diff mbox series

[v1,2/2] arm: dts: nxp: imx: Add support for Apalis Evaluation Board v1.2

Message ID 20240122123526.43400-3-hiagofranco@gmail.com (mailing list archive)
State New, archived
Headers show
Series nxp: imx: Add support for Apalis Evaluation Board v1.2 | expand

Commit Message

Hiago De Franco Jan. 22, 2024, 12:35 p.m. UTC
From: Hiago De Franco <hiago.franco@toradex.com>

Add support for the new Apalis Evaluation Board v1.2. Because
only the imx6q-apalis-eval.dts was available, the imx6q-apalis-eval.dtsi
has been created which has common hardware configurations for v1.0, v1.1
and v1.2. Both imx6q-apalis-eval.dts and imx6q-apalis-eval-v1.2.dts
files include imx6q-apalis-eval.dtsi.

Versions 1.0 and 1.1 are compatible with each other and should
use imx6q-apalis-eval.dts file. Now for v1.2, the new device-tree file
should be used.

Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
---
 arch/arm/boot/dts/nxp/imx/Makefile            |   1 +
 .../dts/nxp/imx/imx6q-apalis-eval-v1.2.dts    | 198 ++++++++++++++++++
 .../boot/dts/nxp/imx/imx6q-apalis-eval.dts    | 108 +---------
 .../boot/dts/nxp/imx/imx6q-apalis-eval.dtsi   | 120 +++++++++++
 4 files changed, 321 insertions(+), 106 deletions(-)
 create mode 100644 arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts
 create mode 100644 arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi

Comments

Francesco Dolcini Jan. 22, 2024, 5:35 p.m. UTC | #1
On Mon, Jan 22, 2024 at 09:35:00AM -0300, Hiago De Franco wrote:
> From: Hiago De Franco <hiago.franco@toradex.com>
> 
> Add support for the new Apalis Evaluation Board v1.2. Because
> only the imx6q-apalis-eval.dts was available, the imx6q-apalis-eval.dtsi
> has been created which has common hardware configurations for v1.0, v1.1
> and v1.2. Both imx6q-apalis-eval.dts and imx6q-apalis-eval-v1.2.dts
> files include imx6q-apalis-eval.dtsi.
> 
> Versions 1.0 and 1.1 are compatible with each other and should
> use imx6q-apalis-eval.dts file. Now for v1.2, the new device-tree file
> should be used.
> 
> Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>

Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
index a724d1a7a9a0..0473f9b86ec7 100644
--- a/arch/arm/boot/dts/nxp/imx/Makefile
+++ b/arch/arm/boot/dts/nxp/imx/Makefile
@@ -147,6 +147,7 @@  dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-yapp4-phoenix.dtb \
 	imx6dl-yapp4-ursa.dtb \
 	imx6q-apalis-eval.dtb \
+	imx6q-apalis-eval-v1.2.dtb \
 	imx6q-apalis-ixora.dtb \
 	imx6q-apalis-ixora-v1.1.dtb \
 	imx6q-apalis-ixora-v1.2.dtb \
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts
new file mode 100644
index 000000000000..2fba7ed1061c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts
@@ -0,0 +1,198 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6q-apalis-eval.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module on Apalis Evaluation Board v1.2";
+	compatible = "toradex,apalis_imx6q-eval-v1.2", "toradex,apalis_imx6q",
+		     "fsl,imx6q";
+
+	reg_3v3_mmc: regulator-3v3-mmc {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_3v3_mmc>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V_MMC";
+		startup-delay-us = <100>;
+	};
+
+	reg_3v3_sd: regulator-3v3-sd {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_3v3_sd>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V_SD";
+		startup-delay-us = <100>;
+	};
+
+	reg_can1: regulator-can1 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_can1_power>;
+		regulator-name = "5V_SW_CAN1";
+		startup-delay-us = <1000>;
+	};
+
+	reg_can2: regulator-can2 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_can2_power>;
+		regulator-name = "5V_SW_CAN2";
+		startup-delay-us = <1000>;
+	};
+
+	sound-carrier {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&codec_dai>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&codec_dai>;
+		simple-audio-card,name = "apalis-nau8822";
+		simple-audio-card,routing =
+			"Headphones", "LHP",
+			"Headphones", "RHP",
+			"Speaker", "LSPK",
+			"Speaker", "RSPK",
+			"Line Out", "AUXOUT1",
+			"Line Out", "AUXOUT2",
+			"LAUX", "Line In",
+			"RAUX", "Line In",
+			"LMICP", "Mic In",
+			"RMICP", "Mic In";
+		simple-audio-card,widgets =
+			"Headphones", "Headphones",
+			"Line Out", "Line Out",
+			"Speaker", "Speaker",
+			"Microphone", "Mic In",
+			"Line", "Line In";
+
+		codec_dai: simple-audio-card,codec {
+			sound-dai = <&nau8822_1a>;
+			system-clock-frequency = <12288000>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi2>;
+		};
+	};
+};
+
+&can1 {
+	xceiver-supply = <&reg_can1>;
+	status = "okay";
+};
+
+&can2 {
+	xceiver-supply = <&reg_can2>;
+	status = "okay";
+};
+
+/* I2C1_SDA/SCL on MXM3 209/211 */
+&i2c1 {
+	/* Audio Codec */
+	nau8822_1a: audio-codec@1a {
+		compatible = "nuvoton,nau8822";
+		reg = <0x1a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_nau8822>;
+		#sound-dai-cells = <0>;
+	};
+
+	/* Current measurement into module VCC */
+	hwmon@40 {
+		compatible = "ti,ina219";
+		reg = <0x40>;
+		shunt-resistor = <5000>;
+	};
+
+	/* Temperature Sensor */
+	temperature-sensor@4f {
+		compatible = "ti,tmp75c";
+		reg = <0x4f>;
+	};
+
+	/* EEPROM */
+	eeprom@57 {
+		compatible = "st,24c02", "atmel,24c02";
+		reg = <0x57>;
+		pagesize = <16>;
+		size = <256>;
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&ssi2 {
+	status = "okay";
+};
+
+/* MMC1 */
+&usdhc1 {
+	bus-width = <4>;
+	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_mmc_cd>;
+	vmmc-supply = <&reg_3v3_mmc>;
+	status = "okay";
+};
+
+/* SD1 */
+&usdhc2 {
+	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
+	vmmc-supply = <&reg_3v3_sd>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enable_3v3_mmc: enable3v3mmcgrp {
+		fsl,pins = <
+			/* MMC1_PWR_CTRL */
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0xb000
+		>;
+	};
+
+	pinctrl_enable_3v3_sd: enable3v3sdgrp {
+		fsl,pins = <
+			/* SD1_PWR_CTRL */
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0xb000
+		>;
+	};
+
+	pinctrl_enable_can1_power: enablecan1powergrp {
+		fsl,pins = <
+			/* CAN1_PWR_EN */
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0xb000
+		>;
+	};
+
+	pinctrl_enable_can2_power: enablecan2powergrp {
+		fsl,pins = <
+			/* CAN2_PWR_EN */
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0xb000
+		>;
+	};
+
+	pinctrl_nau8822: nau8822grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT16__AUD5_TXC	0x130b0
+			MX6QDL_PAD_DISP0_DAT17__AUD5_TXD	0x130b0
+			MX6QDL_PAD_DISP0_DAT18__AUD5_TXFS	0x130b0
+			MX6QDL_PAD_DISP0_DAT19__AUD5_RXD	0x130b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
index 3fc079dfd61e..e1077e2da5f4 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
@@ -7,29 +7,13 @@ 
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "imx6q.dtsi"
-#include "imx6qdl-apalis.dtsi"
+#include "imx6q-apalis-eval.dtsi"
 
 / {
 	model = "Toradex Apalis iMX6Q/D Module on Apalis Evaluation Board";
 	compatible = "toradex,apalis_imx6q-eval", "toradex,apalis_imx6q",
 		     "fsl,imx6q";
 
-	aliases {
-		i2c0 = &i2c1;
-		i2c1 = &i2c3;
-		i2c2 = &i2c2;
-		rtc0 = &rtc_i2c;
-		rtc1 = &snvs_rtc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	reg_pcie_switch: regulator-pcie-switch {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -40,14 +24,6 @@  reg_pcie_switch: regulator-pcie-switch {
 		startup-delay-us = <100000>;
 		status = "okay";
 	};
-
-	reg_3v3_sw: regulator-3v3-sw {
-		compatible = "regulator-fixed";
-		regulator-always-on;
-		regulator-max-microvolt = <3300000>;
-		regulator-min-microvolt = <3300000>;
-		regulator-name = "3.3V_SW";
-	};
 };
 
 &can1 {
@@ -62,102 +38,22 @@  &can2 {
 
 /* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
 &i2c1 {
-	status = "okay";
-
+	/* PCIe Switch */
 	pcie-switch@58 {
 		compatible = "plx,pex8605";
 		reg = <0x58>;
 	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc_i2c: rtc@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-/*
- * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
- * board)
- */
-&i2c3 {
-	status = "okay";
 };
 
 &pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_reset_moci>;
-	/* active-high meaning opposite of regular PERST# active-low polarity */
-	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
-	reset-gpio-active-high;
 	vpcie-supply = <&reg_pcie_switch>;
 	status = "okay";
 };
 
-&pwm1 {
-	status = "okay";
-};
-
-&pwm2 {
-	status = "okay";
-};
-
-&pwm3 {
-	status = "okay";
-};
-
-&pwm4 {
-	status = "okay";
-};
-
-&reg_usb_host_vbus {
-	status = "okay";
-};
-
-&reg_usb_otg_vbus {
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-};
-
 &sound_spdif {
 	status = "okay";
 };
 
-&spdif {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&uart4 {
-	status = "okay";
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&usbh1 {
-	disable-over-current;
-	vbus-supply = <&reg_usb_host_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	disable-over-current;
-	vbus-supply = <&reg_usb_otg_vbus>;
-	status = "okay";
-};
-
 /* MMC1 */
 &usdhc1 {
 	status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
new file mode 100644
index 000000000000..b6c45ad3f430
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
@@ -0,0 +1,120 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2024 Toradex
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6q.dtsi"
+#include "imx6qdl-apalis.dtsi"
+
+/ {
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c3;
+		i2c2 = &i2c2;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_3v3_sw: regulator-3v3-sw {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V_SW";
+	};
+};
+
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+/*
+ * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
+ * board)
+ */
+&i2c3 {
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_reset_moci>;
+	/* active-high meaning opposite of regular PERST# active-low polarity */
+	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+	reset-gpio-active-high;
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&reg_usb_otg_vbus {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	vbus-supply = <&reg_usb_host_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};