@@ -1,9 +1,12 @@
// SPDX-License-Identifier: GPL-2.0+
#include <linux/bitfield.h>
+#include <linux/bitmap.h>
+#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/nvmem-consumer.h>
#include <linux/pinctrl/consumer.h>
#include <linux/phy.h>
+#include <linux/regmap.h>
#define MTK_GPHY_ID_MT7981 0x03a29461
#define MTK_GPHY_ID_MT7988 0x03a29481
@@ -206,9 +209,42 @@
#define MTK_PHY_DA_TX_R50_PAIR_C 0x53f
#define MTK_PHY_DA_TX_R50_PAIR_D 0x540
+/* Registers on MDIO_MMD_VEND2 */
+#define MTK_PHY_LED0_ON_CTRL 0x24
+#define MTK_PHY_LED1_ON_CTRL 0x26
+#define MTK_PHY_LED_ON_MASK GENMASK(6, 0)
+#define MTK_PHY_LED_ON_LINK1000 BIT(0)
+#define MTK_PHY_LED_ON_LINK100 BIT(1)
+#define MTK_PHY_LED_ON_LINK10 BIT(2)
+#define MTK_PHY_LED_ON_LINKDOWN BIT(3)
+#define MTK_PHY_LED_ON_FDX BIT(4) /* Full duplex */
+#define MTK_PHY_LED_ON_HDX BIT(5) /* Half duplex */
+#define MTK_PHY_LED_ON_FORCE_ON BIT(6)
+#define MTK_PHY_LED_ON_POLARITY BIT(14)
+#define MTK_PHY_LED_ON_ENABLE BIT(15)
+
+#define MTK_PHY_LED0_BLINK_CTRL 0x25
+#define MTK_PHY_LED1_BLINK_CTRL 0x27
+#define MTK_PHY_LED_BLINK_1000TX BIT(0)
+#define MTK_PHY_LED_BLINK_1000RX BIT(1)
+#define MTK_PHY_LED_BLINK_100TX BIT(2)
+#define MTK_PHY_LED_BLINK_100RX BIT(3)
+#define MTK_PHY_LED_BLINK_10TX BIT(4)
+#define MTK_PHY_LED_BLINK_10RX BIT(5)
+#define MTK_PHY_LED_BLINK_COLLISION BIT(6)
+#define MTK_PHY_LED_BLINK_RX_CRC_ERR BIT(7)
+#define MTK_PHY_LED_BLINK_RX_IDLE_ERR BIT(8)
+#define MTK_PHY_LED_BLINK_FORCE_BLINK BIT(9)
+
+#define MTK_PHY_LED1_DEFAULT_POLARITIES BIT(1)
+
#define MTK_PHY_RG_BG_RASEL 0x115
#define MTK_PHY_RG_BG_RASEL_MASK GENMASK(2, 0)
+/* Register in boottrap syscon defining the initial state of the 4 PHY LEDs */
+#define RG_GPIO_MISC_TPBANK0 0x6f0
+#define RG_GPIO_MISC_TPBANK0_BOOTMODE GENMASK(11, 8)
+
/* These macro privides efuse parsing for internal phy. */
#define EFS_DA_TX_I2MPB_A(x) (((x) >> 0) & GENMASK(5, 0))
#define EFS_DA_TX_I2MPB_B(x) (((x) >> 6) & GENMASK(5, 0))
@@ -236,13 +272,6 @@ enum {
PAIR_D,
};
-enum {
- GPHY_PORT0,
- GPHY_PORT1,
- GPHY_PORT2,
- GPHY_PORT3,
-};
-
enum calibration_mode {
EFUSE_K,
SW_K
@@ -261,6 +290,18 @@ enum CAL_MODE {
SW_M
};
+#define MTK_PHY_LED_STATE_FORCE_ON BIT(0)
+#define MTK_PHY_LED_STATE_FORCE_BLINK BIT(1)
+#define MTK_PHY_LED_STATE_NETDEV BIT(2)
+struct mtk_socphy_priv {
+ unsigned long led_state;
+};
+
+struct mtk_socphy_shared {
+ u32 boottrap;
+ struct mtk_socphy_priv priv[4];
+};
+
static int mtk_socphy_read_page(struct phy_device *phydev)
{
return __phy_read(phydev, MTK_EXT_PAGE_ACCESS);
@@ -1071,6 +1112,370 @@ static int mt798x_phy_config_init(struct phy_device *phydev)
return mt798x_phy_calibration(phydev);
}
+static int mt798x_phy_hw_led_on_set(struct phy_device *phydev, u8 index,
+ bool on)
+{
+ struct mtk_socphy_priv *priv = phydev->priv;
+ u32 mask = MTK_PHY_LED_STATE_FORCE_ON << (index ? 16 : 0);
+ bool changed;
+
+ if (on)
+ changed = (test_and_set_bit(mask, &priv->led_state) != mask);
+ else
+ changed = !!test_and_clear_bit(mask, &priv->led_state);
+
+ changed |= !!test_and_clear_bit(MTK_PHY_LED_STATE_NETDEV <<
+ (index ? 16 : 0), &priv->led_state);
+ if (changed)
+ return phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ?
+ MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL,
+ MTK_PHY_LED_ON_MASK,
+ on ? MTK_PHY_LED_ON_FORCE_ON : 0);
+ else
+ return 0;
+}
+
+static int mt798x_phy_hw_led_blink_set(struct phy_device *phydev, u8 index,
+ bool blinking)
+{
+ struct mtk_socphy_priv *priv = phydev->priv;
+ u32 mask = MTK_PHY_LED_STATE_FORCE_BLINK << (index ? 16 : 0);
+ bool changed;
+
+ if (blinking)
+ changed = (test_and_set_bit(mask, &priv->led_state) != mask);
+ else
+ changed = !!test_and_clear_bit(mask, &priv->led_state);
+
+ changed |= !!test_bit(MTK_PHY_LED_STATE_NETDEV << (index ? 16 : 0), &priv->led_state);
+ if (changed)
+ return phy_write_mmd(phydev, MDIO_MMD_VEND2, index ?
+ MTK_PHY_LED1_BLINK_CTRL : MTK_PHY_LED0_BLINK_CTRL,
+ blinking ? MTK_PHY_LED_BLINK_FORCE_BLINK : 0);
+ else
+ return 0;
+}
+
+static int mt798x_phy_led_blink_set(struct phy_device *phydev, u8 index,
+ unsigned long *delay_on,
+ unsigned long *delay_off)
+{
+ bool blinking = false;
+ int err = 0;
+
+ if (index > 1)
+ return -EINVAL;
+
+ if (delay_on && delay_off && (*delay_on > 0) && (*delay_off > 0)) {
+ blinking = true;
+ *delay_on = 50;
+ *delay_off = 50;
+ }
+
+ err = mt798x_phy_hw_led_blink_set(phydev, index, blinking);
+ if (err)
+ return err;
+
+ return mt798x_phy_hw_led_on_set(phydev, index, false);
+}
+
+static int mt798x_phy_led_brightness_set(struct phy_device *phydev,
+ u8 index, enum led_brightness value)
+{
+ int err;
+
+ err = mt798x_phy_hw_led_blink_set(phydev, index, false);
+ if (err)
+ return err;
+
+ return mt798x_phy_hw_led_on_set(phydev, index, (value != LED_OFF));
+}
+
+static const unsigned long supported_triggers = (BIT(TRIGGER_NETDEV_FULL_DUPLEX) |
+ BIT(TRIGGER_NETDEV_HALF_DUPLEX) |
+ BIT(TRIGGER_NETDEV_LINK) |
+ BIT(TRIGGER_NETDEV_LINK_10) |
+ BIT(TRIGGER_NETDEV_LINK_100) |
+ BIT(TRIGGER_NETDEV_LINK_1000) |
+ BIT(TRIGGER_NETDEV_RX) |
+ BIT(TRIGGER_NETDEV_TX));
+
+static int mt798x_phy_led_hw_is_supported(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ if (index > 1)
+ return -EINVAL;
+
+ /* All combinations of the supported triggers are allowed */
+ if (rules & ~supported_triggers)
+ return -EOPNOTSUPP;
+
+ return 0;
+};
+
+static int mt798x_phy_led_hw_control_get(struct phy_device *phydev, u8 index,
+ unsigned long *rules)
+{
+ u32 blink_mask = MTK_PHY_LED_STATE_FORCE_BLINK << (index ? 16 : 0);
+ u32 netdev_mask = MTK_PHY_LED_STATE_NETDEV << (index ? 16 : 0);
+ u32 on_mask = MTK_PHY_LED_STATE_FORCE_ON << (index ? 16 : 0);
+ struct mtk_socphy_priv *priv = phydev->priv;
+ int on, blink;
+
+ if (index > 1)
+ return -EINVAL;
+
+ on = phy_read_mmd(phydev, MDIO_MMD_VEND2,
+ index ? MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL);
+
+ if (on < 0)
+ return -EIO;
+
+ blink = phy_read_mmd(phydev, MDIO_MMD_VEND2,
+ index ? MTK_PHY_LED1_BLINK_CTRL :
+ MTK_PHY_LED0_BLINK_CTRL);
+ if (blink < 0)
+ return -EIO;
+
+ if ((on & (MTK_PHY_LED_ON_LINK1000 | MTK_PHY_LED_ON_LINK100 |
+ MTK_PHY_LED_ON_LINK10)) ||
+ (blink & (MTK_PHY_LED_BLINK_1000RX | MTK_PHY_LED_BLINK_100RX |
+ MTK_PHY_LED_BLINK_10RX | MTK_PHY_LED_BLINK_1000TX |
+ MTK_PHY_LED_BLINK_100TX | MTK_PHY_LED_BLINK_10TX)))
+ set_bit(netdev_mask, &priv->led_state);
+ else
+ clear_bit(netdev_mask, &priv->led_state);
+
+ if (on & MTK_PHY_LED_ON_FORCE_ON)
+ set_bit(on_mask, &priv->led_state);
+ else
+ clear_bit(on_mask, &priv->led_state);
+
+ if (blink & MTK_PHY_LED_BLINK_FORCE_BLINK)
+ set_bit(blink_mask, &priv->led_state);
+ else
+ clear_bit(blink_mask, &priv->led_state);
+
+ if (!rules)
+ return 0;
+
+ if (on & (MTK_PHY_LED_ON_LINK1000 | MTK_PHY_LED_ON_LINK100 | MTK_PHY_LED_ON_LINK10))
+ *rules |= BIT(TRIGGER_NETDEV_LINK);
+
+ if (on & MTK_PHY_LED_ON_LINK10)
+ *rules |= BIT(TRIGGER_NETDEV_LINK_10);
+
+ if (on & MTK_PHY_LED_ON_LINK100)
+ *rules |= BIT(TRIGGER_NETDEV_LINK_100);
+
+ if (on & MTK_PHY_LED_ON_LINK1000)
+ *rules |= BIT(TRIGGER_NETDEV_LINK_1000);
+
+ if (on & MTK_PHY_LED_ON_FDX)
+ *rules |= BIT(TRIGGER_NETDEV_FULL_DUPLEX);
+
+ if (on & MTK_PHY_LED_ON_HDX)
+ *rules |= BIT(TRIGGER_NETDEV_HALF_DUPLEX);
+
+ if (blink & (MTK_PHY_LED_BLINK_1000RX | MTK_PHY_LED_BLINK_100RX | MTK_PHY_LED_BLINK_10RX))
+ *rules |= BIT(TRIGGER_NETDEV_RX);
+
+ if (blink & (MTK_PHY_LED_BLINK_1000TX | MTK_PHY_LED_BLINK_100TX | MTK_PHY_LED_BLINK_10TX))
+ *rules |= BIT(TRIGGER_NETDEV_TX);
+
+ return 0;
+};
+
+static int mt798x_phy_led_hw_control_set(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ u32 mask = MTK_PHY_LED_STATE_NETDEV << (index ? 16 : 0);
+ struct mtk_socphy_priv *priv = phydev->priv;
+ u16 on = 0, blink = 0;
+ int ret;
+
+ if (index > 1)
+ return -EINVAL;
+
+ if (rules & BIT(TRIGGER_NETDEV_FULL_DUPLEX))
+ on |= MTK_PHY_LED_ON_FDX;
+
+ if (rules & BIT(TRIGGER_NETDEV_HALF_DUPLEX))
+ on |= MTK_PHY_LED_ON_HDX;
+
+ if (rules & (BIT(TRIGGER_NETDEV_LINK_10) | BIT(TRIGGER_NETDEV_LINK)))
+ on |= MTK_PHY_LED_ON_LINK10;
+
+ if (rules & (BIT(TRIGGER_NETDEV_LINK_100) | BIT(TRIGGER_NETDEV_LINK)))
+ on |= MTK_PHY_LED_ON_LINK100;
+
+ if (rules & (BIT(TRIGGER_NETDEV_LINK_1000) | BIT(TRIGGER_NETDEV_LINK)))
+ on |= MTK_PHY_LED_ON_LINK1000;
+
+ if (rules & BIT(TRIGGER_NETDEV_RX)) {
+ blink |= MTK_PHY_LED_BLINK_10RX |
+ MTK_PHY_LED_BLINK_100RX |
+ MTK_PHY_LED_BLINK_1000RX;
+ }
+
+ if (rules & BIT(TRIGGER_NETDEV_TX)) {
+ blink |= MTK_PHY_LED_BLINK_10TX |
+ MTK_PHY_LED_BLINK_100TX |
+ MTK_PHY_LED_BLINK_1000TX;
+ }
+
+ if (blink || on)
+ set_bit(mask, &priv->led_state);
+ else
+ clear_bit(mask, &priv->led_state);
+
+ ret = phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ?
+ MTK_PHY_LED1_ON_CTRL :
+ MTK_PHY_LED0_ON_CTRL,
+ MTK_PHY_LED_ON_FDX |
+ MTK_PHY_LED_ON_HDX |
+ MTK_PHY_LED_ON_LINK10 |
+ MTK_PHY_LED_ON_LINK100 |
+ MTK_PHY_LED_ON_LINK1000,
+ on);
+
+ if (ret)
+ return ret;
+
+ return phy_write_mmd(phydev, MDIO_MMD_VEND2, index ?
+ MTK_PHY_LED1_BLINK_CTRL :
+ MTK_PHY_LED0_BLINK_CTRL, blink);
+};
+
+static bool mt7988_phy_led_get_polarity(struct phy_device *phydev, int led_num)
+{
+ struct mtk_socphy_shared *priv = phydev->shared->priv;
+ u32 polarities;
+
+ if (led_num == 0)
+ polarities = ~(priv->boottrap);
+ else
+ polarities = MTK_PHY_LED1_DEFAULT_POLARITIES;
+
+ if (polarities & BIT(phydev->mdio.addr))
+ return true;
+
+ return false;
+}
+
+static int mt7988_phy_fix_leds_polarities(struct phy_device *phydev)
+{
+ struct pinctrl *pinctrl;
+ int index;
+
+ /* Setup LED polarity according to bootstrap use of LED pins */
+ for (index = 0; index < 2; ++index)
+ phy_modify_mmd(phydev, MDIO_MMD_VEND2, index ?
+ MTK_PHY_LED1_ON_CTRL : MTK_PHY_LED0_ON_CTRL,
+ MTK_PHY_LED_ON_POLARITY,
+ mt7988_phy_led_get_polarity(phydev, index) ?
+ MTK_PHY_LED_ON_POLARITY : 0);
+
+ /* Only now setup pinctrl to avoid bogus blinking */
+ pinctrl = devm_pinctrl_get_select(&phydev->mdio.dev, "gbe-led");
+ if (IS_ERR(pinctrl))
+ dev_err(&phydev->mdio.bus->dev, "Failed to setup PHY LED pinctrl\n");
+
+ return 0;
+}
+
+static int mt7988_phy_probe_shared(struct phy_device *phydev)
+{
+ struct device_node *np = dev_of_node(&phydev->mdio.bus->dev);
+ struct mtk_socphy_shared *shared = phydev->shared->priv;
+ struct regmap *regmap;
+ u32 reg;
+ int ret;
+
+ /* The LED0 of the 4 PHYs in MT7988 are wired to SoC pins LED_A, LED_B,
+ * LED_C and LED_D respectively. At the same time those pins are used to
+ * bootstrap configuration of the reference clock source (LED_A),
+ * DRAM DDRx16b x2/x1 (LED_B) and boot device (LED_C, LED_D).
+ * In practise this is done using a LED and a resistor pulling the pin
+ * either to GND or to VIO.
+ * The detected value at boot time is accessible at run-time using the
+ * TPBANK0 register located in the gpio base of the pinctrl, in order
+ * to read it here it needs to be referenced by a phandle called
+ * 'mediatek,pio' in the MDIO bus hosting the PHY.
+ * The 4 bits in TPBANK0 are kept as package shared data and are used to
+ * set LED polarity for each of the LED0.
+ */
+ regmap = syscon_regmap_lookup_by_phandle(np, "mediatek,pio");
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ ret = regmap_read(regmap, RG_GPIO_MISC_TPBANK0, ®);
+ if (ret)
+ return ret;
+
+ shared->boottrap = FIELD_GET(RG_GPIO_MISC_TPBANK0_BOOTMODE, reg);
+
+ return 0;
+}
+
+static void mt798x_phy_leds_state_init(struct phy_device *phydev)
+{
+ int i;
+
+ for (i = 0; i < 2; ++i)
+ mt798x_phy_led_hw_control_get(phydev, i, NULL);
+}
+
+static int mt7988_phy_probe(struct phy_device *phydev)
+{
+ struct mtk_socphy_shared *shared;
+ struct mtk_socphy_priv *priv;
+ int err;
+
+ if (phydev->mdio.addr > 3)
+ return -EINVAL;
+
+ err = devm_phy_package_join(&phydev->mdio.dev, phydev, 0,
+ sizeof(struct mtk_socphy_shared));
+ if (err)
+ return err;
+
+ if (phy_package_probe_once(phydev)) {
+ err = mt7988_phy_probe_shared(phydev);
+ if (err)
+ return err;
+ }
+
+ shared = phydev->shared->priv;
+ priv = &shared->priv[phydev->mdio.addr];
+
+ phydev->priv = priv;
+
+ mt798x_phy_leds_state_init(phydev);
+
+ err = mt7988_phy_fix_leds_polarities(phydev);
+ if (err)
+ return err;
+
+ return mt798x_phy_calibration(phydev);
+}
+
+static int mt7981_phy_probe(struct phy_device *phydev)
+{
+ struct mtk_socphy_priv *priv;
+
+ priv = devm_kzalloc(&phydev->mdio.dev, sizeof(struct mtk_socphy_priv),
+ GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ mt798x_phy_leds_state_init(phydev);
+
+ phydev->priv = priv;
+
+ return mt798x_phy_calibration(phydev);
+}
+
static struct phy_driver mtk_socphy_driver[] = {
{
PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981),
@@ -1078,11 +1483,16 @@ static struct phy_driver mtk_socphy_driver[] = {
.config_init = mt798x_phy_config_init,
.config_intr = genphy_no_config_intr,
.handle_interrupt = genphy_handle_interrupt_no_ack,
- .probe = mt798x_phy_calibration,
+ .probe = mt7981_phy_probe,
.suspend = genphy_suspend,
.resume = genphy_resume,
.read_page = mtk_socphy_read_page,
.write_page = mtk_socphy_write_page,
+ .led_blink_set = mt798x_phy_led_blink_set,
+ .led_brightness_set = mt798x_phy_led_brightness_set,
+ .led_hw_is_supported = mt798x_phy_led_hw_is_supported,
+ .led_hw_control_set = mt798x_phy_led_hw_control_set,
+ .led_hw_control_get = mt798x_phy_led_hw_control_get,
},
{
PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7988),
@@ -1090,11 +1500,16 @@ static struct phy_driver mtk_socphy_driver[] = {
.config_init = mt798x_phy_config_init,
.config_intr = genphy_no_config_intr,
.handle_interrupt = genphy_handle_interrupt_no_ack,
- .probe = mt798x_phy_calibration,
+ .probe = mt7988_phy_probe,
.suspend = genphy_suspend,
.resume = genphy_resume,
.read_page = mtk_socphy_read_page,
.write_page = mtk_socphy_write_page,
+ .led_blink_set = mt798x_phy_led_blink_set,
+ .led_brightness_set = mt798x_phy_led_brightness_set,
+ .led_hw_is_supported = mt798x_phy_led_hw_is_supported,
+ .led_hw_control_set = mt798x_phy_led_hw_control_set,
+ .led_hw_control_get = mt798x_phy_led_hw_control_get,
},
};
Implement netdev trigger and primitive bliking offloading as well as simple set_brigthness function for both PHY LEDs of the in-SoC PHYs found in MT7981 and MT7988. On MT7988 it is necessary to read the boottrap register and apply LED polarities accordingly to get uniform behavior from all LEDs. Signed-off-by: Daniel Golle <daniel@makrotopia.org> --- drivers/net/phy/mediatek-ge-soc.c | 433 +++++++++++++++++++++++++++++- 1 file changed, 424 insertions(+), 9 deletions(-)