diff mbox series

[v4,2/2] iio: adc: ad7173: add AD7173 driver

Message ID 20231116134655.21052-2-user@HYB-hhAwRlzzMZb (mailing list archive)
State Superseded
Headers show
Series [v4,1/2] dt-bindings: adc: add AD7173 | expand

Commit Message

Ceclan, Dumitru Nov. 16, 2023, 1:46 p.m. UTC
From: Dumitru Ceclan <mitrutzceclan@gmail.com>

The AD7173 family offer a complete integrated Sigma-Delta ADC solution
which can be used in high precision, low noise single channel
applications or higher speed multiplexed applications. The Sigma-Delta
ADC is intended primarily for measurement of signals close to DC but also
delivers outstanding performance with input bandwidths out to ~10kHz.

Reviewed-by: Michael Walle <michael@walle.cc> # for gpio-regmap
Signed-off-by: Dumitru Ceclan <mitrutzceclan@gmail.com>
---
V3 -> V4
 - cleaned up includes
 - add ad7173_gpio_disable(), include to devm actions
 - remove iio_device_claim_direct_mode() from update_scan_mode()
 - always set differential iio_chan attribute to true, retain bipolar info only in private struct
 - store multiple regulators in state for voltage references
 - compute read_raw offset depending on channel used reference
 - configure channel setup using selected reference
 - add ad7173_get_ref_voltage_milli() 
 - clean up ad7173_fw_sparse_channel_config() changing array access of channel structs to pointers
 - retain chip name in st->info structure
 - use spi_device_get_match_data() in probe

 drivers/iio/adc/Kconfig  |  13 +
 drivers/iio/adc/Makefile |   1 +
 drivers/iio/adc/ad7173.c | 936 +++++++++++++++++++++++++++++++++++++++
 3 files changed, 950 insertions(+)
 create mode 100644 drivers/iio/adc/ad7173.c

Comments

Andy Shevchenko Nov. 20, 2023, 1 p.m. UTC | #1
On Thu, Nov 16, 2023 at 03:46:55PM +0200, mitrutzceclan wrote:
> From: Dumitru Ceclan <mitrutzceclan@gmail.com>
> 
> The AD7173 family offer a complete integrated Sigma-Delta ADC solution
> which can be used in high precision, low noise single channel
> applications or higher speed multiplexed applications. The Sigma-Delta
> ADC is intended primarily for measurement of signals close to DC but also
> delivers outstanding performance with input bandwidths out to ~10kHz.

...

> +	help
> +	  Say yes here to build support for Analog Devices AD7173 and similar ADC
> +	  (currently supported: AD7172-2, AD7173-8, AD7175-2, AD7176-2).

This is hard to maintain, list it one model per a single line.

> +	  To compile this driver as a module, choose M here: the module will be
> +	  called ad7173.

...

+ array_size.h

> +#include <linux/bitfield.h>
> +#include <linux/bitmap.h>

> +#include <linux/bits.h>

This is guaranteed to be included by one from the above (don't remember
by heart which one or even both).

+ container_of.h

> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/err.h>
> +#include <linux/gpio/driver.h>
> +#include <linux/interrupt.h>

> +#include <linux/kernel.h>

How is this being used (as not a proxy)?

> +#include <linux/module.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/property.h>
> +#include <linux/regmap.h>
> +#include <linux/gpio/regmap.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/slab.h>
> +#include <linux/spi/spi.h>
> +#include <linux/units.h>

...

> +#define AD7173_CH_ADDRESS(pos, neg) \
> +	(FIELD_PREP(AD7173_CH_SETUP_AINPOS_MASK, pos) |\

Space before \ here and everywhere else in multi-line definitions.

> +	 FIELD_PREP(AD7173_CH_SETUP_AINNEG_MASK, neg))

...

> +#define AD7173_VOLTAGE_INT_REF_MICROV	2500000

MICROV --> uV (yes, with small letter), it's a common use for Amperes, Volts,
etc.

...

> +struct ad7173_channel_config {
> +	bool live;
> +	u8 cfg_slot;
> +	/* Following fields are used to compare equality. Bipolar must be first */
> +	bool bipolar;
> +	bool input_buf;
> +	u8 odr;
> +	u8 ref_sel;

If you group better by types, it might save a few bytes on the architectures /
compilers where bool != byte.

> +};

...

> +	st->reg_gpiocon_regmap = devm_regmap_init_spi(st->sd.spi, &ad7173_regmap_config);
> +	if (IS_ERR(st->reg_gpiocon_regmap)) {
> +		return dev_err_probe(dev, PTR_ERR(st->reg_gpiocon_regmap),
> +				     "Unable to init regmap\n");
> +	}

{} are not needed, can also be written as

	st->reg_gpiocon_regmap = devm_regmap_init_spi(st->sd.spi, &ad7173_regmap_config);
	ret = PTR_ERR_OR_ZERO(st->reg_gpiocon_regmap);
	if (ret)
		return dev_err_probe(dev, ret, "Unable to init regmap\n");

...

> +	st->gpio_regmap = devm_gpio_regmap_register(dev, &gpio_regmap);
> +	if (IS_ERR(st->gpio_regmap)) {
> +		return dev_err_probe(dev, PTR_ERR(st->gpio_regmap),
> +				     "Unable to init gpio-regmap\n");
> +	}

Ditto.

...

> +static struct ad7173_channel_config *ad7173_find_live_config
> +	(struct ad7173_state *st, struct ad7173_channel_config *cfg)

This is strange indentation.

Perhaps

static struct ad7173_channel_config *
ad7173_find_live_config(struct ad7173_state *st, struct ad7173_channel_config *cfg)

?

...

> +	offset = offsetof(struct ad7173_channel_config, cfg_slot) +
> +		 sizeof(cfg->cfg_slot);

Isn't it a offsetofend() from stddef.h?

> +	cmp_size = sizeof(*cfg) - offset;

sizeof_field() from the above mentioned header?

...

> +	for (i = 0; i < st->num_channels; i++) {
> +		cfg_aux = &st->channels[i].cfg;
> +
> +		if (cfg_aux->live && !memcmp(&cfg->bipolar, &cfg_aux->bipolar,
> +					     cmp_size))

I would split this on logic operator, it will be easier to read.

> +			return cfg_aux;
> +	}

...

> +	free_cfg_slot = find_first_zero_bit(st->cfg_slots_status,
> +					    st->info->num_configs);
> +	if (free_cfg_slot == st->info->num_configs)
> +		free_cfg_slot = ad7173_free_config_slot_lru(st);
> +
> +	set_bit(free_cfg_slot, st->cfg_slots_status);
> +	cfg->cfg_slot = free_cfg_slot;

Looks like reinvention of IDA.

...

> +	struct ad7173_state *st = iio_priv(indio_dev);
> +	unsigned int id;
> +	u8 buf[AD7173_RESET_LENGTH];
> +	int ret;

Reversed xmas tree order?

	struct ad7173_state *st = iio_priv(indio_dev);
	u8 buf[AD7173_RESET_LENGTH];
	unsigned int id;
	int ret;

...

> +	return vref / (MICRO/MILLI);

What does the denominator mean and why you can't simply use MILL?

...

> +			if (ch->cfg.bipolar)
> +				/* (1<<31) is UB for a 32bit channel */
> +				*val = (chan->scan_type.realbits == 32) ?
> +					INT_MIN :
> +					-(1 << (chan->scan_type.realbits - 1));

So, what's the issue to use BIT() which has no such issue with UB?

> +			else
> +				*val = 0;

...

> +		*val = st->info->sinc5_data_rates[reg] / (MICRO/MILLI);
> +		*val2 = (st->info->sinc5_data_rates[reg] % MILLI) * (MICRO/MILLI);

Same Q about denominator.

...

> +	case IIO_CHAN_INFO_SAMP_FREQ:
> +		freq = val * MILLI + val2 / MILLI;

> +

Unneeded blank line.

> +		for (i = 0; i < st->info->num_sinc5_data_rates - 1; i++) {
> +			if (freq >= st->info->sinc5_data_rates[i])
> +				break;
> +		}
> +
> +		cfg = &st->channels[chan->address].cfg;
> +		cfg->odr = i;
> +
> +		if (!cfg->live)
> +			break;
> +
> +		ret = ad_sd_read_reg(&st->sd, AD7173_REG_FILTER(cfg->cfg_slot), 2, &reg);
> +		if (ret)
> +			break;
> +		reg &= ~AD7173_FILTER_ODR0_MASK;
> +		reg |= FIELD_PREP(AD7173_FILTER_ODR0_MASK, i);
> +		ret = ad_sd_write_reg(&st->sd, AD7173_REG_FILTER(cfg->cfg_slot), 2, reg);
> +		break;

...

> +static int ad7173_update_scan_mode(struct iio_dev *indio_dev,
> +				   const unsigned long *scan_mask)
> +{
> +	struct ad7173_state *st = iio_priv(indio_dev);

> +	int i, ret = 0;

Use the 0 directly...

> +
> +	for (i = 0; i < indio_dev->num_channels; i++) {
> +		if (test_bit(i, scan_mask))
> +			ret = ad7173_set_channel(&st->sd, i);
> +		else
> +			ret = ad_sd_write_reg(&st->sd, AD7173_REG_CH(i), 2, 0);
> +
> +		if (ret < 0)
> +			return ret;
> +	}
> +
> +	return ret;

...here.

> +}

> +	chan_arr = devm_kcalloc(dev, sizeof(*chan_arr), num_channels,
> +				GFP_KERNEL);

One line.

> +	if (!chan_arr)
> +		return -ENOMEM;

...

> +		if (fwnode_property_read_u32(child, "adi,reference-select", &ref_sel))
> +			ref_sel = AD7173_SETUP_REF_SEL_INT_REF;

if is redundant.

		ref_sel = AD7173_SETUP_REF_SEL_INT_REF;
		fwnode_property_read_u32(child, "adi,reference-select", &ref_sel);
Ceclan, Dumitru Nov. 20, 2023, 3:55 p.m. UTC | #2
On 11/20/23 15:00, Andy Shevchenko wrote:
> On Thu, Nov 16, 2023 at 03:46:55PM +0200, mitrutzceclan wrote:
>> +struct ad7173_channel_config {
>> +	bool live;
>> +	u8 cfg_slot;
>> +	/* Following fields are used to compare equality. Bipolar must be first */
>> +	bool bipolar;
>> +	bool input_buf;
>> +	u8 odr;
>> +	u8 ref_sel;
> 
> If you group better by types, it might save a few bytes on the architectures /
> compilers where bool != byte.
>
Grouping by type will result in not being able to use memcmp() for
comparing configs. But then there is the issue that I was under the
assumption that bool=byte. If that is not the case, the config equality
check might be comparing padding bytes.

In this case what do you suggest:
- using the packed attribute
- using only u8
- drop memcmp, manually compare fields

...

>> +	cmp_size = sizeof(*cfg) - offset;
> 
> sizeof_field() from the above mentioned header?

This computes the size of multiple fields, following cfg_slot. Better to
group the fields that need to be compared into another struct then use
sizeof_field()?

...

> 
>> +	return vref / (MICRO/MILLI);
> 
> What does the denominator mean and why you can't simply use MILL?
>

Original vref values are in micro, I considered that it was adequate to
represent the conversion from MICRO to MILLI as a fraction.

>> +		*val = st->info->sinc5_data_rates[reg] / (MICRO/MILLI);
>> +		*val2 = (st->info->sinc5_data_rates[reg] % MILLI) * (MICRO/MILLI);
> 
> Same Q about denominator.
> 
Here, a misunderstanding on my part of a suggestion from Jonathan in V2,
will be removed.
Andy Shevchenko Nov. 20, 2023, 4:21 p.m. UTC | #3
On Mon, Nov 20, 2023 at 05:55:12PM +0200, Ceclan Dumitru wrote:
> On 11/20/23 15:00, Andy Shevchenko wrote:
> > On Thu, Nov 16, 2023 at 03:46:55PM +0200, mitrutzceclan wrote:

...

> >> +struct ad7173_channel_config {
> >> +	bool live;
> >> +	u8 cfg_slot;
> >> +	/* Following fields are used to compare equality. Bipolar must be first */
> >> +	bool bipolar;
> >> +	bool input_buf;
> >> +	u8 odr;
> >> +	u8 ref_sel;
> > 
> > If you group better by types, it might save a few bytes on the architectures /
> > compilers where bool != byte.
> >
> Grouping by type will result in not being able to use memcmp() for
> comparing configs. But then there is the issue that I was under the
> assumption that bool=byte. If that is not the case, the config equality
> check might be comparing padding bytes.

It's most likely the case, BUT... it is not guaranteed by the C standard.

> In this case what do you suggest:
> - using the packed attribute
> - using only u8
> - drop memcmp, manually compare fields

Use struct_group() to show explicitly the group of members. If it's not an ABI
in any sense, then memcmp() is fine.

...

> >> +	cmp_size = sizeof(*cfg) - offset;
> > 
> > sizeof_field() from the above mentioned header?
> 
> This computes the size of multiple fields, following cfg_slot. Better to
> group the fields that need to be compared into another struct then use
> sizeof_field()?

See above.

...

> >> +	return vref / (MICRO/MILLI);
> > 
> > What does the denominator mean and why you can't simply use MILL?
> 
> Original vref values are in micro, I considered that it was adequate to
> represent the conversion from MICRO to MILLI as a fraction.
> 
> >> +		*val = st->info->sinc5_data_rates[reg] / (MICRO/MILLI);
> >> +		*val2 = (st->info->sinc5_data_rates[reg] % MILLI) * (MICRO/MILLI);
> > 
> > Same Q about denominator.
> > 
> Here, a misunderstanding on my part of a suggestion from Jonathan in V2,
> will be removed.

You need to clarify with him that.
Ceclan, Dumitru Nov. 21, 2023, 5:17 p.m. UTC | #4
On 11/20/23 18:21, Andy Shevchenko wrote:> On Mon, Nov 20, 2023 at
05:55:12PM +0200, Ceclan Dumitru wrote:
>> On 11/20/23 15:00, Andy Shevchenko wrote:
>>> On Thu, Nov 16, 2023 at 03:46:55PM +0200, mitrutzceclan wrote:

> 
> Use struct_group() to show explicitly the group of members. If it's not an ABI in any sense, then memcmp() is fine.
> 

Alright

>>>> +	return vref / (MICRO/MILLI);
>>>
>>> What does the denominator mean and why you can't simply use MILL?
>>
>> Original vref values are in micro, I considered that it was adequate 
>> to represent the conversion from MICRO to MILLI as a fraction.
>>
>>>> +		*val = st->info->sinc5_data_rates[reg] / (MICRO/MILLI);
>>>> +		*val2 = (st->info->sinc5_data_rates[reg] % MILLI) * 
>>>> +(MICRO/MILLI);
>>>
>>> Same Q about denominator.
>>>
>> Here, a misunderstanding on my part of a suggestion from Jonathan in 
>> V2, will be removed.
> 
> You need to clarify with him that.
> 
My misunderstanding was that he only referred to the multiplication, not
the denominator. *val has a conversion from MILLI to no metric prefix
while *val2 converts from MILLI to MICRO.
diff mbox series

Patch

diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 35f9867da12c..c0d522ef1db5 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -54,6 +54,19 @@  config AD7124
 	  To compile this driver as a module, choose M here: the module will be
 	  called ad7124.
 
+config AD7173
+	tristate "Analog Devices AD7173 driver"
+	depends on SPI_MASTER
+	select AD_SIGMA_DELTA
+	select GPIO_REGMAP if GPIOLIB
+	select REGMAP_SPI if GPIOLIB
+	help
+	  Say yes here to build support for Analog Devices AD7173 and similar ADC
+	  (currently supported: AD7172-2, AD7173-8, AD7175-2, AD7176-2).
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called ad7173.
+
 config AD7192
 	tristate "Analog Devices AD7190 AD7192 AD7193 AD7195 ADC driver"
 	depends on SPI
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index bee11d442af4..9f1f8f263340 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -9,6 +9,7 @@  obj-$(CONFIG_AD_SIGMA_DELTA) += ad_sigma_delta.o
 obj-$(CONFIG_AD4130) += ad4130.o
 obj-$(CONFIG_AD7091R5) += ad7091r5.o ad7091r-base.o
 obj-$(CONFIG_AD7124) += ad7124.o
+obj-$(CONFIG_AD7173) += ad7173.o
 obj-$(CONFIG_AD7192) += ad7192.o
 obj-$(CONFIG_AD7266) += ad7266.o
 obj-$(CONFIG_AD7280) += ad7280a.o
diff --git a/drivers/iio/adc/ad7173.c b/drivers/iio/adc/ad7173.c
new file mode 100644
index 000000000000..cbd3ba7ceab8
--- /dev/null
+++ b/drivers/iio/adc/ad7173.c
@@ -0,0 +1,936 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * AD7172-2/AD7173-8/AD7175-2/AD7176-2 SPI ADC driver
+ * Copyright (C) 2015, 2023 Analog Devices, Inc.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bitmap.h>
+#include <linux/bits.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/gpio/driver.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/gpio/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+#include <linux/units.h>
+
+#include <linux/iio/buffer.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+
+#include <linux/iio/adc/ad_sigma_delta.h>
+
+#define AD7173_REG_COMMS		0x00
+#define AD7173_REG_ADC_MODE		0x01
+#define AD7173_REG_INTERFACE_MODE	0x02
+#define AD7173_REG_CRC			0x03
+#define AD7173_REG_DATA			0x04
+#define AD7173_REG_GPIO			0x06
+#define AD7173_REG_ID			0x07
+#define AD7173_REG_CH(x)		(0x10 + (x))
+#define AD7173_REG_SETUP(x)		(0x20 + (x))
+#define AD7173_REG_FILTER(x)		(0x28 + (x))
+#define AD7173_REG_OFFSET(x)		(0x30 + (x))
+#define AD7173_REG_GAIN(x)		(0x38 + (x))
+
+#define AD7173_RESET_LENGTH		BITS_TO_BYTES(64)
+
+#define AD7173_CH_ENABLE		BIT(15)
+#define AD7173_CH_SETUP_SEL_MASK	GENMASK(14, 12)
+#define AD7173_CH_SETUP_AINPOS_MASK	GENMASK(9, 5)
+#define AD7173_CH_SETUP_AINNEG_MASK	GENMASK(4, 0)
+
+#define AD7173_CH_ADDRESS(pos, neg) \
+	(FIELD_PREP(AD7173_CH_SETUP_AINPOS_MASK, pos) |\
+	 FIELD_PREP(AD7173_CH_SETUP_AINNEG_MASK, neg))
+#define AD7173_AIN_TEMP_POS	17
+#define AD7173_AIN_TEMP_NEG	18
+
+#define AD7172_ID			0x00d0
+#define AD7173_ID			0x30d0
+#define AD7175_ID			0x0cd0
+#define AD7176_ID			0x0c90
+#define AD7173_ID_MASK			GENMASK(15, 4)
+
+#define AD7173_ADC_MODE_REF_EN		BIT(15)
+#define AD7173_ADC_MODE_SING_CYC	BIT(13)
+#define AD7173_ADC_MODE_MODE_MASK	GENMASK(6, 4)
+#define AD7173_ADC_MODE_CLOCKSEL_MASK	GENMASK(3, 2)
+
+#define AD7173_GPIO_PDSW	BIT(14)
+#define AD7173_GPIO_OP_EN2_3	BIT(13)
+#define AD7173_GPIO_MUX_IO	BIT(12)
+#define AD7173_GPIO_SYNC_EN	BIT(11)
+#define AD7173_GPIO_ERR_EN	BIT(10)
+#define AD7173_GPIO_ERR_DAT	BIT(9)
+#define AD7173_GPIO_GP_DATA3	BIT(7)
+#define AD7173_GPIO_GP_DATA2	BIT(6)
+#define AD7173_GPIO_IP_EN1	BIT(5)
+#define AD7173_GPIO_IP_EN0	BIT(4)
+#define AD7173_GPIO_OP_EN1	BIT(3)
+#define AD7173_GPIO_OP_EN0	BIT(2)
+#define AD7173_GPIO_GP_DATA1	BIT(1)
+#define AD7173_GPIO_GP_DATA0	BIT(0)
+
+#define AD7173_GPO12_DATA(x)	BIT(x)
+#define AD7173_GPO23_DATA(x)	BIT(x + 4)
+#define AD7173_GPO_DATA(x)	(x < 2 ? AD7173_GPO12_DATA(x) : AD7173_GPO23_DATA(x))
+
+#define AD7173_INTERFACE_DATA_STAT	BIT(6)
+#define AD7173_INTERFACE_DATA_STAT_EN(x)\
+	FIELD_PREP(AD7173_INTERFACE_DATA_STAT, x)
+
+#define AD7173_SETUP_BIPOLAR		BIT(12)
+#define AD7173_SETUP_AREF_BUF_MASK	GENMASK(11, 10)
+#define AD7173_SETUP_AIN_BUF_MASK	GENMASK(9, 8)
+
+#define AD7173_SETUP_REF_SEL_MASK	GENMASK(5, 4)
+#define AD7173_SETUP_REF_SEL_AVDD1_AVSS	0x3
+#define AD7173_SETUP_REF_SEL_INT_REF	0x2
+#define AD7173_SETUP_REF_SEL_EXT_REF2	0x1
+#define AD7173_SETUP_REF_SEL_EXT_REF	0x0
+#define AD7173_VOLTAGE_INT_REF_MICROV	2500000
+
+#define AD7173_FILTER_ODR0_MASK		GENMASK(5, 0)
+#define AD7173_MAX_CONFIGS		8
+
+enum ad7173_ids {
+	ID_AD7172_2,
+	ID_AD7173_8,
+	ID_AD7175_2,
+	ID_AD7176_2,
+};
+
+struct ad7173_device_info {
+	char *name;
+	unsigned int id;
+	unsigned int num_inputs;
+	unsigned int num_configs;
+	unsigned int num_channels;
+	unsigned char num_gpios;
+	bool has_temp;
+	unsigned int clock;
+
+	const unsigned int *sinc5_data_rates;
+	unsigned int num_sinc5_data_rates;
+};
+
+struct ad7173_channel_config {
+	bool live;
+	u8 cfg_slot;
+	/* Following fields are used to compare equality. Bipolar must be first */
+	bool bipolar;
+	bool input_buf;
+	u8 odr;
+	u8 ref_sel;
+};
+
+struct ad7173_channel {
+	unsigned int chan_reg;
+	unsigned int ain;
+	struct ad7173_channel_config cfg;
+};
+
+struct ad7173_state {
+	const struct ad7173_device_info *info;
+	struct ad_sigma_delta sd;
+	struct ad7173_channel *channels;
+	struct regulator_bulk_data regulators[3];
+	unsigned int adc_mode;
+	unsigned int interface_mode;
+	unsigned int num_channels;
+	DECLARE_BITMAP(cfg_slots_status, AD7173_MAX_CONFIGS); /* slots usage status */
+	unsigned long long config_usage_counter;
+	unsigned long long *config_cnts;
+#if IS_ENABLED(CONFIG_GPIOLIB)
+	struct regmap *reg_gpiocon_regmap;
+	struct gpio_regmap *gpio_regmap;
+#endif
+};
+
+static const unsigned int ad7173_sinc5_data_rates[] = {
+	6211000, 6211000, 6211000, 6211000, 6211000, 6211000, 5181000, 4444000,
+	3115000, 2597000, 1007000, 503800,  381000,  200300,  100500,  59520,
+	49680,	 20010,	  16333,   10000,   5000,    2500,    1250,
+};
+
+static const unsigned int ad7175_sinc5_data_rates[] = {
+	50000000, 41667000, 31250000, 27778000, 20833000, 17857000, 12500000,
+	10000000, 5000000,  2500000,  1000000,	500000,	  397500,   200000,
+	100000,	  59920,    49960,    20000,	16666,	  10000,    5000,
+};
+
+static const struct ad7173_device_info ad7173_device_info[] = {
+	[ID_AD7172_2] = {
+		.name = "ad7172-2",
+		.id = AD7172_ID,
+		.num_inputs = 5,
+		.num_channels = 4,
+		.num_configs = 4,
+		.num_gpios = 2,
+		.has_temp = true,
+		.clock = 2 * HZ_PER_MHZ,
+		.sinc5_data_rates = ad7173_sinc5_data_rates,
+		.num_sinc5_data_rates = ARRAY_SIZE(ad7173_sinc5_data_rates),
+	},
+	[ID_AD7173_8] = {
+		.name = "ad7173-8",
+		.id = AD7173_ID,
+		.num_inputs = 17,
+		.num_channels = 16,
+		.num_configs = 8,
+		.num_gpios = 4,
+		.has_temp = true,
+		.clock = 2 * HZ_PER_MHZ,
+		.sinc5_data_rates = ad7173_sinc5_data_rates,
+		.num_sinc5_data_rates = ARRAY_SIZE(ad7173_sinc5_data_rates),
+	},
+	[ID_AD7175_2] = {
+		.name = "ad7175-2",
+		.id = AD7175_ID,
+		.num_inputs = 5,
+		.num_channels = 4,
+		.num_configs = 4,
+		.num_gpios = 2,
+		.has_temp = true,
+		.clock = 16 * HZ_PER_MHZ,
+		.sinc5_data_rates = ad7175_sinc5_data_rates,
+		.num_sinc5_data_rates = ARRAY_SIZE(ad7175_sinc5_data_rates),
+	},
+	[ID_AD7176_2] = {
+		.name = "ad7176-2",
+		.id = AD7176_ID,
+		.num_inputs = 5,
+		.num_channels = 4,
+		.num_configs = 4,
+		.num_gpios = 2,
+		.has_temp = false,
+		.clock = 16 * HZ_PER_MHZ,
+		.sinc5_data_rates = ad7175_sinc5_data_rates,
+		.num_sinc5_data_rates = ARRAY_SIZE(ad7175_sinc5_data_rates),
+	},
+};
+
+#if IS_ENABLED(CONFIG_GPIOLIB)
+
+static const struct regmap_range ad7173_range_gpio[] = {
+	regmap_reg_range(AD7173_REG_GPIO, AD7173_REG_GPIO),
+};
+
+static const struct regmap_access_table ad7173_access_table = {
+	.yes_ranges = ad7173_range_gpio,
+	.n_yes_ranges = ARRAY_SIZE(ad7173_range_gpio),
+};
+
+static const struct regmap_config ad7173_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 16,
+	.rd_table = &ad7173_access_table,
+	.wr_table = &ad7173_access_table,
+	.read_flag_mask = BIT(6),
+};
+
+static int ad7173_mask_xlate(struct gpio_regmap *gpio, unsigned int base,
+			     unsigned int offset, unsigned int *reg,
+			     unsigned int *mask)
+{
+	*mask = AD7173_GPO_DATA(offset);
+	*reg = base;
+	return 0;
+}
+
+static void ad7173_gpio_disable(void *data)
+{
+	struct ad7173_state *st = data;
+	unsigned int mask;
+
+	mask = AD7173_GPIO_OP_EN0 | AD7173_GPIO_OP_EN1 | AD7173_GPIO_OP_EN2_3;
+	regmap_update_bits(st->reg_gpiocon_regmap, AD7173_REG_GPIO, mask, ~mask);
+}
+
+static int ad7173_gpio_init(struct ad7173_state *st)
+{
+	struct gpio_regmap_config gpio_regmap = {};
+	struct device *dev = &st->sd.spi->dev;
+	unsigned int mask;
+	int ret;
+
+	st->reg_gpiocon_regmap = devm_regmap_init_spi(st->sd.spi, &ad7173_regmap_config);
+	if (IS_ERR(st->reg_gpiocon_regmap)) {
+		return dev_err_probe(dev, PTR_ERR(st->reg_gpiocon_regmap),
+				     "Unable to init regmap\n");
+	}
+
+	mask = AD7173_GPIO_OP_EN0 | AD7173_GPIO_OP_EN1 | AD7173_GPIO_OP_EN2_3;
+	regmap_update_bits(st->reg_gpiocon_regmap, AD7173_REG_GPIO, mask, mask);
+
+	ret = devm_add_action_or_reset(dev, ad7173_gpio_disable, st);
+	if (ret)
+		return ret;
+
+	gpio_regmap.parent = dev;
+	gpio_regmap.regmap = st->reg_gpiocon_regmap;
+	gpio_regmap.ngpio = st->info->num_gpios;
+	gpio_regmap.reg_set_base = AD7173_REG_GPIO;
+	gpio_regmap.reg_mask_xlate = ad7173_mask_xlate;
+
+	st->gpio_regmap = devm_gpio_regmap_register(dev, &gpio_regmap);
+	if (IS_ERR(st->gpio_regmap)) {
+		return dev_err_probe(dev, PTR_ERR(st->gpio_regmap),
+				     "Unable to init gpio-regmap\n");
+	}
+
+	return 0;
+}
+
+#endif /* CONFIG_GPIOLIB */
+
+static struct ad7173_state *ad_sigma_delta_to_ad7173(struct ad_sigma_delta *sd)
+{
+	return container_of(sd, struct ad7173_state, sd);
+}
+
+static void ad7173_reset_usage_cnts(struct ad7173_state *st)
+{
+	memset64(st->config_cnts, 0, st->info->num_configs);
+	st->config_usage_counter = 0;
+}
+
+static struct ad7173_channel_config *ad7173_find_live_config
+	(struct ad7173_state *st, struct ad7173_channel_config *cfg)
+{
+	struct ad7173_channel_config *cfg_aux;
+	ptrdiff_t cmp_size, offset;
+	int i;
+
+	offset = offsetof(struct ad7173_channel_config, cfg_slot) +
+		 sizeof(cfg->cfg_slot);
+	cmp_size = sizeof(*cfg) - offset;
+
+	for (i = 0; i < st->num_channels; i++) {
+		cfg_aux = &st->channels[i].cfg;
+
+		if (cfg_aux->live && !memcmp(&cfg->bipolar, &cfg_aux->bipolar,
+					     cmp_size))
+			return cfg_aux;
+	}
+	return NULL;
+}
+
+static int ad7173_free_config_slot_lru(struct ad7173_state *st)
+{
+	int i, lru_position = 0;
+
+	for (i = 1; i < st->info->num_configs; i++)
+		if (st->config_cnts[i] < st->config_cnts[lru_position])
+			lru_position = i;
+
+	for (i = 0; i < st->num_channels; i++)
+		if (st->channels[i].cfg.cfg_slot == lru_position)
+			st->channels[i].cfg.live = false;
+
+	clear_bit(lru_position, st->cfg_slots_status);
+	return lru_position;
+}
+
+static int ad7173_load_config(struct ad7173_state *st,
+			      struct ad7173_channel_config *cfg)
+{
+	unsigned int config;
+	int free_cfg_slot, ret;
+
+	free_cfg_slot = find_first_zero_bit(st->cfg_slots_status,
+					    st->info->num_configs);
+	if (free_cfg_slot == st->info->num_configs)
+		free_cfg_slot = ad7173_free_config_slot_lru(st);
+
+	set_bit(free_cfg_slot, st->cfg_slots_status);
+	cfg->cfg_slot = free_cfg_slot;
+
+	config = FIELD_PREP(AD7173_SETUP_REF_SEL_MASK, cfg->ref_sel);
+
+	if (cfg->bipolar)
+		config |= AD7173_SETUP_BIPOLAR;
+
+	if (cfg->input_buf)
+		config |= AD7173_SETUP_AIN_BUF_MASK;
+
+	ret = ad_sd_write_reg(&st->sd, AD7173_REG_SETUP(free_cfg_slot), 2, config);
+	if (ret)
+		return ret;
+
+	return ad_sd_write_reg(&st->sd, AD7173_REG_FILTER(free_cfg_slot), 2,
+			       AD7173_FILTER_ODR0_MASK & cfg->odr);
+}
+
+static int ad7173_config_channel(struct ad7173_state *st, int addr)
+{
+	struct ad7173_channel_config *cfg = &st->channels[addr].cfg;
+	struct ad7173_channel_config *live_cfg;
+	int ret;
+
+	if (!cfg->live) {
+		live_cfg = ad7173_find_live_config(st, cfg);
+		if (live_cfg) {
+			cfg->cfg_slot = live_cfg->cfg_slot;
+		} else {
+			ret = ad7173_load_config(st, cfg);
+			if (ret)
+				return ret;
+			cfg->live = true;
+		}
+	}
+
+	if (st->config_usage_counter == U64_MAX)
+		ad7173_reset_usage_cnts(st);
+
+	st->config_usage_counter++;
+	st->config_cnts[cfg->cfg_slot] = st->config_usage_counter;
+
+	return 0;
+}
+
+static int ad7173_set_channel(struct ad_sigma_delta *sd, unsigned int channel)
+{
+	struct ad7173_state *st = ad_sigma_delta_to_ad7173(sd);
+	unsigned int val;
+	int ret;
+
+	ret = ad7173_config_channel(st, channel);
+	if (ret)
+		return ret;
+
+	val = AD7173_CH_ENABLE |
+	      FIELD_PREP(AD7173_CH_SETUP_SEL_MASK, st->channels[channel].cfg.cfg_slot) |
+	      st->channels[channel].ain;
+
+	return ad_sd_write_reg(&st->sd, AD7173_REG_CH(channel), 2, val);
+}
+
+static int ad7173_set_mode(struct ad_sigma_delta *sd,
+			   enum ad_sigma_delta_mode mode)
+{
+	struct ad7173_state *st = ad_sigma_delta_to_ad7173(sd);
+
+	st->adc_mode &= ~AD7173_ADC_MODE_MODE_MASK;
+	st->adc_mode |= FIELD_PREP(AD7173_ADC_MODE_MODE_MASK, mode);
+
+	return ad_sd_write_reg(&st->sd, AD7173_REG_ADC_MODE, 2, st->adc_mode);
+}
+
+static int ad7173_append_status(struct ad_sigma_delta *sd, bool append)
+{
+	struct ad7173_state *st = ad_sigma_delta_to_ad7173(sd);
+	unsigned int interface_mode = st->interface_mode;
+	int ret;
+
+	interface_mode |= AD7173_INTERFACE_DATA_STAT_EN(append);
+	ret = ad_sd_write_reg(&st->sd, AD7173_REG_INTERFACE_MODE, 2, interface_mode);
+	if (ret)
+		return ret;
+
+	st->interface_mode = interface_mode;
+
+	return 0;
+}
+
+static int ad7173_disable_all(struct ad_sigma_delta *sd)
+{
+	struct ad7173_state *st = ad_sigma_delta_to_ad7173(sd);
+	int ret;
+	int i;
+
+	for (i = 0; i < st->num_channels; i++) {
+		ret = ad_sd_write_reg(sd, AD7173_REG_CH(i), 2, 0);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static struct ad_sigma_delta_info ad7173_sigma_delta_info = {
+	.set_channel = ad7173_set_channel,
+	.append_status = ad7173_append_status,
+	.disable_all = ad7173_disable_all,
+	.set_mode = ad7173_set_mode,
+	.has_registers = true,
+	.addr_shift = 0,
+	.read_mask = BIT(6),
+	.status_ch_mask = GENMASK(3, 0),
+	.data_reg = AD7173_REG_DATA,
+	.irq_flags = IRQF_TRIGGER_FALLING,
+};
+
+static int ad7173_setup(struct iio_dev *indio_dev)
+{
+	struct ad7173_state *st = iio_priv(indio_dev);
+	unsigned int id;
+	u8 buf[AD7173_RESET_LENGTH];
+	int ret;
+
+	/* reset the serial interface */
+	memset(buf, 0xff, AD7173_RESET_LENGTH);
+	ret = spi_write_then_read(st->sd.spi, buf, sizeof(buf), NULL, 0);
+	if (ret < 0)
+		return ret;
+
+	/* datasheet recommends a delay of at least 500us after reset */
+	fsleep(500);
+
+	ret = ad_sd_read_reg(&st->sd, AD7173_REG_ID, 2, &id);
+	if (ret)
+		return ret;
+
+	id &= AD7173_ID_MASK;
+	if (id != st->info->id)
+		dev_warn(&st->sd.spi->dev,
+			 "Unexpected device id: %x, expected: %x\n",
+			 id, st->info->id);
+
+	st->adc_mode |= AD7173_ADC_MODE_SING_CYC;
+	st->interface_mode = 0x0;
+
+	st->config_usage_counter = 0;
+	st->config_cnts = devm_kcalloc(indio_dev->dev.parent,
+				       st->info->num_configs, sizeof(u64),
+				       GFP_KERNEL);
+	if (!st->config_cnts)
+		return -ENOMEM;
+
+	/* All channels are enabled by default after a reset */
+	return ad7173_disable_all(&st->sd);
+}
+
+static unsigned int ad7173_get_ref_voltage_milli(struct ad7173_state *st,
+						 u8 reference_select)
+{
+	int vref;
+
+	switch (reference_select) {
+	case AD7173_SETUP_REF_SEL_EXT_REF:
+		vref = regulator_get_voltage(st->regulators[0].consumer);
+		break;
+
+	case AD7173_SETUP_REF_SEL_EXT_REF2:
+		vref = regulator_get_voltage(st->regulators[1].consumer);
+		break;
+
+	case AD7173_SETUP_REF_SEL_INT_REF:
+		vref = AD7173_VOLTAGE_INT_REF_MICROV;
+		break;
+
+	case AD7173_SETUP_REF_SEL_AVDD1_AVSS:
+		vref = regulator_get_voltage(st->regulators[2].consumer);
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	if (vref < 0)
+		return vref;
+
+	return vref / (MICRO/MILLI);
+}
+
+static int ad7173_read_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan,
+			   int *val, int *val2, long info)
+{
+	struct ad7173_state *st = iio_priv(indio_dev);
+	struct ad7173_channel *ch = &st->channels[chan->address];
+	unsigned int reg;
+	int ret;
+
+	switch (info) {
+	case IIO_CHAN_INFO_RAW:
+		ret = ad_sigma_delta_single_conversion(indio_dev, chan, val);
+		if (ret < 0)
+			return ret;
+
+		/* disable channel after single conversion */
+		ret = ad_sd_write_reg(&st->sd, AD7173_REG_CH(chan->address), 2, 0);
+		if (ret < 0)
+			return ret;
+
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		if (chan->type == IIO_TEMP) {
+			*val = 250000000;
+			*val2 = 800273203; /* (2^24 * 477) / 10 */
+			return IIO_VAL_FRACTIONAL;
+		} else {
+			*val = ad7173_get_ref_voltage_milli(st, ch->cfg.ref_sel);
+			*val2 = chan->scan_type.realbits - !!(ch->cfg.bipolar);
+			return IIO_VAL_FRACTIONAL_LOG2;
+		}
+	case IIO_CHAN_INFO_OFFSET:
+		if (chan->type == IIO_TEMP) {
+			*val = -874379;
+		} else {
+			if (ch->cfg.bipolar)
+				/* (1<<31) is UB for a 32bit channel */
+				*val = (chan->scan_type.realbits == 32) ?
+					INT_MIN :
+					-(1 << (chan->scan_type.realbits - 1));
+			else
+				*val = 0;
+		}
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		reg = st->channels[chan->address].cfg.odr;
+
+		*val = st->info->sinc5_data_rates[reg] / (MICRO/MILLI);
+		*val2 = (st->info->sinc5_data_rates[reg] % MILLI) * (MICRO/MILLI);
+
+		return IIO_VAL_INT_PLUS_MICRO;
+	}
+	return -EINVAL;
+}
+
+static int ad7173_write_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int val, int val2, long info)
+{
+	struct ad7173_state *st = iio_priv(indio_dev);
+	struct ad7173_channel_config *cfg;
+	unsigned int freq, i, reg;
+	int ret;
+
+	ret = iio_device_claim_direct_mode(indio_dev);
+	if (ret)
+		return ret;
+
+	switch (info) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		freq = val * MILLI + val2 / MILLI;
+
+		for (i = 0; i < st->info->num_sinc5_data_rates - 1; i++) {
+			if (freq >= st->info->sinc5_data_rates[i])
+				break;
+		}
+
+		cfg = &st->channels[chan->address].cfg;
+		cfg->odr = i;
+
+		if (!cfg->live)
+			break;
+
+		ret = ad_sd_read_reg(&st->sd, AD7173_REG_FILTER(cfg->cfg_slot), 2, &reg);
+		if (ret)
+			break;
+		reg &= ~AD7173_FILTER_ODR0_MASK;
+		reg |= FIELD_PREP(AD7173_FILTER_ODR0_MASK, i);
+		ret = ad_sd_write_reg(&st->sd, AD7173_REG_FILTER(cfg->cfg_slot), 2, reg);
+		break;
+
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	iio_device_release_direct_mode(indio_dev);
+	return ret;
+}
+
+static int ad7173_update_scan_mode(struct iio_dev *indio_dev,
+				   const unsigned long *scan_mask)
+{
+	struct ad7173_state *st = iio_priv(indio_dev);
+	int i, ret = 0;
+
+	for (i = 0; i < indio_dev->num_channels; i++) {
+		if (test_bit(i, scan_mask))
+			ret = ad7173_set_channel(&st->sd, i);
+		else
+			ret = ad_sd_write_reg(&st->sd, AD7173_REG_CH(i), 2, 0);
+
+		if (ret < 0)
+			return ret;
+	}
+
+	return ret;
+}
+
+static int ad7173_debug(struct iio_dev *indio_dev, unsigned int reg,
+			unsigned int writeval, unsigned int *readval)
+{
+	struct ad7173_state *st = iio_priv(indio_dev);
+	u8 reg_size;
+
+	if (reg == 0)
+		reg_size = 1;
+	else if (reg == AD7173_REG_CRC || reg == AD7173_REG_DATA ||
+		 reg >= AD7173_REG_OFFSET(0))
+		reg_size = 3;
+	else
+		reg_size = 2;
+
+	if (readval)
+		return ad_sd_read_reg(&st->sd, reg, reg_size, readval);
+
+	return ad_sd_write_reg(&st->sd, reg, reg_size, writeval);
+}
+
+static const struct iio_info ad7173_info = {
+	.read_raw = &ad7173_read_raw,
+	.write_raw = &ad7173_write_raw,
+	.debugfs_reg_access = &ad7173_debug,
+	.validate_trigger = ad_sd_validate_trigger,
+	.update_scan_mode = ad7173_update_scan_mode,
+};
+
+static const struct iio_chan_spec ad7173_channel_template = {
+	.type = IIO_VOLTAGE,
+	.indexed = 1,
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+		BIT(IIO_CHAN_INFO_SCALE),
+	.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+	.scan_type = {
+		.sign = 'u',
+		.realbits = 24,
+		.storagebits = 32,
+		.endianness = IIO_BE,
+	},
+};
+
+static const struct iio_chan_spec ad7173_temp_iio_channel_template = {
+	.type = IIO_TEMP,
+	.indexed = 1,
+	.channel = AD7173_AIN_TEMP_POS,
+	.channel2 = AD7173_AIN_TEMP_NEG,
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+		BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_OFFSET),
+	.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+	.scan_type = {
+		.sign = 'u',
+		.realbits = 24,
+		.storagebits = 32,
+		.endianness = IIO_BE,
+	},
+};
+
+static void ad7173_disable_regulators(void *data)
+{
+	struct ad7173_state *st = data;
+
+	regulator_bulk_disable(ARRAY_SIZE(st->regulators), st->regulators);
+}
+
+static int ad7173_fw_parse_channel_config(struct iio_dev *indio_dev)
+{
+	struct ad7173_state *st = iio_priv(indio_dev);
+	struct ad7173_channel *channels_st_priv_arr, *chan_st_priv;
+	struct fwnode_handle *child;
+	struct device *dev = indio_dev->dev.parent;
+	struct iio_chan_spec *chan_arr, *chan;
+	unsigned int num_channels;
+	unsigned int ain[2], chan_index = 0;
+	u32 ref_sel;
+	int ret;
+
+	st->regulators[0].supply = "refin";
+	st->regulators[1].supply = "refin2";
+	st->regulators[2].supply = "avdd";
+
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(st->regulators),
+				      st->regulators);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to get regulators\n");
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(st->regulators), st->regulators);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to enable regulators\n");
+
+	ret = devm_add_action_or_reset(dev, ad7173_disable_regulators, st);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "Failed to add regulators disable action\n");
+
+	num_channels = device_get_child_node_count(dev);
+
+	if (st->info->has_temp)
+		num_channels++;
+
+	if (num_channels == 0)
+		return 0;
+	st->num_channels = num_channels;
+
+	chan_arr = devm_kcalloc(dev, sizeof(*chan_arr), num_channels,
+				GFP_KERNEL);
+	if (!chan_arr)
+		return -ENOMEM;
+
+	channels_st_priv_arr = devm_kcalloc(dev, num_channels,
+					    sizeof(*channels_st_priv_arr),
+					    GFP_KERNEL);
+	if (!channels_st_priv_arr)
+		return -ENOMEM;
+
+	indio_dev->channels = chan_arr;
+	indio_dev->num_channels = num_channels;
+	st->channels = channels_st_priv_arr;
+
+	if (st->info->has_temp) {
+		chan_arr[chan_index] = ad7173_temp_iio_channel_template;
+		chan_st_priv = &channels_st_priv_arr[chan_index];
+		chan_st_priv->ain =
+			AD7173_CH_ADDRESS(chan_arr[chan_index].channel, chan_arr[chan_index].channel2);
+		chan_st_priv->cfg.bipolar = false;
+		chan_st_priv->cfg.input_buf = true;
+		chan_st_priv->cfg.ref_sel = AD7173_SETUP_REF_SEL_INT_REF;
+		st->adc_mode |= AD7173_ADC_MODE_REF_EN;
+
+		chan_index++;
+	}
+
+	device_for_each_child_node(dev, child) {
+		chan = &chan_arr[chan_index];
+		chan_st_priv = &channels_st_priv_arr[chan_index];
+		ret = fwnode_property_read_u32_array(child, "diff-channels",
+						     ain, ARRAY_SIZE(ain));
+		if (ret) {
+			fwnode_handle_put(child);
+			return ret;
+		}
+
+		if (ain[0] >= st->info->num_inputs ||
+		    ain[1] >= st->info->num_inputs) {
+			fwnode_handle_put(child);
+			return dev_err_probe(dev, -EINVAL,
+				"Input pin number out of range for pair (%d %d).", ain[0], ain[1]);
+		}
+
+		if (fwnode_property_read_u32(child, "adi,reference-select", &ref_sel))
+			ref_sel = AD7173_SETUP_REF_SEL_INT_REF;
+		ret = ad7173_get_ref_voltage_milli(st, (u8)ref_sel);
+		if (ret < 0)
+			return dev_err_probe(dev, ret,
+					     "Cannot use reference %u", ref_sel);
+		if (ref_sel == AD7173_SETUP_REF_SEL_EXT_REF2 &&
+		    st->info->id != AD7173_ID)
+			return dev_err_probe(dev, -EINVAL, "External reference 2 is only available on ad7173-8");
+		if (ref_sel == AD7173_SETUP_REF_SEL_INT_REF)
+			st->adc_mode |= AD7173_ADC_MODE_REF_EN;
+		chan_st_priv->cfg.ref_sel = ref_sel;
+
+		*chan = ad7173_channel_template;
+		chan->address = chan_index;
+		chan->scan_index = chan_index;
+		chan->channel = ain[0];
+		chan->channel2 = ain[1];
+		chan->differential = true;
+
+		chan_st_priv->ain = AD7173_CH_ADDRESS(ain[0], ain[1]);
+		chan_st_priv->chan_reg = chan_index;
+		chan_st_priv->cfg.input_buf = true;
+		chan_st_priv->cfg.odr = 0;
+
+		chan_st_priv->cfg.bipolar = fwnode_property_read_bool(child, "bipolar");
+		if (chan_st_priv->cfg.bipolar)
+			chan->info_mask_separate |= BIT(IIO_CHAN_INFO_OFFSET);
+
+		chan_index++;
+	}
+
+	return 0;
+}
+
+static int ad7173_probe(struct spi_device *spi)
+{
+	struct ad7173_state *st;
+	struct iio_dev *indio_dev;
+	struct device *dev = &spi->dev;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*st));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	st = iio_priv(indio_dev);
+	st->info = spi_get_device_match_data(spi);
+	if (!st->info)
+		return -ENODEV;
+
+	indio_dev->name = st->info->name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->info = &ad7173_info;
+
+	spi->mode = SPI_MODE_3;
+
+	ad7173_sigma_delta_info.num_slots = st->info->num_configs;
+	ret = ad_sd_init(&st->sd, indio_dev, spi, &ad7173_sigma_delta_info);
+	if (ret)
+		return ret;
+
+	spi_set_drvdata(spi, indio_dev);
+
+	ret = ad7173_fw_parse_channel_config(indio_dev);
+	if (ret)
+		return ret;
+
+	ret = devm_ad_sd_setup_buffer_and_trigger(dev, indio_dev);
+	if (ret)
+		return ret;
+
+	ret = ad7173_setup(indio_dev);
+	if (ret)
+		return ret;
+
+	ret = devm_iio_device_register(dev, indio_dev);
+	if (ret)
+		return ret;
+
+	if (IS_ENABLED(CONFIG_GPIOLIB))
+		return ad7173_gpio_init(st);
+
+	return 0;
+}
+
+static const struct of_device_id ad7173_of_match[] = {
+	{ .compatible = "adi,ad7172-2",
+	  .data = &ad7173_device_info[ID_AD7172_2], },
+	{ .compatible = "adi,ad7173-8",
+	  .data = &ad7173_device_info[ID_AD7173_8], },
+	{ .compatible = "adi,ad7175-2",
+	  .data = &ad7173_device_info[ID_AD7175_2], },
+	{ .compatible = "adi,ad7176-2",
+	  .data = &ad7173_device_info[ID_AD7176_2], },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ad7173_of_match);
+
+static const struct spi_device_id ad7173_id_table[] = {
+	{ "ad7172-2", (kernel_ulong_t)&ad7173_device_info[ID_AD7172_2], },
+	{ "ad7173-8", (kernel_ulong_t)&ad7173_device_info[ID_AD7173_8], },
+	{ "ad7175-2", (kernel_ulong_t)&ad7173_device_info[ID_AD7175_2], },
+	{ "ad7176-2", (kernel_ulong_t)&ad7173_device_info[ID_AD7176_2], },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, ad7173_id_table);
+
+static struct spi_driver ad7173_driver = {
+	.driver = {
+		.name	= "ad7173",
+		.of_match_table = ad7173_of_match,
+	},
+	.probe		= ad7173_probe,
+	.id_table	= ad7173_id_table,
+};
+module_spi_driver(ad7173_driver);
+
+MODULE_AUTHOR("Lars-Peter Clausen <lars@metafo.de>");
+MODULE_AUTHOR("Dumitru Ceclan <dumitru.ceclan@analog.com>");
+MODULE_DESCRIPTION("Analog Devices AD7172/AD7173/AD7175/AD7176 ADC driver");
+MODULE_LICENSE("GPL");