| Message ID | 20240206051825.1038685-10-quic_kriskura@quicinc.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add multiport support for DWC3 controllers | expand |
On Tue, Feb 06, 2024 at 10:48:25AM +0530, Krishna Kurapati wrote: > Power event IRQ stat registers are present for each port > connected to controller. Add support for modifying all power event > irq stat registers present in wrapper. > > Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Regards, Bjorn > --- > drivers/usb/dwc3/dwc3-qcom.c | 30 +++++++++++++++++++++++------- > 1 file changed, 23 insertions(+), 7 deletions(-) > > diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c > index 572dc3fdae12..e789745a9468 100644 > --- a/drivers/usb/dwc3/dwc3-qcom.c > +++ b/drivers/usb/dwc3/dwc3-qcom.c > @@ -37,7 +37,11 @@ > #define PIPE3_PHYSTATUS_SW BIT(3) > #define PIPE_UTMI_CLK_DIS BIT(8) > > -#define PWR_EVNT_IRQ_STAT_REG 0x58 > +#define PWR_EVNT_IRQ1_STAT_REG 0x58 > +#define PWR_EVNT_IRQ2_STAT_REG 0x1dc > +#define PWR_EVNT_IRQ3_STAT_REG 0x228 > +#define PWR_EVNT_IRQ4_STAT_REG 0x238 > + > #define PWR_EVNT_LPM_IN_L2_MASK BIT(4) > #define PWR_EVNT_LPM_OUT_L2_MASK BIT(5) > > @@ -109,6 +113,13 @@ struct dwc3_qcom { > u8 num_ports; > }; > > +static const u32 pwr_evnt_irq_stat_reg_offset[DWC3_MAX_PORTS] = { > + PWR_EVNT_IRQ1_STAT_REG, > + PWR_EVNT_IRQ2_STAT_REG, > + PWR_EVNT_IRQ3_STAT_REG, > + PWR_EVNT_IRQ4_STAT_REG, > +}; > + > static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val) > { > u32 reg; > @@ -444,9 +455,11 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom, bool wakeup) > if (qcom->is_suspended) > return 0; > > - val = readl(qcom->qscratch_base + PWR_EVNT_IRQ_STAT_REG); > - if (!(val & PWR_EVNT_LPM_IN_L2_MASK)) > - dev_err(qcom->dev, "HS-PHY not in L2\n"); > + for (i = 0; i < qcom->num_ports; i++) { > + val = readl(qcom->qscratch_base + pwr_evnt_irq_stat_reg_offset[i]); > + if (!(val & PWR_EVNT_LPM_IN_L2_MASK)) > + dev_err(qcom->dev, "Port-%d HS-PHY not in L2\n", i + 1); > + } > > for (i = qcom->num_clocks - 1; i >= 0; i--) > clk_disable_unprepare(qcom->clks[i]); > @@ -491,9 +504,12 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom, bool wakeup) > if (ret) > dev_warn(qcom->dev, "failed to enable interconnect: %d\n", ret); > > - /* Clear existing events from PHY related to L2 in/out */ > - dwc3_qcom_setbits(qcom->qscratch_base, PWR_EVNT_IRQ_STAT_REG, > - PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK); > + for (i = 0; i < qcom->num_ports; i++) { > + /* Clear existing events from PHY related to L2 in/out */ > + dwc3_qcom_setbits(qcom->qscratch_base, > + pwr_evnt_irq_stat_reg_offset[i], > + PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK); > + } > > qcom->is_suspended = false; > > -- > 2.34.1 >
On Tue, Feb 06, 2024, Krishna Kurapati wrote: > Power event IRQ stat registers are present for each port > connected to controller. Add support for modifying all power event > irq stat registers present in wrapper. > > Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> > --- > drivers/usb/dwc3/dwc3-qcom.c | 30 +++++++++++++++++++++++------- > 1 file changed, 23 insertions(+), 7 deletions(-) > > diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c > index 572dc3fdae12..e789745a9468 100644 > --- a/drivers/usb/dwc3/dwc3-qcom.c > +++ b/drivers/usb/dwc3/dwc3-qcom.c > @@ -37,7 +37,11 @@ > #define PIPE3_PHYSTATUS_SW BIT(3) > #define PIPE_UTMI_CLK_DIS BIT(8) > > -#define PWR_EVNT_IRQ_STAT_REG 0x58 > +#define PWR_EVNT_IRQ1_STAT_REG 0x58 > +#define PWR_EVNT_IRQ2_STAT_REG 0x1dc > +#define PWR_EVNT_IRQ3_STAT_REG 0x228 > +#define PWR_EVNT_IRQ4_STAT_REG 0x238 > + > #define PWR_EVNT_LPM_IN_L2_MASK BIT(4) > #define PWR_EVNT_LPM_OUT_L2_MASK BIT(5) > > @@ -109,6 +113,13 @@ struct dwc3_qcom { > u8 num_ports; > }; > > +static const u32 pwr_evnt_irq_stat_reg_offset[DWC3_MAX_PORTS] = { > + PWR_EVNT_IRQ1_STAT_REG, > + PWR_EVNT_IRQ2_STAT_REG, > + PWR_EVNT_IRQ3_STAT_REG, > + PWR_EVNT_IRQ4_STAT_REG, > +}; > + > static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val) > { > u32 reg; > @@ -444,9 +455,11 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom, bool wakeup) > if (qcom->is_suspended) > return 0; > > - val = readl(qcom->qscratch_base + PWR_EVNT_IRQ_STAT_REG); > - if (!(val & PWR_EVNT_LPM_IN_L2_MASK)) > - dev_err(qcom->dev, "HS-PHY not in L2\n"); > + for (i = 0; i < qcom->num_ports; i++) { > + val = readl(qcom->qscratch_base + pwr_evnt_irq_stat_reg_offset[i]); > + if (!(val & PWR_EVNT_LPM_IN_L2_MASK)) > + dev_err(qcom->dev, "Port-%d HS-PHY not in L2\n", i + 1); > + } > > for (i = qcom->num_clocks - 1; i >= 0; i--) > clk_disable_unprepare(qcom->clks[i]); > @@ -491,9 +504,12 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom, bool wakeup) > if (ret) > dev_warn(qcom->dev, "failed to enable interconnect: %d\n", ret); > > - /* Clear existing events from PHY related to L2 in/out */ > - dwc3_qcom_setbits(qcom->qscratch_base, PWR_EVNT_IRQ_STAT_REG, > - PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK); > + for (i = 0; i < qcom->num_ports; i++) { > + /* Clear existing events from PHY related to L2 in/out */ > + dwc3_qcom_setbits(qcom->qscratch_base, > + pwr_evnt_irq_stat_reg_offset[i], > + PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK); > + } > > qcom->is_suspended = false; > > -- > 2.34.1 > Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> BR, Thinh
diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c index 572dc3fdae12..e789745a9468 100644 --- a/drivers/usb/dwc3/dwc3-qcom.c +++ b/drivers/usb/dwc3/dwc3-qcom.c @@ -37,7 +37,11 @@ #define PIPE3_PHYSTATUS_SW BIT(3) #define PIPE_UTMI_CLK_DIS BIT(8) -#define PWR_EVNT_IRQ_STAT_REG 0x58 +#define PWR_EVNT_IRQ1_STAT_REG 0x58 +#define PWR_EVNT_IRQ2_STAT_REG 0x1dc +#define PWR_EVNT_IRQ3_STAT_REG 0x228 +#define PWR_EVNT_IRQ4_STAT_REG 0x238 + #define PWR_EVNT_LPM_IN_L2_MASK BIT(4) #define PWR_EVNT_LPM_OUT_L2_MASK BIT(5) @@ -109,6 +113,13 @@ struct dwc3_qcom { u8 num_ports; }; +static const u32 pwr_evnt_irq_stat_reg_offset[DWC3_MAX_PORTS] = { + PWR_EVNT_IRQ1_STAT_REG, + PWR_EVNT_IRQ2_STAT_REG, + PWR_EVNT_IRQ3_STAT_REG, + PWR_EVNT_IRQ4_STAT_REG, +}; + static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val) { u32 reg; @@ -444,9 +455,11 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom, bool wakeup) if (qcom->is_suspended) return 0; - val = readl(qcom->qscratch_base + PWR_EVNT_IRQ_STAT_REG); - if (!(val & PWR_EVNT_LPM_IN_L2_MASK)) - dev_err(qcom->dev, "HS-PHY not in L2\n"); + for (i = 0; i < qcom->num_ports; i++) { + val = readl(qcom->qscratch_base + pwr_evnt_irq_stat_reg_offset[i]); + if (!(val & PWR_EVNT_LPM_IN_L2_MASK)) + dev_err(qcom->dev, "Port-%d HS-PHY not in L2\n", i + 1); + } for (i = qcom->num_clocks - 1; i >= 0; i--) clk_disable_unprepare(qcom->clks[i]); @@ -491,9 +504,12 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom, bool wakeup) if (ret) dev_warn(qcom->dev, "failed to enable interconnect: %d\n", ret); - /* Clear existing events from PHY related to L2 in/out */ - dwc3_qcom_setbits(qcom->qscratch_base, PWR_EVNT_IRQ_STAT_REG, - PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK); + for (i = 0; i < qcom->num_ports; i++) { + /* Clear existing events from PHY related to L2 in/out */ + dwc3_qcom_setbits(qcom->qscratch_base, + pwr_evnt_irq_stat_reg_offset[i], + PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK); + } qcom->is_suspended = false;
Power event IRQ stat registers are present for each port connected to controller. Add support for modifying all power event irq stat registers present in wrapper. Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> --- drivers/usb/dwc3/dwc3-qcom.c | 30 +++++++++++++++++++++++------- 1 file changed, 23 insertions(+), 7 deletions(-)