| Message ID | 1678164097-13247-10-git-send-email-quic_mmanikan@quicinc.com (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
| Series | Add multipd remoteproc support | expand |
On 3/7/2023 10:11 AM, Manikanta Mylavarapu wrote: > Enable nodes required for multipd remoteproc bring up > > Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com> > --- > arch/arm64/boot/dts/qcom/ipq5018.dtsi | 130 ++++++++++++++++++++++++++ > 1 file changed, 130 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi > index 084fb7b30dfd..4fa0990ab543 100644 > --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi > +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi > @@ -95,6 +95,24 @@ tz: tz@4ac00000 { > reg = <0x0 0x4ac00000 0x0 0x00400000>; > no-map; > }; > + > + q6_region: wcnss@4b000000 { > + no-map; > + reg = <0x0 0x4b000000 0x0 0x01700000>; move the no-map after reg property to keep it consistent with other nodes. Also no need to pad the size in reg property > + }; > + > + smem@4ab00000 { > + compatible = "qcom,smem"; > + reg = <0x0 0x4ab00000 0x0 0x00100000>; > + hwlocks = <&tcsr_mutex 0>; > + no-map; > + }; > + }; > + > + firmware { nodes should be in sorted order, please take care of this throughout the changes. > + scm { > + compatible = "qcom,scm-ipq5018", "qcom,scm"; > + }; > }; > > timer { > @@ -105,6 +123,30 @@ timer { > <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; > }; > > + wcss: wcss-smp2p { > + compatible = "qcom,smp2p"; > + qcom,smem = <435>, <428>; > + > + interrupt-parent = <&intc>; > + interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>; > + > + mboxes = <&apcs_glb 9>; > + > + qcom,local-pid = <0>; > + qcom,remote-pid = <1>; > + > + wcss_smp2p_out: master-kernel { > + qcom,entry-name = "master-kernel"; > + #qcom,smem-state-cells = <1>; > + }; > + > + wcss_smp2p_in: slave-kernel { > + qcom,entry-name = "slave-kernel"; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + }; > + > soc: soc@0 { > #address-cells = <1>; > #size-cells = <1>; > @@ -217,5 +259,93 @@ frame@b128000 { > status = "disabled"; > }; > }; > + > + tcsr_mutex: hwlock@1905000 { > + compatible = "qcom,tcsr-mutex"; > + reg = <0x01905000 0x8000>; Please cover the entire region of size 128KB > + #hwlock-cells = <1>; > + }; > + > + apcs_glb: mailbox@b111000 { > + compatible = "qcom,ipq5018-apcs-apps-global"; > + reg = <0x0b111000 0x1000>; > + #clock-cells = <1>; > + #mbox-cells = <1>; > + }; > + > + q6v5_wcss: remoteproc@cd00000 { > + compatible = "qcom,ipq5018-q6-mpd"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + reg = <0x0cd00000 0x4040>; reg can be moved after compatible > + interrupts-extended = <&intc GIC_SPI 291 IRQ_TYPE_EDGE_RISING>, > + <&wcss_smp2p_in 0 0>, > + <&wcss_smp2p_in 1 0>, > + <&wcss_smp2p_in 2 0>, > + <&wcss_smp2p_in 3 0>; > + interrupt-names = "wdog", > + "fatal", > + "ready", > + "handover", > + "stop-ack"; > + > + qcom,smem-states = <&wcss_smp2p_out 0>, > + <&wcss_smp2p_out 1>; > + qcom,smem-state-names = "shutdown", > + "stop"; > + memory-region = <&q6_region>; > + > + glink-edge { > + interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>; > + label = "rtr"; > + qcom,remote-pid = <1>; > + mboxes = <&apcs_glb 8>; > + }; > + > + q6_wcss_pd1: remoteproc_pd1 { > + compatible = "qcom,ipq5018-wcss-ahb-mpd"; > + }; > + > + q6_wcss_pd2: remoteproc_pd2 { > + compatible = "qcom,ipq5018-wcss-pcie-mpd"; > + interrupts-extended = <&wcss_smp2p_in 16 0>, > + <&wcss_smp2p_in 17 0>, Please take care of the alignment > + <&wcss_smp2p_in 20 0>, > + <&wcss_smp2p_in 19 0>; > + interrupt-names = "fatal", > + "ready", > + "spawn-ack", > + "stop-ack"; > + > + qcom,smem-states = <&wcss_smp2p_out 16>, > + <&wcss_smp2p_out 17>, > + <&wcss_smp2p_out 18>; > + qcom,smem-state-names = "shutdown", > + "stop", > + "spawn"; > + status = "disabled"; > + }; > + > + q6_wcss_pd3: remoteproc_pd3 { > + compatible = "qcom,ipq5018-wcss-pcie-mpd"; > + interrupts-extended = <&wcss_smp2p_in 24 0>, > + <&wcss_smp2p_in 25 0>, > + <&wcss_smp2p_in 28 0>, > + <&wcss_smp2p_in 27 0>; > + interrupt-names = "fatal", > + "ready", > + "spawn-ack", > + "stop-ack"; > + > + qcom,smem-states = <&wcss_smp2p_out 24>, > + <&wcss_smp2p_out 25>, > + <&wcss_smp2p_out 26>; > + qcom,smem-state-names = "shutdown", > + "stop", > + "spawn"; > + status = "disabled"; > + }; > + }; > }; > };
On 07/03/2023 05:41, Manikanta Mylavarapu wrote: > Enable nodes required for multipd remoteproc bring up > > Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com> > --- > arch/arm64/boot/dts/qcom/ipq5018.dtsi | 130 ++++++++++++++++++++++++++ > 1 file changed, 130 insertions(+) > soc: soc@0 { > #address-cells = <1>; > #size-cells = <1>; > @@ -217,5 +259,93 @@ frame@b128000 { > status = "disabled"; > }; > }; > + > + tcsr_mutex: hwlock@1905000 { This does not look like in correct order. Don't stuff things to the end of lists. > + compatible = "qcom,tcsr-mutex"; > + reg = <0x01905000 0x8000>; > + #hwlock-cells = <1>; > + }; > + > + apcs_glb: mailbox@b111000 { > + compatible = "qcom,ipq5018-apcs-apps-global"; > + reg = <0x0b111000 0x1000>; > + #clock-cells = <1>; > + #mbox-cells = <1>; > + }; > + > + q6v5_wcss: remoteproc@cd00000 { > + compatible = "qcom,ipq5018-q6-mpd"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + reg = <0x0cd00000 0x4040>; > + interrupts-extended = <&intc GIC_SPI 291 IRQ_TYPE_EDGE_RISING>, > + <&wcss_smp2p_in 0 0>, > + <&wcss_smp2p_in 1 0>, > + <&wcss_smp2p_in 2 0>, > + <&wcss_smp2p_in 3 0>; > + interrupt-names = "wdog", > + "fatal", > + "ready", > + "handover", > + "stop-ack"; > + > + qcom,smem-states = <&wcss_smp2p_out 0>, > + <&wcss_smp2p_out 1>; > + qcom,smem-state-names = "shutdown", > + "stop"; > + memory-region = <&q6_region>; > + > + glink-edge { > + interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>; > + label = "rtr"; > + qcom,remote-pid = <1>; > + mboxes = <&apcs_glb 8>; > + }; > + > + q6_wcss_pd1: remoteproc_pd1 { No underscores in node names, generic node names. Actually I don't get why do you need empty node at all. > + compatible = "qcom,ipq5018-wcss-ahb-mpd"; > + }; > + > + q6_wcss_pd2: remoteproc_pd2 { > + compatible = "qcom,ipq5018-wcss-pcie-mpd"; > + interrupts-extended = <&wcss_smp2p_in 16 0>, > + <&wcss_smp2p_in 17 0>, > + <&wcss_smp2p_in 20 0>, > + <&wcss_smp2p_in 19 0>; Best regards, Krzysztof
On 3/7/2023 7:52 PM, Kathiravan T wrote: > > On 3/7/2023 10:11 AM, Manikanta Mylavarapu wrote: >> Enable nodes required for multipd remoteproc bring up >> >> Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com> >> --- >> arch/arm64/boot/dts/qcom/ipq5018.dtsi | 130 ++++++++++++++++++++++++++ >> 1 file changed, 130 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi >> b/arch/arm64/boot/dts/qcom/ipq5018.dtsi >> index 084fb7b30dfd..4fa0990ab543 100644 >> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi >> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi >> @@ -95,6 +95,24 @@ tz: tz@4ac00000 { >> reg = <0x0 0x4ac00000 0x0 0x00400000>; >> no-map; >> }; >> + >> + q6_region: wcnss@4b000000 { >> + no-map; >> + reg = <0x0 0x4b000000 0x0 0x01700000>; > > > move the no-map after reg property to keep it consistent with other > nodes. Also no need to pad the size in reg property > > Sure. I will do it. >> + }; >> + >> + smem@4ab00000 { >> + compatible = "qcom,smem"; >> + reg = <0x0 0x4ab00000 0x0 0x00100000>; >> + hwlocks = <&tcsr_mutex 0>; >> + no-map; >> + }; >> + }; >> + >> + firmware { > > > nodes should be in sorted order, please take care of this throughout the > changes. > > Sure. I will do it. >> + scm { >> + compatible = "qcom,scm-ipq5018", "qcom,scm"; >> + }; >> }; >> timer { >> @@ -105,6 +123,30 @@ timer { >> <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | >> IRQ_TYPE_LEVEL_LOW)>; >> }; >> + wcss: wcss-smp2p { >> + compatible = "qcom,smp2p"; >> + qcom,smem = <435>, <428>; >> + >> + interrupt-parent = <&intc>; >> + interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>; >> + >> + mboxes = <&apcs_glb 9>; >> + >> + qcom,local-pid = <0>; >> + qcom,remote-pid = <1>; >> + >> + wcss_smp2p_out: master-kernel { >> + qcom,entry-name = "master-kernel"; >> + #qcom,smem-state-cells = <1>; >> + }; >> + >> + wcss_smp2p_in: slave-kernel { >> + qcom,entry-name = "slave-kernel"; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + }; >> + }; >> + >> soc: soc@0 { >> #address-cells = <1>; >> #size-cells = <1>; >> @@ -217,5 +259,93 @@ frame@b128000 { >> status = "disabled"; >> }; >> }; >> + >> + tcsr_mutex: hwlock@1905000 { >> + compatible = "qcom,tcsr-mutex"; >> + reg = <0x01905000 0x8000>; > > > Please cover the entire region of size 128KB > > Sure. I will do it. >> + #hwlock-cells = <1>; >> + }; >> + >> + apcs_glb: mailbox@b111000 { >> + compatible = "qcom,ipq5018-apcs-apps-global"; >> + reg = <0x0b111000 0x1000>; >> + #clock-cells = <1>; >> + #mbox-cells = <1>; >> + }; >> + >> + q6v5_wcss: remoteproc@cd00000 { >> + compatible = "qcom,ipq5018-q6-mpd"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + reg = <0x0cd00000 0x4040>; > > > reg can be moved after compatible > > Sure. I will do it. >> + interrupts-extended = <&intc GIC_SPI 291 >> IRQ_TYPE_EDGE_RISING>, >> + <&wcss_smp2p_in 0 0>, >> + <&wcss_smp2p_in 1 0>, >> + <&wcss_smp2p_in 2 0>, >> + <&wcss_smp2p_in 3 0>; >> + interrupt-names = "wdog", >> + "fatal", >> + "ready", >> + "handover", >> + "stop-ack"; >> + >> + qcom,smem-states = <&wcss_smp2p_out 0>, >> + <&wcss_smp2p_out 1>; >> + qcom,smem-state-names = "shutdown", >> + "stop"; >> + memory-region = <&q6_region>; >> + >> + glink-edge { >> + interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>; >> + label = "rtr"; >> + qcom,remote-pid = <1>; >> + mboxes = <&apcs_glb 8>; >> + }; >> + >> + q6_wcss_pd1: remoteproc_pd1 { >> + compatible = "qcom,ipq5018-wcss-ahb-mpd"; >> + }; >> + >> + q6_wcss_pd2: remoteproc_pd2 { >> + compatible = "qcom,ipq5018-wcss-pcie-mpd"; >> + interrupts-extended = <&wcss_smp2p_in 16 0>, >> + <&wcss_smp2p_in 17 0>, > > > Please take care of the alignment > > Sure. I will do it. Thanks & Regards, Manikanta. >> + <&wcss_smp2p_in 20 0>, >> + <&wcss_smp2p_in 19 0>; >> + interrupt-names = "fatal", >> + "ready", >> + "spawn-ack", >> + "stop-ack"; >> + >> + qcom,smem-states = <&wcss_smp2p_out 16>, >> + <&wcss_smp2p_out 17>, >> + <&wcss_smp2p_out 18>; >> + qcom,smem-state-names = "shutdown", >> + "stop", >> + "spawn"; >> + status = "disabled"; >> + }; >> + >> + q6_wcss_pd3: remoteproc_pd3 { >> + compatible = "qcom,ipq5018-wcss-pcie-mpd"; >> + interrupts-extended = <&wcss_smp2p_in 24 0>, >> + <&wcss_smp2p_in 25 0>, >> + <&wcss_smp2p_in 28 0>, >> + <&wcss_smp2p_in 27 0>; >> + interrupt-names = "fatal", >> + "ready", >> + "spawn-ack", >> + "stop-ack"; >> + >> + qcom,smem-states = <&wcss_smp2p_out 24>, >> + <&wcss_smp2p_out 25>, >> + <&wcss_smp2p_out 26>; >> + qcom,smem-state-names = "shutdown", >> + "stop", >> + "spawn"; >> + status = "disabled"; >> + }; >> + }; >> }; >> };
On 3/7/2023 9:11 PM, Krzysztof Kozlowski wrote: > On 07/03/2023 05:41, Manikanta Mylavarapu wrote: >> Enable nodes required for multipd remoteproc bring up >> >> Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com> >> --- >> arch/arm64/boot/dts/qcom/ipq5018.dtsi | 130 ++++++++++++++++++++++++++ >> 1 file changed, 130 insertions(+) >> soc: soc@0 { >> #address-cells = <1>; >> #size-cells = <1>; >> @@ -217,5 +259,93 @@ frame@b128000 { >> status = "disabled"; >> }; >> }; >> + >> + tcsr_mutex: hwlock@1905000 { > > This does not look like in correct order. Don't stuff things to the end > of lists. > Sure. I will keep nodes as per order. >> + compatible = "qcom,tcsr-mutex"; >> + reg = <0x01905000 0x8000>; >> + #hwlock-cells = <1>; >> + }; >> + >> + apcs_glb: mailbox@b111000 { >> + compatible = "qcom,ipq5018-apcs-apps-global"; >> + reg = <0x0b111000 0x1000>; >> + #clock-cells = <1>; >> + #mbox-cells = <1>; >> + }; >> + >> + q6v5_wcss: remoteproc@cd00000 { >> + compatible = "qcom,ipq5018-q6-mpd"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + reg = <0x0cd00000 0x4040>; >> + interrupts-extended = <&intc GIC_SPI 291 IRQ_TYPE_EDGE_RISING>, >> + <&wcss_smp2p_in 0 0>, >> + <&wcss_smp2p_in 1 0>, >> + <&wcss_smp2p_in 2 0>, >> + <&wcss_smp2p_in 3 0>; >> + interrupt-names = "wdog", >> + "fatal", >> + "ready", >> + "handover", >> + "stop-ack"; >> + >> + qcom,smem-states = <&wcss_smp2p_out 0>, >> + <&wcss_smp2p_out 1>; >> + qcom,smem-state-names = "shutdown", >> + "stop"; >> + memory-region = <&q6_region>; >> + >> + glink-edge { >> + interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>; >> + label = "rtr"; >> + qcom,remote-pid = <1>; >> + mboxes = <&apcs_glb 8>; >> + }; >> + >> + q6_wcss_pd1: remoteproc_pd1 { > > No underscores in node names, generic node names. Actually I don't get > why do you need empty node at all. > I removed underscores, now name should be pd-1/pd-2/pd-3. Yeah, it should not be empty node. I will correct it. Thanks & Regards, Manikanta. >> + compatible = "qcom,ipq5018-wcss-ahb-mpd"; >> + }; >> + >> + q6_wcss_pd2: remoteproc_pd2 { >> + compatible = "qcom,ipq5018-wcss-pcie-mpd"; >> + interrupts-extended = <&wcss_smp2p_in 16 0>, >> + <&wcss_smp2p_in 17 0>, >> + <&wcss_smp2p_in 20 0>, >> + <&wcss_smp2p_in 19 0>; > > > Best regards, > Krzysztof >
diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi index 084fb7b30dfd..4fa0990ab543 100644 --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi @@ -95,6 +95,24 @@ tz: tz@4ac00000 { reg = <0x0 0x4ac00000 0x0 0x00400000>; no-map; }; + + q6_region: wcnss@4b000000 { + no-map; + reg = <0x0 0x4b000000 0x0 0x01700000>; + }; + + smem@4ab00000 { + compatible = "qcom,smem"; + reg = <0x0 0x4ab00000 0x0 0x00100000>; + hwlocks = <&tcsr_mutex 0>; + no-map; + }; + }; + + firmware { + scm { + compatible = "qcom,scm-ipq5018", "qcom,scm"; + }; }; timer { @@ -105,6 +123,30 @@ timer { <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; }; + wcss: wcss-smp2p { + compatible = "qcom,smp2p"; + qcom,smem = <435>, <428>; + + interrupt-parent = <&intc>; + interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>; + + mboxes = <&apcs_glb 9>; + + qcom,local-pid = <0>; + qcom,remote-pid = <1>; + + wcss_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + wcss_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + soc: soc@0 { #address-cells = <1>; #size-cells = <1>; @@ -217,5 +259,93 @@ frame@b128000 { status = "disabled"; }; }; + + tcsr_mutex: hwlock@1905000 { + compatible = "qcom,tcsr-mutex"; + reg = <0x01905000 0x8000>; + #hwlock-cells = <1>; + }; + + apcs_glb: mailbox@b111000 { + compatible = "qcom,ipq5018-apcs-apps-global"; + reg = <0x0b111000 0x1000>; + #clock-cells = <1>; + #mbox-cells = <1>; + }; + + q6v5_wcss: remoteproc@cd00000 { + compatible = "qcom,ipq5018-q6-mpd"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + reg = <0x0cd00000 0x4040>; + interrupts-extended = <&intc GIC_SPI 291 IRQ_TYPE_EDGE_RISING>, + <&wcss_smp2p_in 0 0>, + <&wcss_smp2p_in 1 0>, + <&wcss_smp2p_in 2 0>, + <&wcss_smp2p_in 3 0>; + interrupt-names = "wdog", + "fatal", + "ready", + "handover", + "stop-ack"; + + qcom,smem-states = <&wcss_smp2p_out 0>, + <&wcss_smp2p_out 1>; + qcom,smem-state-names = "shutdown", + "stop"; + memory-region = <&q6_region>; + + glink-edge { + interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>; + label = "rtr"; + qcom,remote-pid = <1>; + mboxes = <&apcs_glb 8>; + }; + + q6_wcss_pd1: remoteproc_pd1 { + compatible = "qcom,ipq5018-wcss-ahb-mpd"; + }; + + q6_wcss_pd2: remoteproc_pd2 { + compatible = "qcom,ipq5018-wcss-pcie-mpd"; + interrupts-extended = <&wcss_smp2p_in 16 0>, + <&wcss_smp2p_in 17 0>, + <&wcss_smp2p_in 20 0>, + <&wcss_smp2p_in 19 0>; + interrupt-names = "fatal", + "ready", + "spawn-ack", + "stop-ack"; + + qcom,smem-states = <&wcss_smp2p_out 16>, + <&wcss_smp2p_out 17>, + <&wcss_smp2p_out 18>; + qcom,smem-state-names = "shutdown", + "stop", + "spawn"; + status = "disabled"; + }; + + q6_wcss_pd3: remoteproc_pd3 { + compatible = "qcom,ipq5018-wcss-pcie-mpd"; + interrupts-extended = <&wcss_smp2p_in 24 0>, + <&wcss_smp2p_in 25 0>, + <&wcss_smp2p_in 28 0>, + <&wcss_smp2p_in 27 0>; + interrupt-names = "fatal", + "ready", + "spawn-ack", + "stop-ack"; + + qcom,smem-states = <&wcss_smp2p_out 24>, + <&wcss_smp2p_out 25>, + <&wcss_smp2p_out 26>; + qcom,smem-state-names = "shutdown", + "stop", + "spawn"; + status = "disabled"; + }; + }; }; };
Enable nodes required for multipd remoteproc bring up Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com> --- arch/arm64/boot/dts/qcom/ipq5018.dtsi | 130 ++++++++++++++++++++++++++ 1 file changed, 130 insertions(+)