| Message ID | 20240127001926.495769-4-andre.draszik@linaro.org (mailing list archive) |
|---|---|
| State | Superseded, archived |
| Headers | show |
| Series | [1/9] clk: samsung: gs-101: drop extra empty line | expand |
On Sat, 2024-01-27 at 00:19 +0000, André Draszik wrote: > The clocks marked as CLK_IGNORE_UNUSED need to be kept on until we have > updated the respective drivers for the following reasons: > * gout_peric1_gpio_peric1_pclk is required by the pinctrl > configuration. With this clock disabled, reconfiguring the pins > (for USI/I2C, USI/UART) will hang during register access. > Since pingctrl-samsung doesn't support a clock at the moment, we > just keep the kernel from disabling it at boot, until we have an > update for samsung-pinctrl, at which point we'll drop the flag. I have patches for pinctrl-samsung implementing this new clock ready. Will send next week. Cheers, Andre'
On Fri, Jan 26, 2024 at 6:19 PM André Draszik <andre.draszik@linaro.org> wrote: > > CMU_PERIC1 is the clock management unit used for the peric1 block which > is used for additional USI, I3C and PWM interfaces/busses. Add support > for muxes, dividers and gates of cmu_peric1, except for > CLK_GOUT_PERIC1_IP which isn't well described in the datasheet and > which downstream also ignores (similar to cmu_peric0). > > Two clocks have been marked as CLK_IS_CRITICAL for the following > reason: > * disabling them makes it impossible to access any peric1 > registers, (including those two registers). > * disabling gout_peric1_lhm_axi_p_peric1_i_clk sometimes has the > additional effect of making the whole system unresponsive. > > The clocks marked as CLK_IGNORE_UNUSED need to be kept on until we have > updated the respective drivers for the following reasons: > * gout_peric1_gpio_peric1_pclk is required by the pinctrl > configuration. With this clock disabled, reconfiguring the pins > (for USI/I2C, USI/UART) will hang during register access. > Since pingctrl-samsung doesn't support a clock at the moment, we > just keep the kernel from disabling it at boot, until we have an > update for samsung-pinctrl, at which point we'll drop the flag. > * gout_peric1_sysreg_peric1_pclk needs to be hooked up to > sysreg_peric1 in DT which will be done in a followup-patch, at > which point we'll drop the special treatment from here. We're > adding the flag temporarily here so as to not break the boot (due > to pclk otherwise getting disabled). > > Signed-off-by: André Draszik <andre.draszik@linaro.org> > > --- Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> > Note for future reference: To ensure consistent naming throughout this > driver, the clock names have been derived from the data sheet using the > following, with the expectation for all future additions to this file > to use the same: > sed \ > -e 's|^PLL_LOCKTIME_PLL_\([^_]\+\)|fout_\L\1_pll|' \ > \ > -e 's|^PLL_CON0_MUX_CLKCMU_\([^_]\+\)_\(.*\)|mout_\L\1_\2|' \ > -e 's|^PLL_CON0_PLL_\(.*\)|mout_pll_\L\1|' \ > -e 's|^CLK_CON_MUX_MUX_CLK_\(.*\)|mout_\L\1|' \ > -e '/^PLL_CON[1-4]_[^_]\+_/d' \ > -e '/^[^_]\+_CMU_[^_]\+_CONTROLLER_OPTION/d' \ > -e '/^CLKOUT_CON_BLK_[^_]\+_CMU_[^_]\+_CLKOUT0/d' \ > \ > -e 's|_IPCLKPORT||' \ > -e 's|_RSTNSYNC||' \ > \ > -e 's|^CLK_CON_DIV_DIV_CLK_\([^_]\+\)_\(.*\)|dout_\L\1_\2|' \ > \ > -e 's|^CLK_CON_BUF_CLKBUF_\([^_]\+\)_\(.*\)|gout_\L\1_\2|' \ > -e 's|^CLK_CON_GAT_CLK_BLK_\([^_]\+\)_UID_\(.*\)|gout_\L\1_\2|' \ > -e 's|^gout_[^_]\+_[^_]\+_cmu_\([^_]\+\)_pclk$|gout_\1_\1_pclk|' \ > -e 's|^CLK_CON_GAT_GOUT_BLK_\([^_]\+\)_UID_\(.*\)|gout_\L\1_\2|' \ > -e 's|^CLK_CON_GAT_CLK_\([^_]\+\)_\(.*\)|gout_\L\1_clk_\L\1_\2|' \ > \ > -e '/^\(DMYQCH\|PCH\|QCH\|QUEUE\)_/d' > --- > drivers/clk/samsung/clk-gs101.c | 346 ++++++++++++++++++++++++++++++++ > 1 file changed, 346 insertions(+) > > diff --git a/drivers/clk/samsung/clk-gs101.c b/drivers/clk/samsung/clk-gs101.c > index 27debbafdce4..7f6c3b52d9ff 100644 > --- a/drivers/clk/samsung/clk-gs101.c > +++ b/drivers/clk/samsung/clk-gs101.c > @@ -21,6 +21,7 @@ > #define CLKS_NR_APM (CLK_APM_PLL_DIV16_APM + 1) > #define CLKS_NR_MISC (CLK_GOUT_MISC_XIU_D_MISC_ACLK + 1) > #define CLKS_NR_PERIC0 (CLK_GOUT_PERIC0_SYSREG_PERIC0_PCLK + 1) > +#define CLKS_NR_PERIC1 (CLK_GOUT_PERIC1_SYSREG_PERIC1_PCLK + 1) > > /* ---- CMU_TOP ------------------------------------------------------------- */ > > @@ -3066,6 +3067,348 @@ static const struct samsung_cmu_info peric0_cmu_info __initconst = { > .clk_name = "bus", > }; > > +/* ---- CMU_PERIC1 ---------------------------------------------------------- */ > + > +/* Register Offset definitions for CMU_PERIC1 (0x10c00000) */ > +#define PLL_CON0_MUX_CLKCMU_PERIC1_BUS_USER 0x0600 > +#define PLL_CON1_MUX_CLKCMU_PERIC1_BUS_USER 0x0604 > +#define PLL_CON0_MUX_CLKCMU_PERIC1_I3C_USER 0x0610 > +#define PLL_CON1_MUX_CLKCMU_PERIC1_I3C_USER 0x0614 > +#define PLL_CON0_MUX_CLKCMU_PERIC1_USI0_USI_USER 0x0620 > +#define PLL_CON1_MUX_CLKCMU_PERIC1_USI0_USI_USER 0x0624 > +#define PLL_CON0_MUX_CLKCMU_PERIC1_USI10_USI_USER 0x0630 > +#define PLL_CON1_MUX_CLKCMU_PERIC1_USI10_USI_USER 0x0634 > +#define PLL_CON0_MUX_CLKCMU_PERIC1_USI11_USI_USER 0x0640 > +#define PLL_CON1_MUX_CLKCMU_PERIC1_USI11_USI_USER 0x0644 > +#define PLL_CON0_MUX_CLKCMU_PERIC1_USI12_USI_USER 0x0650 > +#define PLL_CON1_MUX_CLKCMU_PERIC1_USI12_USI_USER 0x0654 > +#define PLL_CON0_MUX_CLKCMU_PERIC1_USI13_USI_USER 0x0660 > +#define PLL_CON1_MUX_CLKCMU_PERIC1_USI13_USI_USER 0x0664 > +#define PLL_CON0_MUX_CLKCMU_PERIC1_USI9_USI_USER 0x0670 > +#define PLL_CON1_MUX_CLKCMU_PERIC1_USI9_USI_USER 0x0674 > +#define PERIC1_CMU_PERIC1_CONTROLLER_OPTION 0x0800 > +#define CLKOUT_CON_BLK_PERIC1_CMU_PERIC1_CLKOUT0 0x0810 > +#define CLK_CON_DIV_DIV_CLK_PERIC1_I3C 0x1800 > +#define CLK_CON_DIV_DIV_CLK_PERIC1_USI0_USI 0x1804 > +#define CLK_CON_DIV_DIV_CLK_PERIC1_USI10_USI 0x1808 > +#define CLK_CON_DIV_DIV_CLK_PERIC1_USI11_USI 0x180c > +#define CLK_CON_DIV_DIV_CLK_PERIC1_USI12_USI 0x1810 > +#define CLK_CON_DIV_DIV_CLK_PERIC1_USI13_USI 0x1814 > +#define CLK_CON_DIV_DIV_CLK_PERIC1_USI9_USI 0x1818 > +#define CLK_CON_BUF_CLKBUF_PERIC1_IP 0x2000 > +#define CLK_CON_GAT_CLK_BLK_PERIC1_UID_PERIC1_CMU_PERIC1_IPCLKPORT_PCLK 0x2004 > +#define CLK_CON_GAT_CLK_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_I3C_IPCLKPORT_CLK 0x2008 > +#define CLK_CON_GAT_CLK_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_OSCCLK_IPCLKPORT_CLK 0x200c > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_D_TZPC_PERIC1_IPCLKPORT_PCLK 0x2010 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_GPC_PERIC1_IPCLKPORT_PCLK 0x2014 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_GPIO_PERIC1_IPCLKPORT_PCLK 0x2018 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_LHM_AXI_P_PERIC1_IPCLKPORT_I_CLK 0x201c > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_1 0x2020 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_2 0x2024 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_3 0x2028 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_4 0x202c > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_5 0x2030 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_6 0x2034 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_8 0x2038 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_1 0x203c > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_15 0x2040 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_2 0x2044 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_3 0x2048 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_4 0x204c > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_5 0x2050 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_6 0x2054 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_8 0x2058 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_BUSP_IPCLKPORT_CLK 0x205c > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI0_USI_IPCLKPORT_CLK 0x2060 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI10_USI_IPCLKPORT_CLK 0x2064 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI11_USI_IPCLKPORT_CLK 0x2068 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI12_USI_IPCLKPORT_CLK 0x206c > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI13_USI_IPCLKPORT_CLK 0x2070 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI9_USI_IPCLKPORT_CLK 0x2074 > +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_SYSREG_PERIC1_IPCLKPORT_PCLK 0x2078 > +#define DMYQCH_CON_PERIC1_TOP0_QCH_S 0x3000 > +#define PCH_CON_LHM_AXI_P_PERIC1_PCH 0x3004 > +#define QCH_CON_D_TZPC_PERIC1_QCH 0x3008 > +#define QCH_CON_GPC_PERIC1_QCH 0x300c > +#define QCH_CON_GPIO_PERIC1_QCH 0x3010 > +#define QCH_CON_LHM_AXI_P_PERIC1_QCH 0x3014 > +#define QCH_CON_PERIC1_CMU_PERIC1_QCH 0x3018 > +#define QCH_CON_PERIC1_TOP0_QCH_I3C0 0x301c > +#define QCH_CON_PERIC1_TOP0_QCH_PWM 0x3020 > +#define QCH_CON_PERIC1_TOP0_QCH_USI0_USI 0x3024 > +#define QCH_CON_PERIC1_TOP0_QCH_USI10_USI 0x3028 > +#define QCH_CON_PERIC1_TOP0_QCH_USI11_USI 0x302c > +#define QCH_CON_PERIC1_TOP0_QCH_USI12_USI 0x3030 > +#define QCH_CON_PERIC1_TOP0_QCH_USI13_USI 0x3034 > +#define QCH_CON_PERIC1_TOP0_QCH_USI9_USI 0x3038 > +#define QCH_CON_SYSREG_PERIC1_QCH 0x303c > +#define QUEUE_CTRL_REG_BLK_PERIC1_CMU_PERIC1 0x3c00 > + > +static const unsigned long peric1_clk_regs[] __initconst = { > + PLL_CON0_MUX_CLKCMU_PERIC1_BUS_USER, > + PLL_CON1_MUX_CLKCMU_PERIC1_BUS_USER, > + PLL_CON0_MUX_CLKCMU_PERIC1_I3C_USER, > + PLL_CON1_MUX_CLKCMU_PERIC1_I3C_USER, > + PLL_CON0_MUX_CLKCMU_PERIC1_USI0_USI_USER, > + PLL_CON1_MUX_CLKCMU_PERIC1_USI0_USI_USER, > + PLL_CON0_MUX_CLKCMU_PERIC1_USI10_USI_USER, > + PLL_CON1_MUX_CLKCMU_PERIC1_USI10_USI_USER, > + PLL_CON0_MUX_CLKCMU_PERIC1_USI11_USI_USER, > + PLL_CON1_MUX_CLKCMU_PERIC1_USI11_USI_USER, > + PLL_CON0_MUX_CLKCMU_PERIC1_USI12_USI_USER, > + PLL_CON1_MUX_CLKCMU_PERIC1_USI12_USI_USER, > + PLL_CON0_MUX_CLKCMU_PERIC1_USI13_USI_USER, > + PLL_CON1_MUX_CLKCMU_PERIC1_USI13_USI_USER, > + PLL_CON0_MUX_CLKCMU_PERIC1_USI9_USI_USER, > + PLL_CON1_MUX_CLKCMU_PERIC1_USI9_USI_USER, > + PERIC1_CMU_PERIC1_CONTROLLER_OPTION, > + CLKOUT_CON_BLK_PERIC1_CMU_PERIC1_CLKOUT0, > + CLK_CON_DIV_DIV_CLK_PERIC1_I3C, > + CLK_CON_DIV_DIV_CLK_PERIC1_USI0_USI, > + CLK_CON_DIV_DIV_CLK_PERIC1_USI10_USI, > + CLK_CON_DIV_DIV_CLK_PERIC1_USI11_USI, > + CLK_CON_DIV_DIV_CLK_PERIC1_USI12_USI, > + CLK_CON_DIV_DIV_CLK_PERIC1_USI13_USI, > + CLK_CON_DIV_DIV_CLK_PERIC1_USI9_USI, > + CLK_CON_BUF_CLKBUF_PERIC1_IP, > + CLK_CON_GAT_CLK_BLK_PERIC1_UID_PERIC1_CMU_PERIC1_IPCLKPORT_PCLK, > + CLK_CON_GAT_CLK_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_I3C_IPCLKPORT_CLK, > + CLK_CON_GAT_CLK_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_OSCCLK_IPCLKPORT_CLK, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_D_TZPC_PERIC1_IPCLKPORT_PCLK, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_GPC_PERIC1_IPCLKPORT_PCLK, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_GPIO_PERIC1_IPCLKPORT_PCLK, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_LHM_AXI_P_PERIC1_IPCLKPORT_I_CLK, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_1, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_2, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_3, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_4, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_5, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_6, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_8, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_1, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_15, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_2, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_3, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_4, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_5, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_6, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_8, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_BUSP_IPCLKPORT_CLK, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI0_USI_IPCLKPORT_CLK, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI10_USI_IPCLKPORT_CLK, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI11_USI_IPCLKPORT_CLK, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI12_USI_IPCLKPORT_CLK, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI13_USI_IPCLKPORT_CLK, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI9_USI_IPCLKPORT_CLK, > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_SYSREG_PERIC1_IPCLKPORT_PCLK, > + DMYQCH_CON_PERIC1_TOP0_QCH_S, > + PCH_CON_LHM_AXI_P_PERIC1_PCH, > + QCH_CON_D_TZPC_PERIC1_QCH, > + QCH_CON_GPC_PERIC1_QCH, > + QCH_CON_GPIO_PERIC1_QCH, > + QCH_CON_LHM_AXI_P_PERIC1_QCH, > + QCH_CON_PERIC1_CMU_PERIC1_QCH, > + QCH_CON_PERIC1_TOP0_QCH_I3C0, > + QCH_CON_PERIC1_TOP0_QCH_PWM, > + QCH_CON_PERIC1_TOP0_QCH_USI0_USI, > + QCH_CON_PERIC1_TOP0_QCH_USI10_USI, > + QCH_CON_PERIC1_TOP0_QCH_USI11_USI, > + QCH_CON_PERIC1_TOP0_QCH_USI12_USI, > + QCH_CON_PERIC1_TOP0_QCH_USI13_USI, > + QCH_CON_PERIC1_TOP0_QCH_USI9_USI, > + QCH_CON_SYSREG_PERIC1_QCH, > + QUEUE_CTRL_REG_BLK_PERIC1_CMU_PERIC1, > +}; > + > +/* List of parent clocks for Muxes in CMU_PERIC1 */ > +PNAME(mout_peric1_bus_user_p) = { "oscclk", "dout_cmu_peric1_bus" }; > +PNAME(mout_peric1_nonbususer_p) = { "oscclk", "dout_cmu_peric1_ip" }; > + > +static const struct samsung_mux_clock peric1_mux_clks[] __initconst = { > + MUX(CLK_MOUT_PERIC1_BUS_USER, "mout_peric1_bus_user", > + mout_peric1_bus_user_p, PLL_CON0_MUX_CLKCMU_PERIC1_BUS_USER, 4, 1), > + MUX(CLK_MOUT_PERIC1_I3C_USER, > + "mout_peric1_i3c_user", mout_peric1_nonbususer_p, > + PLL_CON0_MUX_CLKCMU_PERIC1_I3C_USER, 4, 1), > + MUX(CLK_MOUT_PERIC1_USI0_USI_USER, > + "mout_peric1_usi0_usi_user", mout_peric1_nonbususer_p, > + PLL_CON0_MUX_CLKCMU_PERIC1_USI0_USI_USER, 4, 1), > + MUX(CLK_MOUT_PERIC1_USI10_USI_USER, > + "mout_peric1_usi10_usi_user", mout_peric1_nonbususer_p, > + PLL_CON0_MUX_CLKCMU_PERIC1_USI10_USI_USER, 4, 1), > + MUX(CLK_MOUT_PERIC1_USI11_USI_USER, > + "mout_peric1_usi11_usi_user", mout_peric1_nonbususer_p, > + PLL_CON0_MUX_CLKCMU_PERIC1_USI11_USI_USER, 4, 1), > + MUX(CLK_MOUT_PERIC1_USI12_USI_USER, > + "mout_peric1_usi12_usi_user", mout_peric1_nonbususer_p, > + PLL_CON0_MUX_CLKCMU_PERIC1_USI12_USI_USER, 4, 1), > + MUX(CLK_MOUT_PERIC1_USI13_USI_USER, > + "mout_peric1_usi13_usi_user", mout_peric1_nonbususer_p, > + PLL_CON0_MUX_CLKCMU_PERIC1_USI13_USI_USER, 4, 1), > + MUX(CLK_MOUT_PERIC1_USI9_USI_USER, > + "mout_peric1_usi9_usi_user", mout_peric1_nonbususer_p, > + PLL_CON0_MUX_CLKCMU_PERIC1_USI9_USI_USER, 4, 1), > +}; > + > +static const struct samsung_div_clock peric1_div_clks[] __initconst = { > + DIV(CLK_DOUT_PERIC1_I3C, "dout_peric1_i3c", "mout_peric1_i3c_user", > + CLK_CON_DIV_DIV_CLK_PERIC1_I3C, 0, 4), > + DIV(CLK_DOUT_PERIC1_USI0_USI, > + "dout_peric1_usi0_usi", "mout_peric1_usi0_usi_user", > + CLK_CON_DIV_DIV_CLK_PERIC1_USI0_USI, 0, 4), > + DIV(CLK_DOUT_PERIC1_USI10_USI, > + "dout_peric1_usi10_usi", "mout_peric1_usi10_usi_user", > + CLK_CON_DIV_DIV_CLK_PERIC1_USI10_USI, 0, 4), > + DIV(CLK_DOUT_PERIC1_USI11_USI, > + "dout_peric1_usi11_usi", "mout_peric1_usi11_usi_user", > + CLK_CON_DIV_DIV_CLK_PERIC1_USI11_USI, 0, 4), > + DIV(CLK_DOUT_PERIC1_USI12_USI, > + "dout_peric1_usi12_usi", "mout_peric1_usi12_usi_user", > + CLK_CON_DIV_DIV_CLK_PERIC1_USI12_USI, 0, 4), > + DIV(CLK_DOUT_PERIC1_USI13_USI, > + "dout_peric1_usi13_usi", "mout_peric1_usi13_usi_user", > + CLK_CON_DIV_DIV_CLK_PERIC1_USI13_USI, 0, 4), > + DIV(CLK_DOUT_PERIC1_USI9_USI, > + "dout_peric1_usi9_usi", "mout_peric1_usi9_usi_user", > + CLK_CON_DIV_DIV_CLK_PERIC1_USI9_USI, 0, 4), > +}; > + > +static const struct samsung_gate_clock peric1_gate_clks[] __initconst = { > + GATE(CLK_GOUT_PERIC1_PCLK, > + "gout_peric1_peric1_pclk", "mout_peric1_bus_user", > + CLK_CON_GAT_CLK_BLK_PERIC1_UID_PERIC1_CMU_PERIC1_IPCLKPORT_PCLK, > + 21, CLK_IS_CRITICAL, 0), > + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_I3C_CLK, > + "gout_peric1_clk_peric1_i3c_clk", "dout_peric1_i3c", > + CLK_CON_GAT_CLK_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_I3C_IPCLKPORT_CLK, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_OSCCLK_CLK, > + "gout_peric1_clk_peric1_oscclk_clk", "oscclk", > + CLK_CON_GAT_CLK_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_OSCCLK_IPCLKPORT_CLK, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_D_TZPC_PERIC1_PCLK, > + "gout_peric1_d_tzpc_peric1_pclk", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_D_TZPC_PERIC1_IPCLKPORT_PCLK, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_GPC_PERIC1_PCLK, > + "gout_peric1_gpc_peric1_pclk", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_GPC_PERIC1_IPCLKPORT_PCLK, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_GPIO_PERIC1_PCLK, > + "gout_peric1_gpio_peric1_pclk", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_GPIO_PERIC1_IPCLKPORT_PCLK, > + 21, CLK_IGNORE_UNUSED, 0), > + GATE(CLK_GOUT_PERIC1_LHM_AXI_P_PERIC1_I_CLK, > + "gout_peric1_lhm_axi_p_peric1_i_clk", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_LHM_AXI_P_PERIC1_IPCLKPORT_I_CLK, > + 21, CLK_IS_CRITICAL, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_1, > + "gout_peric1_peric1_top0_ipclk_1", "dout_peric1_usi0_usi", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_1, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_2, > + "gout_peric1_peric1_top0_ipclk_2", "dout_peric1_usi9_usi", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_2, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_3, > + "gout_peric1_peric1_top0_ipclk_3", "dout_peric1_usi10_usi", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_3, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_4, > + "gout_peric1_peric1_top0_ipclk_4", "dout_peric1_usi11_usi", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_4, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_5, > + "gout_peric1_peric1_top0_ipclk_5", "dout_peric1_usi12_usi", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_5, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_6, > + "gout_peric1_peric1_top0_ipclk_6", "dout_peric1_usi13_usi", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_6, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_8, > + "gout_peric1_peric1_top0_ipclk_8", "dout_peric1_i3c", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_8, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_1, > + "gout_peric1_peric1_top0_pclk_1", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_1, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_15, > + "gout_peric1_peric1_top0_pclk_15", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_15, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_2, > + "gout_peric1_peric1_top0_pclk_2", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_2, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_3, > + "gout_peric1_peric1_top0_pclk_3", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_3, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_4, > + "gout_peric1_peric1_top0_pclk_4", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_4, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_5, > + "gout_peric1_peric1_top0_pclk_5", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_5, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_6, > + "gout_peric1_peric1_top0_pclk_6", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_6, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_8, > + "gout_peric1_peric1_top0_pclk_8", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_8, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_BUSP_CLK, > + "gout_peric1_clk_peric1_busp_clk", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_BUSP_IPCLKPORT_CLK, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_USI0_USI_CLK, > + "gout_peric1_clk_peric1_usi0_usi_clk", "dout_peric1_usi0_usi", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI0_USI_IPCLKPORT_CLK, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_USI10_USI_CLK, > + "gout_peric1_clk_peric1_usi10_usi_clk", "dout_peric1_usi10_usi", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI10_USI_IPCLKPORT_CLK, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_USI11_USI_CLK, > + "gout_peric1_clk_peric1_usi11_usi_clk", "dout_peric1_usi11_usi", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI11_USI_IPCLKPORT_CLK, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_USI12_USI_CLK, > + "gout_peric1_clk_peric1_usi12_usi_clk", "dout_peric1_usi12_usi", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI12_USI_IPCLKPORT_CLK, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_USI13_USI_CLK, > + "gout_peric1_clk_peric1_usi13_usi_clk", "dout_peric1_usi13_usi", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI13_USI_IPCLKPORT_CLK, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_USI9_USI_CLK, > + "gout_peric1_clk_peric1_usi9_usi_clk", "dout_peric1_usi9_usi", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI9_USI_IPCLKPORT_CLK, > + 21, 0, 0), > + GATE(CLK_GOUT_PERIC1_SYSREG_PERIC1_PCLK, > + "gout_peric1_sysreg_peric1_pclk", "mout_peric1_bus_user", > + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_SYSREG_PERIC1_IPCLKPORT_PCLK, > + 21, CLK_IGNORE_UNUSED, 0), > +}; > + > +static const struct samsung_cmu_info peric1_cmu_info __initconst = { > + .mux_clks = peric1_mux_clks, > + .nr_mux_clks = ARRAY_SIZE(peric1_mux_clks), > + .div_clks = peric1_div_clks, > + .nr_div_clks = ARRAY_SIZE(peric1_div_clks), > + .gate_clks = peric1_gate_clks, > + .nr_gate_clks = ARRAY_SIZE(peric1_gate_clks), > + .nr_clk_ids = CLKS_NR_PERIC1, > + .clk_regs = peric1_clk_regs, > + .nr_clk_regs = ARRAY_SIZE(peric1_clk_regs), > + .clk_name = "bus", > +}; > + > /* ---- platform_driver ----------------------------------------------------- */ > > static int __init gs101_cmu_probe(struct platform_device *pdev) > @@ -3086,6 +3429,9 @@ static const struct of_device_id gs101_cmu_of_match[] = { > }, { > .compatible = "google,gs101-cmu-peric0", > .data = &peric0_cmu_info, > + }, { > + .compatible = "google,gs101-cmu-peric1", > + .data = &peric1_cmu_info, > }, { > }, > }; > -- > 2.43.0.429.g432eaa2c6b-goog >
On Sat, 27 Jan 2024 at 00:19, André Draszik <andre.draszik@linaro.org> wrote: > > CMU_PERIC1 is the clock management unit used for the peric1 block which > is used for additional USI, I3C and PWM interfaces/busses. Add support > for muxes, dividers and gates of cmu_peric1, except for > CLK_GOUT_PERIC1_IP which isn't well described in the datasheet and > which downstream also ignores (similar to cmu_peric0). > > Two clocks have been marked as CLK_IS_CRITICAL for the following > reason: > * disabling them makes it impossible to access any peric1 > registers, (including those two registers). > * disabling gout_peric1_lhm_axi_p_peric1_i_clk sometimes has the > additional effect of making the whole system unresponsive. > > The clocks marked as CLK_IGNORE_UNUSED need to be kept on until we have > updated the respective drivers for the following reasons: > * gout_peric1_gpio_peric1_pclk is required by the pinctrl > configuration. With this clock disabled, reconfiguring the pins > (for USI/I2C, USI/UART) will hang during register access. > Since pingctrl-samsung doesn't support a clock at the moment, we > just keep the kernel from disabling it at boot, until we have an > update for samsung-pinctrl, at which point we'll drop the flag. > * gout_peric1_sysreg_peric1_pclk needs to be hooked up to > sysreg_peric1 in DT which will be done in a followup-patch, at > which point we'll drop the special treatment from here. We're > adding the flag temporarily here so as to not break the boot (due > to pclk otherwise getting disabled). > > Signed-off-by: André Draszik <andre.draszik@linaro.org> > > --- Thankyou for being verbose on this reasoning behind CLK_IGNORE_UNUSED and CLK_IS_CRITICAL flags Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Hi, Andre', I played with SPI and noticed that we have to propagate some clock rates to parents here. If you don't play with all the peripherals from the block you can't know what to propagate. So I think it's fine to not handle this topic right now. I'll come with a patch on top of yours when I finish the SPI validation. The patch is looking fine. I'll finish reviewing the series after v2 is out. Cheers, ta
diff --git a/drivers/clk/samsung/clk-gs101.c b/drivers/clk/samsung/clk-gs101.c index 27debbafdce4..7f6c3b52d9ff 100644 --- a/drivers/clk/samsung/clk-gs101.c +++ b/drivers/clk/samsung/clk-gs101.c @@ -21,6 +21,7 @@ #define CLKS_NR_APM (CLK_APM_PLL_DIV16_APM + 1) #define CLKS_NR_MISC (CLK_GOUT_MISC_XIU_D_MISC_ACLK + 1) #define CLKS_NR_PERIC0 (CLK_GOUT_PERIC0_SYSREG_PERIC0_PCLK + 1) +#define CLKS_NR_PERIC1 (CLK_GOUT_PERIC1_SYSREG_PERIC1_PCLK + 1) /* ---- CMU_TOP ------------------------------------------------------------- */ @@ -3066,6 +3067,348 @@ static const struct samsung_cmu_info peric0_cmu_info __initconst = { .clk_name = "bus", }; +/* ---- CMU_PERIC1 ---------------------------------------------------------- */ + +/* Register Offset definitions for CMU_PERIC1 (0x10c00000) */ +#define PLL_CON0_MUX_CLKCMU_PERIC1_BUS_USER 0x0600 +#define PLL_CON1_MUX_CLKCMU_PERIC1_BUS_USER 0x0604 +#define PLL_CON0_MUX_CLKCMU_PERIC1_I3C_USER 0x0610 +#define PLL_CON1_MUX_CLKCMU_PERIC1_I3C_USER 0x0614 +#define PLL_CON0_MUX_CLKCMU_PERIC1_USI0_USI_USER 0x0620 +#define PLL_CON1_MUX_CLKCMU_PERIC1_USI0_USI_USER 0x0624 +#define PLL_CON0_MUX_CLKCMU_PERIC1_USI10_USI_USER 0x0630 +#define PLL_CON1_MUX_CLKCMU_PERIC1_USI10_USI_USER 0x0634 +#define PLL_CON0_MUX_CLKCMU_PERIC1_USI11_USI_USER 0x0640 +#define PLL_CON1_MUX_CLKCMU_PERIC1_USI11_USI_USER 0x0644 +#define PLL_CON0_MUX_CLKCMU_PERIC1_USI12_USI_USER 0x0650 +#define PLL_CON1_MUX_CLKCMU_PERIC1_USI12_USI_USER 0x0654 +#define PLL_CON0_MUX_CLKCMU_PERIC1_USI13_USI_USER 0x0660 +#define PLL_CON1_MUX_CLKCMU_PERIC1_USI13_USI_USER 0x0664 +#define PLL_CON0_MUX_CLKCMU_PERIC1_USI9_USI_USER 0x0670 +#define PLL_CON1_MUX_CLKCMU_PERIC1_USI9_USI_USER 0x0674 +#define PERIC1_CMU_PERIC1_CONTROLLER_OPTION 0x0800 +#define CLKOUT_CON_BLK_PERIC1_CMU_PERIC1_CLKOUT0 0x0810 +#define CLK_CON_DIV_DIV_CLK_PERIC1_I3C 0x1800 +#define CLK_CON_DIV_DIV_CLK_PERIC1_USI0_USI 0x1804 +#define CLK_CON_DIV_DIV_CLK_PERIC1_USI10_USI 0x1808 +#define CLK_CON_DIV_DIV_CLK_PERIC1_USI11_USI 0x180c +#define CLK_CON_DIV_DIV_CLK_PERIC1_USI12_USI 0x1810 +#define CLK_CON_DIV_DIV_CLK_PERIC1_USI13_USI 0x1814 +#define CLK_CON_DIV_DIV_CLK_PERIC1_USI9_USI 0x1818 +#define CLK_CON_BUF_CLKBUF_PERIC1_IP 0x2000 +#define CLK_CON_GAT_CLK_BLK_PERIC1_UID_PERIC1_CMU_PERIC1_IPCLKPORT_PCLK 0x2004 +#define CLK_CON_GAT_CLK_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_I3C_IPCLKPORT_CLK 0x2008 +#define CLK_CON_GAT_CLK_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_OSCCLK_IPCLKPORT_CLK 0x200c +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_D_TZPC_PERIC1_IPCLKPORT_PCLK 0x2010 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_GPC_PERIC1_IPCLKPORT_PCLK 0x2014 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_GPIO_PERIC1_IPCLKPORT_PCLK 0x2018 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_LHM_AXI_P_PERIC1_IPCLKPORT_I_CLK 0x201c +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_1 0x2020 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_2 0x2024 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_3 0x2028 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_4 0x202c +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_5 0x2030 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_6 0x2034 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_8 0x2038 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_1 0x203c +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_15 0x2040 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_2 0x2044 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_3 0x2048 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_4 0x204c +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_5 0x2050 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_6 0x2054 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_8 0x2058 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_BUSP_IPCLKPORT_CLK 0x205c +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI0_USI_IPCLKPORT_CLK 0x2060 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI10_USI_IPCLKPORT_CLK 0x2064 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI11_USI_IPCLKPORT_CLK 0x2068 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI12_USI_IPCLKPORT_CLK 0x206c +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI13_USI_IPCLKPORT_CLK 0x2070 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI9_USI_IPCLKPORT_CLK 0x2074 +#define CLK_CON_GAT_GOUT_BLK_PERIC1_UID_SYSREG_PERIC1_IPCLKPORT_PCLK 0x2078 +#define DMYQCH_CON_PERIC1_TOP0_QCH_S 0x3000 +#define PCH_CON_LHM_AXI_P_PERIC1_PCH 0x3004 +#define QCH_CON_D_TZPC_PERIC1_QCH 0x3008 +#define QCH_CON_GPC_PERIC1_QCH 0x300c +#define QCH_CON_GPIO_PERIC1_QCH 0x3010 +#define QCH_CON_LHM_AXI_P_PERIC1_QCH 0x3014 +#define QCH_CON_PERIC1_CMU_PERIC1_QCH 0x3018 +#define QCH_CON_PERIC1_TOP0_QCH_I3C0 0x301c +#define QCH_CON_PERIC1_TOP0_QCH_PWM 0x3020 +#define QCH_CON_PERIC1_TOP0_QCH_USI0_USI 0x3024 +#define QCH_CON_PERIC1_TOP0_QCH_USI10_USI 0x3028 +#define QCH_CON_PERIC1_TOP0_QCH_USI11_USI 0x302c +#define QCH_CON_PERIC1_TOP0_QCH_USI12_USI 0x3030 +#define QCH_CON_PERIC1_TOP0_QCH_USI13_USI 0x3034 +#define QCH_CON_PERIC1_TOP0_QCH_USI9_USI 0x3038 +#define QCH_CON_SYSREG_PERIC1_QCH 0x303c +#define QUEUE_CTRL_REG_BLK_PERIC1_CMU_PERIC1 0x3c00 + +static const unsigned long peric1_clk_regs[] __initconst = { + PLL_CON0_MUX_CLKCMU_PERIC1_BUS_USER, + PLL_CON1_MUX_CLKCMU_PERIC1_BUS_USER, + PLL_CON0_MUX_CLKCMU_PERIC1_I3C_USER, + PLL_CON1_MUX_CLKCMU_PERIC1_I3C_USER, + PLL_CON0_MUX_CLKCMU_PERIC1_USI0_USI_USER, + PLL_CON1_MUX_CLKCMU_PERIC1_USI0_USI_USER, + PLL_CON0_MUX_CLKCMU_PERIC1_USI10_USI_USER, + PLL_CON1_MUX_CLKCMU_PERIC1_USI10_USI_USER, + PLL_CON0_MUX_CLKCMU_PERIC1_USI11_USI_USER, + PLL_CON1_MUX_CLKCMU_PERIC1_USI11_USI_USER, + PLL_CON0_MUX_CLKCMU_PERIC1_USI12_USI_USER, + PLL_CON1_MUX_CLKCMU_PERIC1_USI12_USI_USER, + PLL_CON0_MUX_CLKCMU_PERIC1_USI13_USI_USER, + PLL_CON1_MUX_CLKCMU_PERIC1_USI13_USI_USER, + PLL_CON0_MUX_CLKCMU_PERIC1_USI9_USI_USER, + PLL_CON1_MUX_CLKCMU_PERIC1_USI9_USI_USER, + PERIC1_CMU_PERIC1_CONTROLLER_OPTION, + CLKOUT_CON_BLK_PERIC1_CMU_PERIC1_CLKOUT0, + CLK_CON_DIV_DIV_CLK_PERIC1_I3C, + CLK_CON_DIV_DIV_CLK_PERIC1_USI0_USI, + CLK_CON_DIV_DIV_CLK_PERIC1_USI10_USI, + CLK_CON_DIV_DIV_CLK_PERIC1_USI11_USI, + CLK_CON_DIV_DIV_CLK_PERIC1_USI12_USI, + CLK_CON_DIV_DIV_CLK_PERIC1_USI13_USI, + CLK_CON_DIV_DIV_CLK_PERIC1_USI9_USI, + CLK_CON_BUF_CLKBUF_PERIC1_IP, + CLK_CON_GAT_CLK_BLK_PERIC1_UID_PERIC1_CMU_PERIC1_IPCLKPORT_PCLK, + CLK_CON_GAT_CLK_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_I3C_IPCLKPORT_CLK, + CLK_CON_GAT_CLK_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_OSCCLK_IPCLKPORT_CLK, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_D_TZPC_PERIC1_IPCLKPORT_PCLK, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_GPC_PERIC1_IPCLKPORT_PCLK, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_GPIO_PERIC1_IPCLKPORT_PCLK, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_LHM_AXI_P_PERIC1_IPCLKPORT_I_CLK, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_1, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_2, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_3, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_4, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_5, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_6, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_8, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_1, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_15, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_2, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_3, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_4, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_5, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_6, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_8, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_BUSP_IPCLKPORT_CLK, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI0_USI_IPCLKPORT_CLK, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI10_USI_IPCLKPORT_CLK, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI11_USI_IPCLKPORT_CLK, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI12_USI_IPCLKPORT_CLK, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI13_USI_IPCLKPORT_CLK, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI9_USI_IPCLKPORT_CLK, + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_SYSREG_PERIC1_IPCLKPORT_PCLK, + DMYQCH_CON_PERIC1_TOP0_QCH_S, + PCH_CON_LHM_AXI_P_PERIC1_PCH, + QCH_CON_D_TZPC_PERIC1_QCH, + QCH_CON_GPC_PERIC1_QCH, + QCH_CON_GPIO_PERIC1_QCH, + QCH_CON_LHM_AXI_P_PERIC1_QCH, + QCH_CON_PERIC1_CMU_PERIC1_QCH, + QCH_CON_PERIC1_TOP0_QCH_I3C0, + QCH_CON_PERIC1_TOP0_QCH_PWM, + QCH_CON_PERIC1_TOP0_QCH_USI0_USI, + QCH_CON_PERIC1_TOP0_QCH_USI10_USI, + QCH_CON_PERIC1_TOP0_QCH_USI11_USI, + QCH_CON_PERIC1_TOP0_QCH_USI12_USI, + QCH_CON_PERIC1_TOP0_QCH_USI13_USI, + QCH_CON_PERIC1_TOP0_QCH_USI9_USI, + QCH_CON_SYSREG_PERIC1_QCH, + QUEUE_CTRL_REG_BLK_PERIC1_CMU_PERIC1, +}; + +/* List of parent clocks for Muxes in CMU_PERIC1 */ +PNAME(mout_peric1_bus_user_p) = { "oscclk", "dout_cmu_peric1_bus" }; +PNAME(mout_peric1_nonbususer_p) = { "oscclk", "dout_cmu_peric1_ip" }; + +static const struct samsung_mux_clock peric1_mux_clks[] __initconst = { + MUX(CLK_MOUT_PERIC1_BUS_USER, "mout_peric1_bus_user", + mout_peric1_bus_user_p, PLL_CON0_MUX_CLKCMU_PERIC1_BUS_USER, 4, 1), + MUX(CLK_MOUT_PERIC1_I3C_USER, + "mout_peric1_i3c_user", mout_peric1_nonbususer_p, + PLL_CON0_MUX_CLKCMU_PERIC1_I3C_USER, 4, 1), + MUX(CLK_MOUT_PERIC1_USI0_USI_USER, + "mout_peric1_usi0_usi_user", mout_peric1_nonbususer_p, + PLL_CON0_MUX_CLKCMU_PERIC1_USI0_USI_USER, 4, 1), + MUX(CLK_MOUT_PERIC1_USI10_USI_USER, + "mout_peric1_usi10_usi_user", mout_peric1_nonbususer_p, + PLL_CON0_MUX_CLKCMU_PERIC1_USI10_USI_USER, 4, 1), + MUX(CLK_MOUT_PERIC1_USI11_USI_USER, + "mout_peric1_usi11_usi_user", mout_peric1_nonbususer_p, + PLL_CON0_MUX_CLKCMU_PERIC1_USI11_USI_USER, 4, 1), + MUX(CLK_MOUT_PERIC1_USI12_USI_USER, + "mout_peric1_usi12_usi_user", mout_peric1_nonbususer_p, + PLL_CON0_MUX_CLKCMU_PERIC1_USI12_USI_USER, 4, 1), + MUX(CLK_MOUT_PERIC1_USI13_USI_USER, + "mout_peric1_usi13_usi_user", mout_peric1_nonbususer_p, + PLL_CON0_MUX_CLKCMU_PERIC1_USI13_USI_USER, 4, 1), + MUX(CLK_MOUT_PERIC1_USI9_USI_USER, + "mout_peric1_usi9_usi_user", mout_peric1_nonbususer_p, + PLL_CON0_MUX_CLKCMU_PERIC1_USI9_USI_USER, 4, 1), +}; + +static const struct samsung_div_clock peric1_div_clks[] __initconst = { + DIV(CLK_DOUT_PERIC1_I3C, "dout_peric1_i3c", "mout_peric1_i3c_user", + CLK_CON_DIV_DIV_CLK_PERIC1_I3C, 0, 4), + DIV(CLK_DOUT_PERIC1_USI0_USI, + "dout_peric1_usi0_usi", "mout_peric1_usi0_usi_user", + CLK_CON_DIV_DIV_CLK_PERIC1_USI0_USI, 0, 4), + DIV(CLK_DOUT_PERIC1_USI10_USI, + "dout_peric1_usi10_usi", "mout_peric1_usi10_usi_user", + CLK_CON_DIV_DIV_CLK_PERIC1_USI10_USI, 0, 4), + DIV(CLK_DOUT_PERIC1_USI11_USI, + "dout_peric1_usi11_usi", "mout_peric1_usi11_usi_user", + CLK_CON_DIV_DIV_CLK_PERIC1_USI11_USI, 0, 4), + DIV(CLK_DOUT_PERIC1_USI12_USI, + "dout_peric1_usi12_usi", "mout_peric1_usi12_usi_user", + CLK_CON_DIV_DIV_CLK_PERIC1_USI12_USI, 0, 4), + DIV(CLK_DOUT_PERIC1_USI13_USI, + "dout_peric1_usi13_usi", "mout_peric1_usi13_usi_user", + CLK_CON_DIV_DIV_CLK_PERIC1_USI13_USI, 0, 4), + DIV(CLK_DOUT_PERIC1_USI9_USI, + "dout_peric1_usi9_usi", "mout_peric1_usi9_usi_user", + CLK_CON_DIV_DIV_CLK_PERIC1_USI9_USI, 0, 4), +}; + +static const struct samsung_gate_clock peric1_gate_clks[] __initconst = { + GATE(CLK_GOUT_PERIC1_PCLK, + "gout_peric1_peric1_pclk", "mout_peric1_bus_user", + CLK_CON_GAT_CLK_BLK_PERIC1_UID_PERIC1_CMU_PERIC1_IPCLKPORT_PCLK, + 21, CLK_IS_CRITICAL, 0), + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_I3C_CLK, + "gout_peric1_clk_peric1_i3c_clk", "dout_peric1_i3c", + CLK_CON_GAT_CLK_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_I3C_IPCLKPORT_CLK, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_OSCCLK_CLK, + "gout_peric1_clk_peric1_oscclk_clk", "oscclk", + CLK_CON_GAT_CLK_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_OSCCLK_IPCLKPORT_CLK, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_D_TZPC_PERIC1_PCLK, + "gout_peric1_d_tzpc_peric1_pclk", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_D_TZPC_PERIC1_IPCLKPORT_PCLK, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_GPC_PERIC1_PCLK, + "gout_peric1_gpc_peric1_pclk", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_GPC_PERIC1_IPCLKPORT_PCLK, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_GPIO_PERIC1_PCLK, + "gout_peric1_gpio_peric1_pclk", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_GPIO_PERIC1_IPCLKPORT_PCLK, + 21, CLK_IGNORE_UNUSED, 0), + GATE(CLK_GOUT_PERIC1_LHM_AXI_P_PERIC1_I_CLK, + "gout_peric1_lhm_axi_p_peric1_i_clk", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_LHM_AXI_P_PERIC1_IPCLKPORT_I_CLK, + 21, CLK_IS_CRITICAL, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_1, + "gout_peric1_peric1_top0_ipclk_1", "dout_peric1_usi0_usi", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_1, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_2, + "gout_peric1_peric1_top0_ipclk_2", "dout_peric1_usi9_usi", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_2, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_3, + "gout_peric1_peric1_top0_ipclk_3", "dout_peric1_usi10_usi", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_3, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_4, + "gout_peric1_peric1_top0_ipclk_4", "dout_peric1_usi11_usi", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_4, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_5, + "gout_peric1_peric1_top0_ipclk_5", "dout_peric1_usi12_usi", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_5, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_6, + "gout_peric1_peric1_top0_ipclk_6", "dout_peric1_usi13_usi", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_6, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_IPCLK_8, + "gout_peric1_peric1_top0_ipclk_8", "dout_peric1_i3c", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_IPCLK_8, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_1, + "gout_peric1_peric1_top0_pclk_1", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_1, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_15, + "gout_peric1_peric1_top0_pclk_15", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_15, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_2, + "gout_peric1_peric1_top0_pclk_2", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_2, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_3, + "gout_peric1_peric1_top0_pclk_3", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_3, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_4, + "gout_peric1_peric1_top0_pclk_4", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_4, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_5, + "gout_peric1_peric1_top0_pclk_5", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_5, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_6, + "gout_peric1_peric1_top0_pclk_6", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_6, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_PERIC1_TOP0_PCLK_8, + "gout_peric1_peric1_top0_pclk_8", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_PERIC1_TOP0_IPCLKPORT_PCLK_8, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_BUSP_CLK, + "gout_peric1_clk_peric1_busp_clk", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_BUSP_IPCLKPORT_CLK, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_USI0_USI_CLK, + "gout_peric1_clk_peric1_usi0_usi_clk", "dout_peric1_usi0_usi", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI0_USI_IPCLKPORT_CLK, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_USI10_USI_CLK, + "gout_peric1_clk_peric1_usi10_usi_clk", "dout_peric1_usi10_usi", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI10_USI_IPCLKPORT_CLK, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_USI11_USI_CLK, + "gout_peric1_clk_peric1_usi11_usi_clk", "dout_peric1_usi11_usi", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI11_USI_IPCLKPORT_CLK, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_USI12_USI_CLK, + "gout_peric1_clk_peric1_usi12_usi_clk", "dout_peric1_usi12_usi", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI12_USI_IPCLKPORT_CLK, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_USI13_USI_CLK, + "gout_peric1_clk_peric1_usi13_usi_clk", "dout_peric1_usi13_usi", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI13_USI_IPCLKPORT_CLK, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_CLK_PERIC1_USI9_USI_CLK, + "gout_peric1_clk_peric1_usi9_usi_clk", "dout_peric1_usi9_usi", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_RSTNSYNC_CLK_PERIC1_USI9_USI_IPCLKPORT_CLK, + 21, 0, 0), + GATE(CLK_GOUT_PERIC1_SYSREG_PERIC1_PCLK, + "gout_peric1_sysreg_peric1_pclk", "mout_peric1_bus_user", + CLK_CON_GAT_GOUT_BLK_PERIC1_UID_SYSREG_PERIC1_IPCLKPORT_PCLK, + 21, CLK_IGNORE_UNUSED, 0), +}; + +static const struct samsung_cmu_info peric1_cmu_info __initconst = { + .mux_clks = peric1_mux_clks, + .nr_mux_clks = ARRAY_SIZE(peric1_mux_clks), + .div_clks = peric1_div_clks, + .nr_div_clks = ARRAY_SIZE(peric1_div_clks), + .gate_clks = peric1_gate_clks, + .nr_gate_clks = ARRAY_SIZE(peric1_gate_clks), + .nr_clk_ids = CLKS_NR_PERIC1, + .clk_regs = peric1_clk_regs, + .nr_clk_regs = ARRAY_SIZE(peric1_clk_regs), + .clk_name = "bus", +}; + /* ---- platform_driver ----------------------------------------------------- */ static int __init gs101_cmu_probe(struct platform_device *pdev) @@ -3086,6 +3429,9 @@ static const struct of_device_id gs101_cmu_of_match[] = { }, { .compatible = "google,gs101-cmu-peric0", .data = &peric0_cmu_info, + }, { + .compatible = "google,gs101-cmu-peric1", + .data = &peric1_cmu_info, }, { }, };
CMU_PERIC1 is the clock management unit used for the peric1 block which is used for additional USI, I3C and PWM interfaces/busses. Add support for muxes, dividers and gates of cmu_peric1, except for CLK_GOUT_PERIC1_IP which isn't well described in the datasheet and which downstream also ignores (similar to cmu_peric0). Two clocks have been marked as CLK_IS_CRITICAL for the following reason: * disabling them makes it impossible to access any peric1 registers, (including those two registers). * disabling gout_peric1_lhm_axi_p_peric1_i_clk sometimes has the additional effect of making the whole system unresponsive. The clocks marked as CLK_IGNORE_UNUSED need to be kept on until we have updated the respective drivers for the following reasons: * gout_peric1_gpio_peric1_pclk is required by the pinctrl configuration. With this clock disabled, reconfiguring the pins (for USI/I2C, USI/UART) will hang during register access. Since pingctrl-samsung doesn't support a clock at the moment, we just keep the kernel from disabling it at boot, until we have an update for samsung-pinctrl, at which point we'll drop the flag. * gout_peric1_sysreg_peric1_pclk needs to be hooked up to sysreg_peric1 in DT which will be done in a followup-patch, at which point we'll drop the special treatment from here. We're adding the flag temporarily here so as to not break the boot (due to pclk otherwise getting disabled). Signed-off-by: André Draszik <andre.draszik@linaro.org> --- Note for future reference: To ensure consistent naming throughout this driver, the clock names have been derived from the data sheet using the following, with the expectation for all future additions to this file to use the same: sed \ -e 's|^PLL_LOCKTIME_PLL_\([^_]\+\)|fout_\L\1_pll|' \ \ -e 's|^PLL_CON0_MUX_CLKCMU_\([^_]\+\)_\(.*\)|mout_\L\1_\2|' \ -e 's|^PLL_CON0_PLL_\(.*\)|mout_pll_\L\1|' \ -e 's|^CLK_CON_MUX_MUX_CLK_\(.*\)|mout_\L\1|' \ -e '/^PLL_CON[1-4]_[^_]\+_/d' \ -e '/^[^_]\+_CMU_[^_]\+_CONTROLLER_OPTION/d' \ -e '/^CLKOUT_CON_BLK_[^_]\+_CMU_[^_]\+_CLKOUT0/d' \ \ -e 's|_IPCLKPORT||' \ -e 's|_RSTNSYNC||' \ \ -e 's|^CLK_CON_DIV_DIV_CLK_\([^_]\+\)_\(.*\)|dout_\L\1_\2|' \ \ -e 's|^CLK_CON_BUF_CLKBUF_\([^_]\+\)_\(.*\)|gout_\L\1_\2|' \ -e 's|^CLK_CON_GAT_CLK_BLK_\([^_]\+\)_UID_\(.*\)|gout_\L\1_\2|' \ -e 's|^gout_[^_]\+_[^_]\+_cmu_\([^_]\+\)_pclk$|gout_\1_\1_pclk|' \ -e 's|^CLK_CON_GAT_GOUT_BLK_\([^_]\+\)_UID_\(.*\)|gout_\L\1_\2|' \ -e 's|^CLK_CON_GAT_CLK_\([^_]\+\)_\(.*\)|gout_\L\1_clk_\L\1_\2|' \ \ -e '/^\(DMYQCH\|PCH\|QCH\|QUEUE\)_/d' --- drivers/clk/samsung/clk-gs101.c | 346 ++++++++++++++++++++++++++++++++ 1 file changed, 346 insertions(+)