diff mbox series

[v4,5/5] docs: perf: Minimal introduction the the CXL PMU device and driver

Message ID 20230330164556.31533-6-Jonathan.Cameron@huawei.com
State New, archived
Headers show
Series CXL 3.0 Performance Monitoring Unit support | expand

Commit Message

Jonathan Cameron March 30, 2023, 4:45 p.m. UTC
Very basic introduction to the device and the current driver support
provided. I expect to expand on this in future versions of this patch
set.

Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

--
v4: No change
---
 Documentation/admin-guide/perf/cxl.rst   | 65 ++++++++++++++++++++++++
 Documentation/admin-guide/perf/index.rst |  1 +
 2 files changed, 66 insertions(+)

Comments

Liang, Kan April 3, 2023, 5:45 p.m. UTC | #1
On 2023-03-30 12:45 p.m., Jonathan Cameron wrote:
> Very basic introduction to the device and the current driver support
> provided. I expect to expand on this in future versions of this patch
> set.
> 
> Reviewed-by: Dave Jiang <dave.jiang@intel.com>
> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> 
> --
> v4: No change
> ---
>  Documentation/admin-guide/perf/cxl.rst   | 65 ++++++++++++++++++++++++
>  Documentation/admin-guide/perf/index.rst |  1 +
>  2 files changed, 66 insertions(+)
> 
> diff --git a/Documentation/admin-guide/perf/cxl.rst b/Documentation/admin-guide/perf/cxl.rst
> new file mode 100644
> index 000000000000..46235dff4b21
> --- /dev/null
> +++ b/Documentation/admin-guide/perf/cxl.rst
> @@ -0,0 +1,65 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +======================================
> +CXL Performance Monitoring Unit (CPMU)
> +======================================
> +
> +The CXL rev 3.0 specification provides a definition of CXL Performance
> +Monitoring Unit in section 13.2: Performance Monitoring.
> +
> +CXL components (e.g. Root Port, Switch Upstream Port, End Point) may have
> +any number of CPMU instances. CPMU capabilities are fully discoverable from
> +the devices. The specification provides event definitions for all CXL protocol
> +message types and a set of additional events for things commonly counted on
> +CXL devices (e.g. DRAM events).
> +
> +CPMU driver
> +===========
> +
> +The CPMU driver register a perf PMU with the name cpmu<id> on the CXL bus.
> +
> +    /sys/bus/cxl/device/cpmu<id>
> +
> +The associated PMU is registered as
> +
> +   /sys/bus/event_sources/devices/cpmu<id>
> +
> +In common with other CXL bus devices, the id has no specific meaning and the
> +relationship to specific CXL device should be established via the device parent
> +of the device on the CXL bus.
> +
> +PMU driver provides description of available events and filter options in sysfs.
> +
> +The "format" directory describes all formats of the config (event vendor id,
> +group id and mask) config1 (threshold, filter enables) and config2 (filter
> +parameters) fields of the perf_event_attr structure.  The "events" directory
> +describes all documented events show in perf list.
> +
> +The events shown in perf list are the most fine grained events with a single
> +bit of the event mask set. More general events may be enable by setting
> +multiple mask bits in config. For example, all Device to Host Read Requests
> +may be captured on a single counter by setting the bits for all of
> +
> +* d2h_req_rdcurr
> +* d2h_req_rdown
> +* d2h_req_rdshared
> +* d2h_req_rdany
> +* d2h_req_rdownnodata
> +
> +Example of usage::
> +
> +  $#perf list
> +  cpmu0/clock_ticks/                                 [Kernel PMU event]
> +  cpmu0/d2h_req_itomwr/                              [Kernel PMU event]
> +  cpmu0/d2h_req_rdany/                               [Kernel PMU event]
> +  cpmu0/d2h_req_rdcurr/                              [Kernel PMU event]
> +  -----------------------------------------------------------
> +
> +  $# perf stat -e cpmu0/clock_ticks/ -e cpmu0/d2h_req_itowrm/
> +
> +Vendor specific events may also be available and if so can be used via
> +
> +  $# perf stat -e cpmu0/vid=VID,gid=GID,mask=MASK/
> +
> +The driver does not support sampling. So "perf record" and attaching to
> +a task are unsupported.

The PMU only supports system-wide counting. That's the reason it doesn't
support per-task profiling. Not because of missing sampling.

Thanks,
Kan
> diff --git a/Documentation/admin-guide/perf/index.rst b/Documentation/admin-guide/perf/index.rst
> index 9de64a40adab..f60be04e4e33 100644
> --- a/Documentation/admin-guide/perf/index.rst
> +++ b/Documentation/admin-guide/perf/index.rst
> @@ -21,3 +21,4 @@ Performance monitor support
>     alibaba_pmu
>     nvidia-pmu
>     meson-ddr-pmu
> +   cxl
Jonathan Cameron April 4, 2023, 4:55 p.m. UTC | #2
On Mon, 3 Apr 2023 13:45:52 -0400
"Liang, Kan" <kan.liang@linux.intel.com> wrote:

> On 2023-03-30 12:45 p.m., Jonathan Cameron wrote:
> > Very basic introduction to the device and the current driver support
> > provided. I expect to expand on this in future versions of this patch
> > set.
> > 
> > Reviewed-by: Dave Jiang <dave.jiang@intel.com>
> > Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> > 
> > --
> > v4: No change
> > ---
> >  Documentation/admin-guide/perf/cxl.rst   | 65 ++++++++++++++++++++++++
> >  Documentation/admin-guide/perf/index.rst |  1 +
> >  2 files changed, 66 insertions(+)
> > 
> > diff --git a/Documentation/admin-guide/perf/cxl.rst b/Documentation/admin-guide/perf/cxl.rst
> > new file mode 100644
> > index 000000000000..46235dff4b21
> > --- /dev/null
> > +++ b/Documentation/admin-guide/perf/cxl.rst
> > @@ -0,0 +1,65 @@
> > +.. SPDX-License-Identifier: GPL-2.0
> > +
> > +======================================
> > +CXL Performance Monitoring Unit (CPMU)
> > +======================================
> > +
> > +The CXL rev 3.0 specification provides a definition of CXL Performance
> > +Monitoring Unit in section 13.2: Performance Monitoring.
> > +
> > +CXL components (e.g. Root Port, Switch Upstream Port, End Point) may have
> > +any number of CPMU instances. CPMU capabilities are fully discoverable from
> > +the devices. The specification provides event definitions for all CXL protocol
> > +message types and a set of additional events for things commonly counted on
> > +CXL devices (e.g. DRAM events).
> > +
> > +CPMU driver
> > +===========
> > +
> > +The CPMU driver register a perf PMU with the name cpmu<id> on the CXL bus.
> > +
> > +    /sys/bus/cxl/device/cpmu<id>
> > +
> > +The associated PMU is registered as
> > +
> > +   /sys/bus/event_sources/devices/cpmu<id>
> > +
> > +In common with other CXL bus devices, the id has no specific meaning and the
> > +relationship to specific CXL device should be established via the device parent
> > +of the device on the CXL bus.
> > +
> > +PMU driver provides description of available events and filter options in sysfs.
> > +
> > +The "format" directory describes all formats of the config (event vendor id,
> > +group id and mask) config1 (threshold, filter enables) and config2 (filter
> > +parameters) fields of the perf_event_attr structure.  The "events" directory
> > +describes all documented events show in perf list.
> > +
> > +The events shown in perf list are the most fine grained events with a single
> > +bit of the event mask set. More general events may be enable by setting
> > +multiple mask bits in config. For example, all Device to Host Read Requests
> > +may be captured on a single counter by setting the bits for all of
> > +
> > +* d2h_req_rdcurr
> > +* d2h_req_rdown
> > +* d2h_req_rdshared
> > +* d2h_req_rdany
> > +* d2h_req_rdownnodata
> > +
> > +Example of usage::
> > +
> > +  $#perf list
> > +  cpmu0/clock_ticks/                                 [Kernel PMU event]
> > +  cpmu0/d2h_req_itomwr/                              [Kernel PMU event]
> > +  cpmu0/d2h_req_rdany/                               [Kernel PMU event]
> > +  cpmu0/d2h_req_rdcurr/                              [Kernel PMU event]
> > +  -----------------------------------------------------------
> > +
> > +  $# perf stat -e cpmu0/clock_ticks/ -e cpmu0/d2h_req_itowrm/
> > +
> > +Vendor specific events may also be available and if so can be used via
> > +
> > +  $# perf stat -e cpmu0/vid=VID,gid=GID,mask=MASK/
> > +
> > +The driver does not support sampling. So "perf record" and attaching to
> > +a task are unsupported.  
> 
> The PMU only supports system-wide counting. That's the reason it doesn't
> support per-task profiling. Not because of missing sampling.

Ah. I've managed to fuse two different conditions. I'll break them apart for
v5.

Thanks,

Jonathan

> 
> Thanks,
> Kan
> > diff --git a/Documentation/admin-guide/perf/index.rst b/Documentation/admin-guide/perf/index.rst
> > index 9de64a40adab..f60be04e4e33 100644
> > --- a/Documentation/admin-guide/perf/index.rst
> > +++ b/Documentation/admin-guide/perf/index.rst
> > @@ -21,3 +21,4 @@ Performance monitor support
> >     alibaba_pmu
> >     nvidia-pmu
> >     meson-ddr-pmu
> > +   cxl  
>
Dan Williams April 4, 2023, 10:24 p.m. UTC | #3
Jonathan Cameron wrote:
> Very basic introduction to the device and the current driver support
> provided. I expect to expand on this in future versions of this patch
> set.
> 
> Reviewed-by: Dave Jiang <dave.jiang@intel.com>
> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> 
> --
> v4: No change
> ---
>  Documentation/admin-guide/perf/cxl.rst   | 65 ++++++++++++++++++++++++
>  Documentation/admin-guide/perf/index.rst |  1 +
>  2 files changed, 66 insertions(+)
> 
> diff --git a/Documentation/admin-guide/perf/cxl.rst b/Documentation/admin-guide/perf/cxl.rst
> new file mode 100644
> index 000000000000..46235dff4b21
> --- /dev/null
> +++ b/Documentation/admin-guide/perf/cxl.rst
> @@ -0,0 +1,65 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +======================================
> +CXL Performance Monitoring Unit (CPMU)
> +======================================
> +
> +The CXL rev 3.0 specification provides a definition of CXL Performance
> +Monitoring Unit in section 13.2: Performance Monitoring.
> +
> +CXL components (e.g. Root Port, Switch Upstream Port, End Point) may have
> +any number of CPMU instances. CPMU capabilities are fully discoverable from
> +the devices. The specification provides event definitions for all CXL protocol
> +message types and a set of additional events for things commonly counted on
> +CXL devices (e.g. DRAM events).
> +
> +CPMU driver
> +===========
> +
> +The CPMU driver register a perf PMU with the name cpmu<id> on the CXL bus.

s/register/registers/

> +
> +    /sys/bus/cxl/device/cpmu<id>
> +
> +The associated PMU is registered as
> +
> +   /sys/bus/event_sources/devices/cpmu<id>
> +
> +In common with other CXL bus devices, the id has no specific meaning and the
> +relationship to specific CXL device should be established via the device parent
> +of the device on the CXL bus.

So I went to go add some text about how to identify PMUs in a persistent
manner from one boot to the next. For CXL memdevs this is done by the
'serial' attribute which is always stable regardless of the device init
order. That's harder to get to from the pmu device because it may be
associated with a device that does not have a memdev.

I think it's also going to be frustrating for userspace to see
randomized pmu ids across devices since that probing will happen in
parallel. So how about:

1/ Add serial as an attribute for each PMU to export
2/ Change the device name format to be "pmuX.Y" where X can just reuse
the memdev id for endpoints and be another value for switches, and Y is
guaranteed to be 0-based and in hardware discovery order.

...with that, someone can write a udev script that can persistently
identify PMU[Y] on device[serial] each boot.

That also cleans up a /sys/bus/cxl/devices listing to make it clear
which pmu instances belong together.
 
> +
> +PMU driver provides description of available events and filter options in sysfs.
> +
> +The "format" directory describes all formats of the config (event vendor id,
> +group id and mask) config1 (threshold, filter enables) and config2 (filter
> +parameters) fields of the perf_event_attr structure.  The "events" directory
> +describes all documented events show in perf list.
> +
> +The events shown in perf list are the most fine grained events with a single
> +bit of the event mask set. More general events may be enable by setting
> +multiple mask bits in config. For example, all Device to Host Read Requests
> +may be captured on a single counter by setting the bits for all of
> +
> +* d2h_req_rdcurr
> +* d2h_req_rdown
> +* d2h_req_rdshared
> +* d2h_req_rdany
> +* d2h_req_rdownnodata
> +
> +Example of usage::
> +
> +  $#perf list
> +  cpmu0/clock_ticks/                                 [Kernel PMU event]
> +  cpmu0/d2h_req_itomwr/                              [Kernel PMU event]
> +  cpmu0/d2h_req_rdany/                               [Kernel PMU event]
> +  cpmu0/d2h_req_rdcurr/                              [Kernel PMU event]
> +  -----------------------------------------------------------
> +
> +  $# perf stat -e cpmu0/clock_ticks/ -e cpmu0/d2h_req_itowrm/

Ah here's the examples I was looking for in the last patch, nice.

> +
> +Vendor specific events may also be available and if so can be used via
> +
> +  $# perf stat -e cpmu0/vid=VID,gid=GID,mask=MASK/
> +
> +The driver does not support sampling. So "perf record" and attaching to
> +a task are unsupported.

Is this a common restriction for CPU-external pmus, or do you see
sampling support required to get this upstream?
Jonathan Cameron April 6, 2023, 4:33 p.m. UTC | #4
> 
> > +
> > +    /sys/bus/cxl/device/cpmu<id>
> > +
> > +The associated PMU is registered as
> > +
> > +   /sys/bus/event_sources/devices/cpmu<id>
> > +
> > +In common with other CXL bus devices, the id has no specific meaning and the
> > +relationship to specific CXL device should be established via the device parent
> > +of the device on the CXL bus.  
> 
> So I went to go add some text about how to identify PMUs in a persistent
> manner from one boot to the next. For CXL memdevs this is done by the
> 'serial' attribute which is always stable regardless of the device init
> order. That's harder to get to from the pmu device because it may be
> associated with a device that does not have a memdev.
> 
> I think it's also going to be frustrating for userspace to see
> randomized pmu ids across devices since that probing will happen in
> parallel. So how about:

Solving this in general for perf PMU drivers was what the parent device thing
was about.  There is an argument that enabling any other path to get to
this association is both unnecessary and just possibly unwise.

The nice advantage of just using an IDA and relying on parentage for the
association was that I could avoid naming questions for all the other
places these might turn in a CXL topology. The Lazy / efficient option ;)

You can now see exactly which PCI device a given instance is associated with.
Custom ABI is going to be harder for anyone to use than that.

I suppose we can potentially enable both paths - but it's not quite
as straight forwards as you suggest.

> 
> 1/ Add serial as an attribute for each PMU to export

Where does it come from? We only have one source of serial number per device.
That's no where near enough to work out where a PMU is. 

> 2/ Change the device name format to be "pmuX.Y" where X can just reuse

Could use something a little more detailed cxl bus, but the one registered and use
to address this in bus/event_sources needs to be cxl specific so a cxl_ prefix
is needed I think

Given we need to namespace what the ids refer to, I'm currently going with
pmu_memX.Y pmu_dspX.Y.Z pmu_uspX.Y
on the cxl bus and
cxl_pmu_memX.Y cxl_pmu_dspX.Y.Z cxl_pmu_uspX.Y on even sources bus.
(Z needed because dsp index from 0 for each usp)
We can figure out what to do about other CXL EPs later and for now at least
there is no way to hand a CPMU instance off a host bridge (nothing in CEDT
to tell you where to find it).

I've had a fun day hacking PMUs onto the other emulated CXL devices to test
this. 
There is a can of worms I'll avoid for this series by just sticking to type3
device PMUs for now.

  I have no idea yet how we handle the interrupts safely for ports as those
  interrupts are in control the pcie port driver not the CXL dport one.
  At somepoint I'll send out an RFC about that if no one gets to it before
  me.  For now I've hacked portdrv to always allocate max vectors and am ignoring the
  lovely back traces due to thing getting torn down in the wrong order on shutdown.
  For upstream ports I've hacked portdrv to pretend it knows there is something to handle.
  As a starting point I think we'll need to teach portdrv enough about CXL
  to be able to tell if it should provide interrupt services..

Hence I'll keep the code to register the other PMUs for a future patch set
and just make sure the code is structured to enable that in this series.


> the memdev id for endpoints and be another value for switches, and Y is
> guaranteed to be 0-based and in hardware discovery order.

Also need to change registration order as PMUs were registered before the
memdev, but that's easy enough to do.

> 
> ...with that, someone can write a udev script that can persistently
> identify PMU[Y] on device[serial] each boot.

> 
> That also cleans up a /sys/bus/cxl/devices listing to make it clear
> which pmu instances belong together.
>  
> > +
> > +PMU driver provides description of available events and filter options in sysfs.
> > +
> > +The "format" directory describes all formats of the config (event vendor id,
> > +group id and mask) config1 (threshold, filter enables) and config2 (filter
> > +parameters) fields of the perf_event_attr structure.  The "events" directory
> > +describes all documented events show in perf list.
> > +
> > +The events shown in perf list are the most fine grained events with a single
> > +bit of the event mask set. More general events may be enable by setting
> > +multiple mask bits in config. For example, all Device to Host Read Requests
> > +may be captured on a single counter by setting the bits for all of
> > +
> > +* d2h_req_rdcurr
> > +* d2h_req_rdown
> > +* d2h_req_rdshared
> > +* d2h_req_rdany
> > +* d2h_req_rdownnodata
> > +
> > +Example of usage::
> > +
> > +  $#perf list
> > +  cpmu0/clock_ticks/                                 [Kernel PMU event]
> > +  cpmu0/d2h_req_itomwr/                              [Kernel PMU event]
> > +  cpmu0/d2h_req_rdany/                               [Kernel PMU event]
> > +  cpmu0/d2h_req_rdcurr/                              [Kernel PMU event]
> > +  -----------------------------------------------------------
> > +
> > +  $# perf stat -e cpmu0/clock_ticks/ -e cpmu0/d2h_req_itowrm/  
> 
> Ah here's the examples I was looking for in the last patch, nice.
> 
> > +
> > +Vendor specific events may also be available and if so can be used via
> > +
> > +  $# perf stat -e cpmu0/vid=VID,gid=GID,mask=MASK/
> > +
> > +The driver does not support sampling. So "perf record" and attaching to
> > +a task are unsupported.  
> 
> Is this a common restriction for CPU-external pmus, or do you see
> sampling support required to get this upstream?

It's a common restriction. Whilst we could potentially implement sampling
based on the presence of a suitable clock_ticks event it don't see it
as a requirement initially.

Jonathan
diff mbox series

Patch

diff --git a/Documentation/admin-guide/perf/cxl.rst b/Documentation/admin-guide/perf/cxl.rst
new file mode 100644
index 000000000000..46235dff4b21
--- /dev/null
+++ b/Documentation/admin-guide/perf/cxl.rst
@@ -0,0 +1,65 @@ 
+.. SPDX-License-Identifier: GPL-2.0
+
+======================================
+CXL Performance Monitoring Unit (CPMU)
+======================================
+
+The CXL rev 3.0 specification provides a definition of CXL Performance
+Monitoring Unit in section 13.2: Performance Monitoring.
+
+CXL components (e.g. Root Port, Switch Upstream Port, End Point) may have
+any number of CPMU instances. CPMU capabilities are fully discoverable from
+the devices. The specification provides event definitions for all CXL protocol
+message types and a set of additional events for things commonly counted on
+CXL devices (e.g. DRAM events).
+
+CPMU driver
+===========
+
+The CPMU driver register a perf PMU with the name cpmu<id> on the CXL bus.
+
+    /sys/bus/cxl/device/cpmu<id>
+
+The associated PMU is registered as
+
+   /sys/bus/event_sources/devices/cpmu<id>
+
+In common with other CXL bus devices, the id has no specific meaning and the
+relationship to specific CXL device should be established via the device parent
+of the device on the CXL bus.
+
+PMU driver provides description of available events and filter options in sysfs.
+
+The "format" directory describes all formats of the config (event vendor id,
+group id and mask) config1 (threshold, filter enables) and config2 (filter
+parameters) fields of the perf_event_attr structure.  The "events" directory
+describes all documented events show in perf list.
+
+The events shown in perf list are the most fine grained events with a single
+bit of the event mask set. More general events may be enable by setting
+multiple mask bits in config. For example, all Device to Host Read Requests
+may be captured on a single counter by setting the bits for all of
+
+* d2h_req_rdcurr
+* d2h_req_rdown
+* d2h_req_rdshared
+* d2h_req_rdany
+* d2h_req_rdownnodata
+
+Example of usage::
+
+  $#perf list
+  cpmu0/clock_ticks/                                 [Kernel PMU event]
+  cpmu0/d2h_req_itomwr/                              [Kernel PMU event]
+  cpmu0/d2h_req_rdany/                               [Kernel PMU event]
+  cpmu0/d2h_req_rdcurr/                              [Kernel PMU event]
+  -----------------------------------------------------------
+
+  $# perf stat -e cpmu0/clock_ticks/ -e cpmu0/d2h_req_itowrm/
+
+Vendor specific events may also be available and if so can be used via
+
+  $# perf stat -e cpmu0/vid=VID,gid=GID,mask=MASK/
+
+The driver does not support sampling. So "perf record" and attaching to
+a task are unsupported.
diff --git a/Documentation/admin-guide/perf/index.rst b/Documentation/admin-guide/perf/index.rst
index 9de64a40adab..f60be04e4e33 100644
--- a/Documentation/admin-guide/perf/index.rst
+++ b/Documentation/admin-guide/perf/index.rst
@@ -21,3 +21,4 @@  Performance monitor support
    alibaba_pmu
    nvidia-pmu
    meson-ddr-pmu
+   cxl