@@ -125,12 +125,22 @@ reg_usb2_vbus: regulator-usb2 {
regulator-max-microvolt = <5000000>;
};
+ reg_can1_stby: regulator-can1-stby {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_can1>;
+ regulator-name = "can1_stby";
+ gpio = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
reg_can2_stby: regulator-can2-stby {
compatible = "regulator-fixed";
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reg_can>;
+ pinctrl-0 = <&pinctrl_reg_can2>;
regulator-name = "can2_stby";
- gpio = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ gpio = <&gpio5 5 GPIO_ACTIVE_LOW>;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
@@ -164,6 +174,21 @@ &A53_3 {
cpu-supply = <®_arm>;
};
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1>;
+ cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ tpm@0 {
+ compatible = "tcg,tpm_tis-spi";
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ reg = <0x0>;
+ spi-max-frequency = <36000000>;
+ };
+};
+
/* off-board header */
&ecspi2 {
pinctrl-names = "default";
@@ -204,6 +229,13 @@ fixed-link {
};
};
+&flexcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_can1_stby>;
+ status = "okay";
+};
+
&flexcan2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flexcan2>;
@@ -214,38 +246,38 @@ &flexcan2 {
&gpio1 {
gpio-line-names =
"", "", "", "", "", "", "", "",
- "", "", "dio0", "", "dio1", "", "", "",
+ "", "dio0", "", "dio1", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "";
};
&gpio2 {
gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "pcie3_wdis#", "",
+ "", "", "", "", "", "", "m2_pin20", "",
+ "", "", "", "", "", "pcie1_wdis#", "pcie3_wdis#", "",
"", "", "pcie2_wdis#", "", "", "", "", "",
"", "", "", "", "", "", "", "";
};
&gpio3 {
gpio-line-names =
- "m2_gdis#", "", "", "", "", "", "", "m2_rst#",
+ "", "", "", "", "", "", "m2_rst", "",
+ "", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
- "m2_off#", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "";
};
&gpio4 {
gpio-line-names =
+ "", "", "m2_off#", "", "", "", "", "",
"", "", "", "", "", "", "", "",
- "", "", "", "", "", "", "", "",
- "", "", "", "", "m2_wdis#", "", "", "",
- "", "", "", "", "", "", "", "uart_rs485";
+ "", "", "m2_wdis#", "", "", "", "", "",
+ "", "", "", "", "", "", "", "rs485_en";
};
&gpio5 {
gpio-line-names =
- "uart_half", "uart_term", "", "", "", "", "", "",
+ "rs485_hd", "rs485_term", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "";
@@ -286,6 +318,12 @@ channel@8 {
label = "vdd_bat";
};
+ channel@16 {
+ gw,mode = <4>;
+ reg = <0x16>;
+ label = "fan_tach";
+ };
+
channel@82 {
gw,mode = <2>;
reg = <0x82>;
@@ -358,6 +396,11 @@ channel@a2 {
gw,voltage-divider-ohms = <10000 10000>;
};
};
+
+ fan-controller@a {
+ compatible = "gw,gsc-fan";
+ reg = <0x0a>;
+ };
};
gpio: gpio@23 {
@@ -369,85 +412,6 @@ gpio: gpio@23 {
interrupts = <4>;
};
- pmic@25 {
- compatible = "nxp,pca9450c";
- reg = <0x25>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pmic>;
- interrupt-parent = <&gpio3>;
- interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
-
- regulators {
- BUCK1 {
- regulator-name = "BUCK1";
- regulator-min-microvolt = <720000>;
- regulator-max-microvolt = <1000000>;
- regulator-boot-on;
- regulator-always-on;
- regulator-ramp-delay = <3125>;
- };
-
- reg_arm: BUCK2 {
- regulator-name = "BUCK2";
- regulator-min-microvolt = <720000>;
- regulator-max-microvolt = <1025000>;
- regulator-boot-on;
- regulator-always-on;
- regulator-ramp-delay = <3125>;
- nxp,dvs-run-voltage = <950000>;
- nxp,dvs-standby-voltage = <850000>;
- };
-
- BUCK4 {
- regulator-name = "BUCK4";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3600000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- BUCK5 {
- regulator-name = "BUCK5";
- regulator-min-microvolt = <1650000>;
- regulator-max-microvolt = <1950000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- BUCK6 {
- regulator-name = "BUCK6";
- regulator-min-microvolt = <1045000>;
- regulator-max-microvolt = <1155000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- LDO1 {
- regulator-name = "LDO1";
- regulator-min-microvolt = <1650000>;
- regulator-max-microvolt = <1950000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- LDO3 {
- regulator-name = "LDO3";
- regulator-min-microvolt = <1710000>;
- regulator-max-microvolt = <1890000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- LDO5 {
- regulator-name = "LDO5";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
- };
- };
-
eeprom@50 {
compatible = "atmel,24c02";
reg = <0x50>;
@@ -559,7 +523,6 @@ fixed-link {
};
};
-/* off-board header */
&i2c3 {
clock-frequency = <400000>;
pinctrl-names = "default", "gpio";
@@ -568,6 +531,85 @@ &i2c3 {
scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
+
+ pmic@25 {
+ compatible = "nxp,pca9450c";
+ reg = <0x25>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <720000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ reg_arm: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <720000>;
+ regulator-max-microvolt = <1025000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ nxp,dvs-run-voltage = <950000>;
+ nxp,dvs-standby-voltage = <850000>;
+ };
+
+ BUCK4 {
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ BUCK5 {
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ BUCK6 {
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <1045000>;
+ regulator-max-microvolt = <1155000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <1710000>;
+ regulator-max-microvolt = <1890000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ LDO5 {
+ regulator-name = "LDO5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
/* off-board header */
@@ -726,12 +768,14 @@ pinctrl_hog: hoggrp {
fsl,pins = <
MX8MP_IOMUXC_GPIO1_IO09__GPIO1_IO09 0x40000040 /* DIO0 */
MX8MP_IOMUXC_GPIO1_IO11__GPIO1_IO11 0x40000040 /* DIO1 */
- MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14 0x40000040 /* M2SKT_OFF# */
- MX8MP_IOMUXC_SD2_DATA3__GPIO2_IO18 0x40000150 /* PCIE2_WDIS# */
+ MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02 0x40000040 /* M2SKT_OFF# */
+ MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x40000150 /* M2SKT_WDIS# */
+ MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06 0x40000040 /* M2SKT_PIN20 */
+ MX8MP_IOMUXC_SD1_STROBE__GPIO2_IO11 0x40000040 /* M2SKT_PIN22 */
+ MX8MP_IOMUXC_SD2_CLK__GPIO2_IO13 0x40000150 /* PCIE1_WDIS# */
MX8MP_IOMUXC_SD2_CMD__GPIO2_IO14 0x40000150 /* PCIE3_WDIS# */
+ MX8MP_IOMUXC_SD2_DATA3__GPIO2_IO18 0x40000150 /* PCIE2_WDIS# */
MX8MP_IOMUXC_NAND_DATA00__GPIO3_IO06 0x40000040 /* M2SKT_RST# */
- MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x40000150 /* M2SKT_WDIS# */
- MX8MP_IOMUXC_NAND_ALE__GPIO3_IO00 0x40000150 /* M2SKT_GDIS# */
MX8MP_IOMUXC_SAI3_TXD__GPIO5_IO01 0x40000104 /* UART_TERM */
MX8MP_IOMUXC_SAI3_TXFS__GPIO4_IO31 0x40000104 /* UART_RS485 */
MX8MP_IOMUXC_SAI3_TXC__GPIO5_IO00 0x40000104 /* UART_HALF */
@@ -784,6 +828,13 @@ MX8MP_IOMUXC_SAI1_RXC__ENET1_1588_EVENT0_OUT 0x140
>;
};
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SPDIF_RX__CAN1_RX 0x154
+ MX8MP_IOMUXC_SPDIF_TX__CAN1_TX 0x154
+ >;
+ };
+
pinctrl_flexcan2: flexcan2grp {
fsl,pins = <
MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX 0x154
@@ -869,7 +920,7 @@ MX8MP_IOMUXC_SD2_DATA1__GPIO2_IO16 0x10
pinctrl_pcie0: pciegrp {
fsl,pins = <
- MX8MP_IOMUXC_SD2_DATA2__GPIO2_IO17 0x110
+ MX8MP_IOMUXC_SD2_DATA2__GPIO2_IO17 0x106
>;
};
@@ -885,12 +936,18 @@ MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12 0x140
>;
};
- pinctrl_reg_can: regcangrp {
+ pinctrl_reg_can1: regcan1grp {
fsl,pins = <
MX8MP_IOMUXC_SAI5_RXFS__GPIO3_IO19 0x154
>;
};
+ pinctrl_reg_can2: regcan2grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SPDIF_EXT_CLK__GPIO5_IO05 0x154
+ >;
+ };
+
pinctrl_reg_usb2: regusb2grp {
fsl,pins = <
MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06 0x140
@@ -903,12 +960,12 @@ MX8MP_IOMUXC_NAND_DATA03__GPIO3_IO09 0x110
>;
};
- pinctrl_sai2: sai2grp {
+ pinctrl_spi1: spi1grp {
fsl,pins = <
- MX8MP_IOMUXC_SAI2_TXFS__AUDIOMIX_SAI2_TX_SYNC 0xd6
- MX8MP_IOMUXC_SAI2_TXD0__AUDIOMIX_SAI2_TX_DATA00 0xd6
- MX8MP_IOMUXC_SAI2_TXC__AUDIOMIX_SAI2_TX_BCLK 0xd6
- MX8MP_IOMUXC_SAI2_MCLK__AUDIOMIX_SAI2_MCLK 0xd6
+ MX8MP_IOMUXC_ECSPI1_SCLK__ECSPI1_SCLK 0x82
+ MX8MP_IOMUXC_ECSPI1_MOSI__ECSPI1_MOSI 0x82
+ MX8MP_IOMUXC_ECSPI1_MISO__ECSPI1_MISO 0x82
+ MX8MP_IOMUXC_ECSPI1_SS0__GPIO5_IO09 0x140
>;
};
Update the imx8mp-venice-gw74xx for revB: - add CAN1 - add TIS-TPM on SPI2 - add FAN controller - fix PMIC I2C bus (revA PMIC I2C was non-functional so no need for backward compatible option) - M2 socket GPIO's moved Signed-off-by: Tim Harvey <tharvey@gateworks.com> --- v2: - fix fan-controller unit-address --- .../dts/freescale/imx8mp-venice-gw74xx.dts | 261 +++++++++++------- 1 file changed, 159 insertions(+), 102 deletions(-)