@@ -2223,16 +2223,16 @@ static int e1000e_get_eee(struct net_device *netdev, struct ethtool_keee *edata)
ret_val = e1000_read_emi_reg_locked(hw, cap_addr, &phy_data);
if (ret_val)
goto release;
- edata->supported_u32 = mmd_eee_cap_to_ethtool_sup_t(phy_data);
+ mii_eee_cap1_mod_linkmode_t(edata->supported, phy_data);
/* EEE Advertised */
- edata->advertised_u32 = mmd_eee_adv_to_ethtool_adv_t(adapter->eee_advert);
+ mii_eee_cap1_mod_linkmode_t(edata->advertised, adapter->eee_advert);
/* EEE Link Partner Advertised */
ret_val = e1000_read_emi_reg_locked(hw, lpa_addr, &phy_data);
if (ret_val)
goto release;
- edata->lp_advertised_u32 = mmd_eee_adv_to_ethtool_adv_t(phy_data);
+ mii_eee_cap1_mod_linkmode_t(edata->lp_advertised, phy_data);
/* EEE PCS Status */
ret_val = e1000_read_emi_reg_locked(hw, pcs_stat_addr, &phy_data);
@@ -2265,6 +2265,8 @@ static int e1000e_get_eee(struct net_device *netdev, struct ethtool_keee *edata)
static int e1000e_set_eee(struct net_device *netdev, struct ethtool_keee *edata)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(supported) = {};
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(tmp) = {};
struct e1000_hw *hw = &adapter->hw;
struct ethtool_keee eee_curr;
s32 ret_val;
@@ -2283,12 +2285,17 @@ static int e1000e_set_eee(struct net_device *netdev, struct ethtool_keee *edata)
return -EINVAL;
}
- if (edata->advertised_u32 & ~(ADVERTISE_100_FULL | ADVERTISE_1000_FULL)) {
+ linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT,
+ supported);
+ linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT,
+ supported);
+
+ if (linkmode_andnot(tmp, edata->advertised, supported)) {
e_err("EEE advertisement supports only 100TX and/or 1000T full-duplex\n");
return -EINVAL;
}
- adapter->eee_advert = ethtool_adv_to_mmd_eee_adv_t(edata->advertised_u32);
+ adapter->eee_advert = linkmode_to_mii_eee_cap1_t(edata->advertised);
hw->dev_spec.ich8lan.eee_disable = !edata->eee_enabled;
Make use of the existing linkmode helpers for converting PHY EEE register values into links modes, now that ethtool_keee uses link modes, rather than u32 values. Signed-off-by: Andrew Lunn <andrew@lunn.ch> --- drivers/net/ethernet/intel/e1000e/ethtool.c | 17 ++++++++++++----- 1 file changed, 12 insertions(+), 5 deletions(-)