@@ -18,6 +18,12 @@
#define PHY_ID_ADIN1110 0x0283bc91
#define PHY_ID_ADIN2111 0x0283bca1
+#define ADIN_PHY_SUBSYS_IRQ_MASK 0x0021
+#define ADIN_LINK_STAT_CHNG_IRQ_EN BIT(1)
+
+#define ADIN_PHY_SUBSYS_IRQ_STATUS 0x0011
+#define ADIN_LINK_STAT_CHNG BIT(1)
+
#define ADIN_FORCED_MODE 0x8000
#define ADIN_FORCED_MODE_EN BIT(0)
@@ -136,6 +142,59 @@ static int adin_config_aneg(struct phy_device *phydev)
return genphy_c45_config_aneg(phydev);
}
+static int adin_phy_ack_intr(struct phy_device *phydev)
+{
+ /* Clear pending interrupts */
+ int rc = phy_read_mmd(phydev, MDIO_MMD_VEND2,
+ ADIN_PHY_SUBSYS_IRQ_STATUS);
+
+ return rc < 0 ? rc : 0;
+}
+
+static int adin_config_intr(struct phy_device *phydev)
+{
+ int ret, regval;
+
+ ret = adin_phy_ack_intr(phydev);
+
+ if (ret)
+ return ret;
+
+ regval = phy_read_mmd(phydev, MDIO_MMD_VEND2,
+ ADIN_PHY_SUBSYS_IRQ_MASK);
+ if (regval < 0)
+ return regval;
+
+ if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
+ regval |= ADIN_LINK_STAT_CHNG_IRQ_EN;
+ else
+ regval &= ~ADIN_LINK_STAT_CHNG_IRQ_EN;
+
+ ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
+ ADIN_PHY_SUBSYS_IRQ_MASK,
+ regval);
+ return ret;
+}
+
+static irqreturn_t adin_phy_handle_interrupt(struct phy_device *phydev)
+{
+ int irq_status;
+
+ irq_status = phy_read_mmd(phydev, MDIO_MMD_VEND2,
+ ADIN_PHY_SUBSYS_IRQ_STATUS);
+ if (irq_status < 0) {
+ phy_error(phydev);
+ return IRQ_NONE;
+ }
+
+ if (!(irq_status & ADIN_LINK_STAT_CHNG))
+ return IRQ_NONE;
+
+ phy_trigger_machine(phydev);
+
+ return IRQ_HANDLED;
+}
+
static int adin_set_powerdown_mode(struct phy_device *phydev, bool en)
{
int ret;
@@ -275,6 +334,8 @@ static struct phy_driver adin_driver[] = {
.probe = adin_probe,
.config_aneg = adin_config_aneg,
.read_status = adin_read_status,
+ .config_intr = adin_config_intr,
+ .handle_interrupt = adin_phy_handle_interrupt,
.set_loopback = adin_set_loopback,
.suspend = adin_suspend,
.resume = adin_resume,
An interrupt handler was added to the driver as well as functions to enable interrupts at the phy. There are several interrupts maskable at the phy, but only link change interrupts are handled by the driver yet. Signed-off-by: Andre Werner <andre.werner@systec-electronic.com> --- v3: - Correct rashly format error that was reported by checker. --- drivers/net/phy/adin1100.c | 61 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 61 insertions(+)