| Message ID | 20230411184313.3679145-4-sean.anderson@seco.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | phy: Add support for Lynx 10G SerDes | expand |
On Tue, 11 Apr 2023 14:43:00 -0400, Sean Anderson wrote: > This is a generic binding for simple MMIO GPIO controllers. Although we > have a single driver for these controllers, they were previously spread > over several files. Consolidate them. The register descriptions are > adapted from the comments in the source. There is no set order for the > registers, and some registers may be omitted. Because of this, reg-names > is mandatory, and no order is specified. > > Rename brcm,bcm6345-gpio to brcm,bcm63xx-gpio to reflect that bcm6345 > has moved. > > Signed-off-by: Sean Anderson <sean.anderson@seco.com> > Reviewed-by: Linus Walleij <linus.walleij@linaro.org> > --- > Linus or Bartosz, feel free to pick this up as the rest of this series > may not be merged any time soon. > > Changes in v13: > - Fix references to brcm,bcm63xx-gpio.yaml (neé brcm,bcm6345-gpio) > > Changes in v12: > - Put compatible first > - Keep gpio-controller to one line > - Add little-endian property > - Alphabetize compatibles > - Remove some comments > - Remove some examples with insufficient novelty > > Changes in v11: > - Keep empty (or almost-empty) properties on a single line > - Don't use | unnecessarily > - Use gpio as the node name for examples > - Rename brcm,bcm6345-gpio.yaml to brcm,bcm63xx-gpio.yaml > > Changes in v10: > - New > > ...m6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} | 16 +-- > .../devicetree/bindings/gpio/gpio-mmio.yaml | 117 ++++++++++++++++++ > .../bindings/gpio/ni,169445-nand-gpio.txt | 38 ------ > .../devicetree/bindings/gpio/wd,mbl-gpio.txt | 38 ------ > .../mfd/brcm,bcm6318-gpio-sysctl.yaml | 4 +- > .../mfd/brcm,bcm63268-gpio-sysctl.yaml | 4 +- > .../mfd/brcm,bcm6328-gpio-sysctl.yaml | 4 +- > .../mfd/brcm,bcm6358-gpio-sysctl.yaml | 4 +- > .../mfd/brcm,bcm6362-gpio-sysctl.yaml | 4 +- > .../mfd/brcm,bcm6368-gpio-sysctl.yaml | 4 +- > 10 files changed, 130 insertions(+), 103 deletions(-) > rename Documentation/devicetree/bindings/gpio/{brcm,bcm6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} (78%) > create mode 100644 Documentation/devicetree/bindings/gpio/gpio-mmio.yaml > delete mode 100644 Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt > delete mode 100644 Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: ./Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml: $id: relative path/filename doesn't match actual path or filename expected: http://devicetree.org/schemas/gpio/brcm,bcm63xx-gpio.yaml# /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.example.dtb: syscon@10000080: gpio@0: False schema does not allow {'compatible': ['brcm,bcm6318-gpio'], 'reg-names': ['dirout', 'dat'], 'reg': [[0, 8], [8, 8]], 'gpio-controller': True, 'gpio-ranges': [[1, 0, 0, 50]], '#gpio-cells': [[2]]} From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm63268-gpio-sysctl.example.dtb: syscon@100000c0: gpio@0: False schema does not allow {'compatible': ['brcm,bcm63268-gpio'], 'reg-names': ['dirout', 'dat'], 'reg': [[0, 8], [8, 8]], 'gpio-controller': True, 'gpio-ranges': [[1, 0, 0, 52]], '#gpio-cells': [[2]]} From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm63268-gpio-sysctl.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6362-gpio-sysctl.example.dtb: syscon@10000080: gpio@0: False schema does not allow {'compatible': ['brcm,bcm6362-gpio'], 'reg-names': ['dirout', 'dat'], 'reg': [[0, 8], [8, 8]], 'gpio-controller': True, 'gpio-ranges': [[1, 0, 0, 48]], '#gpio-cells': [[2]]} From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6362-gpio-sysctl.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6328-gpio-sysctl.example.dtb: syscon@10000080: gpio@0: False schema does not allow {'compatible': ['brcm,bcm6328-gpio'], 'reg-names': ['dirout', 'dat'], 'reg': [[0, 8], [8, 8]], 'gpio-controller': True, 'gpio-ranges': [[1, 0, 0, 32]], '#gpio-cells': [[2]]} From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6328-gpio-sysctl.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6358-gpio-sysctl.example.dtb: syscon@fffe0080: gpio@0: False schema does not allow {'compatible': ['brcm,bcm6358-gpio'], 'reg-names': ['dirout', 'dat'], 'reg': [[0, 8], [8, 8]], 'gpio-controller': True, 'gpio-ranges': [[1, 0, 0, 40]], '#gpio-cells': [[2]]} From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6358-gpio-sysctl.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6368-gpio-sysctl.example.dtb: syscon@10000080: gpio@0: False schema does not allow {'compatible': ['brcm,bcm6368-gpio'], 'reg-names': ['dirout', 'dat'], 'reg': [[0, 8], [8, 8]], 'gpio-controller': True, 'gpio-ranges': [[1, 0, 0, 38]], '#gpio-cells': [[2]]} From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6368-gpio-sysctl.yaml doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230411184313.3679145-4-sean.anderson@seco.com The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema.
On 11/04/2023 20:43, Sean Anderson wrote: > This is a generic binding for simple MMIO GPIO controllers. Although we > have a single driver for these controllers, they were previously spread > over several files. Consolidate them. The register descriptions are > adapted from the comments in the source. There is no set order for the > registers, and some registers may be omitted. Because of this, reg-names > is mandatory, and no order is specified. > > Rename brcm,bcm6345-gpio to brcm,bcm63xx-gpio to reflect that bcm6345 > has moved. > > Signed-off-by: Sean Anderson <sean.anderson@seco.com> > Reviewed-by: Linus Walleij <linus.walleij@linaro.org> > --- > Linus or Bartosz, feel free to pick this up as the rest of this series > may not be merged any time soon. > > Changes in v13: > - Fix references to brcm,bcm63xx-gpio.yaml (neé brcm,bcm6345-gpio) You got some of the same errors as last time. Test your patches before sending. Best regards, Krzysztof
On 4/12/23 04:04, Krzysztof Kozlowski wrote: > On 11/04/2023 20:43, Sean Anderson wrote: >> This is a generic binding for simple MMIO GPIO controllers. Although we >> have a single driver for these controllers, they were previously spread >> over several files. Consolidate them. The register descriptions are >> adapted from the comments in the source. There is no set order for the >> registers, and some registers may be omitted. Because of this, reg-names >> is mandatory, and no order is specified. >> >> Rename brcm,bcm6345-gpio to brcm,bcm63xx-gpio to reflect that bcm6345 >> has moved. >> >> Signed-off-by: Sean Anderson <sean.anderson@seco.com> >> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> >> --- >> Linus or Bartosz, feel free to pick this up as the rest of this series >> may not be merged any time soon. >> >> Changes in v13: >> - Fix references to brcm,bcm63xx-gpio.yaml (neé brcm,bcm6345-gpio) > > You got some of the same errors as last time. These are different errors. > Test your patches before sending. I typically run dt_bindings_check with DT_SCHEMA_FILES=... because running the whole thing takes longer than compiling a kernel from scratch. It seems I neglected to run it on the affected schemas. --Sean
diff --git a/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml b/Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml similarity index 78% rename from Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml rename to Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml index 4d69f79df859..e11f4af49c52 100644 --- a/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml +++ b/Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/gpio/brcm,bcm6345-gpio.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Broadcom BCM6345 GPIO controller +title: Broadcom BCM63xx GPIO controller maintainers: - Álvaro Fernández Rojas <noltari@gmail.com> @@ -18,8 +18,6 @@ description: |+ BCM6338 have 8-bit data and dirout registers, where GPIO state can be read and/or written, and the direction changed from input to output. - BCM6345 have 16-bit data and dirout registers, where GPIO state can be read - and/or written, and the direction changed from input to output. BCM6318, BCM6328, BCM6358, BCM6362, BCM6368 and BCM63268 have 32-bit data and dirout registers, where GPIO state can be read and/or written, and the direction changed from input to output. @@ -29,7 +27,6 @@ properties: enum: - brcm,bcm6318-gpio - brcm,bcm6328-gpio - - brcm,bcm6345-gpio - brcm,bcm6358-gpio - brcm,bcm6362-gpio - brcm,bcm6368-gpio @@ -63,17 +60,6 @@ required: additionalProperties: false examples: - - | - gpio@fffe0406 { - compatible = "brcm,bcm6345-gpio"; - reg-names = "dirout", "dat"; - reg = <0xfffe0406 2>, <0xfffe040a 2>; - native-endian; - - gpio-controller; - #gpio-cells = <2>; - }; - - | gpio@0 { compatible = "brcm,bcm63268-gpio"; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mmio.yaml b/Documentation/devicetree/bindings/gpio/gpio-mmio.yaml new file mode 100644 index 000000000000..b394e058256e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mmio.yaml @@ -0,0 +1,117 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/gpio-mmio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic MMIO GPIO + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + - Bartosz Golaszewski <brgl@bgdev.pl> + +description: + Some simple GPIO controllers may consist of a single data register or a pair + of set/clear-bit registers. Such controllers are common for glue logic in + FPGAs or ASICs. Commonly, these controllers are accessed over memory-mapped + NAND-style parallel busses. + +properties: + compatible: + enum: + - brcm,bcm6345-gpio + - ni,169445-nand-gpio + - wd,mbl-gpio # Western Digital MyBook Live memory-mapped GPIO controller + + big-endian: true + + '#gpio-cells': + const: 2 + + gpio-controller: true + + little-endian: true + + reg: + minItems: 1 + description: + A list of registers in the controller. The width of each register is + determined by its size. All registers must have the same width. The number + of GPIOs is set by the width, with bit 0 corresponding to GPIO 0. + items: + - description: + Register to READ the value of the GPIO lines. If GPIO line is high, + the bit will be set. If the GPIO line is low, the bit will be cleared. + This register may also be used to drive GPIOs if the SET register is + omitted. + - description: + Register to SET the value of the GPIO lines. Setting a bit in this + register will drive the GPIO line high. + - description: + Register to CLEAR the value of the GPIO lines. Setting a bit in this + register will drive the GPIO line low. If this register is omitted, + the SET register will be used to clear the GPIO lines as well, by + actively writing the line with 0. + - description: + Register to set the line as OUTPUT. Setting a bit in this register + will turn that line into an output line. Conversely, clearing a bit + will turn that line into an input. + - description: + Register to set this line as INPUT. Setting a bit in this register + will turn that line into an input line. Conversely, clearing a bit + will turn that line into an output. + + reg-names: + minItems: 1 + maxItems: 5 + items: + enum: + - dat + - set + - clr + - dirout + - dirin + + native-endian: true + + no-output: + $ref: /schemas/types.yaml#/definitions/flag + description: + If this property is present, the controller cannot drive the GPIO lines. + +required: + - compatible + - reg + - reg-names + - '#gpio-cells' + - gpio-controller + +additionalProperties: false + +examples: + - | + gpio@1f300010 { + compatible = "ni,169445-nand-gpio"; + reg = <0x1f300010 0x4>; + reg-names = "dat"; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@e0100000 { + compatible = "wd,mbl-gpio"; + reg-names = "dat"; + reg = <0xe0100000 0x1>; + #gpio-cells = <2>; + gpio-controller; + no-output; + }; + + gpio@fffe0406 { + compatible = "brcm,bcm6345-gpio"; + reg-names = "dirout", "dat"; + reg = <0xfffe0406 2>, <0xfffe040a 2>; + native-endian; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt b/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt deleted file mode 100644 index ca2f8c745a27..000000000000 --- a/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt +++ /dev/null @@ -1,38 +0,0 @@ -Bindings for the National Instruments 169445 GPIO NAND controller - -The 169445 GPIO NAND controller has two memory mapped GPIO registers, one -for input (the ready signal) and one for output (control signals). It is -intended to be used with the GPIO NAND driver. - -Required properties: - - compatible: should be "ni,169445-nand-gpio" - - reg-names: must contain - "dat" - data register - - reg: address + size pairs describing the GPIO register sets; - order must correspond with the order of entries in reg-names - - #gpio-cells: must be set to 2. The first cell is the pin number and - the second cell is used to specify the gpio polarity: - 0 = active high - 1 = active low - - gpio-controller: Marks the device node as a gpio controller. - -Optional properties: - - no-output: disables driving output on the pins - -Examples: - gpio1: nand-gpio-out@1f300010 { - compatible = "ni,169445-nand-gpio"; - reg = <0x1f300010 0x4>; - reg-names = "dat"; - gpio-controller; - #gpio-cells = <2>; - }; - - gpio2: nand-gpio-in@1f300014 { - compatible = "ni,169445-nand-gpio"; - reg = <0x1f300014 0x4>; - reg-names = "dat"; - gpio-controller; - #gpio-cells = <2>; - no-output; - }; diff --git a/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt deleted file mode 100644 index 038c3a6a1f4d..000000000000 --- a/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt +++ /dev/null @@ -1,38 +0,0 @@ -Bindings for the Western Digital's MyBook Live memory-mapped GPIO controllers. - -The Western Digital MyBook Live has two memory-mapped GPIO controllers. -Both GPIO controller only have a single 8-bit data register, where GPIO -state can be read and/or written. - -Required properties: - - compatible: should be "wd,mbl-gpio" - - reg-names: must contain - "dat" - data register - - reg: address + size pairs describing the GPIO register sets; - order must correspond with the order of entries in reg-names - - #gpio-cells: must be set to 2. The first cell is the pin number and - the second cell is used to specify the gpio polarity: - 0 = active high - 1 = active low - - gpio-controller: Marks the device node as a gpio controller. - -Optional properties: - - no-output: GPIOs are read-only. - -Examples: - gpio0: gpio0@e0000000 { - compatible = "wd,mbl-gpio"; - reg-names = "dat"; - reg = <0xe0000000 0x1>; - #gpio-cells = <2>; - gpio-controller; - }; - - gpio1: gpio1@e0100000 { - compatible = "wd,mbl-gpio"; - reg-names = "dat"; - reg = <0xe0100000 0x1>; - #gpio-cells = <2>; - gpio-controller; - no-output; - }; diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml index 148f1da47603..9f9a14af875e 100644 --- a/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml +++ b/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml @@ -35,11 +35,11 @@ patternProperties: "^gpio@[0-9a-f]+$": # Child node type: object - $ref: "../gpio/brcm,bcm6345-gpio.yaml" + $ref: "../gpio/brcm,bcm63xx-gpio.yaml" description: GPIO controller for the SoC GPIOs. This child node definition should follow the bindings specified in - Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml. + Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml. "^pinctrl@[0-9a-f]+$": # Child node diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm63268-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm63268-gpio-sysctl.yaml index 7e582243ea76..803277dd2725 100644 --- a/Documentation/devicetree/bindings/mfd/brcm,bcm63268-gpio-sysctl.yaml +++ b/Documentation/devicetree/bindings/mfd/brcm,bcm63268-gpio-sysctl.yaml @@ -35,11 +35,11 @@ patternProperties: "^gpio@[0-9a-f]+$": # Child node type: object - $ref: "../gpio/brcm,bcm6345-gpio.yaml" + $ref: "../gpio/brcm,bcm63xx-gpio.yaml" description: GPIO controller for the SoC GPIOs. This child node definition should follow the bindings specified in - Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml. + Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml. "^pinctrl@[0-9a-f]+$": # Child node diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm6328-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm6328-gpio-sysctl.yaml index 2230848e11c3..b9a6856ce970 100644 --- a/Documentation/devicetree/bindings/mfd/brcm,bcm6328-gpio-sysctl.yaml +++ b/Documentation/devicetree/bindings/mfd/brcm,bcm6328-gpio-sysctl.yaml @@ -35,11 +35,11 @@ patternProperties: "^gpio@[0-9a-f]+$": # Child node type: object - $ref: "../gpio/brcm,bcm6345-gpio.yaml" + $ref: "../gpio/brcm,bcm63xx-gpio.yaml" description: GPIO controller for the SoC GPIOs. This child node definition should follow the bindings specified in - Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml. + Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml. "^pinctrl@[0-9a-f]+$": # Child node diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm6358-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm6358-gpio-sysctl.yaml index c06693b6f7aa..4651fe4dde07 100644 --- a/Documentation/devicetree/bindings/mfd/brcm,bcm6358-gpio-sysctl.yaml +++ b/Documentation/devicetree/bindings/mfd/brcm,bcm6358-gpio-sysctl.yaml @@ -35,11 +35,11 @@ patternProperties: "^gpio@[0-9a-f]+$": # Child node type: object - $ref: "../gpio/brcm,bcm6345-gpio.yaml" + $ref: "../gpio/brcm,bcm63xx-gpio.yaml" description: GPIO controller for the SoC GPIOs. This child node definition should follow the bindings specified in - Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml. + Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml. "^pinctrl@[0-9a-f]+$": # Child node diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm6362-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm6362-gpio-sysctl.yaml index c560bede0e37..0330b621fd38 100644 --- a/Documentation/devicetree/bindings/mfd/brcm,bcm6362-gpio-sysctl.yaml +++ b/Documentation/devicetree/bindings/mfd/brcm,bcm6362-gpio-sysctl.yaml @@ -35,11 +35,11 @@ patternProperties: "^gpio@[0-9a-f]+$": # Child node type: object - $ref: "../gpio/brcm,bcm6345-gpio.yaml" + $ref: "../gpio/brcm,bcm63xx-gpio.yaml" description: GPIO controller for the SoC GPIOs. This child node definition should follow the bindings specified in - Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml. + Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml. "^pinctrl@[0-9a-f]+$": # Child node diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm6368-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm6368-gpio-sysctl.yaml index c534f5f2404e..82d3e4415bda 100644 --- a/Documentation/devicetree/bindings/mfd/brcm,bcm6368-gpio-sysctl.yaml +++ b/Documentation/devicetree/bindings/mfd/brcm,bcm6368-gpio-sysctl.yaml @@ -35,11 +35,11 @@ patternProperties: "^gpio@[0-9a-f]+$": # Child node type: object - $ref: "../gpio/brcm,bcm6345-gpio.yaml" + $ref: "../gpio/brcm,bcm63xx-gpio.yaml" description: GPIO controller for the SoC GPIOs. This child node definition should follow the bindings specified in - Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml. + Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml. "^pinctrl@[0-9a-f]+$": # Child node