| Message ID | 20230713171851.73052-4-sebastian.reichel@collabora.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | RK3588 PCIe2 support | expand |
On Thu, 13 Jul 2023 at 22:49, Sebastian Reichel <sebastian.reichel@collabora.com> wrote: > > Add all three PCIe2 IP blocks to the RK3588 DT. Note, that RK3588 > also has two PCIe3 IP blocks, that will be handled separately. > > Co-developed-by: Kever Yang <kever.yang@rock-chips.com> > Signed-off-by: Kever Yang <kever.yang@rock-chips.com> > Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> > --- Tested all pcie2x1l0 and pcie2x1l1 IP blocks in edgeble-neu6a, 6b. Tested-by: Jagan Teki <jagan@edgeble.ai> # edgeble-neu6a, 6b Reviewed-by: Jagan Teki <jagan@edgeble.ai>
On Thu, Jul 13, 2023 at 07:18:51PM +0200, Sebastian Reichel wrote: > Add all three PCIe2 IP blocks to the RK3588 DT. Note, that RK3588 > also has two PCIe3 IP blocks, that will be handled separately. > > Co-developed-by: Kever Yang <kever.yang@rock-chips.com> > Signed-off-by: Kever Yang <kever.yang@rock-chips.com> > Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> > --- > arch/arm64/boot/dts/rockchip/rk3588.dtsi | 54 +++++++++++ > arch/arm64/boot/dts/rockchip/rk3588s.dtsi | 108 ++++++++++++++++++++++ > 2 files changed, 162 insertions(+) > > diff --git a/arch/arm64/boot/dts/rockchip/rk3588.dtsi b/arch/arm64/boot/dts/rockchip/rk3588.dtsi > index 6be9bf81c09c..4d66ca6c2e4c 100644 > --- a/arch/arm64/boot/dts/rockchip/rk3588.dtsi > +++ b/arch/arm64/boot/dts/rockchip/rk3588.dtsi > @@ -80,6 +80,60 @@ i2s10_8ch: i2s@fde00000 { > status = "disabled"; > }; > > + pcie2x1l0: pcie@fe170000 { > + compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie"; > + #address-cells = <3>; > + #size-cells = <2>; > + bus-range = <0x20 0x2f>; > + clocks = <&cru ACLK_PCIE_1L0_MSTR>, <&cru ACLK_PCIE_1L0_SLV>, > + <&cru ACLK_PCIE_1L0_DBI>, <&cru PCLK_PCIE_1L0>, > + <&cru CLK_PCIE_AUX2>, <&cru CLK_PCIE1L0_PIPE>; > + clock-names = "aclk_mst", "aclk_slv", > + "aclk_dbi", "pclk", > + "aux", "pipe"; > + device_type = "pci"; > + interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH 0>; > + interrupt-names = "sys", "pmc", "msg", "legacy", "err"; > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 7>; > + interrupt-map = <0 0 0 1 &pcie2x1l0_intc 0>, > + <0 0 0 2 &pcie2x1l0_intc 1>, > + <0 0 0 3 &pcie2x1l0_intc 2>, > + <0 0 0 4 &pcie2x1l0_intc 3>; > + linux,pci-domain = <2>; > + num-ib-windows = <8>; > + num-ob-windows = <8>; > + num-viewport = <4>; These properties are marked as deprecated and unused by the driver anyway. You can freely drop them. > + max-link-speed = <2>; > + msi-map = <0x2000 &its0 0x2000 0x1000>; > + num-lanes = <1>; > + phys = <&combphy1_ps PHY_TYPE_PCIE>; > + phy-names = "pcie-phy"; > + power-domains = <&power RK3588_PD_PCIE>; > + ranges = <0x01000000 0x0 0xf2100000 0x0 0xf2100000 0x0 0x00100000>, > + <0x02000000 0x0 0xf2200000 0x0 0xf2200000 0x0 0x00e00000>, > + <0x03000000 0x0 0x40000000 0x9 0x80000000 0x0 0x40000000>; > + reg = <0xa 0x40800000 0x0 0x00400000>, > + <0x0 0xfe170000 0x0 0x00010000>, > + <0x0 0xf2000000 0x0 0x00100000>; > + reg-names = "dbi", "apb", "config"; > + resets = <&cru SRST_PCIE2_POWER_UP>, <&cru SRST_P_PCIE2>; > + reset-names = "pwr", "pipe"; > + status = "disabled"; > + > + pcie2x1l0_intc: legacy-interrupt-controller { > + interrupt-controller; > + #address-cells = <0>; > + #interrupt-cells = <1>; > + interrupt-parent = <&gic>; > + interrupts = <GIC_SPI 240 IRQ_TYPE_EDGE_RISING 0>; > + }; > + }; > + > gmac0: ethernet@fe1b0000 { > compatible = "rockchip,rk3588-gmac", "snps,dwmac-4.20a"; > reg = <0x0 0xfe1b0000 0x0 0x10000>; > diff --git a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi > index c9f9dd2472f5..27d711d114d6 100644 > --- a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi > +++ b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi > @@ -1227,6 +1227,114 @@ qos_vop_m1: qos@fdf82200 { > reg = <0x0 0xfdf82200 0x0 0x20>; > }; > > + pcie2x1l1: pcie@fe180000 { > + compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie"; > + #address-cells = <3>; > + #size-cells = <2>; > + bus-range = <0x30 0x3f>; > + clocks = <&cru ACLK_PCIE_1L1_MSTR>, <&cru ACLK_PCIE_1L1_SLV>, > + <&cru ACLK_PCIE_1L1_DBI>, <&cru PCLK_PCIE_1L1>, > + <&cru CLK_PCIE_AUX3>, <&cru CLK_PCIE1L1_PIPE>; > + clock-names = "aclk_mst", "aclk_slv", > + "aclk_dbi", "pclk", > + "aux", "pipe"; > + device_type = "pci"; > + interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH 0>; > + interrupt-names = "sys", "pmc", "msg", "legacy", "err"; > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 7>; > + interrupt-map = <0 0 0 1 &pcie2x1l1_intc 0>, > + <0 0 0 2 &pcie2x1l1_intc 1>, > + <0 0 0 3 &pcie2x1l1_intc 2>, > + <0 0 0 4 &pcie2x1l1_intc 3>; > + linux,pci-domain = <3>; > + num-ib-windows = <8>; > + num-ob-windows = <8>; > + num-viewport = <4>; ditto > + max-link-speed = <2>; > + msi-map = <0x3000 &its0 0x3000 0x1000>; > + num-lanes = <1>; > + phys = <&combphy2_psu PHY_TYPE_PCIE>; > + phy-names = "pcie-phy"; > + power-domains = <&power RK3588_PD_PCIE>; > + ranges = <0x01000000 0x0 0xf3100000 0x0 0xf3100000 0x0 0x00100000>, > + <0x02000000 0x0 0xf3200000 0x0 0xf3200000 0x0 0x00e00000>, > + <0x03000000 0x0 0x40000000 0x9 0xc0000000 0x0 0x40000000>; > + reg = <0xa 0x40c00000 0x0 0x00400000>, > + <0x0 0xfe180000 0x0 0x00010000>, > + <0x0 0xf3000000 0x0 0x00100000>; > + reg-names = "dbi", "apb", "config"; > + resets = <&cru SRST_PCIE3_POWER_UP>, <&cru SRST_P_PCIE3>; > + reset-names = "pwr", "pipe"; > + status = "disabled"; > + > + pcie2x1l1_intc: legacy-interrupt-controller { > + interrupt-controller; > + #address-cells = <0>; > + #interrupt-cells = <1>; > + interrupt-parent = <&gic>; > + interrupts = <GIC_SPI 245 IRQ_TYPE_EDGE_RISING 0>; > + }; > + }; > + > + pcie2x1l2: pcie@fe190000 { > + compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie"; > + #address-cells = <3>; > + #size-cells = <2>; > + bus-range = <0x40 0x4f>; > + clocks = <&cru ACLK_PCIE_1L2_MSTR>, <&cru ACLK_PCIE_1L2_SLV>, > + <&cru ACLK_PCIE_1L2_DBI>, <&cru PCLK_PCIE_1L2>, > + <&cru CLK_PCIE_AUX4>, <&cru CLK_PCIE1L2_PIPE>; > + clock-names = "aclk_mst", "aclk_slv", > + "aclk_dbi", "pclk", > + "aux", "pipe"; > + device_type = "pci"; > + interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH 0>; > + interrupt-names = "sys", "pmc", "msg", "legacy", "err"; > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 7>; > + interrupt-map = <0 0 0 1 &pcie2x1l2_intc 0>, > + <0 0 0 2 &pcie2x1l2_intc 1>, > + <0 0 0 3 &pcie2x1l2_intc 2>, > + <0 0 0 4 &pcie2x1l2_intc 3>; > + linux,pci-domain = <4>; > + num-ib-windows = <8>; > + num-ob-windows = <8>; > + num-viewport = <4>; ditto -Serge(y) > + max-link-speed = <2>; > + msi-map = <0x4000 &its0 0x4000 0x1000>; > + num-lanes = <1>; > + phys = <&combphy0_ps PHY_TYPE_PCIE>; > + phy-names = "pcie-phy"; > + power-domains = <&power RK3588_PD_PCIE>; > + ranges = <0x01000000 0x0 0xf4100000 0x0 0xf4100000 0x0 0x00100000>, > + <0x02000000 0x0 0xf4200000 0x0 0xf4200000 0x0 0x00e00000>, > + <0x03000000 0x0 0x40000000 0xa 0x00000000 0x0 0x40000000>; > + reg = <0xa 0x41000000 0x0 0x00400000>, > + <0x0 0xfe190000 0x0 0x00010000>, > + <0x0 0xf4000000 0x0 0x00100000>; > + reg-names = "dbi", "apb", "config"; > + resets = <&cru SRST_PCIE4_POWER_UP>, <&cru SRST_P_PCIE4>; > + reset-names = "pwr", "pipe"; > + status = "disabled"; > + > + pcie2x1l2_intc: legacy-interrupt-controller { > + interrupt-controller; > + #address-cells = <0>; > + #interrupt-cells = <1>; > + interrupt-parent = <&gic>; > + interrupts = <GIC_SPI 250 IRQ_TYPE_EDGE_RISING 0>; > + }; > + }; > + > gmac1: ethernet@fe1c0000 { > compatible = "rockchip,rk3588-gmac", "snps,dwmac-4.20a"; > reg = <0x0 0xfe1c0000 0x0 0x10000>; > -- > 2.40.1 >
diff --git a/arch/arm64/boot/dts/rockchip/rk3588.dtsi b/arch/arm64/boot/dts/rockchip/rk3588.dtsi index 6be9bf81c09c..4d66ca6c2e4c 100644 --- a/arch/arm64/boot/dts/rockchip/rk3588.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3588.dtsi @@ -80,6 +80,60 @@ i2s10_8ch: i2s@fde00000 { status = "disabled"; }; + pcie2x1l0: pcie@fe170000 { + compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x20 0x2f>; + clocks = <&cru ACLK_PCIE_1L0_MSTR>, <&cru ACLK_PCIE_1L0_SLV>, + <&cru ACLK_PCIE_1L0_DBI>, <&cru PCLK_PCIE_1L0>, + <&cru CLK_PCIE_AUX2>, <&cru CLK_PCIE1L0_PIPE>; + clock-names = "aclk_mst", "aclk_slv", + "aclk_dbi", "pclk", + "aux", "pipe"; + device_type = "pci"; + interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "sys", "pmc", "msg", "legacy", "err"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie2x1l0_intc 0>, + <0 0 0 2 &pcie2x1l0_intc 1>, + <0 0 0 3 &pcie2x1l0_intc 2>, + <0 0 0 4 &pcie2x1l0_intc 3>; + linux,pci-domain = <2>; + num-ib-windows = <8>; + num-ob-windows = <8>; + num-viewport = <4>; + max-link-speed = <2>; + msi-map = <0x2000 &its0 0x2000 0x1000>; + num-lanes = <1>; + phys = <&combphy1_ps PHY_TYPE_PCIE>; + phy-names = "pcie-phy"; + power-domains = <&power RK3588_PD_PCIE>; + ranges = <0x01000000 0x0 0xf2100000 0x0 0xf2100000 0x0 0x00100000>, + <0x02000000 0x0 0xf2200000 0x0 0xf2200000 0x0 0x00e00000>, + <0x03000000 0x0 0x40000000 0x9 0x80000000 0x0 0x40000000>; + reg = <0xa 0x40800000 0x0 0x00400000>, + <0x0 0xfe170000 0x0 0x00010000>, + <0x0 0xf2000000 0x0 0x00100000>; + reg-names = "dbi", "apb", "config"; + resets = <&cru SRST_PCIE2_POWER_UP>, <&cru SRST_P_PCIE2>; + reset-names = "pwr", "pipe"; + status = "disabled"; + + pcie2x1l0_intc: legacy-interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 240 IRQ_TYPE_EDGE_RISING 0>; + }; + }; + gmac0: ethernet@fe1b0000 { compatible = "rockchip,rk3588-gmac", "snps,dwmac-4.20a"; reg = <0x0 0xfe1b0000 0x0 0x10000>; diff --git a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi index c9f9dd2472f5..27d711d114d6 100644 --- a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi @@ -1227,6 +1227,114 @@ qos_vop_m1: qos@fdf82200 { reg = <0x0 0xfdf82200 0x0 0x20>; }; + pcie2x1l1: pcie@fe180000 { + compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x30 0x3f>; + clocks = <&cru ACLK_PCIE_1L1_MSTR>, <&cru ACLK_PCIE_1L1_SLV>, + <&cru ACLK_PCIE_1L1_DBI>, <&cru PCLK_PCIE_1L1>, + <&cru CLK_PCIE_AUX3>, <&cru CLK_PCIE1L1_PIPE>; + clock-names = "aclk_mst", "aclk_slv", + "aclk_dbi", "pclk", + "aux", "pipe"; + device_type = "pci"; + interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "sys", "pmc", "msg", "legacy", "err"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie2x1l1_intc 0>, + <0 0 0 2 &pcie2x1l1_intc 1>, + <0 0 0 3 &pcie2x1l1_intc 2>, + <0 0 0 4 &pcie2x1l1_intc 3>; + linux,pci-domain = <3>; + num-ib-windows = <8>; + num-ob-windows = <8>; + num-viewport = <4>; + max-link-speed = <2>; + msi-map = <0x3000 &its0 0x3000 0x1000>; + num-lanes = <1>; + phys = <&combphy2_psu PHY_TYPE_PCIE>; + phy-names = "pcie-phy"; + power-domains = <&power RK3588_PD_PCIE>; + ranges = <0x01000000 0x0 0xf3100000 0x0 0xf3100000 0x0 0x00100000>, + <0x02000000 0x0 0xf3200000 0x0 0xf3200000 0x0 0x00e00000>, + <0x03000000 0x0 0x40000000 0x9 0xc0000000 0x0 0x40000000>; + reg = <0xa 0x40c00000 0x0 0x00400000>, + <0x0 0xfe180000 0x0 0x00010000>, + <0x0 0xf3000000 0x0 0x00100000>; + reg-names = "dbi", "apb", "config"; + resets = <&cru SRST_PCIE3_POWER_UP>, <&cru SRST_P_PCIE3>; + reset-names = "pwr", "pipe"; + status = "disabled"; + + pcie2x1l1_intc: legacy-interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 245 IRQ_TYPE_EDGE_RISING 0>; + }; + }; + + pcie2x1l2: pcie@fe190000 { + compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x40 0x4f>; + clocks = <&cru ACLK_PCIE_1L2_MSTR>, <&cru ACLK_PCIE_1L2_SLV>, + <&cru ACLK_PCIE_1L2_DBI>, <&cru PCLK_PCIE_1L2>, + <&cru CLK_PCIE_AUX4>, <&cru CLK_PCIE1L2_PIPE>; + clock-names = "aclk_mst", "aclk_slv", + "aclk_dbi", "pclk", + "aux", "pipe"; + device_type = "pci"; + interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "sys", "pmc", "msg", "legacy", "err"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie2x1l2_intc 0>, + <0 0 0 2 &pcie2x1l2_intc 1>, + <0 0 0 3 &pcie2x1l2_intc 2>, + <0 0 0 4 &pcie2x1l2_intc 3>; + linux,pci-domain = <4>; + num-ib-windows = <8>; + num-ob-windows = <8>; + num-viewport = <4>; + max-link-speed = <2>; + msi-map = <0x4000 &its0 0x4000 0x1000>; + num-lanes = <1>; + phys = <&combphy0_ps PHY_TYPE_PCIE>; + phy-names = "pcie-phy"; + power-domains = <&power RK3588_PD_PCIE>; + ranges = <0x01000000 0x0 0xf4100000 0x0 0xf4100000 0x0 0x00100000>, + <0x02000000 0x0 0xf4200000 0x0 0xf4200000 0x0 0x00e00000>, + <0x03000000 0x0 0x40000000 0xa 0x00000000 0x0 0x40000000>; + reg = <0xa 0x41000000 0x0 0x00400000>, + <0x0 0xfe190000 0x0 0x00010000>, + <0x0 0xf4000000 0x0 0x00100000>; + reg-names = "dbi", "apb", "config"; + resets = <&cru SRST_PCIE4_POWER_UP>, <&cru SRST_P_PCIE4>; + reset-names = "pwr", "pipe"; + status = "disabled"; + + pcie2x1l2_intc: legacy-interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 250 IRQ_TYPE_EDGE_RISING 0>; + }; + }; + gmac1: ethernet@fe1c0000 { compatible = "rockchip,rk3588-gmac", "snps,dwmac-4.20a"; reg = <0x0 0xfe1c0000 0x0 0x10000>;