| Message ID | 20240205194717.2056026-1-svens@stackframe.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | hw/net/tulip: add chip status register values | expand |
On 5/2/24 20:47, Sven Schnelle wrote: > Netbsd isn't able to detect a link on the emulated tulip card. That's > because netbsd reads the Chip Status Register of the Phy (address > 0x14). The default phy data in the qemu tulip driver is all zero, > which means no link is established and autonegotation isn't complete. > > Therefore set the register to 0x3b40, which means: > > Link is up, Autonegotation complete, Full Duplex, 100MBit/s Link > speed. > > Also clear the mask because this register is read only. > > Signed-off-by: Sven Schnelle <svens@stackframe.org> > --- > hw/net/tulip.c | 4 ++-- > 1 file changed, 2 insertions(+), 2 deletions(-) Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
On 2/5/24 20:47, Sven Schnelle wrote: > Netbsd isn't able to detect a link on the emulated tulip card. That's > because netbsd reads the Chip Status Register of the Phy (address > 0x14). The default phy data in the qemu tulip driver is all zero, > which means no link is established and autonegotation isn't complete. > > Therefore set the register to 0x3b40, which means: > > Link is up, Autonegotation complete, Full Duplex, 100MBit/s Link > speed. > > Also clear the mask because this register is read only. > > Signed-off-by: Sven Schnelle <svens@stackframe.org> Reviewed-by: Helge Deller <deller@gmx.de> Tested-by: Helge Deller <deller@gmx.de> Can be easily tested without installation: Download: wget https://cdn.netbsd.org/pub/NetBSD/NetBSD-9.3/iso/NetBSD-9.3-hppa.iso Run: ./qemu-system-hppa -cdrom NetBSD-9.3-hppa.iso -nographic -> a) Installation on English -> e) Utility Menu -> c) configure network Helge > --- > hw/net/tulip.c | 4 ++-- > 1 file changed, 2 insertions(+), 2 deletions(-) > > diff --git a/hw/net/tulip.c b/hw/net/tulip.c > index 6d4fb06dad..1f2ef20977 100644 > --- a/hw/net/tulip.c > +++ b/hw/net/tulip.c > @@ -421,7 +421,7 @@ static uint16_t tulip_mdi_default[] = { > /* MDI Registers 8 - 15 */ > 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, > /* MDI Registers 16 - 31 */ > - 0x0003, 0x0000, 0x0001, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, > + 0x0003, 0x0000, 0x0001, 0x0000, 0x3b40, 0x0000, 0x0000, 0x0000, > 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, > }; > > @@ -429,7 +429,7 @@ static uint16_t tulip_mdi_default[] = { > static const uint16_t tulip_mdi_mask[] = { > 0x0000, 0xffff, 0xffff, 0xffff, 0xc01f, 0xffff, 0xffff, 0x0000, > 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, > - 0x0fff, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, > + 0x0fff, 0x0000, 0xffff, 0xffff, 0x0000, 0xffff, 0xffff, 0xffff, > 0xffff, 0xffff, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, > }; >
On 2/6/24 23:33, Helge Deller wrote: > On 2/5/24 20:47, Sven Schnelle wrote: >> Netbsd isn't able to detect a link on the emulated tulip card. That's >> because netbsd reads the Chip Status Register of the Phy (address >> 0x14). The default phy data in the qemu tulip driver is all zero, >> which means no link is established and autonegotation isn't complete. >> >> Therefore set the register to 0x3b40, which means: >> >> Link is up, Autonegotation complete, Full Duplex, 100MBit/s Link >> speed. >> >> Also clear the mask because this register is read only. >> >> Signed-off-by: Sven Schnelle <svens@stackframe.org> > > Reviewed-by: Helge Deller <deller@gmx.de> > Tested-by: Helge Deller <deller@gmx.de> Unless someone complains, I'll include this patch in the upcoming hppa pull request... Helge
diff --git a/hw/net/tulip.c b/hw/net/tulip.c index 6d4fb06dad..1f2ef20977 100644 --- a/hw/net/tulip.c +++ b/hw/net/tulip.c @@ -421,7 +421,7 @@ static uint16_t tulip_mdi_default[] = { /* MDI Registers 8 - 15 */ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* MDI Registers 16 - 31 */ - 0x0003, 0x0000, 0x0001, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, + 0x0003, 0x0000, 0x0001, 0x0000, 0x3b40, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, }; @@ -429,7 +429,7 @@ static uint16_t tulip_mdi_default[] = { static const uint16_t tulip_mdi_mask[] = { 0x0000, 0xffff, 0xffff, 0xffff, 0xc01f, 0xffff, 0xffff, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, - 0x0fff, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, + 0x0fff, 0x0000, 0xffff, 0xffff, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, };
Netbsd isn't able to detect a link on the emulated tulip card. That's because netbsd reads the Chip Status Register of the Phy (address 0x14). The default phy data in the qemu tulip driver is all zero, which means no link is established and autonegotation isn't complete. Therefore set the register to 0x3b40, which means: Link is up, Autonegotation complete, Full Duplex, 100MBit/s Link speed. Also clear the mask because this register is read only. Signed-off-by: Sven Schnelle <svens@stackframe.org> --- hw/net/tulip.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)