| Message ID | 20240212140331.915498-2-tudor.ambarus@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | spi: s3c64xx: remove OF alias ID dependency | expand |
On Mon, 12 Feb 2024 14:03:20 +0000, Tudor Ambarus wrote: > There are SPI IPs that can be configured by the integrator with a > specific FIFO depth depending on the system's capabilities. For example, > the samsung USI SPI IP can be configured by the integrator with a TX/RX > FIFO from 8 byte to 256 bytes. > > Introduce the ``fifo-depth`` property for such instances of IPs where the > same FIFO depth is used for both RX and TX. Introduce ``rx-fifo-depth`` > and ``tx-fifo-depth`` properties for cases where the RX FIFO depth is > different from the TX FIFO depth. > > Make the dedicated RX/TX properties dependent on each other and mutual > exclusive with the other. > > Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org> > --- > .../bindings/spi/spi-controller.yaml | 27 +++++++++++++++++++ > 1 file changed, 27 insertions(+) > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: ./Documentation/devicetree/bindings/spi/spi-controller.yaml:152:9: [warning] wrong indentation: expected 6 but found 8 (indentation) ./Documentation/devicetree/bindings/spi/spi-controller.yaml:156:9: [warning] wrong indentation: expected 6 but found 8 (indentation) dtschema/dtc warnings/errors: doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20240212140331.915498-2-tudor.ambarus@linaro.org The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema.
On 12.02.2024 17:36, Rob Herring wrote: > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > on your patch (DT_CHECKER_FLAGS is new in v5.13): > > yamllint warnings/errors: > ./Documentation/devicetree/bindings/spi/spi-controller.yaml:152:9: > [warning] wrong indentation: expected 6 but found 8 (indentation) > ./Documentation/devicetree/bindings/spi/spi-controller.yaml:156:9: > [warning] wrong indentation: expected 6 but found 8 (indentation) > > dtschema/dtc warnings/errors: oh, the horror, I missed these. I'll re-check and resend. Thanks, ta
On Mon, Feb 12, 2024 at 02:03:20PM +0000, Tudor Ambarus wrote: > There are SPI IPs that can be configured by the integrator with a > specific FIFO depth depending on the system's capabilities. For example, > the samsung USI SPI IP can be configured by the integrator with a TX/RX > FIFO from 8 byte to 256 bytes. > > Introduce the ``fifo-depth`` property for such instances of IPs where the > same FIFO depth is used for both RX and TX. Introduce ``rx-fifo-depth`` > and ``tx-fifo-depth`` properties for cases where the RX FIFO depth is > different from the TX FIFO depth. > > Make the dedicated RX/TX properties dependent on each other and mutual > exclusive with the other. > > Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org> > --- > .../bindings/spi/spi-controller.yaml | 27 +++++++++++++++++++ > 1 file changed, 27 insertions(+) With the indentation fixed, Reviewed-by: Rob Herring <robh@kernel.org>
Hi Tudor, kernel test robot noticed the following build warnings: [auto build test WARNING on broonie-spi/for-next] [also build test WARNING on robh/for-next linus/master v6.8-rc4 next-20240216] [cannot apply to krzk/for-next] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch#_base_tree_information] url: https://github.com/intel-lab-lkp/linux/commits/Tudor-Ambarus/spi-dt-bindings-introduce-FIFO-depth-properties/20240212-221427 base: https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next patch link: https://lore.kernel.org/r/20240212140331.915498-2-tudor.ambarus%40linaro.org patch subject: [PATCH v2 01/12] spi: dt-bindings: introduce FIFO depth properties compiler: loongarch64-linux-gcc (GCC) 13.2.0 reproduce: (https://download.01.org/0day-ci/archive/20240216/202402161543.5JdIODY4-lkp@intel.com/reproduce) If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags | Reported-by: kernel test robot <lkp@intel.com> | Closes: https://lore.kernel.org/oe-kbuild-all/202402161543.5JdIODY4-lkp@intel.com/ dtcheck warnings: (new ones prefixed by >>) >> Documentation/devicetree/bindings/spi/spi-controller.yaml:152:9: [warning] wrong indentation: expected 6 but found 8 (indentation) Documentation/devicetree/bindings/spi/spi-controller.yaml:156:9: [warning] wrong indentation: expected 6 but found 8 (indentation) vim +152 Documentation/devicetree/bindings/spi/spi-controller.yaml 8 9 maintainers: 10 - Mark Brown <broonie@kernel.org> 11 12 description: | 13 SPI busses can be described with a node for the SPI controller device 14 and a set of child nodes for each SPI slave on the bus. The system SPI 15 controller may be described for use in SPI master mode or in SPI slave mode, 16 but not for both at the same time. 17 18 properties: 19 $nodename: 20 pattern: "^spi(@.*|-([0-9]|[1-9][0-9]+))?$" 21 22 "#address-cells": 23 enum: [0, 1] 24 25 "#size-cells": 26 const: 0 27 28 cs-gpios: 29 description: | 30 GPIOs used as chip selects. 31 If that property is used, the number of chip selects will be 32 increased automatically with max(cs-gpios, hardware chip selects). 33 34 So if, for example, the controller has 4 CS lines, and the 35 cs-gpios looks like this 36 cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>; 37 38 Then it should be configured so that num_chipselect = 4, with 39 the following mapping 40 cs0 : &gpio1 0 0 41 cs1 : native 42 cs2 : &gpio1 1 0 43 cs3 : &gpio1 2 0 44 45 The second flag of a gpio descriptor can be GPIO_ACTIVE_HIGH (0) 46 or GPIO_ACTIVE_LOW(1). Legacy device trees often use 0. 47 48 There is a special rule set for combining the second flag of an 49 cs-gpio with the optional spi-cs-high flag for SPI slaves. 50 51 Each table entry defines how the CS pin is to be physically 52 driven (not considering potential gpio inversions by pinmux): 53 54 device node | cs-gpio | CS pin state active | Note 55 ================+===============+=====================+===== 56 spi-cs-high | - | H | 57 - | - | L | 58 spi-cs-high | ACTIVE_HIGH | H | 59 - | ACTIVE_HIGH | L | 1 60 spi-cs-high | ACTIVE_LOW | H | 2 61 - | ACTIVE_LOW | L | 62 63 Notes: 64 1) Should print a warning about polarity inversion. 65 Here it would be wise to avoid and define the gpio as 66 ACTIVE_LOW. 67 2) Should print a warning about polarity inversion 68 because ACTIVE_LOW is overridden by spi-cs-high. 69 Should be generally avoided and be replaced by 70 spi-cs-high + ACTIVE_HIGH. 71 72 fifo-depth: 73 $ref: /schemas/types.yaml#/definitions/uint32 74 description: 75 Size of the RX and TX data FIFOs in bytes. 76 77 rx-fifo-depth: 78 $ref: /schemas/types.yaml#/definitions/uint32 79 description: 80 Size of the RX data FIFO in bytes. 81 82 tx-fifo-depth: 83 $ref: /schemas/types.yaml#/definitions/uint32 84 description: 85 Size of the TX data FIFO in bytes. 86 87 num-cs: 88 $ref: /schemas/types.yaml#/definitions/uint32 89 description: 90 Total number of chip selects. 91 92 spi-slave: 93 $ref: /schemas/types.yaml#/definitions/flag 94 description: 95 The SPI controller acts as a slave, instead of a master. 96 97 slave: 98 type: object 99 100 properties: 101 compatible: 102 description: 103 Compatible of the SPI device. 104 105 required: 106 - compatible 107 108 patternProperties: 109 "^.*@[0-9a-f]+$": 110 type: object 111 $ref: spi-peripheral-props.yaml 112 additionalProperties: true 113 114 properties: 115 spi-3wire: 116 $ref: /schemas/types.yaml#/definitions/flag 117 description: 118 The device requires 3-wire mode. 119 120 spi-cpha: 121 $ref: /schemas/types.yaml#/definitions/flag 122 description: 123 The device requires shifted clock phase (CPHA) mode. 124 125 spi-cpol: 126 $ref: /schemas/types.yaml#/definitions/flag 127 description: 128 The device requires inverse clock polarity (CPOL) mode. 129 130 required: 131 - compatible 132 - reg 133 134 dependencies: 135 rx-fifo-depth: [ tx-fifo-depth ] 136 tx-fifo-depth: [ rx-fifo-depth ] 137 138 allOf: 139 - if: 140 not: 141 required: 142 - spi-slave 143 then: 144 properties: 145 "#address-cells": 146 const: 1 147 else: 148 properties: 149 "#address-cells": 150 const: 0 151 - not: > 152 required: 153 - fifo-depth 154 - rx-fifo-depth 155 - not: 156 required: 157 - fifo-depth 158 - tx-fifo-depth 159
diff --git a/Documentation/devicetree/bindings/spi/spi-controller.yaml b/Documentation/devicetree/bindings/spi/spi-controller.yaml index 524f6fe8c27b..add39884d226 100644 --- a/Documentation/devicetree/bindings/spi/spi-controller.yaml +++ b/Documentation/devicetree/bindings/spi/spi-controller.yaml @@ -69,6 +69,21 @@ properties: Should be generally avoided and be replaced by spi-cs-high + ACTIVE_HIGH. + fifo-depth: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Size of the RX and TX data FIFOs in bytes. + + rx-fifo-depth: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Size of the RX data FIFO in bytes. + + tx-fifo-depth: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Size of the TX data FIFO in bytes. + num-cs: $ref: /schemas/types.yaml#/definitions/uint32 description: @@ -116,6 +131,10 @@ patternProperties: - compatible - reg +dependencies: + rx-fifo-depth: [ tx-fifo-depth ] + tx-fifo-depth: [ rx-fifo-depth ] + allOf: - if: not: @@ -129,6 +148,14 @@ allOf: properties: "#address-cells": const: 0 + - not: + required: + - fifo-depth + - rx-fifo-depth + - not: + required: + - fifo-depth + - tx-fifo-depth additionalProperties: true
There are SPI IPs that can be configured by the integrator with a specific FIFO depth depending on the system's capabilities. For example, the samsung USI SPI IP can be configured by the integrator with a TX/RX FIFO from 8 byte to 256 bytes. Introduce the ``fifo-depth`` property for such instances of IPs where the same FIFO depth is used for both RX and TX. Introduce ``rx-fifo-depth`` and ``tx-fifo-depth`` properties for cases where the RX FIFO depth is different from the TX FIFO depth. Make the dedicated RX/TX properties dependent on each other and mutual exclusive with the other. Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org> --- .../bindings/spi/spi-controller.yaml | 27 +++++++++++++++++++ 1 file changed, 27 insertions(+)