deleted file mode 100644
@@ -1,461 +0,0 @@
-Broadcom BCM281xx Pin Controller
-
-This is a pin controller for the Broadcom BCM281xx SoC family, which includes
-BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs.
-
-=== Pin Controller Node ===
-
-Required Properties:
-
-- compatible: Must be "brcm,bcm11351-pinctrl"
-- reg: Base address of the PAD Controller register block and the size
- of the block.
-
-For example, the following is the bare minimum node:
-
- pinctrl@35004800 {
- compatible = "brcm,bcm11351-pinctrl";
- reg = <0x35004800 0x430>;
- };
-
-As a pin controller device, in addition to the required properties, this node
-should also contain the pin configuration nodes that client devices reference,
-if any.
-
-=== Pin Configuration Node ===
-
-Each pin configuration node is a sub-node of the pin controller node and is a
-container of an arbitrary number of subnodes, called pin group nodes in this
-document.
-
-Please refer to the pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the definition of a
-"pin configuration node".
-
-=== Pin Group Node ===
-
-A pin group node specifies the desired pin mux and/or pin configuration for an
-arbitrary number of pins. The name of the pin group node is optional and not
-used.
-
-A pin group node only affects the properties specified in the node, and has no
-effect on any properties that are omitted.
-
-The pin group node accepts a subset of the generic pin config properties. For
-details generic pin config properties, please refer to pinctrl-bindings.txt
-and <include/linux/pinctrl/pinconfig-generic.h>.
-
-Each pin controlled by this pin controller belong to one of three types:
-Standard, I2C, and HDMI. Each type accepts a different set of pin config
-properties. A list of pins and their types is provided below.
-
-Required Properties (applicable to all pins):
-
-- pins: Multiple strings. Specifies the name(s) of one or more pins to
- be configured by this node.
-
-Optional Properties (for standard pins):
-
-- function: String. Specifies the pin mux selection. Values
- must be one of: "alt1", "alt2", "alt3", "alt4"
-- input-schmitt-enable: No arguments. Enable schmitt-trigger mode.
-- input-schmitt-disable: No arguments. Disable schmitt-trigger mode.
-- bias-pull-up: No arguments. Pull up on pin.
-- bias-pull-down: No arguments. Pull down on pin.
-- bias-disable: No arguments. Disable pin bias.
-- slew-rate: Integer. Meaning depends on configured pin mux:
- *_SCL or *_SDA:
- 0: Standard(100kbps)& Fast(400kbps) mode
- 1: Highspeed (3.4Mbps) mode
- IC_DM or IC_DP:
- 0: normal slew rate
- 1: fast slew rate
- Otherwise:
- 0: fast slew rate
- 1: normal slew rate
-- input-enable: No arguments. Enable input (does not affect
- output.)
-- input-disable: No arguments. Disable input (does not affect
- output.)
-- drive-strength: Integer. Drive strength in mA. Valid values are
- 2, 4, 6, 8, 10, 12, 14, 16 mA.
-
-Optional Properties (for I2C pins):
-
-- function: String. Specifies the pin mux selection. Values
- must be one of: "alt1", "alt2", "alt3", "alt4"
-- bias-pull-up: Integer. Pull up strength in Ohm. There are 3
- pull-up resistors (1.2k, 1.8k, 2.7k) available
- in parallel for I2C pins, so the valid values
- are: 568, 720, 831, 1080, 1200, 1800, 2700 Ohm.
-- bias-disable: No arguments. Disable pin bias.
-- slew-rate: Integer. Meaning depends on configured pin mux:
- *_SCL or *_SDA:
- 0: Standard(100kbps)& Fast(400kbps) mode
- 1: Highspeed (3.4Mbps) mode
- IC_DM or IC_DP:
- 0: normal slew rate
- 1: fast slew rate
- Otherwise:
- 0: fast slew rate
- 1: normal slew rate
-- input-enable: No arguments. Enable input (does not affect
- output.)
-- input-disable: No arguments. Disable input (does not affect
- output.)
-
-Optional Properties (for HDMI pins):
-
-- function: String. Specifies the pin mux selection. Values
- must be one of: "alt1", "alt2", "alt3", "alt4"
-- slew-rate: Integer. Controls slew rate.
- 0: Standard(100kbps)& Fast(400kbps) mode
- 1: Highspeed (3.4Mbps) mode
-- input-enable: No arguments. Enable input (does not affect
- output.)
-- input-disable: No arguments. Disable input (does not affect
- output.)
-
-Example:
-// pin controller node
-pinctrl@35004800 {
- compatible = "brcm,bcm11351-pinctrl";
- reg = <0x35004800 0x430>;
-
- // pin configuration node
- dev_a_default: dev_a_active {
- //group node defining 1 standard pin
- grp_1 {
- pins = "std_pin1";
- function = "alt1";
- input-schmitt-enable;
- bias-disable;
- slew-rate = <1>;
- drive-strength = <4>;
- };
-
- // group node defining 2 I2C pins
- grp_2 {
- pins = "i2c_pin1", "i2c_pin2";
- function = "alt2";
- bias-pull-up = <720>;
- input-enable;
- };
-
- // group node defining 2 HDMI pins
- grp_3 {
- pins = "hdmi_pin1", "hdmi_pin2";
- function = "alt3";
- slew-rate = <1>;
- };
-
- // other pin group nodes
- ...
- };
-
- // other pin configuration nodes
- ...
-};
-
-In the example above, "dev_a_active" is a pin configuration node with a number
-of sub-nodes. In the pin group node "grp_1", one pin, "std_pin1", is defined in
-the "pins" property. Thus, the remaining properties in the "grp_1" node applies
-only to this pin, including the following settings:
- - setting pinmux to "alt1"
- - enabling schmitt-trigger (hystersis) mode
- - disabling pin bias
- - setting the slew-rate to 1
- - setting the drive strength to 4 mA
-Note that neither "input-enable" nor "input-disable" was specified - the pinctrl
-subsystem will therefore leave this property unchanged from whatever state it
-was in before applying these changes.
-
-The "pins" property in the pin group node "grp_2" specifies two pins -
-"i2c_pin1" and "i2c_pin2"; the remaining properties in this pin group node,
-therefore, applies to both of these pins. The properties include:
- - setting pinmux to "alt2"
- - setting pull-up resistance to 720 Ohm (ie. enabling 1.2k and 1.8k resistors
- in parallel)
- - enabling both pins' input
-"slew-rate" is not specified in this pin group node, so the slew-rate for these
-pins are left as-is.
-
-Finally, "grp_3" defines two HDMI pins. The following properties are applied to
-both pins:
- - setting pinmux to "alt3"
- - setting slew-rate to 1; for HDMI pins, this corresponds to the 3.4 Mbps
- Highspeed mode
-The input is neither enabled or disabled, and is left untouched.
-
-=== Pin Names and Type ===
-
-The following are valid pin names and their pin types:
-
- "adcsync", Standard
- "bat_rm", Standard
- "bsc1_scl", I2C
- "bsc1_sda", I2C
- "bsc2_scl", I2C
- "bsc2_sda", I2C
- "classgpwr", Standard
- "clk_cx8", Standard
- "clkout_0", Standard
- "clkout_1", Standard
- "clkout_2", Standard
- "clkout_3", Standard
- "clkreq_in_0", Standard
- "clkreq_in_1", Standard
- "cws_sys_req1", Standard
- "cws_sys_req2", Standard
- "cws_sys_req3", Standard
- "digmic1_clk", Standard
- "digmic1_dq", Standard
- "digmic2_clk", Standard
- "digmic2_dq", Standard
- "gpen13", Standard
- "gpen14", Standard
- "gpen15", Standard
- "gpio00", Standard
- "gpio01", Standard
- "gpio02", Standard
- "gpio03", Standard
- "gpio04", Standard
- "gpio05", Standard
- "gpio06", Standard
- "gpio07", Standard
- "gpio08", Standard
- "gpio09", Standard
- "gpio10", Standard
- "gpio11", Standard
- "gpio12", Standard
- "gpio13", Standard
- "gpio14", Standard
- "gps_pablank", Standard
- "gps_tmark", Standard
- "hdmi_scl", HDMI
- "hdmi_sda", HDMI
- "ic_dm", Standard
- "ic_dp", Standard
- "kp_col_ip_0", Standard
- "kp_col_ip_1", Standard
- "kp_col_ip_2", Standard
- "kp_col_ip_3", Standard
- "kp_row_op_0", Standard
- "kp_row_op_1", Standard
- "kp_row_op_2", Standard
- "kp_row_op_3", Standard
- "lcd_b_0", Standard
- "lcd_b_1", Standard
- "lcd_b_2", Standard
- "lcd_b_3", Standard
- "lcd_b_4", Standard
- "lcd_b_5", Standard
- "lcd_b_6", Standard
- "lcd_b_7", Standard
- "lcd_g_0", Standard
- "lcd_g_1", Standard
- "lcd_g_2", Standard
- "lcd_g_3", Standard
- "lcd_g_4", Standard
- "lcd_g_5", Standard
- "lcd_g_6", Standard
- "lcd_g_7", Standard
- "lcd_hsync", Standard
- "lcd_oe", Standard
- "lcd_pclk", Standard
- "lcd_r_0", Standard
- "lcd_r_1", Standard
- "lcd_r_2", Standard
- "lcd_r_3", Standard
- "lcd_r_4", Standard
- "lcd_r_5", Standard
- "lcd_r_6", Standard
- "lcd_r_7", Standard
- "lcd_vsync", Standard
- "mdmgpio0", Standard
- "mdmgpio1", Standard
- "mdmgpio2", Standard
- "mdmgpio3", Standard
- "mdmgpio4", Standard
- "mdmgpio5", Standard
- "mdmgpio6", Standard
- "mdmgpio7", Standard
- "mdmgpio8", Standard
- "mphi_data_0", Standard
- "mphi_data_1", Standard
- "mphi_data_2", Standard
- "mphi_data_3", Standard
- "mphi_data_4", Standard
- "mphi_data_5", Standard
- "mphi_data_6", Standard
- "mphi_data_7", Standard
- "mphi_data_8", Standard
- "mphi_data_9", Standard
- "mphi_data_10", Standard
- "mphi_data_11", Standard
- "mphi_data_12", Standard
- "mphi_data_13", Standard
- "mphi_data_14", Standard
- "mphi_data_15", Standard
- "mphi_ha0", Standard
- "mphi_hat0", Standard
- "mphi_hat1", Standard
- "mphi_hce0_n", Standard
- "mphi_hce1_n", Standard
- "mphi_hrd_n", Standard
- "mphi_hwr_n", Standard
- "mphi_run0", Standard
- "mphi_run1", Standard
- "mtx_scan_clk", Standard
- "mtx_scan_data", Standard
- "nand_ad_0", Standard
- "nand_ad_1", Standard
- "nand_ad_2", Standard
- "nand_ad_3", Standard
- "nand_ad_4", Standard
- "nand_ad_5", Standard
- "nand_ad_6", Standard
- "nand_ad_7", Standard
- "nand_ale", Standard
- "nand_cen_0", Standard
- "nand_cen_1", Standard
- "nand_cle", Standard
- "nand_oen", Standard
- "nand_rdy_0", Standard
- "nand_rdy_1", Standard
- "nand_wen", Standard
- "nand_wp", Standard
- "pc1", Standard
- "pc2", Standard
- "pmu_int", Standard
- "pmu_scl", I2C
- "pmu_sda", I2C
- "rfst2g_mtsloten3g", Standard
- "rgmii_0_rx_ctl", Standard
- "rgmii_0_rxc", Standard
- "rgmii_0_rxd_0", Standard
- "rgmii_0_rxd_1", Standard
- "rgmii_0_rxd_2", Standard
- "rgmii_0_rxd_3", Standard
- "rgmii_0_tx_ctl", Standard
- "rgmii_0_txc", Standard
- "rgmii_0_txd_0", Standard
- "rgmii_0_txd_1", Standard
- "rgmii_0_txd_2", Standard
- "rgmii_0_txd_3", Standard
- "rgmii_1_rx_ctl", Standard
- "rgmii_1_rxc", Standard
- "rgmii_1_rxd_0", Standard
- "rgmii_1_rxd_1", Standard
- "rgmii_1_rxd_2", Standard
- "rgmii_1_rxd_3", Standard
- "rgmii_1_tx_ctl", Standard
- "rgmii_1_txc", Standard
- "rgmii_1_txd_0", Standard
- "rgmii_1_txd_1", Standard
- "rgmii_1_txd_2", Standard
- "rgmii_1_txd_3", Standard
- "rgmii_gpio_0", Standard
- "rgmii_gpio_1", Standard
- "rgmii_gpio_2", Standard
- "rgmii_gpio_3", Standard
- "rtxdata2g_txdata3g1", Standard
- "rtxen2g_txdata3g2", Standard
- "rxdata3g0", Standard
- "rxdata3g1", Standard
- "rxdata3g2", Standard
- "sdio1_clk", Standard
- "sdio1_cmd", Standard
- "sdio1_data_0", Standard
- "sdio1_data_1", Standard
- "sdio1_data_2", Standard
- "sdio1_data_3", Standard
- "sdio4_clk", Standard
- "sdio4_cmd", Standard
- "sdio4_data_0", Standard
- "sdio4_data_1", Standard
- "sdio4_data_2", Standard
- "sdio4_data_3", Standard
- "sim_clk", Standard
- "sim_data", Standard
- "sim_det", Standard
- "sim_resetn", Standard
- "sim2_clk", Standard
- "sim2_data", Standard
- "sim2_det", Standard
- "sim2_resetn", Standard
- "sri_c", Standard
- "sri_d", Standard
- "sri_e", Standard
- "ssp_extclk", Standard
- "ssp0_clk", Standard
- "ssp0_fs", Standard
- "ssp0_rxd", Standard
- "ssp0_txd", Standard
- "ssp2_clk", Standard
- "ssp2_fs_0", Standard
- "ssp2_fs_1", Standard
- "ssp2_fs_2", Standard
- "ssp2_fs_3", Standard
- "ssp2_rxd_0", Standard
- "ssp2_rxd_1", Standard
- "ssp2_txd_0", Standard
- "ssp2_txd_1", Standard
- "ssp3_clk", Standard
- "ssp3_fs", Standard
- "ssp3_rxd", Standard
- "ssp3_txd", Standard
- "ssp4_clk", Standard
- "ssp4_fs", Standard
- "ssp4_rxd", Standard
- "ssp4_txd", Standard
- "ssp5_clk", Standard
- "ssp5_fs", Standard
- "ssp5_rxd", Standard
- "ssp5_txd", Standard
- "ssp6_clk", Standard
- "ssp6_fs", Standard
- "ssp6_rxd", Standard
- "ssp6_txd", Standard
- "stat_1", Standard
- "stat_2", Standard
- "sysclken", Standard
- "traceclk", Standard
- "tracedt00", Standard
- "tracedt01", Standard
- "tracedt02", Standard
- "tracedt03", Standard
- "tracedt04", Standard
- "tracedt05", Standard
- "tracedt06", Standard
- "tracedt07", Standard
- "tracedt08", Standard
- "tracedt09", Standard
- "tracedt10", Standard
- "tracedt11", Standard
- "tracedt12", Standard
- "tracedt13", Standard
- "tracedt14", Standard
- "tracedt15", Standard
- "txdata3g0", Standard
- "txpwrind", Standard
- "uartb1_ucts", Standard
- "uartb1_urts", Standard
- "uartb1_urxd", Standard
- "uartb1_utxd", Standard
- "uartb2_urxd", Standard
- "uartb2_utxd", Standard
- "uartb3_ucts", Standard
- "uartb3_urts", Standard
- "uartb3_urxd", Standard
- "uartb3_utxd", Standard
- "uartb4_ucts", Standard
- "uartb4_urts", Standard
- "uartb4_urxd", Standard
- "uartb4_utxd", Standard
- "vc_cam1_scl", I2C
- "vc_cam1_sda", I2C
- "vc_cam2_scl", I2C
- "vc_cam2_sda", I2C
- "vc_cam3_scl", I2C
- "vc_cam3_sda", I2C
new file mode 100644
@@ -0,0 +1,259 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/brcm,bcm11351-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom BCM281xx pin controller
+
+maintainers:
+ - Florian Fainelli <florian.fainelli@broadcom.com>
+ - Ray Jui <rjui@broadcom.com>
+ - Scott Branden <sbranden@broadcom.com>
+
+allOf:
+ - $ref: pinctrl.yaml#
+
+properties:
+ compatible:
+ const: brcm,bcm11351-pinctrl
+
+ reg:
+ maxItems: 1
+
+patternProperties:
+ '-pins$':
+ type: object
+ additionalProperties: false
+
+ patternProperties:
+ '-grp[0-9]$':
+ type: object
+ unevaluatedProperties: false
+
+ properties:
+ pins:
+ description:
+ Specifies the name(s) of one or more pins to be configured by
+ this node.
+ items:
+ enum: [ adcsync, bat_rm, bsc1_scl, bsc1_sda, bsc2_scl, bsc2_sda,
+ classgpwr, clk_cx8, clkout_0, clkout_1, clkout_2,
+ clkout_3, clkreq_in_0, clkreq_in_1, cws_sys_req1,
+ cws_sys_req2, cws_sys_req3, digmic1_clk, digmic1_dq,
+ digmic2_clk, digmic2_dq, gpen13, gpen14, gpen15, gpio00,
+ gpio01, gpio02, gpio03, gpio04, gpio05, gpio06, gpio07,
+ gpio08, gpio09, gpio10, gpio11, gpio12, gpio13, gpio14,
+ gps_pablank, gps_tmark, hdmi_scl, hdmi_sda, ic_dm, ic_dp,
+ kp_col_ip_0, kp_col_ip_1, kp_col_ip_2, kp_col_ip_3,
+ kp_row_op_0, kp_row_op_1, kp_row_op_2, kp_row_op_3,
+ lcd_b_0, lcd_b_1, lcd_b_2, lcd_b_3, lcd_b_4, lcd_b_5,
+ lcd_b_6, lcd_b_7, lcd_g_0, lcd_g_1, lcd_g_2, lcd_g_3,
+ lcd_g_4, lcd_g_5, lcd_g_6, lcd_g_7, lcd_hsync, lcd_oe,
+ lcd_pclk, lcd_r_0, lcd_r_1, lcd_r_2, lcd_r_3, lcd_r_4,
+ lcd_r_5, lcd_r_6, lcd_r_7, lcd_vsync, mdmgpio0, mdmgpio1,
+ mdmgpio2, mdmgpio3, mdmgpio4, mdmgpio5, mdmgpio6,
+ mdmgpio7, mdmgpio8, mphi_data_0, mphi_data_1, mphi_data_2,
+ mphi_data_3, mphi_data_4, mphi_data_5, mphi_data_6,
+ mphi_data_7, mphi_data_8, mphi_data_9, mphi_data_10,
+ mphi_data_11, mphi_data_12, mphi_data_13, mphi_data_14,
+ mphi_data_15, mphi_ha0, mphi_hat0, mphi_hat1, mphi_hce0_n,
+ mphi_hce1_n, mphi_hrd_n, mphi_hwr_n, mphi_run0, mphi_run1,
+ mtx_scan_clk, mtx_scan_data, nand_ad_0, nand_ad_1,
+ nand_ad_2, nand_ad_3, nand_ad_4, nand_ad_5, nand_ad_6,
+ nand_ad_7, nand_ale, nand_cen_0, nand_cen_1, nand_cle,
+ nand_oen, nand_rdy_0, nand_rdy_1, nand_wen, nand_wp, pc1,
+ pc2, pmu_int, pmu_scl, pmu_sda, rfst2g_mtsloten3g,
+ rgmii_0_rx_ctl, rgmii_0_rxc, rgmii_0_rxd_0, rgmii_0_rxd_1,
+ rgmii_0_rxd_2, rgmii_0_rxd_3, rgmii_0_tx_ctl, rgmii_0_txc,
+ rgmii_0_txd_0, rgmii_0_txd_1, rgmii_0_txd_2,
+ rgmii_0_txd_3, rgmii_1_rx_ctl, rgmii_1_rxc, rgmii_1_rxd_0,
+ rgmii_1_rxd_1, rgmii_1_rxd_2, rgmii_1_rxd_3,
+ rgmii_1_tx_ctl, rgmii_1_txc, rgmii_1_txd_0, rgmii_1_txd_1,
+ rgmii_1_txd_2, rgmii_1_txd_3, rgmii_gpio_0, rgmii_gpio_1,
+ rgmii_gpio_2, rgmii_gpio_3, rtxdata2g_txdata3g1,
+ rtxen2g_txdata3g2, rxdata3g0, rxdata3g1, rxdata3g2,
+ sdio1_clk, sdio1_cmd, sdio1_data_0, sdio1_data_1,
+ sdio1_data_2, sdio1_data_3, sdio4_clk, sdio4_cmd,
+ sdio4_data_0, sdio4_data_1, sdio4_data_2, sdio4_data_3,
+ sim_clk, sim_data, sim_det, sim_resetn, sim2_clk,
+ sim2_data, sim2_det, sim2_resetn, sri_c, sri_d, sri_e,
+ ssp_extclk, ssp0_clk, ssp0_fs, ssp0_rxd, ssp0_txd,
+ ssp2_clk, ssp2_fs_0, ssp2_fs_1, ssp2_fs_2, ssp2_fs_3,
+ ssp2_rxd_0, ssp2_rxd_1, ssp2_txd_0, ssp2_txd_1, ssp3_clk,
+ ssp3_fs, ssp3_rxd, ssp3_txd, ssp4_clk, ssp4_fs, ssp4_rxd,
+ ssp4_txd, ssp5_clk, ssp5_fs, ssp5_rxd, ssp5_txd, ssp6_clk,
+ ssp6_fs, ssp6_rxd, ssp6_txd, stat_1, stat_2, sysclken,
+ traceclk, tracedt00, tracedt01, tracedt02, tracedt03,
+ tracedt04, tracedt05, tracedt06, tracedt07, tracedt08
+ tracedt09, tracedt10, tracedt11, tracedt12, tracedt13
+ tracedt14, tracedt15, txdata3g0, txpwrind, uartb1_ucts,
+ uartb1_urts, uartb1_urxd, uartb1_utxd, uartb2_urxd,
+ uartb2_utxd, uartb3_ucts, uartb3_urts, uartb3_urxd,
+ uartb3_utxd, uartb4_ucts, uartb4_urts, uartb4_urxd,
+ uartb4_utxd, vc_cam1_scl, vc_cam1_sda, vc_cam2_scl,
+ vc_cam2_sda, vc_cam3_scl, vc_cam3_sda ]
+
+ function:
+ description:
+ Specifies the pin mux selection.
+ enum: [ alt1, alt2, alt3, alt4 ]
+
+ slew-rate:
+ description: |
+ Meaning depends on configured pin mux:
+ *_scl or *_sda:
+ 0: Standard (100 kbps) & Fast (400 kbps) mode
+ 1: Highspeed (3.4 Mbps) mode
+ ic_dm or ic_dp:
+ 0: normal slew rate
+ 1: fast slew rate
+ Otherwise:
+ 0: fast slew rate
+ 1: normal slew rate
+
+ bias-disable: true
+ input-disable: true
+ input-enable: true
+
+ required:
+ - pins
+
+ allOf:
+ - $ref: pincfg-node.yaml#
+
+ # Optional properties for standard pins
+ - if:
+ properties:
+ pins:
+ contains:
+ enum: [ adcsync, bat_rm, classgpwr, clk_cx8, clkout_0,
+ clkout_1, clkout_2, clkout_3, clkreq_in_0,
+ clkreq_in_1, cws_sys_req1, cws_sys_req2,
+ cws_sys_req3, digmic1_clk, digmic1_dq, digmic2_clk,
+ digmic2_dq, gpen13, gpen14, gpen15, gpio00, gpio01,
+ gpio02, gpio03, gpio04, gpio05, gpio06, gpio07,
+ gpio08, gpio09, gpio10, gpio11, gpio12, gpio13,
+ gpio14, gps_pablank, gps_tmark, ic_dm, ic_dp,
+ kp_col_ip_0, kp_col_ip_1, kp_col_ip_2, kp_col_ip_3,
+ kp_row_op_0, kp_row_op_1, kp_row_op_2, kp_row_op_3,
+ lcd_b_0, lcd_b_1, lcd_b_2, lcd_b_3, lcd_b_4, lcd_b_5,
+ lcd_b_6, lcd_b_7, lcd_g_0, lcd_g_1, lcd_g_2, lcd_g_3,
+ lcd_g_4, lcd_g_5, lcd_g_6, lcd_g_7, lcd_hsync,
+ lcd_oe, lcd_pclk, lcd_r_0, lcd_r_1, lcd_r_2,
+ lcd_r_3, lcd_r_4, lcd_r_5, lcd_r_6, lcd_r_7,
+ lcd_vsync, mdmgpio0, mdmgpio1, mdmgpio2, mdmgpio3,
+ mdmgpio4, mdmgpio5, mdmgpio6, mdmgpio7, mdmgpio8,
+ mphi_data_0, mphi_data_1, mphi_data_2, mphi_data_3,
+ mphi_data_4, mphi_data_5, mphi_data_6, mphi_data_7,
+ mphi_data_8, mphi_data_9, mphi_data_10,
+ mphi_data_11, mphi_data_12, mphi_data_13,
+ mphi_data_14, mphi_data_15, mphi_ha0, mphi_hat0,
+ mphi_hat1, mphi_hce0_n, mphi_hce1_n, mphi_hrd_n,
+ mphi_hwr_n, mphi_run0, mphi_run1, mtx_scan_clk,
+ mtx_scan_data, nand_ad_0, nand_ad_1, nand_ad_2,
+ nand_ad_3, nand_ad_4, nand_ad_5, nand_ad_6,
+ nand_ad_7, nand_ale, nand_cen_0, nand_cen_1,
+ nand_cle, nand_oen, nand_rdy_0, nand_rdy_1,
+ nand_wen, nand_wp, pc1, pc2, pmu_int,
+ rfst2g_mtsloten3g, rgmii_0_rx_ctl, rgmii_0_rxc,
+ rgmii_0_rxd_0, rgmii_0_rxd_1, rgmii_0_rxd_2,
+ rgmii_0_rxd_3, rgmii_0_tx_ctl, rgmii_0_txc,
+ rgmii_0_txd_0, rgmii_0_txd_1, rgmii_0_txd_2,
+ rgmii_0_txd_3, rgmii_1_rx_ctl, rgmii_1_rxc,
+ rgmii_1_rxd_0, rgmii_1_rxd_1, rgmii_1_rxd_2,
+ rgmii_1_rxd_3, rgmii_1_tx_ctl, rgmii_1_txc,
+ rgmii_1_txd_0, rgmii_1_txd_1, rgmii_1_txd_2,
+ rgmii_1_txd_3, rgmii_gpio_0, rgmii_gpio_1,
+ rgmii_gpio_2, rgmii_gpio_3, rtxdata2g_txdata3g1,
+ rtxen2g_txdata3g2, rxdata3g0, rxdata3g1, rxdata3g2,
+ sdio1_clk, sdio1_cmd, sdio1_data_0, sdio1_data_1,
+ sdio1_data_2, sdio1_data_3, sdio4_clk, sdio4_cmd,
+ sdio4_data_0, sdio4_data_1, sdio4_data_2,
+ sdio4_data_3, sim_clk, sim_data, sim_det,
+ sim_resetn, sim2_clk, sim2_data, sim2_det,
+ sim2_resetn, sri_c, sri_d, sri_e, ssp_extclk,
+ ssp0_clk, ssp0_fs, ssp0_rxd, ssp0_txd, ssp2_clk,
+ ssp2_fs_0, ssp2_fs_1, ssp2_fs_2, ssp2_fs_3,
+ ssp2_rxd_0, ssp2_rxd_1, ssp2_txd_0, ssp2_txd_1,
+ ssp3_clk, ssp3_fs, ssp3_rxd, ssp3_txd, ssp4_clk,
+ ssp4_fs, ssp4_rxd, ssp4_txd, ssp5_clk, ssp5_fs,
+ ssp5_rxd, ssp5_txd, ssp6_clk, ssp6_fs, ssp6_rxd,
+ ssp6_txd, stat_1, stat_2, sysclken, traceclk,
+ tracedt00, tracedt01, tracedt02, tracedt03,
+ tracedt04, tracedt05, tracedt06, tracedt07,
+ tracedt08, tracedt09, tracedt10, tracedt11,
+ tracedt12, tracedt13, tracedt14, tracedt15,
+ txdata3g0, txpwrind, uartb1_ucts, uartb1_urts,
+ uartb1_urxd, uartb1_utxd, uartb2_urxd, uartb2_utxd,
+ uartb3_ucts, uartb3_urts, uartb3_urxd, uartb3_utxd,
+ uartb4_ucts, uartb4_urts, uartb4_urxd, uartb4_utxd ]
+ then:
+ properties:
+ drive-strength:
+ enum: [ 2, 4, 6, 8, 10, 12, 14, 16 ]
+
+ bias-disable: true
+ bias-pull-up: true
+ bias-pull-down: true
+ input-schmitt-enable: true
+ input-schmitt-disable: true
+
+ # Optional properties for I2C pins
+ - if:
+ properties:
+ pins:
+ contains:
+ enum: [ bsc1_scl, bsc1_sda, bsc2_scl, bsc2_sda, pmu_scl,
+ pmu_sda, vc_cam1_scl, vc_cam1_sda, vc_cam2_scl,
+ vc_cam2_sda, vc_cam3_scl, vc_cam3_sda ]
+ then:
+ properties:
+ bias-pull-up:
+ description:
+ There are 3 pull-up resistors (1.2k, 1.8k, 2.7k) available
+ in parallel for I2C pins.
+ enum: [ 568, 720, 831, 1080, 1200, 1800, 2700 ]
+
+ bias-disable: true
+
+required:
+ - compatible
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ pinctrl@35004800 {
+ compatible = "brcm,bcm11351-pinctrl";
+ reg = <0x35004800 0x430>;
+
+ dev-a-active-pins {
+ /* group node defining 1 standard pin */
+ std-grp0 {
+ pins = "gpio00";
+ function = "alt1";
+ input-schmitt-enable;
+ bias-disable;
+ slew-rate = <1>;
+ drive-strength = <4>;
+ };
+
+ /* group node defining 2 I2C pins */
+ i2c-grp0 {
+ pins = "bsc1_scl", "bsc1_sda";
+ function = "alt2";
+ bias-pull-up = <720>;
+ input-enable;
+ };
+
+ /* group node defining 2 HDMI pins */
+ hdmi-grp0 {
+ pins = "hdmi_scl", "hdmi_sda";
+ function = "alt3";
+ slew-rate = <1>;
+ };
+ };
+ };
+...
Convert Broadcom BCM281xx pin controller bindings to DT schema. Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com> --- .../pinctrl/brcm,bcm11351-pinctrl.txt | 461 ------------------ .../pinctrl/brcm,bcm11351-pinctrl.yaml | 259 ++++++++++ 2 files changed, 259 insertions(+), 461 deletions(-) delete mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.yaml