@@ -208,6 +208,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8250-sony-xperia-edo-pdx203.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8250-sony-xperia-edo-pdx206.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8250-xiaomi-elish-boe.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8250-xiaomi-elish-csot.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm8250-xiaomi-pipa.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8350-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8350-microsoft-surface-duo2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8350-mtp.dtb
new file mode 100644
@@ -0,0 +1,623 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2023 luka177 <lukapanio@gmail.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/arm/qcom,ids.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8250.dtsi"
+#include "pm8150.dtsi"
+#include "pm8150b.dtsi"
+#include "pm8150l.dtsi"
+#include "pm8009.dtsi"
+
+/*
+ * Delete following upstream (sm8250.dtsi) reserved
+ * memory mappings which are different on this device.
+ */
+/delete-node/ &adsp_mem;
+/delete-node/ &cdsp_secure_heap;
+/delete-node/ &slpi_mem;
+/delete-node/ &spss_mem;
+/delete-node/ &xbl_aop_mem;
+
+/ {
+
+ model = "Xiaomi Pad 6";
+ compatible = "xiaomi,pipa", "qcom,sm8250";
+
+ chassis-type = "tablet";
+
+ /* required for bootloader to select correct board */
+ qcom,msm-id = <QCOM_ID_SM8250 0x20001>; /* SM8250 v2.1 */
+ qcom,board-id = <0x34 0>;
+
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ framebuffer: framebuffer@9c000000 {
+ compatible = "simple-framebuffer";
+ reg = <0x0 0x9c000000 0x0 0x2300000>;
+ width = <1800>;
+ height = <2880>;
+ stride = <(1800 * 4)>;
+ format = "a8r8g8b8";
+ };
+ };
+
+ battery_l: battery-l {
+ compatible = "simple-battery";
+ voltage-min-design-microvolt = <3870000>;
+ energy-full-design-microwatt-hours = <16700000>;
+ charge-full-design-microamp-hours = <4420000>;
+ };
+
+ battery_r: battery-r {
+ compatible = "simple-battery";
+ voltage-min-design-microvolt = <3870000>;
+ energy-full-design-microwatt-hours = <16700000>;
+ charge-full-design-microamp-hours = <4420000>;
+ };
+
+ bl_vddpos_5p5: bl-vddpos-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "bl_vddpos_5p5";
+ regulator-min-microvolt = <5500000>;
+ regulator-max-microvolt = <5500000>;
+ regulator-enable-ramp-delay = <233>;
+ gpio = <&tlmm 130 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ bl_vddneg_5p5: bl-vddneg-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "bl_vddneg_5p5";
+ regulator-min-microvolt = <5500000>;
+ regulator-max-microvolt = <5500000>;
+ regulator-enable-ramp-delay = <233>;
+ gpio = <&tlmm 131 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&vol_up_n>;
+
+ key-vol-up {
+ label = "Volume Up";
+ gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ /* S6c is really ebi.lvl but it's there for supply map completeness sake. */
+ vreg_s6c_0p88: smpc6-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s6c_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-always-on;
+ vin-supply = <&vph_pwr>;
+ };
+
+ reserved-memory {
+ xbl_aop_mem: xbl-aop@80700000 {
+ reg = <0x0 0x80600000 0x0 0x260000>;
+ no-map;
+ };
+
+ slpi_mem: slpi@88c00000 {
+ reg = <0x0 0x88c00000 0x0 0x2f00000>;
+ no-map;
+ };
+
+ adsp_mem: adsp@8bb00000 {
+ reg = <0x0 0x8bb00000 0x0 0x2500000>;
+ no-map;
+ };
+
+ spss_mem: spss@8e000000 {
+ reg = <0x0 0x8e000000 0x0 0x100000>;
+ no-map;
+ };
+
+ cdsp_secure_heap: cdsp-secure-heap@8e100000 {
+ reg = <0x0 0x8e100000 0x0 0x4600000>;
+ no-map;
+ };
+
+ cont_splash_mem: cont-splash@9c000000 {
+ reg = <0x0 0x9c000000 0x0 0x2300000>;
+ no-map;
+ };
+
+ ramoops@b0000000 {
+ compatible = "ramoops";
+ reg = <0x0 0xb0000000 0x0 0x400000>;
+ record-size = <0x1000>;
+ console-size = <0x200000>;
+ ecc-size = <16>;
+ no-map;
+ };
+ };
+};
+
+&adsp {
+ firmware-name = "qcom/sm8250/xiaomi/pipa/adsp.mbn";
+ status = "okay";
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+ vdd-l1-l8-l11-supply = <&vreg_s6c_0p88>;
+ vdd-l2-l10-supply = <&vreg_bob>;
+ vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p95>;
+ vdd-l6-l9-supply = <&vreg_s8c_1p35>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>;
+ vdd-l13-l16-l17-supply = <&vreg_bob>;
+
+ /* (S1+S2+S3) - cx.lvl (ARC) */
+
+ vreg_s4a_1p8: smps4 {
+ regulator-name = "vreg_s4a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5a_1p9: smps5 {
+ regulator-name = "vreg_s5a_1p9";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <2040000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s6a_0p95: smps6 {
+ regulator-name = "vreg_s6a_0p95";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1128000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2a_3p1: ldo2 {
+ regulator-name = "vreg_l2a_3p1";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3a_0p9: ldo3 {
+ regulator-name = "vreg_l3a_0p9";
+ regulator-min-microvolt = <928000>;
+ regulator-max-microvolt = <932000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L4 - lmx.lvl (ARC) */
+
+ vreg_l5a_0p88: ldo5 {
+ regulator-name = "vreg_l5a_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6a_1p2: ldo6 {
+ regulator-name = "vreg_l6a_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L7 is unused. */
+
+ vreg_l9a_1p2: ldo9 {
+ regulator-name = "vreg_l9a_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L10 is unused, L11 - lcx.lvl (ARC) */
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-name = "vreg_l12a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L13 is unused. */
+
+ vreg_l14a_1p88: ldo14 {
+ regulator-name = "vreg_l14a_1p88";
+ regulator-min-microvolt = <1880000>;
+ regulator-max-microvolt = <1880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L15 & L16 are unused. */
+
+ vreg_l17a_3p0: ldo17 {
+ regulator-name = "vreg_l17a_3p0";
+ regulator-min-microvolt = <2496000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l18a_0p9: ldo18 {
+ regulator-name = "vreg_l18a_0p9";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8150l-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-l1-l8-supply = <&vreg_s4a_1p8>;
+ vdd-l2-l3-supply = <&vreg_s8c_1p35>;
+ vdd-l4-l5-l6-supply = <&vreg_bob>;
+ vdd-l7-l11-supply = <&vreg_bob>;
+ vdd-l9-l10-supply = <&vreg_bob>;
+ vdd-bob-supply = <&vph_pwr>;
+
+ vreg_bob: bob {
+ regulator-name = "vreg_bob";
+ regulator-min-microvolt = <3350000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ };
+
+ /*
+ * S1-S6 are ARCs:
+ * (S1+S2) - gfx.lvl,
+ * S3 - mx.lvl,
+ * (S4+S5) - mmcx.lvl,
+ * S6 - ebi.lvl
+ */
+
+ vreg_s7c_0p35: smps7 {
+ regulator-name = "vreg_s7c_0p35";
+ regulator-min-microvolt = <348000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s8c_1p35: smps8 {
+ regulator-name = "vreg_s8c_1p35";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1c_1p8: ldo1 {
+ regulator-name = "vreg_l1c_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L2-4 are unused. */
+
+ vreg_l5c_1p8: ldo5 {
+ regulator-name = "vreg_l5c_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6c_2p9: ldo6 {
+ regulator-name = "vreg_l6c_2p9";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7c_2p85: ldo7 {
+ regulator-name = "vreg_l7c_2p85";
+ regulator-min-microvolt = <2856000>;
+ regulator-max-microvolt = <3104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8c_1p8: ldo8 {
+ regulator-name = "vreg_l8c_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9c_2p9: ldo9 {
+ regulator-name = "vreg_l9c_2p9";
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10c_3p3: ldo10 {
+ regulator-name = "vreg_l10c_3p3";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11c_3p0: ldo11 {
+ regulator-name = "vreg_l11c_3p0";
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pm8009-rpmh-regulators";
+ qcom,pmic-id = "f";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vreg_bob>;
+ vdd-l2-supply = <&vreg_s8c_1p35>;
+ vdd-l5-l6-supply = <&vreg_bob>;
+ vdd-l7-supply = <&vreg_s4a_1p8>;
+
+ vreg_s1f_1p2: smps1 {
+ regulator-name = "vreg_s1f_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s2f_0p5: smps2 {
+ regulator-name = "vreg_s2f_0p5";
+ regulator-min-microvolt = <512000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L1 is unused. */
+
+ vreg_l2f_1p3: ldo2 {
+ regulator-name = "vreg_l2f_1p3";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L3 & L4 are unused. */
+
+ vreg_l5f_2p8: ldo5 {
+ regulator-name = "vreg_l5f_2p85";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6f_2p8: ldo6 {
+ regulator-name = "vreg_l6f_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7f_1p8: ldo7 {
+ regulator-name = "vreg_l7f_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&cdsp {
+ firmware-name = "qcom/sm8250/xiaomi/pipa/cdsp.mbn";
+ status = "okay";
+};
+
+&gmu {
+ status = "okay";
+};
+
+&gpi_dma0 {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&gpi_dma2 {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+
+ zap-shader {
+ memory-region = <&gpu_mem>;
+ firmware-name = "qcom/sm8250/xiaomi/pipa/a650_zap.mbn";
+ };
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ fuel-gauge@55 {
+ compatible = "ti,bq27z561";
+ reg = <0x55>;
+ monitored-battery = <&battery_r>;
+ };
+};
+
+&i2c11 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ backlight: backlight@11 {
+ compatible = "kinetic,ktz8866";
+ reg = <0x11>;
+ vddpos-supply = <&bl_vddpos_5p5>;
+ vddneg-supply = <&bl_vddneg_5p5>;
+ enable-gpios = <&tlmm 139 GPIO_ACTIVE_HIGH>;
+ current-num-sinks = <5>;
+ kinetic,current-ramp-delay-ms = <128>;
+ kinetic,led-enable-ramp-delay-ms = <1>;
+ kinetic,enable-lcd-bias;
+ };
+};
+
+&i2c13 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ fuel-gauge@55 {
+ compatible = "ti,bq27z561";
+ reg = <0x55>;
+ monitored-battery = <&battery_l>;
+ };
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l5a_0p88>;
+ vdda-pll-supply = <&vreg_l9a_1p2>;
+ status = "okay";
+};
+
+&pm8150_gpios {
+ vol_up_n: vol-up-n-state {
+ pins = "gpio6";
+ function = "normal";
+ power-source = <1>;
+ input-enable;
+ bias-pull-up;
+ };
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&qupv3_id_2 {
+ status = "okay";
+};
+
+&slpi {
+ firmware-name = "qcom/sm8250/xiaomi/pipa/slpi.mbn";
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+ vdda-pll-supply = <&vreg_l5a_0p88>;
+ vdda18-supply = <&vreg_l12a_1p8>;
+ vdda33-supply = <&vreg_l2a_3p1>;
+ status = "okay";
+};
+
+&usb_1_qmpphy {
+ status = "okay";
+ vdda-phy-supply = <&vreg_l9a_1p2>;
+ vdda-pll-supply = <&vreg_l18a_0p9>;
+};
+
+&ufs_mem_hc {
+ vcc-supply = <&vreg_l17a_3p0>;
+ vcc-max-microamp = <800000>;
+ vccq-supply = <&vreg_l6a_1p2>;
+ vccq-max-microamp = <800000>;
+ vccq2-supply = <&vreg_s4a_1p8>;
+ vccq2-max-microamp = <800000>;
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l5a_0p88>;
+ vdda-pll-supply = <&vreg_l9a_1p2>;
+ status = "okay";
+};
+
+&venus {
+ firmware-name = "qcom/sm8250/xiaomi/pipa/venus.mbn";
+ status = "okay";
+};
Initial support for Xiaomi Pad 6 tablet, that have sm8250 soc. Signed-off-by: Luka Panio <lukapanio@gmail.com> --- v2: Update commit message. Drop reserved gpio's as this device in reality do not have gpio, and pins are not protected. v3: Update commit message. v4: Update commit message. v5: Update commit message. v6: Update commit message. v7: Fix typo in "chassis-type", remove useless newlines, update license --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/sm8250-xiaomi-pipa.dts | 623 ++++++++++++++++++ 2 files changed, 624 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8250-xiaomi-pipa.dts