@@ -36,6 +36,16 @@ config TYPEC_MUX_INTEL_PMC
control the USB role switch and also the multiplexer/demultiplexer
switches used with USB Type-C Alternate Modes.
+config TYPEC_MUX_IT5205
+ tristate "ITE IT5205 Type-C USB Alt Mode Passive MUX driver"
+ depends on I2C
+ select REGMAP_I2C
+ help
+ Driver for the ITE IT5205 Type-C USB Alternate Mode Passive MUX
+ which provides support for muxing DisplayPort and sideband signals
+ on a common USB Type-C connector.
+ If compiled as a module, the module will be named it5205.
+
config TYPEC_MUX_NB7VPQ904M
tristate "On Semiconductor NB7VPQ904M Type-C redriver driver"
depends on I2C
@@ -4,6 +4,7 @@ obj-$(CONFIG_TYPEC_MUX_FSA4480) += fsa4480.o
obj-$(CONFIG_TYPEC_MUX_GPIO_SBU) += gpio-sbu-mux.o
obj-$(CONFIG_TYPEC_MUX_PI3USB30532) += pi3usb30532.o
obj-$(CONFIG_TYPEC_MUX_INTEL_PMC) += intel_pmc_mux.o
+obj-$(CONFIG_TYPEC_MUX_IT5205) += it5205.o
obj-$(CONFIG_TYPEC_MUX_NB7VPQ904M) += nb7vpq904m.o
obj-$(CONFIG_TYPEC_MUX_PTN36502) += ptn36502.o
obj-$(CONFIG_TYPEC_MUX_WCD939X_USBSS) += wcd939x-usbss.o
new file mode 100644
@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ITE IT5205 Type-C USB alternate mode passive mux
+ *
+ * Copyright (c) 2020 MediaTek Inc.
+ * Copyright (c) 2024 Collabora Ltd.
+ * AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/usb/tcpm.h>
+#include <linux/usb/typec.h>
+#include <linux/usb/typec_dp.h>
+#include <linux/usb/typec_mux.h>
+
+#define IT5205_REG_CHIP_ID(x) (0x4 + (x))
+#define IT5205FN_CHIP_ID 0x35323035 /* "5205" */
+
+/* MUX power down register */
+#define IT5205_REG_MUXPDR 0x10
+#define IT5205_MUX_POWER_DOWN BIT(0)
+
+/* MUX control register */
+#define IT5205_REG_MUXCR 0x11
+#define IT5205_POLARITY_INVERTED BIT(4)
+#define IT5205_DP_USB_CTRL_MASK GENMASK(3, 0)
+#define IT5205_DP 0x0f
+#define IT5205_DP_USB 0x03
+#define IT5205_USB 0x07
+
+/* Vref Select Register */
+#define IT5205_REG_VSR 0x10
+#define IT5205_VREF_SELECT_MASK GENMASK(5, 4)
+#define IT5205_VREF_SELECT_3_3V 0x00
+#define IT5205_VREF_SELECT_OFF 0x20
+
+/* CSBU Over Voltage Protection Register */
+#define IT5205_REG_CSBUOVPSR 0x1e
+#define IT5205_OVP_SELECT_MASK GENMASK(5, 4)
+#define IT5205_OVP_3_90V 0x00
+#define IT5205_OVP_3_68V 0x10
+#define IT5205_OVP_3_62V 0x20
+#define IT5205_OVP_3_57V 0x30
+
+/* CSBU Switch Register */
+#define IT5205_REG_CSBUSR 0x22
+#define IT5205_CSBUSR_SWITCH BIT(0)
+
+/* Interrupt Switch Register */
+#define IT5205_REG_ISR 0x25
+#define IT5205_ISR_CSBU_MASK BIT(4)
+#define IT5205_ISR_CSBU_OVP BIT(0)
+
+struct it5205 {
+ struct i2c_client *client;
+ struct regmap *regmap;
+ struct typec_switch_dev *sw;
+ struct typec_mux_dev *mux;
+};
+
+static int it5205_switch_set(struct typec_switch_dev *sw, enum typec_orientation orientation)
+{
+ struct it5205 *it = typec_switch_get_drvdata(sw);
+
+ switch (orientation) {
+ case TYPEC_ORIENTATION_NORMAL:
+ regmap_update_bits(it->regmap, IT5205_REG_MUXCR,
+ IT5205_POLARITY_INVERTED, 0);
+ break;
+ case TYPEC_ORIENTATION_REVERSE:
+ regmap_update_bits(it->regmap, IT5205_REG_MUXCR,
+ IT5205_POLARITY_INVERTED, IT5205_POLARITY_INVERTED);
+ break;
+ case TYPEC_ORIENTATION_NONE:
+ fallthrough;
+ default:
+ regmap_write(it->regmap, IT5205_REG_MUXCR, 0);
+ break;
+ }
+
+ return 0;
+}
+
+static int it5205_mux_set(struct typec_mux_dev *mux, struct typec_mux_state *state)
+{
+ struct it5205 *it = typec_mux_get_drvdata(mux);
+ u8 val;
+
+ if (state->mode >= TYPEC_STATE_MODAL &&
+ state->alt->svid != USB_TYPEC_DP_SID)
+ return -EINVAL;
+
+ switch (state->mode) {
+ case TYPEC_STATE_USB:
+ val = IT5205_USB;
+ break;
+ case TYPEC_DP_STATE_C:
+ fallthrough;
+ case TYPEC_DP_STATE_E:
+ val = IT5205_DP;
+ break;
+ case TYPEC_DP_STATE_D:
+ val = IT5205_DP_USB;
+ break;
+ case TYPEC_STATE_SAFE:
+ fallthrough;
+ default:
+ val = 0;
+ break;
+ }
+
+ return regmap_update_bits(it->regmap, IT5205_REG_MUXCR,
+ IT5205_DP_USB_CTRL_MASK, val);
+}
+
+static irqreturn_t it5205_irq_handler(int irq, void *data)
+{
+ struct it5205 *it = data;
+ int ret;
+ u32 val;
+
+ ret = regmap_read(it->regmap, IT5205_REG_ISR, &val);
+ if (ret)
+ return IRQ_NONE;
+
+ if (val & IT5205_ISR_CSBU_OVP) {
+ dev_warn(&it->client->dev, "Overvoltage detected!\n");
+
+ /* Reset CSBU */
+ regmap_update_bits(it->regmap, IT5205_REG_CSBUSR,
+ IT5205_CSBUSR_SWITCH, 0);
+ regmap_update_bits(it->regmap, IT5205_REG_CSBUSR,
+ IT5205_CSBUSR_SWITCH, IT5205_CSBUSR_SWITCH);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static void it5205_enable_ovp(struct it5205 *it)
+{
+ /* Select Vref 3.3v */
+ regmap_update_bits(it->regmap, IT5205_REG_VSR,
+ IT5205_VREF_SELECT_MASK, IT5205_VREF_SELECT_3_3V);
+
+ /* Trigger OVP at 3.68V */
+ regmap_update_bits(it->regmap, IT5205_REG_CSBUOVPSR,
+ IT5205_OVP_SELECT_MASK, IT5205_OVP_3_68V);
+
+ /* Unmask OVP interrupt */
+ regmap_update_bits(it->regmap, IT5205_REG_ISR,
+ IT5205_ISR_CSBU_MASK, 0);
+
+ /* Enable CSBU Interrupt */
+ regmap_update_bits(it->regmap, IT5205_REG_CSBUSR,
+ IT5205_CSBUSR_SWITCH, IT5205_CSBUSR_SWITCH);
+}
+
+static const struct regmap_config it5205_regmap = {
+ .max_register = 0x2f,
+ .reg_bits = 8,
+ .val_bits = 8,
+};
+
+static int it5205_probe(struct i2c_client *client)
+{
+ struct typec_switch_desc sw_desc = { };
+ struct typec_mux_desc mux_desc = { };
+ struct device *dev = &client->dev;
+ struct it5205 *it;
+ u32 val, chipid = 0;
+ int i, ret;
+
+ it = devm_kzalloc(dev, sizeof(*it), GFP_KERNEL);
+ if (!it)
+ return -ENOMEM;
+
+ ret = devm_regulator_get_enable(dev, "vcc");
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to get regulator\n");
+
+ it->client = client;
+
+ it->regmap = devm_regmap_init_i2c(client, &it5205_regmap);
+ if (IS_ERR(it->regmap))
+ return dev_err_probe(dev, PTR_ERR(it->regmap),
+ "Failed to init regmap\n");
+
+ /* IT5205 needs a long time to power up after enabling regulator */
+ msleep(50);
+
+ /* Unset poweroff bit */
+ ret = regmap_write(it->regmap, IT5205_REG_MUXPDR, 0);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to set power on\n");
+
+ /* Read the 32 bits ChipID */
+ for (i = 3; i >= 0; i--) {
+ ret = regmap_read(it->regmap, IT5205_REG_CHIP_ID(i), &val);
+ if (ret)
+ return ret;
+
+ chipid |= val << (i * 8);
+ }
+
+ if (chipid != IT5205FN_CHIP_ID)
+ return dev_err_probe(dev, -EINVAL,
+ "Unknown ChipID 0x%x\n", chipid);
+
+ /* Initialize as USB mode with default (non-inverted) polarity */
+ ret = regmap_write(it->regmap, IT5205_REG_MUXCR, IT5205_USB);
+ if (ret)
+ return dev_err_probe(dev, ret, "Cannot set mode to USB\n");
+
+ sw_desc.drvdata = it;
+ sw_desc.fwnode = dev_fwnode(dev);
+ sw_desc.set = it5205_switch_set;
+
+ it->sw = typec_switch_register(dev, &sw_desc);
+ if (IS_ERR(it->sw))
+ return dev_err_probe(dev, PTR_ERR(it->sw),
+ "failed to register typec switch\n");
+
+ mux_desc.drvdata = it;
+ mux_desc.fwnode = dev_fwnode(dev);
+ mux_desc.set = it5205_mux_set;
+
+ it->mux = typec_mux_register(dev, &mux_desc);
+ if (IS_ERR(it->mux)) {
+ typec_switch_unregister(it->sw);
+ return dev_err_probe(dev, PTR_ERR(it->mux),
+ "failed to register typec mux\n");
+ }
+
+ i2c_set_clientdata(client, it);
+
+ if (of_property_read_bool(dev->of_node, "ite,ovp-enable") && client->irq) {
+ it5205_enable_ovp(it);
+
+ ret = devm_request_threaded_irq(dev, client->irq, NULL,
+ it5205_irq_handler,
+ IRQF_ONESHOT, dev_name(dev), it);
+ if (ret) {
+ typec_mux_unregister(it->mux);
+ typec_switch_unregister(it->sw);
+ return dev_err_probe(dev, ret, "Failed to request irq\n");
+ }
+ }
+
+ return 0;
+}
+
+static void it5205_remove(struct i2c_client *client)
+{
+ struct it5205 *it = i2c_get_clientdata(client);
+
+ typec_mux_unregister(it->mux);
+ typec_switch_unregister(it->sw);
+}
+
+static const struct i2c_device_id it5205_table[] = {
+ { "it5205" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(i2c, it5205_table);
+
+static const struct of_device_id it5205_of_table[] = {
+ { .compatible = "ite,it5205" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, it5205_match_table);
+
+static struct i2c_driver it5205_driver = {
+ .driver = {
+ .name = "it5205",
+ .of_match_table = it5205_of_table,
+ },
+ .probe = it5205_probe,
+ .remove = it5205_remove,
+ .id_table = it5205_table,
+};
+module_i2c_driver(it5205_driver);
+
+MODULE_AUTHOR("Tianping Fang <tianping.fang@mediatek.com>");
+MODULE_AUTHOR("AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>");
+MODULE_DESCRIPTION("ITE IT5205 alternate mode passive MUX driver");
+MODULE_LICENSE("GPL");
The ITE IT5202 is a USB Type-C Alternate Mode Passive MUX, used for muxing the SBU lines of a Type-C port with DisplayPort altmode and also providing an orientation switch. Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> --- drivers/usb/typec/mux/Kconfig | 10 ++ drivers/usb/typec/mux/Makefile | 1 + drivers/usb/typec/mux/it5205.c | 294 +++++++++++++++++++++++++++++++++ 3 files changed, 305 insertions(+) create mode 100644 drivers/usb/typec/mux/it5205.c