cfg1_raw = recovery_cycle << NAND_RECOVERY_CYCLES | 0 << CS_ACTIVE_BSY | 17 << BAD_BLOCK_BYTE_NUM | 1 << BAD_BLOCK_IN_SPARE_AREA - | 2 << WR_RD_BSY_GAP + | wr_rd_bsy_gap << WR_RD_BSY_GAP | wide_bus << WIDE_FLASH | 1 << DEV0_CFG1_ECC_DISABLE; @@ -2805,6 +2883,47 @@ static int qcom_nandc_setup(struct qcom_nand_controller *nandc) return 0; } +static void qspi_write_reg_bam(struct qcom_nand_controller *nandc, + unsigned int val, unsigned int reg) +{ + int ret; + + clear_bam_transaction(nandc); + nandc_set_reg(nandc, reg, val); + write_reg_dma(nandc, reg, 1, NAND_BAM_NEXT_SGL); + + ret = submit_descs(nandc); + if (ret) + dev_err(nandc->dev, "Error in submitting descriptor to write config reg\n"); + free_descs(nandc); +} + +static void qspi_nand_init(struct qcom_nand_controller *nandc) +{ + u32 spi_cfg_val = 0x0; + u32 reg = 0x0; + + spi_cfg_val |= (LOAD_CLK_CNTR_INIT_EN | CLK_CNTR_INIT_VAL_VEC + | FEA_STATUS_DEV_ADDR | SPI_CFG); + + qspi_write_reg_bam(nandc, 0x0, NAND_FLASH_SPI_CFG); + qspi_write_reg_bam(nandc, spi_cfg_val, NAND_FLASH_SPI_CFG); + spi_cfg_val &= ~LOAD_CLK_CNTR_INIT_EN; + qspi_write_reg_bam(nandc, spi_cfg_val, NAND_FLASH_SPI_CFG); + + reg = dev_cmd_reg_addr(nandc, NAND_DEV_CMD0); + nandc_write(nandc, reg, CMD0_VAL); + nandc_write(nandc, reg + 4, CMD1_VAL); + nandc_write(nandc, reg + 8, CMD2_VAL); + nandc_write(nandc, reg + 12, CMD_VLD_VAL); + nandc_write(nandc, reg + 16, CMD7_VAL); + reg = dev_cmd_reg_addr(nandc, NAND_DEV_CMD3); + nandc_write(nandc, reg, CMD3_VAL); + + qspi_write_reg_bam(nandc, SPI_NUM_ADDR, NAND_SPI_NUM_ADDR_CYCLES); + qspi_write_reg_bam(nandc, WAIT_CNT, NAND_SPI_BUSY_CHECK_WAIT_CNT); +} + static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc, struct qcom_nand_host *host, struct device_node *dn) @@ -2854,6 +2973,9 @@ static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc, /* set up initial status value */ host->status = NAND_STATUS_READY | NAND_STATUS_WP; + if (nandc->props->is_serial_nand) + qspi_nand_init(nandc); + ret = nand_scan(chip, 1); if (ret) return ret; @@ -2961,6 +3083,12 @@ static int qcom_nandc_probe(struct platform_device *pdev) if (IS_ERR(nandc->aon_clk)) return PTR_ERR(nandc->aon_clk); + if (nandc->props->is_serial_nand) { + nandc->iomacro_clk = devm_clk_get(dev, "io_macro"); + if (IS_ERR(nandc->iomacro_clk)) + return PTR_ERR(nandc->iomacro_clk); + } + ret = qcom_nandc_parse_dt(pdev); if (ret) return ret; @@ -2989,6 +3117,12 @@ static int qcom_nandc_probe(struct platform_device *pdev) if (ret) goto err_aon_clk; + if (nandc->props->is_serial_nand) { + ret = clk_prepare_enable(nandc->iomacro_clk); + if (ret) + goto err_setup; + } + ret = qcom_nandc_setup(nandc); if (ret) goto err_setup; @@ -3042,6 +3176,7 @@ static const struct qcom_nandc_props ipq806x_nandc_props = { .ecc_modes = (ECC_RS_4BIT | ECC_BCH_8BIT), .is_bam = false, .dev_cmd_reg_start = 0x0, + .is_serial_nand = false, }; static const struct qcom_nandc_props ipq4019_nandc_props = { @@ -3049,6 +3184,7 @@ static const struct qcom_nandc_props ipq4019_nandc_props = { .is_bam = true, .is_qpic = true, .dev_cmd_reg_start = 0x0, + .is_serial_nand = false, }; static const struct qcom_nandc_props ipq8074_nandc_props = { @@ -3056,6 +3192,14 @@ static const struct qcom_nandc_props ipq8074_nandc_props = { .is_bam = true, .is_qpic = true, .dev_cmd_reg_start = 0x7000, + .is_serial_nand = false, +}; + +static const struct qcom_nandc_props ipq5018_nandc_props = { + .ecc_modes = (ECC_BCH_4BIT | ECC_BCH_8BIT), + .is_bam = true, + .dev_cmd_reg_start = 0x7000, + .is_serial_nand = true, }; /* @@ -3075,6 +3219,10 @@ static const struct of_device_id qcom_nandc_of_match[] = { .compatible = "qcom,ipq8074-nand", .data = &ipq8074_nandc_props, }, + { + .compatible = "qcom,ipq5018-nand", + .data = &ipq5018_nandc_props, + }, {} }; MODULE_DEVICE_TABLE(of, qcom_nandc_of_match);
This change will add initial support for qspi (serial nand). QPIC Version v.2.0 onwards supports serial nand as well so this change will initialize all required register to enable qspi (serial nand). This change is supporting very basic functionality of qspi nand flash. 1. Reset device (Reset QSPI NAND device). 2. Device detection (Read id QSPI NAND device). Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org> --- drivers/mtd/nand/raw/nand_ids.c | 13 +++ drivers/mtd/nand/raw/qcom_nandc.c | 168 +++++++++++++++++++++++++++++++++++--- 2 files changed, 171 insertions(+), 10 deletions(-)