| Message ID | 20230406-topic-lenovo_features-v1-4-c73a5180e48e@linaro.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Tab P11 features | expand |
On 06/04/2023 18:25, Konrad Dybcio wrote: > Enable the onboard QCA Wi-Fi. HW identifiers for reference: > qmi chip_id 0x320 chip_family 0x4001 board_id 0xff soc_id 0x400e0000 > > Firmware sources: > /vendor/firmware_mnt/image/wlanmdsp.bin -> qcom/.../wlanmdsp.mbn > /vendor/firmware_mnt/image/bdwlan.bXX [1] -> [2] -> ath10k/.../board-2.bin > [3] -> ath10k/.../firmware-5.bin > > Not sure where 3 comes from on the device itself, gotta investigate that.. > > According to [4], it's called WCN3990_STRAIT. > > [1] XX = board_id printed when the file is missing or by your downstream > kernel firmware loader in the dmesg; if XX=ff, use bdwlan.bin Since the board_id is 0xff, please add qcom,ath10k-calibration-variant Ideally, could you please send the bdwlan to ath10k for inclusion, see https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles . > > [2] https://github.com/jhugo/linux/blob/5.5rc2_wifi/README > [3] https://github.com/kvalo/ath10k-firmware/blob/master/WCN3990/hw1.0/HL3.1/WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1/firmware-5.bin > [4] https://git.codelinaro.org/clo/la/platform/vendor/qcom-opensource/wlan/qca-wifi-host-cmn/-/blob/LA.VENDOR.1.0.r1-20700-WAIPIO.QSSI13.0/hif/src/hif_hw_version.h#L55 > > Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> > --- > arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts | 8 ++++++++ > 1 file changed, 8 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts > index 2aac25171dec..4ba8e59a27d8 100644 > --- a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts > +++ b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts > @@ -315,6 +315,14 @@ &usb_hsphy { > status = "okay"; > }; > > +&wifi { > + vdd-0.8-cx-mx-supply = <&pm6125_l8>; > + vdd-1.8-xo-supply = <&pm6125_l16>; > + vdd-1.3-rfa-supply = <&pm6125_l17>; > + vdd-3.3-ch0-supply = <&pm6125_l23>; > + status = "okay"; > +}; > + > &xo_board { > clock-frequency = <19200000>; > }; >
On 6.04.2023 19:51, Dmitry Baryshkov wrote: > On 06/04/2023 18:25, Konrad Dybcio wrote: >> Enable the onboard QCA Wi-Fi. HW identifiers for reference: >> qmi chip_id 0x320 chip_family 0x4001 board_id 0xff soc_id 0x400e0000 >> >> Firmware sources: >> /vendor/firmware_mnt/image/wlanmdsp.bin -> qcom/.../wlanmdsp.mbn >> /vendor/firmware_mnt/image/bdwlan.bXX [1] -> [2] -> ath10k/.../board-2.bin >> [3] -> ath10k/.../firmware-5.bin >> >> Not sure where 3 comes from on the device itself, gotta investigate that.. >> >> According to [4], it's called WCN3990_STRAIT. >> >> [1] XX = board_id printed when the file is missing or by your downstream >> kernel firmware loader in the dmesg; if XX=ff, use bdwlan.bin > > Since the board_id is 0xff, please add qcom,ath10k-calibration-variant Do I make up a name, or is there some convention? I see Johan used "LE_X13S" in commit 2702f54f400ad3979632cdb76553772414f4c5e3. Should I go with "LE_P11"? > > Ideally, could you please send the bdwlan to ath10k for inclusion, see https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles . The legal situation is ambiguous at best :/ Konrad > >> >> [2] https://github.com/jhugo/linux/blob/5.5rc2_wifi/README >> [3] https://github.com/kvalo/ath10k-firmware/blob/master/WCN3990/hw1.0/HL3.1/WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1/firmware-5.bin >> [4] https://git.codelinaro.org/clo/la/platform/vendor/qcom-opensource/wlan/qca-wifi-host-cmn/-/blob/LA.VENDOR.1.0.r1-20700-WAIPIO.QSSI13.0/hif/src/hif_hw_version.h#L55 >> >> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> >> --- >> arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts | 8 ++++++++ >> 1 file changed, 8 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts >> index 2aac25171dec..4ba8e59a27d8 100644 >> --- a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts >> +++ b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts >> @@ -315,6 +315,14 @@ &usb_hsphy { >> status = "okay"; >> }; >> +&wifi { >> + vdd-0.8-cx-mx-supply = <&pm6125_l8>; >> + vdd-1.8-xo-supply = <&pm6125_l16>; >> + vdd-1.3-rfa-supply = <&pm6125_l17>; >> + vdd-3.3-ch0-supply = <&pm6125_l23>; >> + status = "okay"; >> +}; >> + >> &xo_board { >> clock-frequency = <19200000>; >> }; >> >
On Thu, 6 Apr 2023 at 21:32, Konrad Dybcio <konrad.dybcio@linaro.org> wrote: > > > > On 6.04.2023 19:51, Dmitry Baryshkov wrote: > > On 06/04/2023 18:25, Konrad Dybcio wrote: > >> Enable the onboard QCA Wi-Fi. HW identifiers for reference: > >> qmi chip_id 0x320 chip_family 0x4001 board_id 0xff soc_id 0x400e0000 > >> > >> Firmware sources: > >> /vendor/firmware_mnt/image/wlanmdsp.bin -> qcom/.../wlanmdsp.mbn > >> /vendor/firmware_mnt/image/bdwlan.bXX [1] -> [2] -> ath10k/.../board-2.bin > >> [3] -> ath10k/.../firmware-5.bin > >> > >> Not sure where 3 comes from on the device itself, gotta investigate that.. > >> > >> According to [4], it's called WCN3990_STRAIT. > >> > >> [1] XX = board_id printed when the file is missing or by your downstream > >> kernel firmware loader in the dmesg; if XX=ff, use bdwlan.bin > > > > Since the board_id is 0xff, please add qcom,ath10k-calibration-variant > Do I make up a name, or is there some convention? > > I see Johan used "LE_X13S" in commit 2702f54f400ad3979632cdb76553772414f4c5e3. > Should I go with "LE_P11"? I think Lenovo_P11 or LENOVO_P11 might be better. > > > > > Ideally, could you please send the bdwlan to ath10k for inclusion, see https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles . > The legal situation is ambiguous at best :/ As usual :-( > > Konrad > > > >> > >> [2] https://github.com/jhugo/linux/blob/5.5rc2_wifi/README > >> [3] https://github.com/kvalo/ath10k-firmware/blob/master/WCN3990/hw1.0/HL3.1/WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1/firmware-5.bin > >> [4] https://git.codelinaro.org/clo/la/platform/vendor/qcom-opensource/wlan/qca-wifi-host-cmn/-/blob/LA.VENDOR.1.0.r1-20700-WAIPIO.QSSI13.0/hif/src/hif_hw_version.h#L55 > >> > >> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> > >> --- > >> arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts | 8 ++++++++ > >> 1 file changed, 8 insertions(+) > >> > >> diff --git a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts > >> index 2aac25171dec..4ba8e59a27d8 100644 > >> --- a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts > >> +++ b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts > >> @@ -315,6 +315,14 @@ &usb_hsphy { > >> status = "okay"; > >> }; > >> +&wifi { > >> + vdd-0.8-cx-mx-supply = <&pm6125_l8>; > >> + vdd-1.8-xo-supply = <&pm6125_l16>; > >> + vdd-1.3-rfa-supply = <&pm6125_l17>; > >> + vdd-3.3-ch0-supply = <&pm6125_l23>; > >> + status = "okay"; > >> +}; > >> + > >> &xo_board { > >> clock-frequency = <19200000>; > >> }; > >> > >
On 06/04/2023 21:56, Dmitry Baryshkov wrote: > On Thu, 6 Apr 2023 at 21:32, Konrad Dybcio <konrad.dybcio@linaro.org> wrote: >> >> >> >> On 6.04.2023 19:51, Dmitry Baryshkov wrote: >>> On 06/04/2023 18:25, Konrad Dybcio wrote: >>>> Enable the onboard QCA Wi-Fi. HW identifiers for reference: >>>> qmi chip_id 0x320 chip_family 0x4001 board_id 0xff soc_id 0x400e0000 >>>> >>>> Firmware sources: >>>> /vendor/firmware_mnt/image/wlanmdsp.bin -> qcom/.../wlanmdsp.mbn >>>> /vendor/firmware_mnt/image/bdwlan.bXX [1] -> [2] -> ath10k/.../board-2.bin >>>> [3] -> ath10k/.../firmware-5.bin >>>> >>>> Not sure where 3 comes from on the device itself, gotta investigate that.. >>>> >>>> According to [4], it's called WCN3990_STRAIT. >>>> >>>> [1] XX = board_id printed when the file is missing or by your downstream >>>> kernel firmware loader in the dmesg; if XX=ff, use bdwlan.bin >>> >>> Since the board_id is 0xff, please add qcom,ath10k-calibration-variant >> Do I make up a name, or is there some convention? >> >> I see Johan used "LE_X13S" in commit 2702f54f400ad3979632cdb76553772414f4c5e3. >> Should I go with "LE_P11"? > > I think Lenovo_P11 or LENOVO_P11 might be better. An update here: Kalle added a board file for Yoga C630 using the id 'bus=snoc,qmi-board-id=ff,qmi-chip-id=30214,variant=Lenovo_C630'. So, I think, we should use 'Lenovo_P11' here. > >> >>> >>> Ideally, could you please send the bdwlan to ath10k for inclusion, see https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles . >> The legal situation is ambiguous at best :/ > > As usual :-( > >> >> Konrad >>> >>>> >>>> [2] https://github.com/jhugo/linux/blob/5.5rc2_wifi/README >>>> [3] https://github.com/kvalo/ath10k-firmware/blob/master/WCN3990/hw1.0/HL3.1/WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1/firmware-5.bin >>>> [4] https://git.codelinaro.org/clo/la/platform/vendor/qcom-opensource/wlan/qca-wifi-host-cmn/-/blob/LA.VENDOR.1.0.r1-20700-WAIPIO.QSSI13.0/hif/src/hif_hw_version.h#L55 >>>> >>>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> >>>> --- >>>> arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts | 8 ++++++++ >>>> 1 file changed, 8 insertions(+) >>>> >>>> diff --git a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts >>>> index 2aac25171dec..4ba8e59a27d8 100644 >>>> --- a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts >>>> +++ b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts >>>> @@ -315,6 +315,14 @@ &usb_hsphy { >>>> status = "okay"; >>>> }; >>>> +&wifi { >>>> + vdd-0.8-cx-mx-supply = <&pm6125_l8>; >>>> + vdd-1.8-xo-supply = <&pm6125_l16>; >>>> + vdd-1.3-rfa-supply = <&pm6125_l17>; >>>> + vdd-3.3-ch0-supply = <&pm6125_l23>; >>>> + status = "okay"; >>>> +}; >>>> + >>>> &xo_board { >>>> clock-frequency = <19200000>; >>>> }; >>>> >>> > > >
diff --git a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts index 2aac25171dec..4ba8e59a27d8 100644 --- a/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts +++ b/arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts @@ -315,6 +315,14 @@ &usb_hsphy { status = "okay"; }; +&wifi { + vdd-0.8-cx-mx-supply = <&pm6125_l8>; + vdd-1.8-xo-supply = <&pm6125_l16>; + vdd-1.3-rfa-supply = <&pm6125_l17>; + vdd-3.3-ch0-supply = <&pm6125_l23>; + status = "okay"; +}; + &xo_board { clock-frequency = <19200000>; };
Enable the onboard QCA Wi-Fi. HW identifiers for reference: qmi chip_id 0x320 chip_family 0x4001 board_id 0xff soc_id 0x400e0000 Firmware sources: /vendor/firmware_mnt/image/wlanmdsp.bin -> qcom/.../wlanmdsp.mbn /vendor/firmware_mnt/image/bdwlan.bXX [1] -> [2] -> ath10k/.../board-2.bin [3] -> ath10k/.../firmware-5.bin Not sure where 3 comes from on the device itself, gotta investigate that.. According to [4], it's called WCN3990_STRAIT. [1] XX = board_id printed when the file is missing or by your downstream kernel firmware loader in the dmesg; if XX=ff, use bdwlan.bin [2] https://github.com/jhugo/linux/blob/5.5rc2_wifi/README [3] https://github.com/kvalo/ath10k-firmware/blob/master/WCN3990/hw1.0/HL3.1/WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1/firmware-5.bin [4] https://git.codelinaro.org/clo/la/platform/vendor/qcom-opensource/wlan/qca-wifi-host-cmn/-/blob/LA.VENDOR.1.0.r1-20700-WAIPIO.QSSI13.0/hif/src/hif_hw_version.h#L55 Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> --- arch/arm64/boot/dts/qcom/sm6115p-lenovo-j606f.dts | 8 ++++++++ 1 file changed, 8 insertions(+)