| Message ID | 20230718061052.1332993-5-bhupesh.sharma@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add Qualcomm SM6115 / SM4250 EUD dt-bindings & driver support | expand |
On 18/07/2023 08:10, Bhupesh Sharma wrote: > Add SM6115 / SM4250 SoC EUD support in qcom_eud driver. > > On some SoCs (like the SM6115 / SM4250 SoC), the mode manager > needs to be accessed only via the secure world (through 'scm' > calls). > > Also, the enable bit inside 'tcsr_check_reg' needs to be set > first to set the eud in 'enable' mode on these SoCs. > > Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> > --- > drivers/usb/misc/Kconfig | 2 +- > drivers/usb/misc/qcom_eud.c | 76 ++++++++++++++++++++++++++++++++++--- > 2 files changed, 72 insertions(+), 6 deletions(-) > > diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig > index 99b15b77dfd57..51eb5140caa14 100644 > --- a/drivers/usb/misc/Kconfig > +++ b/drivers/usb/misc/Kconfig > @@ -146,7 +146,7 @@ config USB_APPLEDISPLAY > > config USB_QCOM_EUD > tristate "QCOM Embedded USB Debugger(EUD) Driver" > - depends on ARCH_QCOM || COMPILE_TEST > + depends on (ARCH_QCOM && QCOM_SCM) || COMPILE_TEST > select USB_ROLE_SWITCH > help > This module enables support for Qualcomm Technologies, Inc. > diff --git a/drivers/usb/misc/qcom_eud.c b/drivers/usb/misc/qcom_eud.c > index 7f371ea1248c3..a5b28fc24116a 100644 > --- a/drivers/usb/misc/qcom_eud.c > +++ b/drivers/usb/misc/qcom_eud.c > @@ -11,9 +11,12 @@ > #include <linux/kernel.h> > #include <linux/module.h> > #include <linux/of.h> > +#include <linux/of_address.h> > +#include <linux/of_device.h> > #include <linux/platform_device.h> > #include <linux/slab.h> > #include <linux/sysfs.h> > +#include <linux/firmware/qcom/qcom_scm.h> > #include <linux/usb/role.h> > > #define EUD_REG_INT1_EN_MASK 0x0024 > @@ -30,6 +33,10 @@ > #define EUD_INT_SAFE_MODE BIT(4) > #define EUD_INT_ALL (EUD_INT_VBUS | EUD_INT_SAFE_MODE) > > +#define EUD_EN2_EN BIT(0) > +#define EUD_EN2_DISABLE (0) > +#define TCSR_CHECK_EN BIT(0) > + > struct eud_chip { > struct device *dev; > struct usb_role_switch *role_sw; > @@ -39,6 +46,7 @@ struct eud_chip { > int irq; > bool enabled; > bool usb_attached; > + phys_addr_t secure_mode_mgr; > }; > > static int enable_eud(struct eud_chip *priv) > @@ -46,7 +54,11 @@ static int enable_eud(struct eud_chip *priv) > writel(EUD_ENABLE, priv->base + EUD_REG_CSR_EUD_EN); > writel(EUD_INT_VBUS | EUD_INT_SAFE_MODE, > priv->base + EUD_REG_INT1_EN_MASK); > - writel(1, priv->mode_mgr + EUD_REG_EUD_EN2); > + > + if (priv->secure_mode_mgr) > + qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_EN); > + else > + writel(EUD_EN2_EN, priv->mode_mgr + EUD_REG_EUD_EN2); > > return usb_role_switch_set_role(priv->role_sw, USB_ROLE_DEVICE); > } > @@ -54,7 +66,11 @@ static int enable_eud(struct eud_chip *priv) > static void disable_eud(struct eud_chip *priv) > { > writel(0, priv->base + EUD_REG_CSR_EUD_EN); > - writel(0, priv->mode_mgr + EUD_REG_EUD_EN2); > + > + if (priv->secure_mode_mgr) > + qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_DISABLE); > + else > + writel(EUD_EN2_DISABLE, priv->mode_mgr + EUD_REG_EUD_EN2); > } > > static ssize_t enable_show(struct device *dev, > @@ -175,9 +191,37 @@ static void eud_role_switch_release(void *data) > usb_role_switch_put(chip->role_sw); > } > > +static int eud_find_secure_reg_addr(struct device *dev, u64 *addr) > +{ > + struct device_node *tcsr; > + struct device_node *np = dev->of_node; > + struct resource res; > + u32 offset; > + int ret; > + > + tcsr = of_parse_phandle(np, "qcom,secure-eud-reg", 0); > + if (!tcsr) > + return 0; > + > + ret = of_address_to_resource(tcsr, 0, &res); > + of_node_put(tcsr); > + if (ret) > + return ret; > + > + ret = of_property_read_u32_index(np, "qcom,secure-eud-reg", 1, &offset); > + if (ret < 0) > + return ret; > + > + *addr = res.start + offset; > + > + return 0; > +} > + > static int eud_probe(struct platform_device *pdev) > { > struct eud_chip *chip; > + struct resource *res; > + phys_addr_t tcsr_check = 0; > int ret; > > chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL); > @@ -200,9 +244,30 @@ static int eud_probe(struct platform_device *pdev) > if (IS_ERR(chip->base)) > return PTR_ERR(chip->base); > > - chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1); > - if (IS_ERR(chip->mode_mgr)) > - return PTR_ERR(chip->mode_mgr); > + /* > + * EUD block on a few Qualcomm SoCs needs secure register access. > + * Check for the same via vendor-specific dt property. > + */ > + ret = eud_find_secure_reg_addr(&pdev->dev, &tcsr_check); > + if (ret < 0) > + return ret; > + > + if (tcsr_check) { > + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); I don't understand this code. If you have syscon to eud reg, then why you are not using it, but instead map again second address space? > + if (!res) > + return dev_err_probe(chip->dev, -ENODEV, > + "failed to get secure_mode_mgr reg base\n"); > + > + chip->secure_mode_mgr = res->start; > + > + ret = qcom_scm_io_writel(tcsr_check, TCSR_CHECK_EN); That's not how syscon is used. Your bindings defined it as syscon, so are you sure you are using it correctly? Best regards, Krzysztof
Hi Bhupesh, On 7/18/2023 11:40 AM, Bhupesh Sharma wrote: > Add SM6115 / SM4250 SoC EUD support in qcom_eud driver. > > On some SoCs (like the SM6115 / SM4250 SoC), the mode manager > needs to be accessed only via the secure world (through 'scm' > calls). > > Also, the enable bit inside 'tcsr_check_reg' needs to be set > first to set the eud in 'enable' mode on these SoCs. > > Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> > --- > drivers/usb/misc/Kconfig | 2 +- > drivers/usb/misc/qcom_eud.c | 76 ++++++++++++++++++++++++++++++++++--- > 2 files changed, 72 insertions(+), 6 deletions(-) > > diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig > index 99b15b77dfd57..51eb5140caa14 100644 > --- a/drivers/usb/misc/Kconfig > +++ b/drivers/usb/misc/Kconfig > @@ -146,7 +146,7 @@ config USB_APPLEDISPLAY > > config USB_QCOM_EUD > tristate "QCOM Embedded USB Debugger(EUD) Driver" > - depends on ARCH_QCOM || COMPILE_TEST > + depends on (ARCH_QCOM && QCOM_SCM) || COMPILE_TEST > select USB_ROLE_SWITCH > help > This module enables support for Qualcomm Technologies, Inc. > diff --git a/drivers/usb/misc/qcom_eud.c b/drivers/usb/misc/qcom_eud.c > index 7f371ea1248c3..a5b28fc24116a 100644 > --- a/drivers/usb/misc/qcom_eud.c > +++ b/drivers/usb/misc/qcom_eud.c > @@ -11,9 +11,12 @@ > #include <linux/kernel.h> > #include <linux/module.h> > #include <linux/of.h> > +#include <linux/of_address.h> > +#include <linux/of_device.h> > #include <linux/platform_device.h> > #include <linux/slab.h> > #include <linux/sysfs.h> > +#include <linux/firmware/qcom/qcom_scm.h> > #include <linux/usb/role.h> > > #define EUD_REG_INT1_EN_MASK 0x0024 > @@ -30,6 +33,10 @@ > #define EUD_INT_SAFE_MODE BIT(4) > #define EUD_INT_ALL (EUD_INT_VBUS | EUD_INT_SAFE_MODE) > > +#define EUD_EN2_EN BIT(0) > +#define EUD_EN2_DISABLE (0) > +#define TCSR_CHECK_EN BIT(0) > + > struct eud_chip { > struct device *dev; > struct usb_role_switch *role_sw; > @@ -39,6 +46,7 @@ struct eud_chip { > int irq; > bool enabled; > bool usb_attached; > + phys_addr_t secure_mode_mgr; > }; > > static int enable_eud(struct eud_chip *priv) > @@ -46,7 +54,11 @@ static int enable_eud(struct eud_chip *priv) > writel(EUD_ENABLE, priv->base + EUD_REG_CSR_EUD_EN); > writel(EUD_INT_VBUS | EUD_INT_SAFE_MODE, > priv->base + EUD_REG_INT1_EN_MASK); > - writel(1, priv->mode_mgr + EUD_REG_EUD_EN2); > + > + if (priv->secure_mode_mgr) > + qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_EN); > + else > + writel(EUD_EN2_EN, priv->mode_mgr + EUD_REG_EUD_EN2); > > return usb_role_switch_set_role(priv->role_sw, USB_ROLE_DEVICE); > } > @@ -54,7 +66,11 @@ static int enable_eud(struct eud_chip *priv) > static void disable_eud(struct eud_chip *priv) > { > writel(0, priv->base + EUD_REG_CSR_EUD_EN); > - writel(0, priv->mode_mgr + EUD_REG_EUD_EN2); > + > + if (priv->secure_mode_mgr) > + qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_DISABLE); > + else > + writel(EUD_EN2_DISABLE, priv->mode_mgr + EUD_REG_EUD_EN2); > } > > static ssize_t enable_show(struct device *dev, > @@ -175,9 +191,37 @@ static void eud_role_switch_release(void *data) > usb_role_switch_put(chip->role_sw); > } > > +static int eud_find_secure_reg_addr(struct device *dev, u64 *addr) > +{ > + struct device_node *tcsr; > + struct device_node *np = dev->of_node; > + struct resource res; > + u32 offset; > + int ret; > + > + tcsr = of_parse_phandle(np, "qcom,secure-eud-reg", 0); > + if (!tcsr) > + return 0; > + > + ret = of_address_to_resource(tcsr, 0, &res); > + of_node_put(tcsr); > + if (ret) > + return ret; > + > + ret = of_property_read_u32_index(np, "qcom,secure-eud-reg", 1, &offset); > + if (ret < 0) > + return ret; > + > + *addr = res.start + offset; > + > + return 0; > +} > + > static int eud_probe(struct platform_device *pdev) > { > struct eud_chip *chip; > + struct resource *res; > + phys_addr_t tcsr_check = 0; > int ret; > > chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL); > @@ -200,9 +244,30 @@ static int eud_probe(struct platform_device *pdev) > if (IS_ERR(chip->base)) > return PTR_ERR(chip->base); > > - chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1); > - if (IS_ERR(chip->mode_mgr)) > - return PTR_ERR(chip->mode_mgr); > + /* > + * EUD block on a few Qualcomm SoCs needs secure register access. > + * Check for the same via vendor-specific dt property. > + */ > + ret = eud_find_secure_reg_addr(&pdev->dev, &tcsr_check); > + if (ret < 0) > + return ret; > + > + if (tcsr_check) { > + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); > + if (!res) > + return dev_err_probe(chip->dev, -ENODEV, > + "failed to get secure_mode_mgr reg base\n"); > + > + chip->secure_mode_mgr = res->start; There are multiple instances where the addresses are being mapped from the dt property without using the devm version. Either we should switch to the later or ensure that these addresses are unmapped in the removal path of the driver. Thanks, Souradeep > + > + ret = qcom_scm_io_writel(tcsr_check, TCSR_CHECK_EN); > + if (ret) > + return dev_err_probe(chip->dev, ret, "failed to write tcsr check reg\n"); > + } else { > + chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1); > + if (IS_ERR(chip->mode_mgr)) > + return PTR_ERR(chip->mode_mgr); > + } > > chip->irq = platform_get_irq(pdev, 0); > ret = devm_request_threaded_irq(&pdev->dev, chip->irq, handle_eud_irq, > @@ -230,6 +295,7 @@ static void eud_remove(struct platform_device *pdev) > > static const struct of_device_id eud_dt_match[] = { > { .compatible = "qcom,sc7280-eud" }, > + { .compatible = "qcom,sm6115-eud" }, > { } > }; > MODULE_DEVICE_TABLE(of, eud_dt_match);
Hi Bhupesh, kernel test robot noticed the following build errors: [auto build test ERROR on usb/usb-testing] [also build test ERROR on usb/usb-next usb/usb-linus lee-mfd/for-mfd-next linus/master v6.5-rc2 next-20230718] [cannot apply to robh/for-next lee-mfd/for-mfd-fixes] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch#_base_tree_information] url: https://github.com/intel-lab-lkp/linux/commits/Bhupesh-Sharma/dt-bindings-mfd-qcom-tcsr-Add-the-compatible-for-SM6115/20230718-190223 base: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-testing patch link: https://lore.kernel.org/r/20230718061052.1332993-5-bhupesh.sharma%40linaro.org patch subject: [PATCH v9 4/7] usb: misc: eud: Add driver support for SM6115 / SM4250 config: arm-allmodconfig (https://download.01.org/0day-ci/archive/20230719/202307191045.FMNOhyay-lkp@intel.com/config) compiler: arm-linux-gnueabi-gcc (GCC) 12.3.0 reproduce: (https://download.01.org/0day-ci/archive/20230719/202307191045.FMNOhyay-lkp@intel.com/reproduce) If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags | Reported-by: kernel test robot <lkp@intel.com> | Closes: https://lore.kernel.org/oe-kbuild-all/202307191045.FMNOhyay-lkp@intel.com/ All errors (new ones prefixed by >>): drivers/usb/misc/qcom_eud.c: In function 'eud_probe': >> drivers/usb/misc/qcom_eud.c:251:52: error: passing argument 2 of 'eud_find_secure_reg_addr' from incompatible pointer type [-Werror=incompatible-pointer-types] 251 | ret = eud_find_secure_reg_addr(&pdev->dev, &tcsr_check); | ^~~~~~~~~~~ | | | phys_addr_t * {aka unsigned int *} drivers/usb/misc/qcom_eud.c:194:62: note: expected 'u64 *' {aka 'long long unsigned int *'} but argument is of type 'phys_addr_t *' {aka 'unsigned int *'} 194 | static int eud_find_secure_reg_addr(struct device *dev, u64 *addr) | ~~~~~^~~~ cc1: some warnings being treated as errors Kconfig warnings: (for reference only) WARNING: unmet direct dependencies detected for SM_GCC_8350 Depends on [n]: COMMON_CLK [=y] && COMMON_CLK_QCOM [=m] && (ARM64 || COMPILE_TEST [=n]) Selected by [m]: - SM_VIDEOCC_8350 [=m] && COMMON_CLK [=y] && COMMON_CLK_QCOM [=m] WARNING: unmet direct dependencies detected for SM_GCC_8450 Depends on [n]: COMMON_CLK [=y] && COMMON_CLK_QCOM [=m] && (ARM64 || COMPILE_TEST [=n]) Selected by [m]: - SM_GPUCC_8450 [=m] && COMMON_CLK [=y] && COMMON_CLK_QCOM [=m] - SM_VIDEOCC_8450 [=m] && COMMON_CLK [=y] && COMMON_CLK_QCOM [=m] WARNING: unmet direct dependencies detected for SM_GCC_8550 Depends on [n]: COMMON_CLK [=y] && COMMON_CLK_QCOM [=m] && (ARM64 || COMPILE_TEST [=n]) Selected by [m]: - SM_GPUCC_8550 [=m] && COMMON_CLK [=y] && COMMON_CLK_QCOM [=m] - SM_VIDEOCC_8550 [=m] && COMMON_CLK [=y] && COMMON_CLK_QCOM [=m] vim +/eud_find_secure_reg_addr +251 drivers/usb/misc/qcom_eud.c 219 220 static int eud_probe(struct platform_device *pdev) 221 { 222 struct eud_chip *chip; 223 struct resource *res; 224 phys_addr_t tcsr_check = 0; 225 int ret; 226 227 chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL); 228 if (!chip) 229 return -ENOMEM; 230 231 chip->dev = &pdev->dev; 232 233 chip->role_sw = usb_role_switch_get(&pdev->dev); 234 if (IS_ERR(chip->role_sw)) 235 return dev_err_probe(chip->dev, PTR_ERR(chip->role_sw), 236 "failed to get role switch\n"); 237 238 ret = devm_add_action_or_reset(chip->dev, eud_role_switch_release, chip); 239 if (ret) 240 return dev_err_probe(chip->dev, ret, 241 "failed to add role switch release action\n"); 242 243 chip->base = devm_platform_ioremap_resource(pdev, 0); 244 if (IS_ERR(chip->base)) 245 return PTR_ERR(chip->base); 246 247 /* 248 * EUD block on a few Qualcomm SoCs needs secure register access. 249 * Check for the same via vendor-specific dt property. 250 */ > 251 ret = eud_find_secure_reg_addr(&pdev->dev, &tcsr_check); 252 if (ret < 0) 253 return ret; 254 255 if (tcsr_check) { 256 res = platform_get_resource(pdev, IORESOURCE_MEM, 1); 257 if (!res) 258 return dev_err_probe(chip->dev, -ENODEV, 259 "failed to get secure_mode_mgr reg base\n"); 260 261 chip->secure_mode_mgr = res->start; 262 263 ret = qcom_scm_io_writel(tcsr_check, TCSR_CHECK_EN); 264 if (ret) 265 return dev_err_probe(chip->dev, ret, "failed to write tcsr check reg\n"); 266 } else { 267 chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1); 268 if (IS_ERR(chip->mode_mgr)) 269 return PTR_ERR(chip->mode_mgr); 270 } 271 272 chip->irq = platform_get_irq(pdev, 0); 273 ret = devm_request_threaded_irq(&pdev->dev, chip->irq, handle_eud_irq, 274 handle_eud_irq_thread, IRQF_ONESHOT, NULL, chip); 275 if (ret) 276 return dev_err_probe(chip->dev, ret, "failed to allocate irq\n"); 277 278 enable_irq_wake(chip->irq); 279 280 platform_set_drvdata(pdev, chip); 281 282 return 0; 283 } 284
diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig index 99b15b77dfd57..51eb5140caa14 100644 --- a/drivers/usb/misc/Kconfig +++ b/drivers/usb/misc/Kconfig @@ -146,7 +146,7 @@ config USB_APPLEDISPLAY config USB_QCOM_EUD tristate "QCOM Embedded USB Debugger(EUD) Driver" - depends on ARCH_QCOM || COMPILE_TEST + depends on (ARCH_QCOM && QCOM_SCM) || COMPILE_TEST select USB_ROLE_SWITCH help This module enables support for Qualcomm Technologies, Inc. diff --git a/drivers/usb/misc/qcom_eud.c b/drivers/usb/misc/qcom_eud.c index 7f371ea1248c3..a5b28fc24116a 100644 --- a/drivers/usb/misc/qcom_eud.c +++ b/drivers/usb/misc/qcom_eud.c @@ -11,9 +11,12 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_device.h> #include <linux/platform_device.h> #include <linux/slab.h> #include <linux/sysfs.h> +#include <linux/firmware/qcom/qcom_scm.h> #include <linux/usb/role.h> #define EUD_REG_INT1_EN_MASK 0x0024 @@ -30,6 +33,10 @@ #define EUD_INT_SAFE_MODE BIT(4) #define EUD_INT_ALL (EUD_INT_VBUS | EUD_INT_SAFE_MODE) +#define EUD_EN2_EN BIT(0) +#define EUD_EN2_DISABLE (0) +#define TCSR_CHECK_EN BIT(0) + struct eud_chip { struct device *dev; struct usb_role_switch *role_sw; @@ -39,6 +46,7 @@ struct eud_chip { int irq; bool enabled; bool usb_attached; + phys_addr_t secure_mode_mgr; }; static int enable_eud(struct eud_chip *priv) @@ -46,7 +54,11 @@ static int enable_eud(struct eud_chip *priv) writel(EUD_ENABLE, priv->base + EUD_REG_CSR_EUD_EN); writel(EUD_INT_VBUS | EUD_INT_SAFE_MODE, priv->base + EUD_REG_INT1_EN_MASK); - writel(1, priv->mode_mgr + EUD_REG_EUD_EN2); + + if (priv->secure_mode_mgr) + qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_EN); + else + writel(EUD_EN2_EN, priv->mode_mgr + EUD_REG_EUD_EN2); return usb_role_switch_set_role(priv->role_sw, USB_ROLE_DEVICE); } @@ -54,7 +66,11 @@ static int enable_eud(struct eud_chip *priv) static void disable_eud(struct eud_chip *priv) { writel(0, priv->base + EUD_REG_CSR_EUD_EN); - writel(0, priv->mode_mgr + EUD_REG_EUD_EN2); + + if (priv->secure_mode_mgr) + qcom_scm_io_writel(priv->secure_mode_mgr + EUD_REG_EUD_EN2, EUD_EN2_DISABLE); + else + writel(EUD_EN2_DISABLE, priv->mode_mgr + EUD_REG_EUD_EN2); } static ssize_t enable_show(struct device *dev, @@ -175,9 +191,37 @@ static void eud_role_switch_release(void *data) usb_role_switch_put(chip->role_sw); } +static int eud_find_secure_reg_addr(struct device *dev, u64 *addr) +{ + struct device_node *tcsr; + struct device_node *np = dev->of_node; + struct resource res; + u32 offset; + int ret; + + tcsr = of_parse_phandle(np, "qcom,secure-eud-reg", 0); + if (!tcsr) + return 0; + + ret = of_address_to_resource(tcsr, 0, &res); + of_node_put(tcsr); + if (ret) + return ret; + + ret = of_property_read_u32_index(np, "qcom,secure-eud-reg", 1, &offset); + if (ret < 0) + return ret; + + *addr = res.start + offset; + + return 0; +} + static int eud_probe(struct platform_device *pdev) { struct eud_chip *chip; + struct resource *res; + phys_addr_t tcsr_check = 0; int ret; chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL); @@ -200,9 +244,30 @@ static int eud_probe(struct platform_device *pdev) if (IS_ERR(chip->base)) return PTR_ERR(chip->base); - chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1); - if (IS_ERR(chip->mode_mgr)) - return PTR_ERR(chip->mode_mgr); + /* + * EUD block on a few Qualcomm SoCs needs secure register access. + * Check for the same via vendor-specific dt property. + */ + ret = eud_find_secure_reg_addr(&pdev->dev, &tcsr_check); + if (ret < 0) + return ret; + + if (tcsr_check) { + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (!res) + return dev_err_probe(chip->dev, -ENODEV, + "failed to get secure_mode_mgr reg base\n"); + + chip->secure_mode_mgr = res->start; + + ret = qcom_scm_io_writel(tcsr_check, TCSR_CHECK_EN); + if (ret) + return dev_err_probe(chip->dev, ret, "failed to write tcsr check reg\n"); + } else { + chip->mode_mgr = devm_platform_ioremap_resource(pdev, 1); + if (IS_ERR(chip->mode_mgr)) + return PTR_ERR(chip->mode_mgr); + } chip->irq = platform_get_irq(pdev, 0); ret = devm_request_threaded_irq(&pdev->dev, chip->irq, handle_eud_irq, @@ -230,6 +295,7 @@ static void eud_remove(struct platform_device *pdev) static const struct of_device_id eud_dt_match[] = { { .compatible = "qcom,sc7280-eud" }, + { .compatible = "qcom,sm6115-eud" }, { } }; MODULE_DEVICE_TABLE(of, eud_dt_match);
Add SM6115 / SM4250 SoC EUD support in qcom_eud driver. On some SoCs (like the SM6115 / SM4250 SoC), the mode manager needs to be accessed only via the secure world (through 'scm' calls). Also, the enable bit inside 'tcsr_check_reg' needs to be set first to set the eud in 'enable' mode on these SoCs. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> --- drivers/usb/misc/Kconfig | 2 +- drivers/usb/misc/qcom_eud.c | 76 ++++++++++++++++++++++++++++++++++--- 2 files changed, 72 insertions(+), 6 deletions(-)