diff mbox series

[2/7] ARM: dts: qcom: add common device tree for MSM8x26-based Lumia phones

Message ID 20230811213728.23726-3-rayyan@ansari.sh (mailing list archive)
State Superseded
Headers show
Series Initial support for MSM8x26 Lumias | expand

Commit Message

Rayyan Ansari Aug. 11, 2023, 9:35 p.m. UTC
Add a common device tree for Lumias based on the Qualcomm MSM8x26
family of chipsets.

Currently supports:
- Framebuffer
- Touchscreen
- Keys
- Regulators
- MMC
- USB
- UART

Co-authored-by: Dominik Kobinski <dominikkobinski314@gmail.com>
Co-authored-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Co-authored-by: Jack Matthews <jm5112356@gmail.com>
Signed-off-by: Dominik Kobinski <dominikkobinski314@gmail.com>
Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Signed-off-by: Jack Matthews <jm5112356@gmail.com>
Signed-off-by: Rayyan Ansari <rayyan@ansari.sh>
---
 .../qcom/qcom-msm8226-microsoft-common.dtsi   | 332 ++++++++++++++++++
 1 file changed, 332 insertions(+)
 create mode 100644 arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-common.dtsi

Comments

Konrad Dybcio Aug. 11, 2023, 11:02 p.m. UTC | #1
On 11.08.2023 23:35, Rayyan Ansari wrote:
> Add a common device tree for Lumias based on the Qualcomm MSM8x26
> family of chipsets.
> 
> Currently supports:
> - Framebuffer
> - Touchscreen
> - Keys
> - Regulators
> - MMC
> - USB
> - UART
> 
> Co-authored-by: Dominik Kobinski <dominikkobinski314@gmail.com>
> Co-authored-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
> Co-authored-by: Jack Matthews <jm5112356@gmail.com>
> Signed-off-by: Dominik Kobinski <dominikkobinski314@gmail.com>
> Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
> Signed-off-by: Jack Matthews <jm5112356@gmail.com>
> Signed-off-by: Rayyan Ansari <rayyan@ansari.sh>
> ---
Would be really nice if you could squash it with patch 3 so that
this code is immediately compilable.

[...]

> +	gpio_keys: gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&gpio_keys_active>;
property-n
property-names

[...]

> +	reserved-memory {
> +		ranges;
That's already there in soc dtsi

> +
> +		smem_region: smem@fa00000 {
Swap the subnodes to keep the nodes ordered by unit address
> +			reg = <0xfa00000 0x100000>;
> +			no-map;
> +		};
> +
> +		display_reserved: framebuffer@3200000 {
> +			reg = <0x3200000 0x800000>;
> +			no-map;
> +		};
> +	};
> +};
> +
> +&blsp1_i2c5 {
> +	status = "okay";
> +
> +	touchscreen@4b {
> +		compatible = "syna,rmi4-i2c";
> +		reg = <0x4b>;
> +
> +		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
> +		vdd-supply = <&pm8226_l15>;
> +		vio-supply = <&pm8226_l6>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&touchscreen_on>;
ditto

> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		rmi4-f01@1 {
> +			reg = <0x01>;
> +			syna,nosleep-mode = <1>;
> +		};
> +
> +		rmi4-f11@11 {
> +			reg = <0x11>;
> +			syna,sensor-type = <1>;
> +		};
> +	};
> +};
[...]

> +
> +&tlmm {
> +	gpio_keys_active: gpio-keys-active {
Run `make CHECK_DTBS=1 qcom/msm8226-something-lumia` and fix the warnings
before Krzysztof gets angry :D

Konrad
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-common.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-common.dtsi
new file mode 100644
index 000000000000..b49ccf867964
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-common.dtsi
@@ -0,0 +1,332 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Common Board Device Tree for Microsoft MSM8x26-based Lumias
+ *
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+#include <dt-bindings/input/input.h>
+
+/*
+ * Delete all generic (msm8226.dtsi) reserved
+ * memory mappings which are different on these devices.
+ */
+/delete-node/ &smem_region;
+
+/ {
+	aliases {
+		mmc0 = &sdhc_1; /* eMMC */
+		mmc1 = &sdhc_2; /* microSD */
+		display0 = &framebuffer0;
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		stdout-path = "display0";
+
+		framebuffer0: framebuffer@3200000 {
+			compatible = "simple-framebuffer";
+			reg = <0x3200000 0x800000>;
+			format = "a8r8g8b8";
+			width = <720>;
+			height = <1280>;
+			stride = <(720 * 4)>;
+
+			clocks = <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MDSS_BYTE0_CLK>,
+				 <&mmcc MDSS_MDP_CLK>,
+				 <&mmcc MDSS_PCLK0_CLK>,
+				 <&mmcc MDSS_VSYNC_CLK>;
+			power-domains = <&mmcc MDSS_GDSC>;
+		};
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_active>;
+
+		label = "GPIO Buttons";
+
+		volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	/*
+	 * This device being a WP platform has a different
+	 * memory layout than other Android based devices.
+	 * This smem memory region is directly copied from
+	 * the original UEFI firmware.
+	 */
+	reserved-memory {
+		ranges;
+
+		smem_region: smem@fa00000 {
+			reg = <0xfa00000 0x100000>;
+			no-map;
+		};
+
+		display_reserved: framebuffer@3200000 {
+			reg = <0x3200000 0x800000>;
+			no-map;
+		};
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+
+	touchscreen@4b {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x4b>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l15>;
+		vio-supply = <&pm8226_l6>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchscreen_on>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f11@11 {
+			reg = <0x11>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&pm8226_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pm8226_vib {
+	status = "okay";
+};
+
+&rpm_requests {
+	pm8226-regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		/* These values were taken from the original firmware DSDT */
+		pm8226_s1: s1 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2100000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2075000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <2000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	status = "okay";
+};
+
+&usb {
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
+
+&tlmm {
+	gpio_keys_active: gpio-keys-active {
+		pins = "gpio106", "gpio107", "gpio108";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	touchscreen_on: touchscreen-on {
+		irq {
+			pins = "gpio17";
+			function = "gpio";
+
+			drive-strength = <8>;
+			bias-pull-up;
+			input-enable;
+		};
+
+		reset {
+			pins = "gpio16";
+			function = "gpio";
+
+			drive-strength = <8>;
+			bias-disable;
+			output-high;
+		};
+	};
+};