| Message ID | 20231122182351.63214-2-linux.amoon@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v4,1/2] dt-bindings: usb: Add the binding example for the Genesys Logic GL3523 hub | expand |
On Wed, Nov 22, 2023 at 11:53:46PM +0530, Anand Moon wrote: > Add the binding example for the USB3.1 Genesys Logic GL3523 > integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed > hub. > > Onboard USB hub supports USB 3.x and USB 2.0 peer controllers. > which has a common reset pin and power supply. > peer-hub phandle each peer controller with proper gpio reset > and help each peer power on during initialization > and power off during suspend. > > Signed-off-by: Anand Moon <linux.amoon@gmail.com> > --- > v4: Fix the description of peer-hub and update the commit message. > Schematics of the Odroid N2+ > https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf > V3: fix the dt_binding_check error, added new example for Genesys GL3523 > v2: added Genesys GL3523 binding > v1: none > --- > .../bindings/usb/genesys,gl850g.yaml | 67 +++++++++++++++++-- > 1 file changed, 63 insertions(+), 4 deletions(-) > > diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > index ee08b9c3721f..bc3b3f4c8473 100644 > --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller > maintainers: > - Icenowy Zheng <uwu@icenowy.me> > > -allOf: > - - $ref: usb-device.yaml# > - > properties: > compatible: > enum: > @@ -27,12 +24,48 @@ properties: > > vdd-supply: > description: > - the regulator that provides 3.3V core power to the hub. > + phandle to the regulator that provides power to the hub. > + > + peer-hub: Should the property not be "peer-controller"? Your description refers to them as such. > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + onboard USB hub supports USB 3.x and USB 2.0 peer controllers. > + which has a common reset pin and power supply. > + peer-hub phandle each peer controller with proper gpio reset > + and help each peer power on during initialization > + and power off during suspend. I generally hate to talk about non-native speakers grammar etc, but what you have here is in need of a lot of improvement. The below is my attempt to understand what you are trying to say: "For onboard hubs that support USB 3.x and USB 2.0 controllers with shared resets and power supplies, this property is used to identify the controllers with which these are shared." Also - this is one particular system, what prevents there being a hub that has more than 2 controllers? Also, as you insist that this is generic, and not just for genesys, should this not be defined in a common location? Cheers, Conor. > > required: > - compatible > - reg > > +allOf: > + - $ref: usb-device.yaml# > + - if: > + properties: > + compatible: > + contains: > + enum: > + - usb5e3,608 > + then: > + properties: > + peer-hub: false > + vdd-supply: false > + reset-gpios: true > + > + - if: > + properties: > + compatible: > + contains: > + enum: > + - usb5e3,610 > + - usb5e3,620 > + then: > + properties: > + peer-hub: true > + vdd-supply: true > + reset-gpios: true > + > additionalProperties: false > > examples: > @@ -49,3 +82,29 @@ examples: > reset-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>; > }; > }; > + > + - | > + #include <dt-bindings/gpio/gpio.h> > + usb { > + dr_mode = "host"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + /* 2.0 hub on port 1 */ > + hub_2_0: hub@1 { > + compatible = "usb5e3,610"; > + reg = <1>; > + peer-hub = <&hub_3_0>; > + reset-gpios = <&gpio 20 GPIO_ACTIVE_LOW>; > + vdd-supply = <&vcc_5v>; > + }; > + > + /* 3.1 hub on port 4 */ > + hub_3_0: hub@2 { > + compatible = "usb5e3,620"; > + reg = <2>; > + peer-hub = <&hub_2_0>; > + reset-gpios = <&gpio 20 GPIO_ACTIVE_LOW>; > + vdd-supply = <&vcc_5v>; > + }; > + }; > -- > 2.42.0 >
Hi Conor On Thu, 23 Nov 2023 at 23:26, Conor Dooley <conor@kernel.org> wrote: > > On Wed, Nov 22, 2023 at 11:53:46PM +0530, Anand Moon wrote: > > Add the binding example for the USB3.1 Genesys Logic GL3523 > > integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed > > hub. > > > > Onboard USB hub supports USB 3.x and USB 2.0 peer controllers. > > which has a common reset pin and power supply. > > peer-hub phandle each peer controller with proper gpio reset > > and help each peer power on during initialization > > and power off during suspend. > > > > Signed-off-by: Anand Moon <linux.amoon@gmail.com> > > --- > > v4: Fix the description of peer-hub and update the commit message. > > Schematics of the Odroid N2+ > > https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf > > V3: fix the dt_binding_check error, added new example for Genesys GL3523 > > v2: added Genesys GL3523 binding > > v1: none > > --- > > .../bindings/usb/genesys,gl850g.yaml | 67 +++++++++++++++++-- > > 1 file changed, 63 insertions(+), 4 deletions(-) > > > > diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > index ee08b9c3721f..bc3b3f4c8473 100644 > > --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller > > maintainers: > > - Icenowy Zheng <uwu@icenowy.me> > > > > -allOf: > > - - $ref: usb-device.yaml# > > - > > properties: > > compatible: > > enum: > > @@ -27,12 +24,48 @@ properties: > > > > vdd-supply: > > description: > > - the regulator that provides 3.3V core power to the hub. > > + phandle to the regulator that provides power to the hub. > > + > > + peer-hub: > > Should the property not be "peer-controller"? Your description refers to > them as such. No, as per my understanding, peer-hub represents a complete USB hub. See the lock diagram in the below link. > > > + $ref: /schemas/types.yaml#/definitions/phandle > > + description: > > + onboard USB hub supports USB 3.x and USB 2.0 peer controllers. > > > > + which has a common reset pin and power supply. > > + peer-hub phandle each peer controller with proper gpio reset > > + and help each peer power on during initialization > > + and power off during suspend. > > I generally hate to talk about non-native speakers grammar etc, but what > you have here is in need of a lot of improvement. The below is my > attempt to understand what you are trying to say: > > "For onboard hubs that support USB 3.x and USB 2.0 controllers with > shared resets and power supplies, this property is used to identify > the controllers with which these are shared." > Sorry for the poor grammar, I will update this in the next v5. > Also - this is one particular system, what prevents there being a hub > that has more than 2 controllers? Also, as you insist that this is > generic, and not just for genesys, should this not be defined in a > common location? Here is the block diagram of the Genesys GL3523 hub. [0] https://www.genesyslogic.com.tw/en/product_view.php?show=67 [Block Diagram] It has two USB 2.0 and USB 3.1 controllers, so using peer-hub node the onboard hub module will bring up this hub. There are many examples that use similar properties hence it is generic. # Documentation/devicetree/bindings/usb/cypress,hx3.yaml # Documentation/devicetree/bindings/usb/microchip,usb5744.yaml # Documentation/devicetree/bindings/usb/realtek,rts5411.yaml # Documentation/devicetree/bindings/usb/ti,usb8041.yaml # Documentation/devicetree/bindings/usb/vialab,vl817.yaml > > Cheers, > Conor. > Thanks -Anand
On Fri, Nov 24, 2023 at 04:18:23PM +0530, Anand Moon wrote: > Hi Conor > > On Thu, 23 Nov 2023 at 23:26, Conor Dooley <conor@kernel.org> wrote: > > > > On Wed, Nov 22, 2023 at 11:53:46PM +0530, Anand Moon wrote: > > > Add the binding example for the USB3.1 Genesys Logic GL3523 > > > integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed > > > hub. > > > > > > Onboard USB hub supports USB 3.x and USB 2.0 peer controllers. > > > which has a common reset pin and power supply. > > > peer-hub phandle each peer controller with proper gpio reset > > > and help each peer power on during initialization > > > and power off during suspend. > > > > > > Signed-off-by: Anand Moon <linux.amoon@gmail.com> > > > --- > > > v4: Fix the description of peer-hub and update the commit message. > > > Schematics of the Odroid N2+ > > > https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf > > > V3: fix the dt_binding_check error, added new example for Genesys GL3523 > > > v2: added Genesys GL3523 binding > > > v1: none > > > --- > > > .../bindings/usb/genesys,gl850g.yaml | 67 +++++++++++++++++-- > > > 1 file changed, 63 insertions(+), 4 deletions(-) > > > > > > diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > > index ee08b9c3721f..bc3b3f4c8473 100644 > > > --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > > +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > > @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller > > > maintainers: > > > - Icenowy Zheng <uwu@icenowy.me> > > > > > > -allOf: > > > - - $ref: usb-device.yaml# > > > - > > > properties: > > > compatible: > > > enum: > > > @@ -27,12 +24,48 @@ properties: > > > > > > vdd-supply: > > > description: > > > - the regulator that provides 3.3V core power to the hub. > > > + phandle to the regulator that provides power to the hub. > > > + > > > + peer-hub: > > > > Should the property not be "peer-controller"? Your description refers to > > them as such. > > No, as per my understanding, peer-hub represents a complete USB hub. > See the lock diagram in the below link. > > > > > > + $ref: /schemas/types.yaml#/definitions/phandle > > > + description: > > > + onboard USB hub supports USB 3.x and USB 2.0 peer controllers. > > > > > > > + which has a common reset pin and power supply. > > > + peer-hub phandle each peer controller with proper gpio reset This is what I don't get. You say "peer-hub phandle each peer controller..". It is hard for me to understand that portion of the sentence, but the interchanging of "hub" and "controller" is confusing. The title of the binding says "hub controller", so maybe it is better to use that here. > > > + and help each peer power on during initialization > > > + and power off during suspend. > > > > I generally hate to talk about non-native speakers grammar etc, but what > > you have here is in need of a lot of improvement. The below is my > > attempt to understand what you are trying to say: > > > > "For onboard hubs that support USB 3.x and USB 2.0 controllers with > > shared resets and power supplies, this property is used to identify > > the controllers with which these are shared." "For onboard hub controllers that support USB 3.x and USB 2.0 hubs with shared resets and power supplies, this property is used to identify the hubs with which these are shared." I re-worded this again to try and remove the use of "controller". Do you think that this still makes sense? > Sorry for the poor grammar, I will update this in the next v5. > > > Also - this is one particular system, what prevents there being a hub > > that has more than 2 controllers? Also, as you insist that this is > > generic, and not just for genesys, should this not be defined in a > > common location? > > Here is the block diagram of the Genesys GL3523 hub. > [0] https://www.genesyslogic.com.tw/en/product_view.php?show=67 [Block Diagram] > > It has two USB 2.0 and USB 3.1 controllers, so using peer-hub node > the onboard hub module will bring up this hub. > > There are many examples that use similar properties hence it is generic. > > # Documentation/devicetree/bindings/usb/cypress,hx3.yaml > # Documentation/devicetree/bindings/usb/microchip,usb5744.yaml > # Documentation/devicetree/bindings/usb/realtek,rts5411.yaml > # Documentation/devicetree/bindings/usb/ti,usb8041.yaml > # Documentation/devicetree/bindings/usb/vialab,vl817.yaml Which brings me back to the unanswered question, should this not be defined in a common location given there are several devices using it? I assume because it only applies to hub controllers and not other types of devices. Also, the descriptions that I saw when looking at some of those other bindings are similarly poor. I can't bring myself to care any more, just clean up the ambiguous wording here and I'll ack the next version, I don't expect you to sort out the wording in other bindings. Cheers, Conor.
Hi Conor, On Fri, 24 Nov 2023 at 17:55, Conor Dooley <conor@kernel.org> wrote: > > On Fri, Nov 24, 2023 at 04:18:23PM +0530, Anand Moon wrote: > > Hi Conor > > > > On Thu, 23 Nov 2023 at 23:26, Conor Dooley <conor@kernel.org> wrote: > > > > > > On Wed, Nov 22, 2023 at 11:53:46PM +0530, Anand Moon wrote: > > > > Add the binding example for the USB3.1 Genesys Logic GL3523 > > > > integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed > > > > hub. > > > > > > > > Onboard USB hub supports USB 3.x and USB 2.0 peer controllers. > > > > which has a common reset pin and power supply. > > > > peer-hub phandle each peer controller with proper gpio reset > > > > and help each peer power on during initialization > > > > and power off during suspend. > > > > > > > > Signed-off-by: Anand Moon <linux.amoon@gmail.com> > > > > --- > > > > v4: Fix the description of peer-hub and update the commit message. > > > > Schematics of the Odroid N2+ > > > > https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf > > > > V3: fix the dt_binding_check error, added new example for Genesys GL3523 > > > > v2: added Genesys GL3523 binding > > > > v1: none > > > > --- > > > > .../bindings/usb/genesys,gl850g.yaml | 67 +++++++++++++++++-- > > > > 1 file changed, 63 insertions(+), 4 deletions(-) > > > > > > > > diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > > > index ee08b9c3721f..bc3b3f4c8473 100644 > > > > --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > > > +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml > > > > @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller > > > > maintainers: > > > > - Icenowy Zheng <uwu@icenowy.me> > > > > > > > > -allOf: > > > > - - $ref: usb-device.yaml# > > > > - > > > > properties: > > > > compatible: > > > > enum: > > > > @@ -27,12 +24,48 @@ properties: > > > > > > > > vdd-supply: > > > > description: > > > > - the regulator that provides 3.3V core power to the hub. > > > > + phandle to the regulator that provides power to the hub. > > > > + > > > > + peer-hub: > > > > > > Should the property not be "peer-controller"? Your description refers to > > > them as such. > > > > No, as per my understanding, peer-hub represents a complete USB hub. > > See the lock diagram in the below link. > > > > > > > > > + $ref: /schemas/types.yaml#/definitions/phandle > > > > + description: > > > > + onboard USB hub supports USB 3.x and USB 2.0 peer controllers. > > > > > > > > > > + which has a common reset pin and power supply. > > > > + peer-hub phandle each peer controller with proper gpio reset > > This is what I don't get. You say "peer-hub phandle each peer > controller..". It is hard for me to understand that portion of the > sentence, but the interchanging of "hub" and "controller" is > confusing. The title of the binding says "hub controller", so maybe it > is better to use that here. > > > > > + and help each peer power on during initialization > > > > + and power off during suspend. > > > > > > I generally hate to talk about non-native speakers grammar etc, but what > > > you have here is in need of a lot of improvement. The below is my > > > attempt to understand what you are trying to say: > > > > > > "For onboard hubs that support USB 3.x and USB 2.0 controllers with > > > shared resets and power supplies, this property is used to identify > > > the controllers with which these are shared." > > "For onboard hub controllers that support USB 3.x and USB 2.0 hubs > with shared resets and power supplies, this property is used to identify > the hubs with which these are shared." > Thanks for your review comments. Ok will update this in the next version. > I re-worded this again to try and remove the use of "controller". > Do you think that this still makes sense? > > > Sorry for the poor grammar, I will update this in the next v5. > > > > > Also - this is one particular system, what prevents there being a hub > > > that has more than 2 controllers? Also, as you insist that this is > > > generic, and not just for genesys, should this not be defined in a > > > common location? > > > > Here is the block diagram of the Genesys GL3523 hub. > > [0] https://www.genesyslogic.com.tw/en/product_view.php?show=67 [Block Diagram] > > > > It has two USB 2.0 and USB 3.1 controllers, so using peer-hub node > > the onboard hub module will bring up this hub. > > > > There are many examples that use similar properties hence it is generic. > > > > # Documentation/devicetree/bindings/usb/cypress,hx3.yaml > > # Documentation/devicetree/bindings/usb/microchip,usb5744.yaml > > # Documentation/devicetree/bindings/usb/realtek,rts5411.yaml > > # Documentation/devicetree/bindings/usb/ti,usb8041.yaml > > # Documentation/devicetree/bindings/usb/vialab,vl817.yaml > > Which brings me back to the unanswered question, should this not be > defined in a common location given there are several devices using it? > I assume because it only applies to hub controllers and not other types > of devices. > > Also, the descriptions that I saw when looking at some of those other > bindings are similarly poor. I can't bring myself to care any more, > just clean up the ambiguous wording here and I'll ack the next version, > I don't expect you to sort out the wording in other bindings. > Ok > Cheers, > Conor. Thanks -Anand
diff --git a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml index ee08b9c3721f..bc3b3f4c8473 100644 --- a/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml +++ b/Documentation/devicetree/bindings/usb/genesys,gl850g.yaml @@ -9,9 +9,6 @@ title: Genesys Logic USB hub controller maintainers: - Icenowy Zheng <uwu@icenowy.me> -allOf: - - $ref: usb-device.yaml# - properties: compatible: enum: @@ -27,12 +24,48 @@ properties: vdd-supply: description: - the regulator that provides 3.3V core power to the hub. + phandle to the regulator that provides power to the hub. + + peer-hub: + $ref: /schemas/types.yaml#/definitions/phandle + description: + onboard USB hub supports USB 3.x and USB 2.0 peer controllers. + which has a common reset pin and power supply. + peer-hub phandle each peer controller with proper gpio reset + and help each peer power on during initialization + and power off during suspend. required: - compatible - reg +allOf: + - $ref: usb-device.yaml# + - if: + properties: + compatible: + contains: + enum: + - usb5e3,608 + then: + properties: + peer-hub: false + vdd-supply: false + reset-gpios: true + + - if: + properties: + compatible: + contains: + enum: + - usb5e3,610 + - usb5e3,620 + then: + properties: + peer-hub: true + vdd-supply: true + reset-gpios: true + additionalProperties: false examples: @@ -49,3 +82,29 @@ examples: reset-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>; }; }; + + - | + #include <dt-bindings/gpio/gpio.h> + usb { + dr_mode = "host"; + #address-cells = <1>; + #size-cells = <0>; + + /* 2.0 hub on port 1 */ + hub_2_0: hub@1 { + compatible = "usb5e3,610"; + reg = <1>; + peer-hub = <&hub_3_0>; + reset-gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + vdd-supply = <&vcc_5v>; + }; + + /* 3.1 hub on port 4 */ + hub_3_0: hub@2 { + compatible = "usb5e3,620"; + reg = <2>; + peer-hub = <&hub_2_0>; + reset-gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + vdd-supply = <&vcc_5v>; + }; + };
Add the binding example for the USB3.1 Genesys Logic GL3523 integrates with USB 3.1 Gen 1 Super Speed and USB 2.0 High-Speed hub. Onboard USB hub supports USB 3.x and USB 2.0 peer controllers. which has a common reset pin and power supply. peer-hub phandle each peer controller with proper gpio reset and help each peer power on during initialization and power off during suspend. Signed-off-by: Anand Moon <linux.amoon@gmail.com> --- v4: Fix the description of peer-hub and update the commit message. Schematics of the Odroid N2+ https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf V3: fix the dt_binding_check error, added new example for Genesys GL3523 v2: added Genesys GL3523 binding v1: none --- .../bindings/usb/genesys,gl850g.yaml | 67 +++++++++++++++++-- 1 file changed, 63 insertions(+), 4 deletions(-)