@@ -159,6 +159,7 @@ Hardware Monitoring Kernel Drivers
mp2888
mp2975
mp5023
+ msi-psu
nct6683
nct6775
nct7802
new file mode 100644
@@ -0,0 +1,64 @@
+.. SPDX-License-Identifier: GPL-2.0-or-later
+
+Kernel driver msi-psu
+=========================
+
+Supported devices:
+
+* MSI MEG Ai1300P
+
+* MSI MEG Ai1000P
+
+Author: Jack Doan
+
+Description
+-----------
+
+This driver provides a sysfs interface for MSI PSUs with a HID monitoring
+interface.
+
+Measurements for the output voltage and current for each rail are provided,
+as well as total output power, temperature, and fan control.
+
+Additional properties are available in debugfs, such as an efficiency
+measurement, and switching to/from 12V multi-rail mode
+
+Sysfs entries
+-------------
+
+============ ===============================================================
+curr1_input Current on the 12v psu rail
+curr2_input Current on the 5v psu rail
+curr3_input Current on the 3.3v psu rail
+fan1_input RPM of psu fan
+in0_input Voltage of the psu ac input
+in1_input Voltage of the 12v psu rail
+in2_input Voltage of the 5v psu rail
+in3_input Voltage of the 3.3v psu rail
+power1_input Total power usage
+pwm1 PWM value for fan1. Writes to this file will switch set
+ pwm1_enable to manual control mode.
+pwm1_enable PWM mode for fan1. (1) means "auto", and uses the built-in fan
+ curve. (3) means manual control
+temp1_input Temperature of the psu
+============ ===============================================================
+
+Usage Notes
+-----------
+
+It is an USB HID device, so it is auto-detected, supports hot-swapping and
+several devices at once.
+
+Debugfs entries
+---------------
+
+==================== ========================================================
+multi_rail_enabled Single or multi rail mode of the PCIe power connectors
+efficiency An efficiency measurement, expressed as per-ten-thousand
+ (ex: 8512 == 85.12%)
+product Product name of the psu
+revision Revision number of the psu
+uptime Session uptime of the psu
+uptime_total Total uptime of the psu
+vendor Vendor name of the psu
+==================== ========================================================
@@ -14632,6 +14632,13 @@ L: platform-driver-x86@vger.kernel.org
S: Maintained
F: drivers/platform/x86/msi-laptop.c
+MSI PSU HARDWARE MONITOR DRIVER
+M: Jack Doan <me@jackdoan.com>
+L: linux-hwmon@vger.kernel.org
+S: Maintained
+F: Documentation/hwmon/msi-psu.rst
+F: drivers/hwmon/msi-psu.c
+
MSI WMI SUPPORT
L: platform-driver-x86@vger.kernel.org
S: Orphan
@@ -1248,6 +1248,18 @@ config SENSORS_MLXREG_FAN
driver as a module, choose 'M' here: the module will be called
mlxreg-fan.
+config SENSORS_MSI_PSU
+ tristate "MSI PSU HID controller"
+ depends on HID
+ help
+ If you say yes here you get support for MSI power supplies with an
+ HID monitoring interface.
+
+ Currently this driver supports the MEG Ai1300P and MEG Ai1000P PSUs.
+
+ This driver can also be built as a module. If so, the module
+ will be called msi-psu.
+
config SENSORS_TC654
tristate "Microchip TC654/TC655 and compatibles"
depends on I2C
@@ -156,6 +156,7 @@ obj-$(CONFIG_MAX31827) += max31827.o
obj-$(CONFIG_SENSORS_MC13783_ADC)+= mc13783-adc.o
obj-$(CONFIG_SENSORS_MC34VR500) += mc34vr500.o
obj-$(CONFIG_SENSORS_MCP3021) += mcp3021.o
+obj-$(CONFIG_SENSORS_MSI_PSU) += msi-psu.o
obj-$(CONFIG_SENSORS_TC654) += tc654.o
obj-$(CONFIG_SENSORS_TPS23861) += tps23861.o
obj-$(CONFIG_SENSORS_MLXREG_FAN) += mlxreg-fan.o
new file mode 100644
@@ -0,0 +1,801 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Driver for MSI power supplies with USB-HID interfaces
+ * Heavily derived from the corsair-psu and corsair-cpro drivers,
+ * but different enough to be incompatible
+ *
+ * Copyright (C) 2023 Jack Doan <me@jackdoan.com>
+ */
+
+#include <linux/completion.h>
+#include <linux/debugfs.h>
+#include <linux/errno.h>
+#include <linux/hid.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/jiffies.h>
+#include <linux/minmax.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+/*
+ * MSI protocol for PSUs
+ *
+ * message size = 64 bytes (request and response, little endian)
+ * request:
+ * [command][register][param0][param1][paramX]...
+ * reply:
+ * [echo of command][echo of register][data0][data1][dataX]...
+ *
+ * - the driver uses raw events to be accessible from userspace (though this is not really
+ * supported, it is just there for convenience, may be removed in the future)
+ * - a successful reply always starts with the address and command in the same order the
+ * request used it
+ * - length of the reply data is specific to the command used.
+ * - The replies to most reads are pmbus linear11 encoded
+ * - the PSU expects a "handshake" init command before all other commands will work
+ * - send the handshake by sending 0x51 to the address 0xfa (packet will be [0xfa 0x51])
+ * - the driver supports debugfs for values not fitting into the hwmon class
+ */
+
+#define DRIVER_NAME "msi-psu"
+
+#define REPLY_SIZE 40 /* max length of a reply to a single command */
+#define SAMPLE_INTERVAL_MS 50
+#define CMD_BUFFER_SIZE 64
+#define CMD_TIMEOUT_MS 250
+#define SECONDS_PER_HOUR (60 * 60)
+#define SECONDS_PER_DAY (SECONDS_PER_HOUR * 24)
+
+#define PSU_NAK 0xFE
+#define PSU_REG_VEND_STR 0x10
+#define PSU_REG_PROD_STR 0x11
+#define PSU_REG_REVISION 0x12
+#define PSU_REG_SERIAL 0x13 /* accepted, but returns all zeros */
+
+#define PSU_REG_IN_VOLTS 0x20
+#define PSU_REG_VOUT_12V_EACH_RAIL 0x22
+#define PSU_REG_IOUT_12V_EACH_RAIL 0x23
+#define PSU_REG_VOUT_12V 0x24
+#define PSU_REG_IOUT_12V 0x25
+#define PSU_REG_VOUT_5V 0x26
+#define PSU_REG_IOUT_5V 0x27
+#define PSU_REG_VOUT_3V 0x28
+#define PSU_REG_IOUT_3V 0x29
+#define PSU_REG_TOTAL_WATTS 0x2A
+#define PSU_REG_EFFICIENCY 0x2B
+#define PSU_REG_TEMP0 0x30
+#define PSU_REG_FAN_RPM 0x40
+#define PSU_REG_FAN_MODE 0x41
+#define PSU_REG_FAN_DUTY_CYCLE 0x42
+
+#define PSU_REG_MULTIRAIL 0xC0
+#define PSU_REG_UNKNOWN_C4 0xC4
+#define PSU_REG_UNKNOWN_C6 0xC6
+
+#define PSU_REG_UPTIME 0xD0
+#define PSU_REG_TOTAL_UPTIME 0xD1
+
+#define PSU_REG_READ_EVERYTHING 0xE0
+#define PSU_REG_SAVE_SETTINGS 0xF1
+
+#define PSU_INIT 0xFA
+#define PSU_READ 0x51
+#define PSU_WRITE 0x50
+
+#define PSU_MULTI_RAIL_ENABLED 2
+#define PSU_MULTI_RAIL_DISABLED 1
+
+#define COMBINED_12V 5
+
+#define FAN_MODE_MANUAL 3
+#define FAN_MODE_AUTO 1
+#define FAN_SPEED_MAX 100
+#define FAN_SPEED_MIN 0
+
+struct volt_amp_pair {
+ u16 volts;
+ u16 amps;
+} __packed;
+
+struct msipsu_all {
+ struct volt_amp_pair v12[6];
+ struct volt_amp_pair v5;
+ struct volt_amp_pair v3;
+ u16 watts;
+ u16 eff;
+ u16 temp;
+ u16 fan_speed;
+} __packed;
+
+struct msipsu_data {
+ struct hid_device *hdev;
+ struct device *hwmon_dev;
+ struct dentry *debugfs;
+ struct completion wait_completion;
+ struct mutex lock; /* for locking access to cmd_buffer */
+ u8 *cmd_buffer;
+ char vendor[REPLY_SIZE];
+ char product[REPLY_SIZE];
+ struct debugfs_blob_wrapper vendor_blob;
+ struct debugfs_blob_wrapper product_blob;
+ struct msipsu_all data;
+ ktime_t last_read_all;
+};
+
+/* some values are SMBus LINEAR11 data which need a conversion */
+static int msipsu_lin11_to_int(u16 v16, int scale, bool is_signed)
+{
+ s32 exponent;
+ s32 mantissa;
+ int val;
+
+ exponent = ((s16)v16) >> 11;
+ if (is_signed)
+ mantissa = ((s16)((v16 & 0x7ff) << 5)) >> 5;
+ else
+ mantissa = (u16)(v16 & 0x7ff); /* deliberately not sign-extending here */
+ val = mantissa * scale;
+
+ if (exponent >= 0)
+ val <<= exponent;
+ else
+ val >>= -exponent;
+
+ return val;
+}
+
+static int msipsu_percent_to_pwm(u16 val)
+{
+ return DIV_ROUND_CLOSEST(val * 255, 100);
+}
+
+static int msipsu_pwm_to_percent(long val)
+{
+ if (val < 0 || val > 255)
+ return -EINVAL;
+
+ return DIV_ROUND_CLOSEST(val * 100, 255);
+}
+
+static int msipsu_usb_cmd(struct msipsu_data *priv, const u8 *in, size_t in_len, void *data)
+{
+ unsigned long time;
+ int ret;
+
+ if (in_len > CMD_BUFFER_SIZE)
+ return -ENOBUFS;
+
+ memset(priv->cmd_buffer, 0, CMD_BUFFER_SIZE);
+ memcpy(priv->cmd_buffer, in, in_len);
+
+ reinit_completion(&priv->wait_completion);
+
+ ret = hid_hw_output_report(priv->hdev, priv->cmd_buffer, CMD_BUFFER_SIZE);
+ if (ret < 0)
+ return ret;
+
+ time = wait_for_completion_timeout(&priv->wait_completion,
+ msecs_to_jiffies(CMD_TIMEOUT_MS));
+ if (!time)
+ return -ETIMEDOUT;
+
+ /*
+ * at the start of the reply is an echo of the send command/address in the same order it
+ * was sent. In the event a command/address is not supported, the PSU will reply with a NAK.
+ * For an invalid read, it will look like this:
+ * Out -> [PSU_READ(0x51) A_FAKE_REGISTER(0x69)]
+ * In <- [PSU_READ(0x51) PSU_NAK(0xFE)]
+ * Writes differ slightly, this is the sequence for a write to a non-existent register:
+ * Out -> [PSU_WRITE(0x50) A_FAKE_REGISTER(0x69)]
+ * In <- [PSU_WRITE(0x50) PSU_NAK(0xFE)]
+ * And this is a rejected write (of the correct length) to a real register:
+ * Out -> [PSU_WRITE(0x50) PSU_REG_FAN_MODE(0x41) DATA(0x55 0x55 0x55)]
+ * In <- [PSU_WRITE(0x50) PSU_REG_FAN_MODE(0x41) PSU_NAK(0xFE)]
+ */
+ if (in[0] != priv->cmd_buffer[0] || in[1] != priv->cmd_buffer[1])
+ return -EOPNOTSUPP;
+ else if (in[2] != PSU_NAK && priv->cmd_buffer[2] == PSU_NAK)
+ return -EINVAL;
+
+ if (data)
+ memcpy(data, priv->cmd_buffer + 2, REPLY_SIZE);
+
+ return 0;
+}
+
+static int msipsu_usb_cmd_locked(struct msipsu_data *priv, const u8 *in, size_t in_len, void *data)
+{
+ int ret;
+
+ mutex_lock(&priv->lock);
+ ret = msipsu_usb_cmd(priv, in, in_len, data);
+ mutex_unlock(&priv->lock);
+ return ret;
+}
+
+static int msipsu_fw_init(struct msipsu_data *priv)
+{
+ /*
+ * Vendor SW always begins with a message of [0xfa, 0x51]
+ * This init message is replied to with the model name of the PSU.
+ */
+ const u8 init[] = {PSU_INIT, 0x51};
+ const u8 read_vendor[] = {PSU_READ, PSU_REG_VEND_STR};
+ int ret;
+
+ ret = msipsu_usb_cmd(priv, init, sizeof(init), priv->product);
+ if (ret < 0)
+ return ret;
+ ret = msipsu_usb_cmd(priv, read_vendor, sizeof(read_vendor), priv->vendor);
+ if (ret < 0)
+ return ret;
+ priv->vendor_blob.data = priv->vendor;
+ priv->product_blob.data = priv->product;
+ priv->vendor_blob.size = strnlen(priv->vendor, sizeof(priv->vendor));
+ priv->product_blob.size = strnlen(priv->product, sizeof(priv->product));
+ return ret;
+}
+
+static int msipsu_save_settings(struct msipsu_data *priv)
+{
+ const u8 cmd[] = {PSU_WRITE, PSU_REG_SAVE_SETTINGS, 0x0};
+
+ return msipsu_usb_cmd_locked(priv, cmd, sizeof(cmd), NULL);
+}
+
+static int msipsu_write_fan_settings(struct msipsu_data *priv, u8 mode, long pwm_duty)
+{
+ int ret;
+ int percent_duty = 0;
+
+ if (mode == FAN_MODE_AUTO) {
+ /* vendor SW masks off the duty cycle for auto-mode, we should do the same */
+ percent_duty = FAN_SPEED_MIN;
+ } else if (pwm_duty != 0) {
+ /*
+ * it is an error to write duty to non-zero while the device is not in
+ * manual-fan-mode, so switch mode automatically
+ */
+ mode = FAN_MODE_MANUAL;
+ percent_duty = msipsu_pwm_to_percent(pwm_duty);
+ if (percent_duty < 0) /* return -EINVAL if we got a value we couldn't convert */
+ return percent_duty;
+ }
+ const u8 cmd[] = {PSU_WRITE, PSU_REG_FAN_MODE, mode, 0, percent_duty};
+
+ ret = msipsu_usb_cmd_locked(priv, cmd, sizeof(cmd), NULL);
+ if (ret < 0)
+ return ret;
+ return msipsu_save_settings(priv);
+}
+
+static int msipsu_get_all_values(struct msipsu_data *priv)
+{
+ const u8 read_cmd[] = {PSU_READ, PSU_REG_READ_EVERYTHING};
+ ktime_t t = ktime_get();
+ s64 delta = ktime_ms_delta(t, priv->last_read_all);
+
+ if (delta < SAMPLE_INTERVAL_MS)
+ return 0;
+
+ priv->last_read_all = t;
+ return msipsu_usb_cmd_locked(priv, read_cmd, sizeof(read_cmd), &priv->data);
+}
+
+static int msipsu_get_value(struct msipsu_data *priv, u8 cmd, long *val)
+{
+ u8 data[REPLY_SIZE];
+ const u8 read_cmd[] = {PSU_READ, cmd};
+ int ret = msipsu_usb_cmd_locked(priv, read_cmd, sizeof(read_cmd), data);
+
+ if (ret < 0)
+ return ret;
+
+ u16 tmp16 = (data[1] << 8) + data[0];
+
+ switch (cmd) {
+ case PSU_REG_IN_VOLTS:
+ case PSU_REG_VOUT_12V:
+ case PSU_REG_IOUT_12V:
+ case PSU_REG_VOUT_5V:
+ case PSU_REG_IOUT_5V:
+ case PSU_REG_VOUT_3V:
+ case PSU_REG_IOUT_3V:
+ case PSU_REG_TEMP0:
+ *val = msipsu_lin11_to_int(tmp16, 1000, true);
+ break;
+ case PSU_REG_EFFICIENCY:
+ *val = msipsu_lin11_to_int(tmp16, 100, true);
+ break;
+ case PSU_REG_FAN_RPM:
+ *val = msipsu_lin11_to_int(tmp16, 1, false);
+ break;
+ case PSU_REG_TOTAL_WATTS:
+ *val = msipsu_lin11_to_int(tmp16, 1000000, true);
+ break;
+ case PSU_REG_FAN_MODE:
+ case PSU_REG_FAN_DUTY_CYCLE:
+ case PSU_REG_TOTAL_UPTIME:
+ case PSU_REG_UPTIME:
+ case PSU_REG_REVISION:
+ *val = ((long)data[3] << 24) + (data[2] << 16) + tmp16;
+ break;
+ case PSU_REG_MULTIRAIL:
+ switch (data[0]) {
+ case PSU_MULTI_RAIL_DISABLED:
+ *val = 0;
+ break;
+ case PSU_MULTI_RAIL_ENABLED:
+ *val = 1;
+ break;
+ default:
+ *val = 0xff;
+ break;
+ }
+ break;
+ default:
+ ret = -EOPNOTSUPP;
+ break;
+ }
+
+ return ret;
+}
+
+static umode_t msipsu_hwmon_ops_is_visible(const void *data, enum hwmon_sensor_types type,
+ u32 attr, int channel)
+{
+ if (type == hwmon_temp && (attr == hwmon_temp_input || attr == hwmon_temp_label))
+ return 0444;
+ else if (type == hwmon_fan && (attr == hwmon_fan_input || attr == hwmon_fan_label))
+ return 0444;
+ else if (type == hwmon_pwm && (attr == hwmon_pwm_enable || attr == hwmon_pwm_input))
+ return 0644;
+ else if (type == hwmon_power && (attr == hwmon_power_input || attr == hwmon_power_label))
+ return 0444;
+ else if (type == hwmon_in && (attr == hwmon_in_input || attr == hwmon_in_label))
+ return 0444;
+ else if (type == hwmon_curr && (attr == hwmon_curr_input || attr == hwmon_curr_label))
+ return 0444;
+
+ return 0;
+}
+
+static int msipsu_hwmon_ops_read(struct device *dev, enum hwmon_sensor_types type, u32 attr,
+ int channel, long *val)
+{
+ struct msipsu_data *priv = dev_get_drvdata(dev);
+ int ret;
+
+ if (type != hwmon_pwm) {
+ /* PWM controls don't use the "all" packet, so don't read it */
+ ret = msipsu_get_all_values(priv);
+ if (ret < 0)
+ return ret;
+ }
+
+ if (type == hwmon_temp && attr == hwmon_temp_input) {
+ *val = msipsu_lin11_to_int(priv->data.temp, 1000, true);
+ } else if (type == hwmon_fan && attr == hwmon_fan_input) {
+ *val = msipsu_lin11_to_int(priv->data.fan_speed, 1, false);
+ } else if (type == hwmon_pwm) {
+ switch (attr) {
+ case hwmon_pwm_enable:
+ ret = msipsu_get_value(priv, PSU_REG_FAN_MODE, val);
+ *val &= 0xff;
+ break;
+ case hwmon_pwm_input:
+ ret = msipsu_get_value(priv, PSU_REG_FAN_DUTY_CYCLE, val);
+ *val &= 0xff; /* there's a "calculated" DC in the next byte up */
+ *val = msipsu_percent_to_pwm(*val);
+ break;
+ default:
+ ret = -EOPNOTSUPP;
+ break;
+ }
+ } else if (type == hwmon_power && attr == hwmon_power_input) {
+ *val = msipsu_lin11_to_int(priv->data.watts, 1000000, true);
+ } else if (type == hwmon_in && attr == hwmon_in_input) {
+ switch (channel) {
+ case 0:
+ ret = msipsu_get_value(priv, PSU_REG_IN_VOLTS, val);
+ break;
+ case 1:
+ *val = msipsu_lin11_to_int(priv->data.v12[COMBINED_12V].volts, 1000, true);
+ break;
+ case 2:
+ *val = msipsu_lin11_to_int(priv->data.v5.volts, 1000, true);
+ break;
+ case 3:
+ *val = msipsu_lin11_to_int(priv->data.v3.volts, 1000, true);
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+ } else if (type == hwmon_curr && attr == hwmon_curr_input) {
+ switch (channel) {
+ case 0:
+ *val = msipsu_lin11_to_int(priv->data.v12[COMBINED_12V].amps, 1000, true);
+ break;
+ case 1:
+ *val = msipsu_lin11_to_int(priv->data.v5.amps, 1000, true);
+ break;
+ case 2:
+ *val = msipsu_lin11_to_int(priv->data.v3.amps, 1000, true);
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+ } else {
+ return -EOPNOTSUPP;
+ }
+
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+static int msipsu_hwmon_ops_read_string(struct device *dev, enum hwmon_sensor_types type, u32 attr,
+ int channel, const char **str)
+{
+ static const char *const label_volts[] = {
+ "v_in",
+ "v_out +12v",
+ "v_out +5v",
+ "v_out +3.3v"
+ };
+
+ static const char *const label_amps[] = {
+ "curr +12v",
+ "curr +5v",
+ "curr +3.3v"
+ };
+
+ if (type == hwmon_temp && attr == hwmon_temp_label) {
+ *str = "psu temp";
+ return 0;
+ } else if (type == hwmon_fan && attr == hwmon_fan_label) {
+ *str = "psu fan";
+ return 0;
+ } else if (type == hwmon_power && attr == hwmon_power_label) {
+ *str = "power total";
+ return 0;
+ } else if (type == hwmon_in && attr == hwmon_in_label && channel < 4) {
+ *str = label_volts[channel];
+ return 0;
+ } else if (type == hwmon_curr && attr == hwmon_curr_label && channel < 3) {
+ *str = label_amps[channel];
+ return 0;
+ }
+
+ return -EOPNOTSUPP;
+}
+
+static int msipsu_hwmon_ops_write(struct device *dev, enum hwmon_sensor_types type, u32 attr,
+ int channel, long val)
+{
+ struct msipsu_data *priv = dev_get_drvdata(dev);
+
+ if (type != hwmon_pwm)
+ return -EOPNOTSUPP;
+
+ switch (attr) {
+ case hwmon_pwm_enable:
+ switch (val) {
+ case FAN_MODE_AUTO:
+ return msipsu_write_fan_settings(priv, val, FAN_SPEED_MIN);
+ case FAN_MODE_MANUAL:
+ return msipsu_write_fan_settings(priv, val, FAN_SPEED_MAX);
+ default:
+ return -EINVAL;
+ }
+ case hwmon_pwm_input:
+ return msipsu_write_fan_settings(priv, FAN_MODE_MANUAL, val);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static const struct hwmon_ops msipsu_hwmon_ops = {
+ .is_visible = msipsu_hwmon_ops_is_visible,
+ .read = msipsu_hwmon_ops_read,
+ .write = msipsu_hwmon_ops_write,
+ .read_string = msipsu_hwmon_ops_read_string,
+};
+
+static const struct hwmon_channel_info *msipsu_info[] = {
+ HWMON_CHANNEL_INFO(chip,
+ HWMON_C_REGISTER_TZ),
+ HWMON_CHANNEL_INFO(temp,
+ HWMON_T_INPUT | HWMON_T_LABEL),
+ HWMON_CHANNEL_INFO(fan,
+ HWMON_F_INPUT | HWMON_F_LABEL),
+ HWMON_CHANNEL_INFO(pwm,
+ HWMON_PWM_INPUT | HWMON_PWM_ENABLE),
+ HWMON_CHANNEL_INFO(power,
+ HWMON_P_INPUT | HWMON_P_LABEL),
+ HWMON_CHANNEL_INFO(in,
+ HWMON_I_INPUT | HWMON_I_LABEL,
+ HWMON_I_INPUT | HWMON_I_LABEL,
+ HWMON_I_INPUT | HWMON_I_LABEL,
+ HWMON_I_INPUT | HWMON_I_LABEL),
+ HWMON_CHANNEL_INFO(curr,
+ HWMON_C_INPUT | HWMON_C_LABEL,
+ HWMON_C_INPUT | HWMON_C_LABEL,
+ HWMON_C_INPUT | HWMON_C_LABEL),
+ NULL
+};
+
+static const struct hwmon_chip_info msipsu_chip_info = {
+ .ops = &msipsu_hwmon_ops,
+ .info = msipsu_info,
+};
+
+#ifdef CONFIG_DEBUG_FS
+
+static void print_uptime(struct seq_file *seqf, u8 cmd)
+{
+ struct msipsu_data *priv = seqf->private;
+ long val = 0;
+ int ret = msipsu_get_value(priv, cmd, &val);
+
+ if (ret < 0) {
+ seq_puts(seqf, "N/A\n");
+ return;
+ }
+
+ if (val > SECONDS_PER_DAY) {
+ seq_printf(seqf, "%ld day(s), %02ld:%02ld:%02ld\n", val / SECONDS_PER_DAY,
+ val % SECONDS_PER_DAY / SECONDS_PER_HOUR, val % SECONDS_PER_HOUR / 60,
+ val % 60);
+ return;
+ }
+
+ seq_printf(seqf, "%02ld:%02ld:%02ld\n", val % SECONDS_PER_DAY / SECONDS_PER_HOUR,
+ val % SECONDS_PER_HOUR / 60, val % 60);
+}
+
+static int uptime_show(struct seq_file *seqf, void *unused)
+{
+ print_uptime(seqf, PSU_REG_UPTIME);
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(uptime);
+
+static int uptime_total_show(struct seq_file *seqf, void *unused)
+{
+ print_uptime(seqf, PSU_REG_TOTAL_UPTIME);
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(uptime_total);
+
+static int revision_show(struct seq_file *seqf, void *unused)
+{
+ struct msipsu_data *priv = seqf->private;
+ long val = 0;
+ int ret = msipsu_get_value(priv, PSU_REG_REVISION, &val);
+
+ if (ret < 0) {
+ seq_puts(seqf, "N/A\n");
+ return 0;
+ }
+
+ seq_printf(seqf, "%c.%c\n", (char)(val & 0xff), (char)((val >> 8) & 0xff));
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(revision);
+
+static int efficiency_show(struct seq_file *seqf, void *unused)
+{
+ struct msipsu_data *priv = seqf->private;
+ int ret = msipsu_get_all_values(priv);
+
+ if (ret < 0) {
+ seq_puts(seqf, "N/A\n");
+ return 0;
+ }
+
+ seq_printf(seqf, "%d\n", msipsu_lin11_to_int(priv->data.eff, 100, true));
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(efficiency);
+
+static int multi_rail_read(void *data, u64 *val)
+{
+ return msipsu_get_value((struct msipsu_data *)data, PSU_REG_MULTIRAIL, (long *)val);
+}
+
+static int msipsu_write_rail_setting(struct msipsu_data *priv, bool multi_enabled)
+{
+ long currently_enabled;
+ int ret = msipsu_get_value(priv, PSU_REG_MULTIRAIL, ¤tly_enabled);
+
+ if (ret < 0)
+ return ret;
+
+ /* hardware returns an error if we try to set the mode to the current mode. Avoid this. */
+ if (currently_enabled == multi_enabled)
+ return 0;
+
+ u8 to_write = multi_enabled ? PSU_MULTI_RAIL_ENABLED : PSU_MULTI_RAIL_DISABLED;
+ const u8 cmd[] = {PSU_WRITE, PSU_REG_MULTIRAIL, to_write};
+
+ ret = msipsu_usb_cmd_locked(priv, cmd, sizeof(cmd), NULL);
+ if (ret < 0)
+ return ret;
+ return msipsu_save_settings(priv);
+}
+
+static int multi_rail_write(void *data, u64 val)
+{
+ struct msipsu_data *priv = data;
+
+ switch (val) {
+ case 0:
+ return msipsu_write_rail_setting(priv, false);
+ case 1:
+ return msipsu_write_rail_setting(priv, true);
+ default:
+ return -EINVAL;
+ }
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(multi_rail_fops, multi_rail_read, multi_rail_write, "%llu\n");
+
+static void msipsu_debugfs_init(struct msipsu_data *priv)
+{
+ char name[32];
+
+ scnprintf(name, sizeof(name), "%s-%s", DRIVER_NAME, dev_name(&priv->hdev->dev));
+
+ priv->debugfs = debugfs_create_dir(name, NULL);
+ debugfs_create_file("uptime", 0444, priv->debugfs, priv, &uptime_fops);
+ debugfs_create_file("uptime_total", 0444, priv->debugfs, priv, &uptime_total_fops);
+ debugfs_create_blob("vendor", 0444, priv->debugfs, &priv->vendor_blob);
+ debugfs_create_blob("product", 0444, priv->debugfs, &priv->product_blob);
+ debugfs_create_file("revision", 0444, priv->debugfs, priv, &revision_fops);
+ debugfs_create_file("efficiency", 0444, priv->debugfs, priv, &efficiency_fops);
+ debugfs_create_file("multi_rail_enabled", 0644, priv->debugfs, priv, &multi_rail_fops);
+}
+
+#else
+
+static void msipsu_debugfs_init(struct msipsu_data *priv)
+{
+}
+
+#endif
+
+static int msipsu_probe(struct hid_device *hdev, const struct hid_device_id *id)
+{
+ struct msipsu_data *priv;
+ int ret;
+
+ priv = devm_kzalloc(&hdev->dev, sizeof(struct msipsu_data), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->cmd_buffer = devm_kmalloc(&hdev->dev, CMD_BUFFER_SIZE, GFP_KERNEL);
+ if (!priv->cmd_buffer)
+ return -ENOMEM;
+
+ ret = hid_parse(hdev);
+ if (ret)
+ return ret;
+
+ ret = hid_hw_start(hdev, HID_CONNECT_HIDRAW);
+ if (ret)
+ return ret;
+
+ ret = hid_hw_open(hdev);
+ if (ret)
+ goto fail_and_stop;
+
+ priv->hdev = hdev;
+ hid_set_drvdata(hdev, priv);
+ mutex_init(&priv->lock);
+ init_completion(&priv->wait_completion);
+
+ hid_device_io_start(hdev);
+
+ ret = msipsu_fw_init(priv);
+ if (ret < 0) {
+ dev_err(&hdev->dev, "unable to initialize device (%d)\n", ret);
+ goto fail_and_close;
+ }
+
+ priv->hwmon_dev = hwmon_device_register_with_info(&hdev->dev, "msipsu", priv,
+ &msipsu_chip_info, NULL);
+
+ if (IS_ERR(priv->hwmon_dev)) {
+ ret = PTR_ERR(priv->hwmon_dev);
+ goto fail_and_close;
+ }
+
+ msipsu_debugfs_init(priv);
+
+ return 0;
+
+fail_and_close:
+ hid_hw_close(hdev);
+fail_and_stop:
+ hid_hw_stop(hdev);
+ return ret;
+}
+
+static void msipsu_remove(struct hid_device *hdev)
+{
+ struct msipsu_data *priv = hid_get_drvdata(hdev);
+
+ debugfs_remove_recursive(priv->debugfs);
+ hwmon_device_unregister(priv->hwmon_dev);
+ hid_hw_close(hdev);
+ hid_hw_stop(hdev);
+}
+
+static int msipsu_raw_event(struct hid_device *hdev, struct hid_report *report, u8 *data, int size)
+{
+ struct msipsu_data *priv = hid_get_drvdata(hdev);
+
+ if (completion_done(&priv->wait_completion))
+ return 0;
+
+ memcpy(priv->cmd_buffer, data, min(CMD_BUFFER_SIZE, size));
+ complete(&priv->wait_completion);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int msipsu_resume(struct hid_device *hdev)
+{
+ struct msipsu_data *priv = hid_get_drvdata(hdev);
+
+ /* some PSUs turn off the microcontroller during standby, so a reinit is required */
+ return msipsu_fw_init(priv);
+}
+#endif
+
+static const struct hid_device_id msipsu_idtable[] = {
+ { HID_USB_DEVICE(0xdb0, 0x56d4) }, /* MEG Ai1300P */
+ { HID_USB_DEVICE(0xdb0, 0xe749) }, /* MEG Ai1000P */
+ { },
+};
+MODULE_DEVICE_TABLE(hid, msipsu_idtable);
+
+static struct hid_driver msipsu_driver = {
+ .name = DRIVER_NAME,
+ .id_table = msipsu_idtable,
+ .probe = msipsu_probe,
+ .remove = msipsu_remove,
+ .raw_event = msipsu_raw_event,
+#ifdef CONFIG_PM
+ .resume = msipsu_resume,
+ .reset_resume = msipsu_resume,
+#endif
+};
+
+static int __init msipsu_init(void)
+{
+ return hid_register_driver(&msipsu_driver);
+}
+
+static void __exit msipsu_exit(void)
+{
+ hid_unregister_driver(&msipsu_driver);
+}
+
+/*
+ * With module_init() the driver would load before the HID bus when
+ * built-in, so use late_initcall() instead.
+ */
+late_initcall(msipsu_init);
+module_exit(msipsu_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Jack Doan <me@jackdoan.com>");
+MODULE_DESCRIPTION("Driver for MSI power supplies with HID sensor interface");
This driver provides a sysfs interface for MSI power supplies with a USB-HID monitoring interface. Measurements for the output voltage and current for each rail are provided, as well as total output power, temperature, and fan control. This patch adds: - hwmon driver msi-psu - hwmon documentation - updates MAINTAINERS Signed-off-by: Jack Doan <me@jackdoan.com> --- Documentation/hwmon/index.rst | 1 + Documentation/hwmon/msi-psu.rst | 64 +++ MAINTAINERS | 7 + drivers/hwmon/Kconfig | 12 + drivers/hwmon/Makefile | 1 + drivers/hwmon/msi-psu.c | 801 ++++++++++++++++++++++++++++++++ 6 files changed, 886 insertions(+) create mode 100644 Documentation/hwmon/msi-psu.rst create mode 100644 drivers/hwmon/msi-psu.c