diff mbox series

[v3,11/29] media: ov2680: Check for "powerdown" GPIO con-id before checking for "reset" GPIO con-id

Message ID 20230627131830.54601-12-hdegoede@redhat.com (mailing list archive)
State New, archived
Headers show
Series media: ov2680: Bugfixes + ACPI + selection(crop-tgt) API support | expand

Commit Message

Hans de Goede June 27, 2023, 1:18 p.m. UTC
The datasheet of the OV2680 labels the single GPIO to put the sensor in
powersaving mode as XSHUTDN aka shutdown, _not_ reset.

This is important because some boards have standardized sensor connectors
which allow connecting various sensor modules. These connectors have both
reset and powerdown signals and the powerdown signal is routed to
the OV2680's XSHUTDN pin.

On x86/ACPI multiple Bay Trail, Cherry Trail, Sky Lake and Kaby Lake models
have an OV2680 connected to the ISP2 / IPU3. On these devices the GPIOS are
not described in DT instead the GPIOs are described with an Intel specific
DSM which labels them as either powerdown or reset. Often this DSM returns
both reset and powerdown pins even though the OV2680 has only 1 such pin.

For the ov2680 driver to work on these devices it must use the GPIO with
"powerdown" as con-id, matching the XSHUTDN name from the datasheet.

As for why "powerdown" vs say "shutdown" the ACPI DSM -> con-id mapping
code is shared, so we must use standardized names and currently all of
the following sensor drivers already use "powerdown":
adv7180, gc0310, isl7998x, ov02a10, ov2659, ov5640, ov5648, ov5670,
ov5693, ov7670, ov772x, ov7740, ov8858, ov8865 and ov9650 .

Where as the hi846 driver is the lonely standout using "shutdown".

Try the "powerdown" con-id first to make things work, falling back to
"reset" to keep existing DT setups working.

Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 drivers/media/i2c/ov2680.c | 29 ++++++++++++++++++++---------
 1 file changed, 20 insertions(+), 9 deletions(-)

Comments

Daniel Scally June 27, 2023, 2:40 p.m. UTC | #1
Hi Hans

On 27/06/2023 15:18, Hans de Goede wrote:
> The datasheet of the OV2680 labels the single GPIO to put the sensor in
> powersaving mode as XSHUTDN aka shutdown, _not_ reset.
>
> This is important because some boards have standardized sensor connectors
> which allow connecting various sensor modules. These connectors have both
> reset and powerdown signals and the powerdown signal is routed to
> the OV2680's XSHUTDN pin.
>
> On x86/ACPI multiple Bay Trail, Cherry Trail, Sky Lake and Kaby Lake models
> have an OV2680 connected to the ISP2 / IPU3. On these devices the GPIOS are
> not described in DT instead the GPIOs are described with an Intel specific
> DSM which labels them as either powerdown or reset. Often this DSM returns
> both reset and powerdown pins even though the OV2680 has only 1 such pin.
>
> For the ov2680 driver to work on these devices it must use the GPIO with
> "powerdown" as con-id, matching the XSHUTDN name from the datasheet.
>
> As for why "powerdown" vs say "shutdown" the ACPI DSM -> con-id mapping
> code is shared, so we must use standardized names and currently all of
> the following sensor drivers already use "powerdown":
> adv7180, gc0310, isl7998x, ov02a10, ov2659, ov5640, ov5648, ov5670,
> ov5693, ov7670, ov772x, ov7740, ov8858, ov8865 and ov9650 .
>
> Where as the hi846 driver is the lonely standout using "shutdown".
>
> Try the "powerdown" con-id first to make things work, falling back to
> "reset" to keep existing DT setups working.
>
> Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---


Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>

>   drivers/media/i2c/ov2680.c | 29 ++++++++++++++++++++---------
>   1 file changed, 20 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/media/i2c/ov2680.c b/drivers/media/i2c/ov2680.c
> index 824e2962e7d5..0de047c49c31 100644
> --- a/drivers/media/i2c/ov2680.c
> +++ b/drivers/media/i2c/ov2680.c
> @@ -96,7 +96,7 @@ struct ov2680_dev {
>   	u32				xvclk_freq;
>   	struct regulator_bulk_data	supplies[OV2680_NUM_SUPPLIES];
>   
> -	struct gpio_desc		*reset_gpio;
> +	struct gpio_desc		*pwdn_gpio;
>   	struct mutex			lock; /* protect members */
>   
>   	bool				mode_pending_changes;
> @@ -180,19 +180,19 @@ static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl)
>   
>   static void ov2680_power_up(struct ov2680_dev *sensor)
>   {
> -	if (!sensor->reset_gpio)
> +	if (!sensor->pwdn_gpio)
>   		return;
>   
> -	gpiod_set_value(sensor->reset_gpio, 0);
> +	gpiod_set_value(sensor->pwdn_gpio, 0);
>   	usleep_range(5000, 10000);
>   }
>   
>   static void ov2680_power_down(struct ov2680_dev *sensor)
>   {
> -	if (!sensor->reset_gpio)
> +	if (!sensor->pwdn_gpio)
>   		return;
>   
> -	gpiod_set_value(sensor->reset_gpio, 1);
> +	gpiod_set_value(sensor->pwdn_gpio, 1);
>   	usleep_range(5000, 10000);
>   }
>   
> @@ -350,7 +350,7 @@ static int ov2680_power_on(struct ov2680_dev *sensor)
>   		return ret;
>   	}
>   
> -	if (!sensor->reset_gpio) {
> +	if (!sensor->pwdn_gpio) {
>   		ret = cci_write(sensor->regmap, OV2680_REG_SOFT_RESET, 0x01,
>   				NULL);
>   		if (ret != 0) {
> @@ -742,16 +742,27 @@ static int ov2680_check_id(struct ov2680_dev *sensor)
>   static int ov2680_parse_dt(struct ov2680_dev *sensor)
>   {
>   	struct device *dev = sensor->dev;
> +	struct gpio_desc *gpio;
>   	int ret;
>   
> -	sensor->reset_gpio = devm_gpiod_get_optional(dev, "reset",
> -						     GPIOD_OUT_HIGH);
> -	ret = PTR_ERR_OR_ZERO(sensor->reset_gpio);
> +	/*
> +	 * The pin we want is named XSHUTDN in the datasheet. Linux sensor
> +	 * drivers have standardized on using "powerdown" as con-id name
> +	 * for powerdown or shutdown pins. Older DTB files use "reset",
> +	 * so fallback to that if there is no "powerdown" pin.
> +	 */
> +	gpio = devm_gpiod_get_optional(dev, "powerdown", GPIOD_OUT_HIGH);
> +	if (!gpio)
> +		gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
> +
> +	ret = PTR_ERR_OR_ZERO(gpio);
>   	if (ret < 0) {
>   		dev_dbg(dev, "error while getting reset gpio: %d\n", ret);
>   		return ret;
>   	}
>   
> +	sensor->pwdn_gpio = gpio;
> +
>   	sensor->xvclk = devm_clk_get(dev, "xvclk");
>   	if (IS_ERR(sensor->xvclk)) {
>   		dev_err(dev, "xvclk clock missing or invalid\n");
diff mbox series

Patch

diff --git a/drivers/media/i2c/ov2680.c b/drivers/media/i2c/ov2680.c
index 824e2962e7d5..0de047c49c31 100644
--- a/drivers/media/i2c/ov2680.c
+++ b/drivers/media/i2c/ov2680.c
@@ -96,7 +96,7 @@  struct ov2680_dev {
 	u32				xvclk_freq;
 	struct regulator_bulk_data	supplies[OV2680_NUM_SUPPLIES];
 
-	struct gpio_desc		*reset_gpio;
+	struct gpio_desc		*pwdn_gpio;
 	struct mutex			lock; /* protect members */
 
 	bool				mode_pending_changes;
@@ -180,19 +180,19 @@  static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl)
 
 static void ov2680_power_up(struct ov2680_dev *sensor)
 {
-	if (!sensor->reset_gpio)
+	if (!sensor->pwdn_gpio)
 		return;
 
-	gpiod_set_value(sensor->reset_gpio, 0);
+	gpiod_set_value(sensor->pwdn_gpio, 0);
 	usleep_range(5000, 10000);
 }
 
 static void ov2680_power_down(struct ov2680_dev *sensor)
 {
-	if (!sensor->reset_gpio)
+	if (!sensor->pwdn_gpio)
 		return;
 
-	gpiod_set_value(sensor->reset_gpio, 1);
+	gpiod_set_value(sensor->pwdn_gpio, 1);
 	usleep_range(5000, 10000);
 }
 
@@ -350,7 +350,7 @@  static int ov2680_power_on(struct ov2680_dev *sensor)
 		return ret;
 	}
 
-	if (!sensor->reset_gpio) {
+	if (!sensor->pwdn_gpio) {
 		ret = cci_write(sensor->regmap, OV2680_REG_SOFT_RESET, 0x01,
 				NULL);
 		if (ret != 0) {
@@ -742,16 +742,27 @@  static int ov2680_check_id(struct ov2680_dev *sensor)
 static int ov2680_parse_dt(struct ov2680_dev *sensor)
 {
 	struct device *dev = sensor->dev;
+	struct gpio_desc *gpio;
 	int ret;
 
-	sensor->reset_gpio = devm_gpiod_get_optional(dev, "reset",
-						     GPIOD_OUT_HIGH);
-	ret = PTR_ERR_OR_ZERO(sensor->reset_gpio);
+	/*
+	 * The pin we want is named XSHUTDN in the datasheet. Linux sensor
+	 * drivers have standardized on using "powerdown" as con-id name
+	 * for powerdown or shutdown pins. Older DTB files use "reset",
+	 * so fallback to that if there is no "powerdown" pin.
+	 */
+	gpio = devm_gpiod_get_optional(dev, "powerdown", GPIOD_OUT_HIGH);
+	if (!gpio)
+		gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+
+	ret = PTR_ERR_OR_ZERO(gpio);
 	if (ret < 0) {
 		dev_dbg(dev, "error while getting reset gpio: %d\n", ret);
 		return ret;
 	}
 
+	sensor->pwdn_gpio = gpio;
+
 	sensor->xvclk = devm_clk_get(dev, "xvclk");
 	if (IS_ERR(sensor->xvclk)) {
 		dev_err(dev, "xvclk clock missing or invalid\n");