diff mbox series

[v9,07/12] clk: meson: add vclk driver

Message ID 20231124-amlogic-v6-4-upstream-dsi-ccf-vim3-v9-7-95256ed139e6@linaro.org
State Handled Elsewhere
Headers show
Series drm/meson: add support for MIPI DSI Display | expand

Commit Message

Neil Armstrong Nov. 24, 2023, 8:41 a.m. UTC
The VCLK and VCLK_DIV clocks have supplementary bits.

The VCLK has a "SOFT RESET" bit to toggle after the whole
VCLK sub-tree rate has been set, this is implemented in
the gate enable callback.

The VCLK_DIV clocks as enable and reset bits used to disable
and reset the divider, associated with CLK_SET_RATE_GATE it ensures
the rate is set while the divider is disabled and in reset mode.

The VCLK_DIV enable bit isn't implemented as a gate since it's part
of the divider logic and vendor does this exact sequence to ensure
the divider is correctly set.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 drivers/clk/meson/Kconfig  |   5 ++
 drivers/clk/meson/Makefile |   1 +
 drivers/clk/meson/vclk.c   | 141 +++++++++++++++++++++++++++++++++++++++++++++
 drivers/clk/meson/vclk.h   |  51 ++++++++++++++++
 4 files changed, 198 insertions(+)

Comments

Jerome Brunet Nov. 24, 2023, 2:41 p.m. UTC | #1
On Fri 24 Nov 2023 at 09:41, Neil Armstrong <neil.armstrong@linaro.org> wrote:

> The VCLK and VCLK_DIV clocks have supplementary bits.
>
> The VCLK has a "SOFT RESET" bit to toggle after the whole
> VCLK sub-tree rate has been set, this is implemented in
> the gate enable callback.
>
> The VCLK_DIV clocks as enable and reset bits used to disable
> and reset the divider, associated with CLK_SET_RATE_GATE it ensures
> the rate is set while the divider is disabled and in reset mode.
>
> The VCLK_DIV enable bit isn't implemented as a gate since it's part
> of the divider logic and vendor does this exact sequence to ensure
> the divider is correctly set.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
>  drivers/clk/meson/Kconfig  |   5 ++
>  drivers/clk/meson/Makefile |   1 +
>  drivers/clk/meson/vclk.c   | 141 +++++++++++++++++++++++++++++++++++++++++++++
>  drivers/clk/meson/vclk.h   |  51 ++++++++++++++++
>  4 files changed, 198 insertions(+)
>
> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
> index 29ffd14d267b..59a40a49f8e1 100644
> --- a/drivers/clk/meson/Kconfig
> +++ b/drivers/clk/meson/Kconfig
> @@ -30,6 +30,10 @@ config COMMON_CLK_MESON_VID_PLL_DIV
>  	tristate
>  	select COMMON_CLK_MESON_REGMAP
>  
> +config COMMON_CLK_MESON_VCLK
> +	tristate
> +	select COMMON_CLK_MESON_REGMAP
> +
>  config COMMON_CLK_MESON_CLKC_UTILS
>  	tristate
>  
> @@ -140,6 +144,7 @@ config COMMON_CLK_G12A
>  	select COMMON_CLK_MESON_EE_CLKC
>  	select COMMON_CLK_MESON_CPU_DYNDIV
>  	select COMMON_CLK_MESON_VID_PLL_DIV
> +	select COMMON_CLK_MESON_VCLK

This particular line belong in the next patch

>  	select MFD_SYSCON
>  	help
>  	  Support for the clock controller on Amlogic S905D2, S905X2 and S905Y2
> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
> index 9ee4b954c896..9ba43fe7a07a 100644
> --- a/drivers/clk/meson/Makefile
> +++ b/drivers/clk/meson/Makefile
> @@ -12,6 +12,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_PLL) += clk-pll.o
>  obj-$(CONFIG_COMMON_CLK_MESON_REGMAP) += clk-regmap.o
>  obj-$(CONFIG_COMMON_CLK_MESON_SCLK_DIV) += sclk-div.o
>  obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
> +obj-$(CONFIG_COMMON_CLK_MESON_VCLK) += vclk.o
>  
>  # Amlogic Clock controllers
>  
> diff --git a/drivers/clk/meson/vclk.c b/drivers/clk/meson/vclk.c
> new file mode 100644
> index 000000000000..47f08a52b49f
> --- /dev/null
> +++ b/drivers/clk/meson/vclk.c
> @@ -0,0 +1,141 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
> + */
> +
> +#include <linux/module.h>
> +#include "vclk.h"
> +
> +/* The VCLK gate has a supplementary reset bit to pulse after ungating */
> +
> +static inline struct clk_regmap_vclk_data *
> +clk_get_regmap_vclk_data(struct clk_regmap *clk)
> +{
> +	return (struct clk_regmap_vclk_data *)clk->data;
> +}
> +
> +static int clk_regmap_vclk_enable(struct clk_hw *hw)
> +{
> +	struct clk_regmap *clk = to_clk_regmap(hw);
> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
> +
> +	meson_parm_write(clk->map, &vclk->enable, 1);
> +
> +	/* Do a reset pulse */
> +	meson_parm_write(clk->map, &vclk->reset, 1);
> +	meson_parm_write(clk->map, &vclk->reset, 0);
> +
> +	return 0;
> +}
> +
> +static void clk_regmap_vclk_disable(struct clk_hw *hw)
> +{
> +	struct clk_regmap *clk = to_clk_regmap(hw);
> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
> +
> +	meson_parm_write(clk->map, &vclk->enable, 0);
> +}
> +
> +static int clk_regmap_vclk_is_enabled(struct clk_hw *hw)
> +{
> +	struct clk_regmap *clk = to_clk_regmap(hw);
> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
> +
> +	return meson_parm_read(clk->map, &vclk->enable);
> +}
> +
> +const struct clk_ops clk_regmap_vclk_ops = {
> +	.enable = clk_regmap_vclk_enable,
> +	.disable = clk_regmap_vclk_disable,
> +	.is_enabled = clk_regmap_vclk_is_enabled,
> +};
> +EXPORT_SYMBOL_GPL(clk_regmap_vclk_ops);

s/clk_regmap_vclk/meson_vclk at least for what is exported, ideally most
all the code.

I get clk_regmap_ comes from code copied from clk_regmap.c.
The reason the this part is different (and not using parm) if that when
I converted amlogic to regmap, I hope we could make this generic,
possibly converging between aml and qcom (which was the only other
platform using regmap for clock at the time). This is why clk_regmap.c
is a bit different from the other driver.

For the aml specific drivers, best to look at the mpll or cpu-dyndiv one.

> +
> +/* The VCLK Divider has supplementary reset & enable bits */
> +
> +static inline struct clk_regmap_vclk_div_data *
> +clk_get_regmap_vclk_div_data(struct clk_regmap *clk)
> +{
> +	return (struct clk_regmap_vclk_div_data *)clk->data;
> +}
> +
> +static unsigned long clk_regmap_vclk_div_recalc_rate(struct clk_hw *hw,
> +						     unsigned long prate)
> +{
> +	struct clk_regmap *clk = to_clk_regmap(hw);
> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
> +
> +	return divider_recalc_rate(hw, prate, meson_parm_read(clk->map, &vclk->div),
> +				   vclk->table, vclk->flags, vclk->div.width);
> +}
> +
> +static int clk_regmap_vclk_div_determine_rate(struct clk_hw *hw,
> +					      struct clk_rate_request *req)
> +{
> +	struct clk_regmap *clk = to_clk_regmap(hw);
> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
> +
> +	return divider_determine_rate(hw, req, vclk->table, vclk->div.width,
> +				      vclk->flags);
> +}
> +
> +static int clk_regmap_vclk_div_set_rate(struct clk_hw *hw, unsigned long rate,
> +					unsigned long parent_rate)
> +{
> +	struct clk_regmap *clk = to_clk_regmap(hw);
> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
> +	int ret;
> +
> +	ret = divider_get_val(rate, parent_rate, vclk->table, vclk->div.width,
> +			      vclk->flags);
> +	if (ret < 0)
> +		return ret;
> +
> +	meson_parm_write(clk->map, &vclk->div, ret);
> +
> +	return 0;
> +};
> +
> +static int clk_regmap_vclk_div_enable(struct clk_hw *hw)
> +{
> +	struct clk_regmap *clk = to_clk_regmap(hw);
> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
> +
> +	/* Unreset the divider when ungating */
> +	meson_parm_write(clk->map, &vclk->reset, 0);
> +	meson_parm_write(clk->map, &vclk->enable, 1);
> +
> +	return 0;
> +}
> +
> +static void clk_regmap_vclk_div_disable(struct clk_hw *hw)
> +{
> +	struct clk_regmap *clk = to_clk_regmap(hw);
> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
> +
> +	/* Reset the divider when gating */
> +	meson_parm_write(clk->map, &vclk->enable, 0);
> +	meson_parm_write(clk->map, &vclk->reset, 1);
> +}
> +
> +static int clk_regmap_vclk_div_is_enabled(struct clk_hw *hw)
> +{
> +	struct clk_regmap *clk = to_clk_regmap(hw);
> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
> +
> +	return meson_parm_read(clk->map, &vclk->enable);
> +}
> +
> +const struct clk_ops clk_regmap_vclk_div_ops = {
> +	.recalc_rate = clk_regmap_vclk_div_recalc_rate,
> +	.determine_rate = clk_regmap_vclk_div_determine_rate,
> +	.set_rate = clk_regmap_vclk_div_set_rate,
> +	.enable = clk_regmap_vclk_div_enable,
> +	.disable = clk_regmap_vclk_div_disable,
> +	.is_enabled = clk_regmap_vclk_div_is_enabled,
> +};
> +EXPORT_SYMBOL_GPL(clk_regmap_vclk_div_ops);
> +
> +MODULE_DESCRIPTION("Amlogic vclk clock driver");
> +MODULE_AUTHOR("Neil Armstrong <neil.armstrong@linaro.org>");
> +MODULE_LICENSE("GPL v2");
> diff --git a/drivers/clk/meson/vclk.h b/drivers/clk/meson/vclk.h
> new file mode 100644
> index 000000000000..4f25d7ad2717
> --- /dev/null
> +++ b/drivers/clk/meson/vclk.h
> @@ -0,0 +1,51 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
> + */
> +
> +#ifndef __VCLK_H
> +#define __VCLK_H

This is too generic.
Please add the MESON prefix like the other clock driver please.

> +
> +#include "clk-regmap.h"
> +#include "parm.h"
> +
> +/**
> + * struct clk_regmap_vclk_data - vclk regmap backed specific data
> + *
> + * @enable:	vclk enable field
> + * @reset:	vclk reset field
> + * @flags:	hardware-specific flags
> + *
> + * Flags:
> + * Same as clk_gate except CLK_GATE_HIWORD_MASK which is ignored
> + */
> +struct clk_regmap_vclk_data {
> +	struct parm enable;
> +	struct parm reset;
> +	u8 flags;
> +};
> +
> +extern const struct clk_ops clk_regmap_vclk_ops;
> +
> +/**
> + * struct clk_regmap_vclk_div_data - vclk_div regmap back specific data
> + *
> + * @div:	divider field
> + * @enable:	vclk divider enable field
> + * @reset:	vclk divider reset field
> + * @table:	array of value/divider pairs, last entry should have div = 0
> + *
> + * Flags:
> + * Same as clk_divider except CLK_DIVIDER_HIWORD_MASK which is ignored
> + */
> +struct clk_regmap_vclk_div_data {
> +	struct parm div;
> +	struct parm enable;
> +	struct parm reset;
> +	const struct clk_div_table *table;
> +	u8 flags;
> +};
> +
> +extern const struct clk_ops clk_regmap_vclk_div_ops;
> +
> +#endif /* __VCLK_H */
Neil Armstrong Nov. 27, 2023, 8:22 a.m. UTC | #2
On 24/11/2023 15:41, Jerome Brunet wrote:
> 
> On Fri 24 Nov 2023 at 09:41, Neil Armstrong <neil.armstrong@linaro.org> wrote:
> 
>> The VCLK and VCLK_DIV clocks have supplementary bits.
>>
>> The VCLK has a "SOFT RESET" bit to toggle after the whole
>> VCLK sub-tree rate has been set, this is implemented in
>> the gate enable callback.
>>
>> The VCLK_DIV clocks as enable and reset bits used to disable
>> and reset the divider, associated with CLK_SET_RATE_GATE it ensures
>> the rate is set while the divider is disabled and in reset mode.
>>
>> The VCLK_DIV enable bit isn't implemented as a gate since it's part
>> of the divider logic and vendor does this exact sequence to ensure
>> the divider is correctly set.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>> ---
>>   drivers/clk/meson/Kconfig  |   5 ++
>>   drivers/clk/meson/Makefile |   1 +
>>   drivers/clk/meson/vclk.c   | 141 +++++++++++++++++++++++++++++++++++++++++++++
>>   drivers/clk/meson/vclk.h   |  51 ++++++++++++++++
>>   4 files changed, 198 insertions(+)
>>
>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>> index 29ffd14d267b..59a40a49f8e1 100644
>> --- a/drivers/clk/meson/Kconfig
>> +++ b/drivers/clk/meson/Kconfig
>> @@ -30,6 +30,10 @@ config COMMON_CLK_MESON_VID_PLL_DIV
>>   	tristate
>>   	select COMMON_CLK_MESON_REGMAP
>>   
>> +config COMMON_CLK_MESON_VCLK
>> +	tristate
>> +	select COMMON_CLK_MESON_REGMAP
>> +
>>   config COMMON_CLK_MESON_CLKC_UTILS
>>   	tristate
>>   
>> @@ -140,6 +144,7 @@ config COMMON_CLK_G12A
>>   	select COMMON_CLK_MESON_EE_CLKC
>>   	select COMMON_CLK_MESON_CPU_DYNDIV
>>   	select COMMON_CLK_MESON_VID_PLL_DIV
>> +	select COMMON_CLK_MESON_VCLK
> 
> This particular line belong in the next patch

Indeed

> 
>>   	select MFD_SYSCON
>>   	help
>>   	  Support for the clock controller on Amlogic S905D2, S905X2 and S905Y2
>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>> index 9ee4b954c896..9ba43fe7a07a 100644
>> --- a/drivers/clk/meson/Makefile
>> +++ b/drivers/clk/meson/Makefile
>> @@ -12,6 +12,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_PLL) += clk-pll.o
>>   obj-$(CONFIG_COMMON_CLK_MESON_REGMAP) += clk-regmap.o
>>   obj-$(CONFIG_COMMON_CLK_MESON_SCLK_DIV) += sclk-div.o
>>   obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
>> +obj-$(CONFIG_COMMON_CLK_MESON_VCLK) += vclk.o
>>   
>>   # Amlogic Clock controllers
>>   
>> diff --git a/drivers/clk/meson/vclk.c b/drivers/clk/meson/vclk.c
>> new file mode 100644
>> index 000000000000..47f08a52b49f
>> --- /dev/null
>> +++ b/drivers/clk/meson/vclk.c
>> @@ -0,0 +1,141 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
>> + */
>> +
>> +#include <linux/module.h>
>> +#include "vclk.h"
>> +
>> +/* The VCLK gate has a supplementary reset bit to pulse after ungating */
>> +
>> +static inline struct clk_regmap_vclk_data *
>> +clk_get_regmap_vclk_data(struct clk_regmap *clk)
>> +{
>> +	return (struct clk_regmap_vclk_data *)clk->data;
>> +}
>> +
>> +static int clk_regmap_vclk_enable(struct clk_hw *hw)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>> +
>> +	meson_parm_write(clk->map, &vclk->enable, 1);
>> +
>> +	/* Do a reset pulse */
>> +	meson_parm_write(clk->map, &vclk->reset, 1);
>> +	meson_parm_write(clk->map, &vclk->reset, 0);
>> +
>> +	return 0;
>> +}
>> +
>> +static void clk_regmap_vclk_disable(struct clk_hw *hw)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>> +
>> +	meson_parm_write(clk->map, &vclk->enable, 0);
>> +}
>> +
>> +static int clk_regmap_vclk_is_enabled(struct clk_hw *hw)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>> +
>> +	return meson_parm_read(clk->map, &vclk->enable);
>> +}
>> +
>> +const struct clk_ops clk_regmap_vclk_ops = {
>> +	.enable = clk_regmap_vclk_enable,
>> +	.disable = clk_regmap_vclk_disable,
>> +	.is_enabled = clk_regmap_vclk_is_enabled,
>> +};
>> +EXPORT_SYMBOL_GPL(clk_regmap_vclk_ops);
> 
> s/clk_regmap_vclk/meson_vclk at least for what is exported, ideally most
> all the code.
> 
> I get clk_regmap_ comes from code copied from clk_regmap.c.
> The reason the this part is different (and not using parm) if that when
> I converted amlogic to regmap, I hope we could make this generic,
> possibly converging between aml and qcom (which was the only other
> platform using regmap for clock at the time). This is why clk_regmap.c
> is a bit different from the other driver.
> 
> For the aml specific drivers, best to look at the mpll or cpu-dyndiv one.

Ack

> 
>> +
>> +/* The VCLK Divider has supplementary reset & enable bits */
>> +
>> +static inline struct clk_regmap_vclk_div_data *
>> +clk_get_regmap_vclk_div_data(struct clk_regmap *clk)
>> +{
>> +	return (struct clk_regmap_vclk_div_data *)clk->data;
>> +}
>> +
>> +static unsigned long clk_regmap_vclk_div_recalc_rate(struct clk_hw *hw,
>> +						     unsigned long prate)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>> +
>> +	return divider_recalc_rate(hw, prate, meson_parm_read(clk->map, &vclk->div),
>> +				   vclk->table, vclk->flags, vclk->div.width);
>> +}
>> +
>> +static int clk_regmap_vclk_div_determine_rate(struct clk_hw *hw,
>> +					      struct clk_rate_request *req)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>> +
>> +	return divider_determine_rate(hw, req, vclk->table, vclk->div.width,
>> +				      vclk->flags);
>> +}
>> +
>> +static int clk_regmap_vclk_div_set_rate(struct clk_hw *hw, unsigned long rate,
>> +					unsigned long parent_rate)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>> +	int ret;
>> +
>> +	ret = divider_get_val(rate, parent_rate, vclk->table, vclk->div.width,
>> +			      vclk->flags);
>> +	if (ret < 0)
>> +		return ret;
>> +
>> +	meson_parm_write(clk->map, &vclk->div, ret);
>> +
>> +	return 0;
>> +};
>> +
>> +static int clk_regmap_vclk_div_enable(struct clk_hw *hw)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>> +
>> +	/* Unreset the divider when ungating */
>> +	meson_parm_write(clk->map, &vclk->reset, 0);
>> +	meson_parm_write(clk->map, &vclk->enable, 1);
>> +
>> +	return 0;
>> +}
>> +
>> +static void clk_regmap_vclk_div_disable(struct clk_hw *hw)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>> +
>> +	/* Reset the divider when gating */
>> +	meson_parm_write(clk->map, &vclk->enable, 0);
>> +	meson_parm_write(clk->map, &vclk->reset, 1);
>> +}
>> +
>> +static int clk_regmap_vclk_div_is_enabled(struct clk_hw *hw)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>> +
>> +	return meson_parm_read(clk->map, &vclk->enable);
>> +}
>> +
>> +const struct clk_ops clk_regmap_vclk_div_ops = {
>> +	.recalc_rate = clk_regmap_vclk_div_recalc_rate,
>> +	.determine_rate = clk_regmap_vclk_div_determine_rate,
>> +	.set_rate = clk_regmap_vclk_div_set_rate,
>> +	.enable = clk_regmap_vclk_div_enable,
>> +	.disable = clk_regmap_vclk_div_disable,
>> +	.is_enabled = clk_regmap_vclk_div_is_enabled,
>> +};
>> +EXPORT_SYMBOL_GPL(clk_regmap_vclk_div_ops);
>> +
>> +MODULE_DESCRIPTION("Amlogic vclk clock driver");
>> +MODULE_AUTHOR("Neil Armstrong <neil.armstrong@linaro.org>");
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/drivers/clk/meson/vclk.h b/drivers/clk/meson/vclk.h
>> new file mode 100644
>> index 000000000000..4f25d7ad2717
>> --- /dev/null
>> +++ b/drivers/clk/meson/vclk.h
>> @@ -0,0 +1,51 @@
>> +/* SPDX-License-Identifier: GPL-2.0 */
>> +/*
>> + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
>> + */
>> +
>> +#ifndef __VCLK_H
>> +#define __VCLK_H
> 
> This is too generic.
> Please add the MESON prefix like the other clock driver please.

Ack

> 
>> +
>> +#include "clk-regmap.h"
>> +#include "parm.h"
>> +
>> +/**
>> + * struct clk_regmap_vclk_data - vclk regmap backed specific data
>> + *
>> + * @enable:	vclk enable field
>> + * @reset:	vclk reset field
>> + * @flags:	hardware-specific flags
>> + *
>> + * Flags:
>> + * Same as clk_gate except CLK_GATE_HIWORD_MASK which is ignored
>> + */
>> +struct clk_regmap_vclk_data {
>> +	struct parm enable;
>> +	struct parm reset;
>> +	u8 flags;
>> +};
>> +
>> +extern const struct clk_ops clk_regmap_vclk_ops;
>> +
>> +/**
>> + * struct clk_regmap_vclk_div_data - vclk_div regmap back specific data
>> + *
>> + * @div:	divider field
>> + * @enable:	vclk divider enable field
>> + * @reset:	vclk divider reset field
>> + * @table:	array of value/divider pairs, last entry should have div = 0
>> + *
>> + * Flags:
>> + * Same as clk_divider except CLK_DIVIDER_HIWORD_MASK which is ignored
>> + */
>> +struct clk_regmap_vclk_div_data {
>> +	struct parm div;
>> +	struct parm enable;
>> +	struct parm reset;
>> +	const struct clk_div_table *table;
>> +	u8 flags;
>> +};
>> +
>> +extern const struct clk_ops clk_regmap_vclk_div_ops;
>> +
>> +#endif /* __VCLK_H */
> 

Thanks,
Neil
Neil Armstrong Nov. 27, 2023, 4:14 p.m. UTC | #3
On 24/11/2023 15:41, Jerome Brunet wrote:
> 
> On Fri 24 Nov 2023 at 09:41, Neil Armstrong <neil.armstrong@linaro.org> wrote:
> 
>> The VCLK and VCLK_DIV clocks have supplementary bits.
>>
>> The VCLK has a "SOFT RESET" bit to toggle after the whole
>> VCLK sub-tree rate has been set, this is implemented in
>> the gate enable callback.
>>
>> The VCLK_DIV clocks as enable and reset bits used to disable
>> and reset the divider, associated with CLK_SET_RATE_GATE it ensures
>> the rate is set while the divider is disabled and in reset mode.
>>
>> The VCLK_DIV enable bit isn't implemented as a gate since it's part
>> of the divider logic and vendor does this exact sequence to ensure
>> the divider is correctly set.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>> ---
>>   drivers/clk/meson/Kconfig  |   5 ++
>>   drivers/clk/meson/Makefile |   1 +
>>   drivers/clk/meson/vclk.c   | 141 +++++++++++++++++++++++++++++++++++++++++++++
>>   drivers/clk/meson/vclk.h   |  51 ++++++++++++++++
>>   4 files changed, 198 insertions(+)
>>
>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>> index 29ffd14d267b..59a40a49f8e1 100644
>> --- a/drivers/clk/meson/Kconfig
>> +++ b/drivers/clk/meson/Kconfig
>> @@ -30,6 +30,10 @@ config COMMON_CLK_MESON_VID_PLL_DIV
>>   	tristate
>>   	select COMMON_CLK_MESON_REGMAP
>>   
>> +config COMMON_CLK_MESON_VCLK
>> +	tristate
>> +	select COMMON_CLK_MESON_REGMAP
>> +
>>   config COMMON_CLK_MESON_CLKC_UTILS
>>   	tristate
>>   
>> @@ -140,6 +144,7 @@ config COMMON_CLK_G12A
>>   	select COMMON_CLK_MESON_EE_CLKC
>>   	select COMMON_CLK_MESON_CPU_DYNDIV
>>   	select COMMON_CLK_MESON_VID_PLL_DIV
>> +	select COMMON_CLK_MESON_VCLK
> 
> This particular line belong in the next patch
> 
>>   	select MFD_SYSCON
>>   	help
>>   	  Support for the clock controller on Amlogic S905D2, S905X2 and S905Y2
>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>> index 9ee4b954c896..9ba43fe7a07a 100644
>> --- a/drivers/clk/meson/Makefile
>> +++ b/drivers/clk/meson/Makefile
>> @@ -12,6 +12,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_PLL) += clk-pll.o
>>   obj-$(CONFIG_COMMON_CLK_MESON_REGMAP) += clk-regmap.o
>>   obj-$(CONFIG_COMMON_CLK_MESON_SCLK_DIV) += sclk-div.o
>>   obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
>> +obj-$(CONFIG_COMMON_CLK_MESON_VCLK) += vclk.o
>>   
>>   # Amlogic Clock controllers
>>   
>> diff --git a/drivers/clk/meson/vclk.c b/drivers/clk/meson/vclk.c
>> new file mode 100644
>> index 000000000000..47f08a52b49f
>> --- /dev/null
>> +++ b/drivers/clk/meson/vclk.c
>> @@ -0,0 +1,141 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
>> + */
>> +
>> +#include <linux/module.h>
>> +#include "vclk.h"
>> +
>> +/* The VCLK gate has a supplementary reset bit to pulse after ungating */
>> +
>> +static inline struct clk_regmap_vclk_data *
>> +clk_get_regmap_vclk_data(struct clk_regmap *clk)
>> +{
>> +	return (struct clk_regmap_vclk_data *)clk->data;
>> +}
>> +
>> +static int clk_regmap_vclk_enable(struct clk_hw *hw)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>> +
>> +	meson_parm_write(clk->map, &vclk->enable, 1);
>> +
>> +	/* Do a reset pulse */
>> +	meson_parm_write(clk->map, &vclk->reset, 1);
>> +	meson_parm_write(clk->map, &vclk->reset, 0);
>> +
>> +	return 0;
>> +}
>> +
>> +static void clk_regmap_vclk_disable(struct clk_hw *hw)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>> +
>> +	meson_parm_write(clk->map, &vclk->enable, 0);
>> +}
>> +
>> +static int clk_regmap_vclk_is_enabled(struct clk_hw *hw)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>> +
>> +	return meson_parm_read(clk->map, &vclk->enable);
>> +}
>> +
>> +const struct clk_ops clk_regmap_vclk_ops = {
>> +	.enable = clk_regmap_vclk_enable,
>> +	.disable = clk_regmap_vclk_disable,
>> +	.is_enabled = clk_regmap_vclk_is_enabled,
>> +};
>> +EXPORT_SYMBOL_GPL(clk_regmap_vclk_ops);
> 
> s/clk_regmap_vclk/meson_vclk at least for what is exported, ideally most
> all the code.
> 
> I get clk_regmap_ comes from code copied from clk_regmap.c.
> The reason the this part is different (and not using parm) if that when
> I converted amlogic to regmap, I hope we could make this generic,
> possibly converging between aml and qcom (which was the only other
> platform using regmap for clock at the time). This is why clk_regmap.c
> is a bit different from the other driver.
> 
> For the aml specific drivers, best to look at the mpll or cpu-dyndiv one.
> 
>> +
>> +/* The VCLK Divider has supplementary reset & enable bits */
>> +
>> +static inline struct clk_regmap_vclk_div_data *
>> +clk_get_regmap_vclk_div_data(struct clk_regmap *clk)
>> +{
>> +	return (struct clk_regmap_vclk_div_data *)clk->data;
>> +}
>> +
>> +static unsigned long clk_regmap_vclk_div_recalc_rate(struct clk_hw *hw,
>> +						     unsigned long prate)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>> +
>> +	return divider_recalc_rate(hw, prate, meson_parm_read(clk->map, &vclk->div),
>> +				   vclk->table, vclk->flags, vclk->div.width);
>> +}
>> +
>> +static int clk_regmap_vclk_div_determine_rate(struct clk_hw *hw,
>> +					      struct clk_rate_request *req)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>> +
>> +	return divider_determine_rate(hw, req, vclk->table, vclk->div.width,
>> +				      vclk->flags);
>> +}
>> +
>> +static int clk_regmap_vclk_div_set_rate(struct clk_hw *hw, unsigned long rate,
>> +					unsigned long parent_rate)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>> +	int ret;
>> +
>> +	ret = divider_get_val(rate, parent_rate, vclk->table, vclk->div.width,
>> +			      vclk->flags);
>> +	if (ret < 0)
>> +		return ret;
>> +
>> +	meson_parm_write(clk->map, &vclk->div, ret);
>> +
>> +	return 0;
>> +};
>> +
>> +static int clk_regmap_vclk_div_enable(struct clk_hw *hw)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>> +
>> +	/* Unreset the divider when ungating */
>> +	meson_parm_write(clk->map, &vclk->reset, 0);
>> +	meson_parm_write(clk->map, &vclk->enable, 1);
>> +
>> +	return 0;
>> +}
>> +
>> +static void clk_regmap_vclk_div_disable(struct clk_hw *hw)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>> +
>> +	/* Reset the divider when gating */
>> +	meson_parm_write(clk->map, &vclk->enable, 0);
>> +	meson_parm_write(clk->map, &vclk->reset, 1);
>> +}
>> +
>> +static int clk_regmap_vclk_div_is_enabled(struct clk_hw *hw)
>> +{
>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>> +
>> +	return meson_parm_read(clk->map, &vclk->enable);
>> +}
>> +
>> +const struct clk_ops clk_regmap_vclk_div_ops = {
>> +	.recalc_rate = clk_regmap_vclk_div_recalc_rate,
>> +	.determine_rate = clk_regmap_vclk_div_determine_rate,
>> +	.set_rate = clk_regmap_vclk_div_set_rate,
>> +	.enable = clk_regmap_vclk_div_enable,
>> +	.disable = clk_regmap_vclk_div_disable,
>> +	.is_enabled = clk_regmap_vclk_div_is_enabled,
>> +};
>> +EXPORT_SYMBOL_GPL(clk_regmap_vclk_div_ops);
>> +
>> +MODULE_DESCRIPTION("Amlogic vclk clock driver");
>> +MODULE_AUTHOR("Neil Armstrong <neil.armstrong@linaro.org>");
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/drivers/clk/meson/vclk.h b/drivers/clk/meson/vclk.h
>> new file mode 100644
>> index 000000000000..4f25d7ad2717
>> --- /dev/null
>> +++ b/drivers/clk/meson/vclk.h

Is vclk.c/h ok ? clk-vclk doesn't look pretty, but I can switch to it to
keep files organized.

Neil

>> @@ -0,0 +1,51 @@
>> +/* SPDX-License-Identifier: GPL-2.0 */
>> +/*
>> + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
>> + */
>> +
>> +#ifndef __VCLK_H
>> +#define __VCLK_H
> 
> This is too generic.
> Please add the MESON prefix like the other clock driver please.
> 
>> +
>> +#include "clk-regmap.h"
>> +#include "parm.h"
>> +
>> +/**
>> + * struct clk_regmap_vclk_data - vclk regmap backed specific data
>> + *
>> + * @enable:	vclk enable field
>> + * @reset:	vclk reset field
>> + * @flags:	hardware-specific flags
>> + *
>> + * Flags:
>> + * Same as clk_gate except CLK_GATE_HIWORD_MASK which is ignored
>> + */
>> +struct clk_regmap_vclk_data {
>> +	struct parm enable;
>> +	struct parm reset;
>> +	u8 flags;
>> +};
>> +
>> +extern const struct clk_ops clk_regmap_vclk_ops;
>> +
>> +/**
>> + * struct clk_regmap_vclk_div_data - vclk_div regmap back specific data
>> + *
>> + * @div:	divider field
>> + * @enable:	vclk divider enable field
>> + * @reset:	vclk divider reset field
>> + * @table:	array of value/divider pairs, last entry should have div = 0
>> + *
>> + * Flags:
>> + * Same as clk_divider except CLK_DIVIDER_HIWORD_MASK which is ignored
>> + */
>> +struct clk_regmap_vclk_div_data {
>> +	struct parm div;
>> +	struct parm enable;
>> +	struct parm reset;
>> +	const struct clk_div_table *table;
>> +	u8 flags;
>> +};
>> +
>> +extern const struct clk_ops clk_regmap_vclk_div_ops;
>> +
>> +#endif /* __VCLK_H */
>
Jerome Brunet Nov. 27, 2023, 4:24 p.m. UTC | #4
On Mon 27 Nov 2023 at 17:14, Neil Armstrong <neil.armstrong@linaro.org> wrote:

> On 24/11/2023 15:41, Jerome Brunet wrote:
>> On Fri 24 Nov 2023 at 09:41, Neil Armstrong <neil.armstrong@linaro.org>
>> wrote:
>> 
>>> The VCLK and VCLK_DIV clocks have supplementary bits.
>>>
>>> The VCLK has a "SOFT RESET" bit to toggle after the whole
>>> VCLK sub-tree rate has been set, this is implemented in
>>> the gate enable callback.
>>>
>>> The VCLK_DIV clocks as enable and reset bits used to disable
>>> and reset the divider, associated with CLK_SET_RATE_GATE it ensures
>>> the rate is set while the divider is disabled and in reset mode.
>>>
>>> The VCLK_DIV enable bit isn't implemented as a gate since it's part
>>> of the divider logic and vendor does this exact sequence to ensure
>>> the divider is correctly set.
>>>
>>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>>> ---
>>>   drivers/clk/meson/Kconfig  |   5 ++
>>>   drivers/clk/meson/Makefile |   1 +
>>>   drivers/clk/meson/vclk.c   | 141 +++++++++++++++++++++++++++++++++++++++++++++
>>>   drivers/clk/meson/vclk.h   |  51 ++++++++++++++++
>>>   4 files changed, 198 insertions(+)
>>>
>>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>>> index 29ffd14d267b..59a40a49f8e1 100644
>>> --- a/drivers/clk/meson/Kconfig
>>> +++ b/drivers/clk/meson/Kconfig
>>> @@ -30,6 +30,10 @@ config COMMON_CLK_MESON_VID_PLL_DIV
>>>   	tristate
>>>   	select COMMON_CLK_MESON_REGMAP
>>>   +config COMMON_CLK_MESON_VCLK
>>> +	tristate
>>> +	select COMMON_CLK_MESON_REGMAP
>>> +
>>>   config COMMON_CLK_MESON_CLKC_UTILS
>>>   	tristate
>>>   @@ -140,6 +144,7 @@ config COMMON_CLK_G12A
>>>   	select COMMON_CLK_MESON_EE_CLKC
>>>   	select COMMON_CLK_MESON_CPU_DYNDIV
>>>   	select COMMON_CLK_MESON_VID_PLL_DIV
>>> +	select COMMON_CLK_MESON_VCLK
>> This particular line belong in the next patch
>> 
>>>   	select MFD_SYSCON
>>>   	help
>>>   	  Support for the clock controller on Amlogic S905D2, S905X2 and S905Y2
>>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>>> index 9ee4b954c896..9ba43fe7a07a 100644
>>> --- a/drivers/clk/meson/Makefile
>>> +++ b/drivers/clk/meson/Makefile
>>> @@ -12,6 +12,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_PLL) += clk-pll.o
>>>   obj-$(CONFIG_COMMON_CLK_MESON_REGMAP) += clk-regmap.o
>>>   obj-$(CONFIG_COMMON_CLK_MESON_SCLK_DIV) += sclk-div.o
>>>   obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
>>> +obj-$(CONFIG_COMMON_CLK_MESON_VCLK) += vclk.o
>>>     # Amlogic Clock controllers
>>>   diff --git a/drivers/clk/meson/vclk.c b/drivers/clk/meson/vclk.c
>>> new file mode 100644
>>> index 000000000000..47f08a52b49f
>>> --- /dev/null
>>> +++ b/drivers/clk/meson/vclk.c
>>> @@ -0,0 +1,141 @@
>>> +// SPDX-License-Identifier: GPL-2.0
>>> +/*
>>> + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
>>> + */
>>> +
>>> +#include <linux/module.h>
>>> +#include "vclk.h"
>>> +
>>> +/* The VCLK gate has a supplementary reset bit to pulse after ungating */
>>> +
>>> +static inline struct clk_regmap_vclk_data *
>>> +clk_get_regmap_vclk_data(struct clk_regmap *clk)
>>> +{
>>> +	return (struct clk_regmap_vclk_data *)clk->data;
>>> +}
>>> +
>>> +static int clk_regmap_vclk_enable(struct clk_hw *hw)
>>> +{
>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>>> +
>>> +	meson_parm_write(clk->map, &vclk->enable, 1);
>>> +
>>> +	/* Do a reset pulse */
>>> +	meson_parm_write(clk->map, &vclk->reset, 1);
>>> +	meson_parm_write(clk->map, &vclk->reset, 0);
>>> +
>>> +	return 0;
>>> +}
>>> +
>>> +static void clk_regmap_vclk_disable(struct clk_hw *hw)
>>> +{
>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>>> +
>>> +	meson_parm_write(clk->map, &vclk->enable, 0);
>>> +}
>>> +
>>> +static int clk_regmap_vclk_is_enabled(struct clk_hw *hw)
>>> +{
>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>>> +
>>> +	return meson_parm_read(clk->map, &vclk->enable);
>>> +}
>>> +
>>> +const struct clk_ops clk_regmap_vclk_ops = {
>>> +	.enable = clk_regmap_vclk_enable,
>>> +	.disable = clk_regmap_vclk_disable,
>>> +	.is_enabled = clk_regmap_vclk_is_enabled,
>>> +};
>>> +EXPORT_SYMBOL_GPL(clk_regmap_vclk_ops);
>> s/clk_regmap_vclk/meson_vclk at least for what is exported, ideally most
>> all the code.
>> I get clk_regmap_ comes from code copied from clk_regmap.c.
>> The reason the this part is different (and not using parm) if that when
>> I converted amlogic to regmap, I hope we could make this generic,
>> possibly converging between aml and qcom (which was the only other
>> platform using regmap for clock at the time). This is why clk_regmap.c
>> is a bit different from the other driver.
>> For the aml specific drivers, best to look at the mpll or cpu-dyndiv one.
>> 
>>> +
>>> +/* The VCLK Divider has supplementary reset & enable bits */
>>> +
>>> +static inline struct clk_regmap_vclk_div_data *
>>> +clk_get_regmap_vclk_div_data(struct clk_regmap *clk)
>>> +{
>>> +	return (struct clk_regmap_vclk_div_data *)clk->data;
>>> +}
>>> +
>>> +static unsigned long clk_regmap_vclk_div_recalc_rate(struct clk_hw *hw,
>>> +						     unsigned long prate)
>>> +{
>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>> +
>>> +	return divider_recalc_rate(hw, prate, meson_parm_read(clk->map, &vclk->div),
>>> +				   vclk->table, vclk->flags, vclk->div.width);
>>> +}
>>> +
>>> +static int clk_regmap_vclk_div_determine_rate(struct clk_hw *hw,
>>> +					      struct clk_rate_request *req)
>>> +{
>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>> +
>>> +	return divider_determine_rate(hw, req, vclk->table, vclk->div.width,
>>> +				      vclk->flags);
>>> +}
>>> +
>>> +static int clk_regmap_vclk_div_set_rate(struct clk_hw *hw, unsigned long rate,
>>> +					unsigned long parent_rate)
>>> +{
>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>> +	int ret;
>>> +
>>> +	ret = divider_get_val(rate, parent_rate, vclk->table, vclk->div.width,
>>> +			      vclk->flags);
>>> +	if (ret < 0)
>>> +		return ret;
>>> +
>>> +	meson_parm_write(clk->map, &vclk->div, ret);
>>> +
>>> +	return 0;
>>> +};
>>> +
>>> +static int clk_regmap_vclk_div_enable(struct clk_hw *hw)
>>> +{
>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>> +
>>> +	/* Unreset the divider when ungating */
>>> +	meson_parm_write(clk->map, &vclk->reset, 0);
>>> +	meson_parm_write(clk->map, &vclk->enable, 1);
>>> +
>>> +	return 0;
>>> +}
>>> +
>>> +static void clk_regmap_vclk_div_disable(struct clk_hw *hw)
>>> +{
>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>> +
>>> +	/* Reset the divider when gating */
>>> +	meson_parm_write(clk->map, &vclk->enable, 0);
>>> +	meson_parm_write(clk->map, &vclk->reset, 1);
>>> +}
>>> +
>>> +static int clk_regmap_vclk_div_is_enabled(struct clk_hw *hw)
>>> +{
>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>> +
>>> +	return meson_parm_read(clk->map, &vclk->enable);
>>> +}
>>> +
>>> +const struct clk_ops clk_regmap_vclk_div_ops = {
>>> +	.recalc_rate = clk_regmap_vclk_div_recalc_rate,
>>> +	.determine_rate = clk_regmap_vclk_div_determine_rate,
>>> +	.set_rate = clk_regmap_vclk_div_set_rate,
>>> +	.enable = clk_regmap_vclk_div_enable,
>>> +	.disable = clk_regmap_vclk_div_disable,
>>> +	.is_enabled = clk_regmap_vclk_div_is_enabled,
>>> +};
>>> +EXPORT_SYMBOL_GPL(clk_regmap_vclk_div_ops);
>>> +
>>> +MODULE_DESCRIPTION("Amlogic vclk clock driver");
>>> +MODULE_AUTHOR("Neil Armstrong <neil.armstrong@linaro.org>");
>>> +MODULE_LICENSE("GPL v2");
>>> diff --git a/drivers/clk/meson/vclk.h b/drivers/clk/meson/vclk.h
>>> new file mode 100644
>>> index 000000000000..4f25d7ad2717
>>> --- /dev/null
>>> +++ b/drivers/clk/meson/vclk.h
>
> Is vclk.c/h ok ? clk-vclk doesn't look pretty, but I can switch to it to
> keep files organized.

I don't have a strong opinion about it.
I would have suggested vclk-div.c/h - like sclk ... but you do have gate
ops in there, so ... :/

This made me realize that one does not really go without the other.
It is more a coherent block, isn't it ?
Would it make more sense to have these 2 merged in a single clk_ops ?

It's bit late to point this out, sorry about that.

I let you decide whether to merge the ops or not and which name to pick.

If you keep them separated, meson_vclk_gate_ops instead of just
meson_vclk_ops, to make things clear.

>
> Neil
>
>>> @@ -0,0 +1,51 @@
>>> +/* SPDX-License-Identifier: GPL-2.0 */
>>> +/*
>>> + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
>>> + */
>>> +
>>> +#ifndef __VCLK_H
>>> +#define __VCLK_H
>> This is too generic.
>> Please add the MESON prefix like the other clock driver please.
>> 
>>> +
>>> +#include "clk-regmap.h"
>>> +#include "parm.h"
>>> +
>>> +/**
>>> + * struct clk_regmap_vclk_data - vclk regmap backed specific data
>>> + *
>>> + * @enable:	vclk enable field
>>> + * @reset:	vclk reset field
>>> + * @flags:	hardware-specific flags
>>> + *
>>> + * Flags:
>>> + * Same as clk_gate except CLK_GATE_HIWORD_MASK which is ignored
>>> + */
>>> +struct clk_regmap_vclk_data {
>>> +	struct parm enable;
>>> +	struct parm reset;
>>> +	u8 flags;
>>> +};
>>> +
>>> +extern const struct clk_ops clk_regmap_vclk_ops;
>>> +
>>> +/**
>>> + * struct clk_regmap_vclk_div_data - vclk_div regmap back specific data
>>> + *
>>> + * @div:	divider field
>>> + * @enable:	vclk divider enable field
>>> + * @reset:	vclk divider reset field
>>> + * @table:	array of value/divider pairs, last entry should have div = 0
>>> + *
>>> + * Flags:
>>> + * Same as clk_divider except CLK_DIVIDER_HIWORD_MASK which is ignored
>>> + */
>>> +struct clk_regmap_vclk_div_data {
>>> +	struct parm div;
>>> +	struct parm enable;
>>> +	struct parm reset;
>>> +	const struct clk_div_table *table;
>>> +	u8 flags;
>>> +};
>>> +
>>> +extern const struct clk_ops clk_regmap_vclk_div_ops;
>>> +
>>> +#endif /* __VCLK_H */
>>
Neil Armstrong Feb. 5, 2024, 5:27 p.m. UTC | #5
On 27/11/2023 17:24, Jerome Brunet wrote:
> 
> On Mon 27 Nov 2023 at 17:14, Neil Armstrong <neil.armstrong@linaro.org> wrote:
> 
>> On 24/11/2023 15:41, Jerome Brunet wrote:
>>> On Fri 24 Nov 2023 at 09:41, Neil Armstrong <neil.armstrong@linaro.org>
>>> wrote:
>>>
>>>> The VCLK and VCLK_DIV clocks have supplementary bits.
>>>>
>>>> The VCLK has a "SOFT RESET" bit to toggle after the whole
>>>> VCLK sub-tree rate has been set, this is implemented in
>>>> the gate enable callback.
>>>>
>>>> The VCLK_DIV clocks as enable and reset bits used to disable
>>>> and reset the divider, associated with CLK_SET_RATE_GATE it ensures
>>>> the rate is set while the divider is disabled and in reset mode.
>>>>
>>>> The VCLK_DIV enable bit isn't implemented as a gate since it's part
>>>> of the divider logic and vendor does this exact sequence to ensure
>>>> the divider is correctly set.
>>>>
>>>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>>>> ---
>>>>    drivers/clk/meson/Kconfig  |   5 ++
>>>>    drivers/clk/meson/Makefile |   1 +
>>>>    drivers/clk/meson/vclk.c   | 141 +++++++++++++++++++++++++++++++++++++++++++++
>>>>    drivers/clk/meson/vclk.h   |  51 ++++++++++++++++
>>>>    4 files changed, 198 insertions(+)
>>>>
>>>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>>>> index 29ffd14d267b..59a40a49f8e1 100644
>>>> --- a/drivers/clk/meson/Kconfig
>>>> +++ b/drivers/clk/meson/Kconfig
>>>> @@ -30,6 +30,10 @@ config COMMON_CLK_MESON_VID_PLL_DIV
>>>>    	tristate
>>>>    	select COMMON_CLK_MESON_REGMAP
>>>>    +config COMMON_CLK_MESON_VCLK
>>>> +	tristate
>>>> +	select COMMON_CLK_MESON_REGMAP
>>>> +
>>>>    config COMMON_CLK_MESON_CLKC_UTILS
>>>>    	tristate
>>>>    @@ -140,6 +144,7 @@ config COMMON_CLK_G12A
>>>>    	select COMMON_CLK_MESON_EE_CLKC
>>>>    	select COMMON_CLK_MESON_CPU_DYNDIV
>>>>    	select COMMON_CLK_MESON_VID_PLL_DIV
>>>> +	select COMMON_CLK_MESON_VCLK
>>> This particular line belong in the next patch
>>>
>>>>    	select MFD_SYSCON
>>>>    	help
>>>>    	  Support for the clock controller on Amlogic S905D2, S905X2 and S905Y2
>>>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>>>> index 9ee4b954c896..9ba43fe7a07a 100644
>>>> --- a/drivers/clk/meson/Makefile
>>>> +++ b/drivers/clk/meson/Makefile
>>>> @@ -12,6 +12,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_PLL) += clk-pll.o
>>>>    obj-$(CONFIG_COMMON_CLK_MESON_REGMAP) += clk-regmap.o
>>>>    obj-$(CONFIG_COMMON_CLK_MESON_SCLK_DIV) += sclk-div.o
>>>>    obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
>>>> +obj-$(CONFIG_COMMON_CLK_MESON_VCLK) += vclk.o
>>>>      # Amlogic Clock controllers
>>>>    diff --git a/drivers/clk/meson/vclk.c b/drivers/clk/meson/vclk.c
>>>> new file mode 100644
>>>> index 000000000000..47f08a52b49f
>>>> --- /dev/null
>>>> +++ b/drivers/clk/meson/vclk.c
>>>> @@ -0,0 +1,141 @@
>>>> +// SPDX-License-Identifier: GPL-2.0
>>>> +/*
>>>> + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
>>>> + */
>>>> +
>>>> +#include <linux/module.h>
>>>> +#include "vclk.h"
>>>> +
>>>> +/* The VCLK gate has a supplementary reset bit to pulse after ungating */
>>>> +
>>>> +static inline struct clk_regmap_vclk_data *
>>>> +clk_get_regmap_vclk_data(struct clk_regmap *clk)
>>>> +{
>>>> +	return (struct clk_regmap_vclk_data *)clk->data;
>>>> +}
>>>> +
>>>> +static int clk_regmap_vclk_enable(struct clk_hw *hw)
>>>> +{
>>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>>> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>>>> +
>>>> +	meson_parm_write(clk->map, &vclk->enable, 1);
>>>> +
>>>> +	/* Do a reset pulse */
>>>> +	meson_parm_write(clk->map, &vclk->reset, 1);
>>>> +	meson_parm_write(clk->map, &vclk->reset, 0);
>>>> +
>>>> +	return 0;
>>>> +}
>>>> +
>>>> +static void clk_regmap_vclk_disable(struct clk_hw *hw)
>>>> +{
>>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>>> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>>>> +
>>>> +	meson_parm_write(clk->map, &vclk->enable, 0);
>>>> +}
>>>> +
>>>> +static int clk_regmap_vclk_is_enabled(struct clk_hw *hw)
>>>> +{
>>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>>> +	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
>>>> +
>>>> +	return meson_parm_read(clk->map, &vclk->enable);
>>>> +}
>>>> +
>>>> +const struct clk_ops clk_regmap_vclk_ops = {
>>>> +	.enable = clk_regmap_vclk_enable,
>>>> +	.disable = clk_regmap_vclk_disable,
>>>> +	.is_enabled = clk_regmap_vclk_is_enabled,
>>>> +};
>>>> +EXPORT_SYMBOL_GPL(clk_regmap_vclk_ops);
>>> s/clk_regmap_vclk/meson_vclk at least for what is exported, ideally most
>>> all the code.
>>> I get clk_regmap_ comes from code copied from clk_regmap.c.
>>> The reason the this part is different (and not using parm) if that when
>>> I converted amlogic to regmap, I hope we could make this generic,
>>> possibly converging between aml and qcom (which was the only other
>>> platform using regmap for clock at the time). This is why clk_regmap.c
>>> is a bit different from the other driver.
>>> For the aml specific drivers, best to look at the mpll or cpu-dyndiv one.
>>>
>>>> +
>>>> +/* The VCLK Divider has supplementary reset & enable bits */
>>>> +
>>>> +static inline struct clk_regmap_vclk_div_data *
>>>> +clk_get_regmap_vclk_div_data(struct clk_regmap *clk)
>>>> +{
>>>> +	return (struct clk_regmap_vclk_div_data *)clk->data;
>>>> +}
>>>> +
>>>> +static unsigned long clk_regmap_vclk_div_recalc_rate(struct clk_hw *hw,
>>>> +						     unsigned long prate)
>>>> +{
>>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>>> +
>>>> +	return divider_recalc_rate(hw, prate, meson_parm_read(clk->map, &vclk->div),
>>>> +				   vclk->table, vclk->flags, vclk->div.width);
>>>> +}
>>>> +
>>>> +static int clk_regmap_vclk_div_determine_rate(struct clk_hw *hw,
>>>> +					      struct clk_rate_request *req)
>>>> +{
>>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>>> +
>>>> +	return divider_determine_rate(hw, req, vclk->table, vclk->div.width,
>>>> +				      vclk->flags);
>>>> +}
>>>> +
>>>> +static int clk_regmap_vclk_div_set_rate(struct clk_hw *hw, unsigned long rate,
>>>> +					unsigned long parent_rate)
>>>> +{
>>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>>> +	int ret;
>>>> +
>>>> +	ret = divider_get_val(rate, parent_rate, vclk->table, vclk->div.width,
>>>> +			      vclk->flags);
>>>> +	if (ret < 0)
>>>> +		return ret;
>>>> +
>>>> +	meson_parm_write(clk->map, &vclk->div, ret);
>>>> +
>>>> +	return 0;
>>>> +};
>>>> +
>>>> +static int clk_regmap_vclk_div_enable(struct clk_hw *hw)
>>>> +{
>>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>>> +
>>>> +	/* Unreset the divider when ungating */
>>>> +	meson_parm_write(clk->map, &vclk->reset, 0);
>>>> +	meson_parm_write(clk->map, &vclk->enable, 1);
>>>> +
>>>> +	return 0;
>>>> +}
>>>> +
>>>> +static void clk_regmap_vclk_div_disable(struct clk_hw *hw)
>>>> +{
>>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>>> +
>>>> +	/* Reset the divider when gating */
>>>> +	meson_parm_write(clk->map, &vclk->enable, 0);
>>>> +	meson_parm_write(clk->map, &vclk->reset, 1);
>>>> +}
>>>> +
>>>> +static int clk_regmap_vclk_div_is_enabled(struct clk_hw *hw)
>>>> +{
>>>> +	struct clk_regmap *clk = to_clk_regmap(hw);
>>>> +	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
>>>> +
>>>> +	return meson_parm_read(clk->map, &vclk->enable);
>>>> +}
>>>> +
>>>> +const struct clk_ops clk_regmap_vclk_div_ops = {
>>>> +	.recalc_rate = clk_regmap_vclk_div_recalc_rate,
>>>> +	.determine_rate = clk_regmap_vclk_div_determine_rate,
>>>> +	.set_rate = clk_regmap_vclk_div_set_rate,
>>>> +	.enable = clk_regmap_vclk_div_enable,
>>>> +	.disable = clk_regmap_vclk_div_disable,
>>>> +	.is_enabled = clk_regmap_vclk_div_is_enabled,
>>>> +};
>>>> +EXPORT_SYMBOL_GPL(clk_regmap_vclk_div_ops);
>>>> +
>>>> +MODULE_DESCRIPTION("Amlogic vclk clock driver");
>>>> +MODULE_AUTHOR("Neil Armstrong <neil.armstrong@linaro.org>");
>>>> +MODULE_LICENSE("GPL v2");
>>>> diff --git a/drivers/clk/meson/vclk.h b/drivers/clk/meson/vclk.h
>>>> new file mode 100644
>>>> index 000000000000..4f25d7ad2717
>>>> --- /dev/null
>>>> +++ b/drivers/clk/meson/vclk.h
>>
>> Is vclk.c/h ok ? clk-vclk doesn't look pretty, but I can switch to it to
>> keep files organized.
> 
> I don't have a strong opinion about it.
> I would have suggested vclk-div.c/h - like sclk ... but you do have gate
> ops in there, so ... :/
> 
> This made me realize that one does not really go without the other.
> It is more a coherent block, isn't it ?
> Would it make more sense to have these 2 merged in a single clk_ops ?

No those a 2 separate blocks, one is for VCLK clock input and the other is for the DIV
block, and the reset isn't used in the same way so I can't merge them.

> 
> It's bit late to point this out, sorry about that.
> 
> I let you decide whether to merge the ops or not and which name to pick.
> 
> If you keep them separated, meson_vclk_gate_ops instead of just
> meson_vclk_ops, to make things clear.

Ack

> 
>>
>> Neil
>>
>>>> @@ -0,0 +1,51 @@
>>>> +/* SPDX-License-Identifier: GPL-2.0 */
>>>> +/*
>>>> + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
>>>> + */
>>>> +
>>>> +#ifndef __VCLK_H
>>>> +#define __VCLK_H
>>> This is too generic.
>>> Please add the MESON prefix like the other clock driver please.
>>>
>>>> +
>>>> +#include "clk-regmap.h"
>>>> +#include "parm.h"
>>>> +
>>>> +/**
>>>> + * struct clk_regmap_vclk_data - vclk regmap backed specific data
>>>> + *
>>>> + * @enable:	vclk enable field
>>>> + * @reset:	vclk reset field
>>>> + * @flags:	hardware-specific flags
>>>> + *
>>>> + * Flags:
>>>> + * Same as clk_gate except CLK_GATE_HIWORD_MASK which is ignored
>>>> + */
>>>> +struct clk_regmap_vclk_data {
>>>> +	struct parm enable;
>>>> +	struct parm reset;
>>>> +	u8 flags;
>>>> +};
>>>> +
>>>> +extern const struct clk_ops clk_regmap_vclk_ops;
>>>> +
>>>> +/**
>>>> + * struct clk_regmap_vclk_div_data - vclk_div regmap back specific data
>>>> + *
>>>> + * @div:	divider field
>>>> + * @enable:	vclk divider enable field
>>>> + * @reset:	vclk divider reset field
>>>> + * @table:	array of value/divider pairs, last entry should have div = 0
>>>> + *
>>>> + * Flags:
>>>> + * Same as clk_divider except CLK_DIVIDER_HIWORD_MASK which is ignored
>>>> + */
>>>> +struct clk_regmap_vclk_div_data {
>>>> +	struct parm div;
>>>> +	struct parm enable;
>>>> +	struct parm reset;
>>>> +	const struct clk_div_table *table;
>>>> +	u8 flags;
>>>> +};
>>>> +
>>>> +extern const struct clk_ops clk_regmap_vclk_div_ops;
>>>> +
>>>> +#endif /* __VCLK_H */
>>>
> 
>
diff mbox series

Patch

diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
index 29ffd14d267b..59a40a49f8e1 100644
--- a/drivers/clk/meson/Kconfig
+++ b/drivers/clk/meson/Kconfig
@@ -30,6 +30,10 @@  config COMMON_CLK_MESON_VID_PLL_DIV
 	tristate
 	select COMMON_CLK_MESON_REGMAP
 
+config COMMON_CLK_MESON_VCLK
+	tristate
+	select COMMON_CLK_MESON_REGMAP
+
 config COMMON_CLK_MESON_CLKC_UTILS
 	tristate
 
@@ -140,6 +144,7 @@  config COMMON_CLK_G12A
 	select COMMON_CLK_MESON_EE_CLKC
 	select COMMON_CLK_MESON_CPU_DYNDIV
 	select COMMON_CLK_MESON_VID_PLL_DIV
+	select COMMON_CLK_MESON_VCLK
 	select MFD_SYSCON
 	help
 	  Support for the clock controller on Amlogic S905D2, S905X2 and S905Y2
diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index 9ee4b954c896..9ba43fe7a07a 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -12,6 +12,7 @@  obj-$(CONFIG_COMMON_CLK_MESON_PLL) += clk-pll.o
 obj-$(CONFIG_COMMON_CLK_MESON_REGMAP) += clk-regmap.o
 obj-$(CONFIG_COMMON_CLK_MESON_SCLK_DIV) += sclk-div.o
 obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
+obj-$(CONFIG_COMMON_CLK_MESON_VCLK) += vclk.o
 
 # Amlogic Clock controllers
 
diff --git a/drivers/clk/meson/vclk.c b/drivers/clk/meson/vclk.c
new file mode 100644
index 000000000000..47f08a52b49f
--- /dev/null
+++ b/drivers/clk/meson/vclk.c
@@ -0,0 +1,141 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
+ */
+
+#include <linux/module.h>
+#include "vclk.h"
+
+/* The VCLK gate has a supplementary reset bit to pulse after ungating */
+
+static inline struct clk_regmap_vclk_data *
+clk_get_regmap_vclk_data(struct clk_regmap *clk)
+{
+	return (struct clk_regmap_vclk_data *)clk->data;
+}
+
+static int clk_regmap_vclk_enable(struct clk_hw *hw)
+{
+	struct clk_regmap *clk = to_clk_regmap(hw);
+	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
+
+	meson_parm_write(clk->map, &vclk->enable, 1);
+
+	/* Do a reset pulse */
+	meson_parm_write(clk->map, &vclk->reset, 1);
+	meson_parm_write(clk->map, &vclk->reset, 0);
+
+	return 0;
+}
+
+static void clk_regmap_vclk_disable(struct clk_hw *hw)
+{
+	struct clk_regmap *clk = to_clk_regmap(hw);
+	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
+
+	meson_parm_write(clk->map, &vclk->enable, 0);
+}
+
+static int clk_regmap_vclk_is_enabled(struct clk_hw *hw)
+{
+	struct clk_regmap *clk = to_clk_regmap(hw);
+	struct clk_regmap_vclk_data *vclk = clk_get_regmap_vclk_data(clk);
+
+	return meson_parm_read(clk->map, &vclk->enable);
+}
+
+const struct clk_ops clk_regmap_vclk_ops = {
+	.enable = clk_regmap_vclk_enable,
+	.disable = clk_regmap_vclk_disable,
+	.is_enabled = clk_regmap_vclk_is_enabled,
+};
+EXPORT_SYMBOL_GPL(clk_regmap_vclk_ops);
+
+/* The VCLK Divider has supplementary reset & enable bits */
+
+static inline struct clk_regmap_vclk_div_data *
+clk_get_regmap_vclk_div_data(struct clk_regmap *clk)
+{
+	return (struct clk_regmap_vclk_div_data *)clk->data;
+}
+
+static unsigned long clk_regmap_vclk_div_recalc_rate(struct clk_hw *hw,
+						     unsigned long prate)
+{
+	struct clk_regmap *clk = to_clk_regmap(hw);
+	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
+
+	return divider_recalc_rate(hw, prate, meson_parm_read(clk->map, &vclk->div),
+				   vclk->table, vclk->flags, vclk->div.width);
+}
+
+static int clk_regmap_vclk_div_determine_rate(struct clk_hw *hw,
+					      struct clk_rate_request *req)
+{
+	struct clk_regmap *clk = to_clk_regmap(hw);
+	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
+
+	return divider_determine_rate(hw, req, vclk->table, vclk->div.width,
+				      vclk->flags);
+}
+
+static int clk_regmap_vclk_div_set_rate(struct clk_hw *hw, unsigned long rate,
+					unsigned long parent_rate)
+{
+	struct clk_regmap *clk = to_clk_regmap(hw);
+	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
+	int ret;
+
+	ret = divider_get_val(rate, parent_rate, vclk->table, vclk->div.width,
+			      vclk->flags);
+	if (ret < 0)
+		return ret;
+
+	meson_parm_write(clk->map, &vclk->div, ret);
+
+	return 0;
+};
+
+static int clk_regmap_vclk_div_enable(struct clk_hw *hw)
+{
+	struct clk_regmap *clk = to_clk_regmap(hw);
+	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
+
+	/* Unreset the divider when ungating */
+	meson_parm_write(clk->map, &vclk->reset, 0);
+	meson_parm_write(clk->map, &vclk->enable, 1);
+
+	return 0;
+}
+
+static void clk_regmap_vclk_div_disable(struct clk_hw *hw)
+{
+	struct clk_regmap *clk = to_clk_regmap(hw);
+	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
+
+	/* Reset the divider when gating */
+	meson_parm_write(clk->map, &vclk->enable, 0);
+	meson_parm_write(clk->map, &vclk->reset, 1);
+}
+
+static int clk_regmap_vclk_div_is_enabled(struct clk_hw *hw)
+{
+	struct clk_regmap *clk = to_clk_regmap(hw);
+	struct clk_regmap_vclk_div_data *vclk = clk_get_regmap_vclk_div_data(clk);
+
+	return meson_parm_read(clk->map, &vclk->enable);
+}
+
+const struct clk_ops clk_regmap_vclk_div_ops = {
+	.recalc_rate = clk_regmap_vclk_div_recalc_rate,
+	.determine_rate = clk_regmap_vclk_div_determine_rate,
+	.set_rate = clk_regmap_vclk_div_set_rate,
+	.enable = clk_regmap_vclk_div_enable,
+	.disable = clk_regmap_vclk_div_disable,
+	.is_enabled = clk_regmap_vclk_div_is_enabled,
+};
+EXPORT_SYMBOL_GPL(clk_regmap_vclk_div_ops);
+
+MODULE_DESCRIPTION("Amlogic vclk clock driver");
+MODULE_AUTHOR("Neil Armstrong <neil.armstrong@linaro.org>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/clk/meson/vclk.h b/drivers/clk/meson/vclk.h
new file mode 100644
index 000000000000..4f25d7ad2717
--- /dev/null
+++ b/drivers/clk/meson/vclk.h
@@ -0,0 +1,51 @@ 
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
+ */
+
+#ifndef __VCLK_H
+#define __VCLK_H
+
+#include "clk-regmap.h"
+#include "parm.h"
+
+/**
+ * struct clk_regmap_vclk_data - vclk regmap backed specific data
+ *
+ * @enable:	vclk enable field
+ * @reset:	vclk reset field
+ * @flags:	hardware-specific flags
+ *
+ * Flags:
+ * Same as clk_gate except CLK_GATE_HIWORD_MASK which is ignored
+ */
+struct clk_regmap_vclk_data {
+	struct parm enable;
+	struct parm reset;
+	u8 flags;
+};
+
+extern const struct clk_ops clk_regmap_vclk_ops;
+
+/**
+ * struct clk_regmap_vclk_div_data - vclk_div regmap back specific data
+ *
+ * @div:	divider field
+ * @enable:	vclk divider enable field
+ * @reset:	vclk divider reset field
+ * @table:	array of value/divider pairs, last entry should have div = 0
+ *
+ * Flags:
+ * Same as clk_divider except CLK_DIVIDER_HIWORD_MASK which is ignored
+ */
+struct clk_regmap_vclk_div_data {
+	struct parm div;
+	struct parm enable;
+	struct parm reset;
+	const struct clk_div_table *table;
+	u8 flags;
+};
+
+extern const struct clk_ops clk_regmap_vclk_div_ops;
+
+#endif /* __VCLK_H */