| Message ID | 20240220135946.4028553-2-mathias.nyman@linux.intel.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [RFT,v2,1/2] usb: usb-acpi: Set port connect type of not connectable ports correctly | expand |
[CC: +Mike, +Hans, +Kai-Heng] Dear Mathias, Thank you for sending out v2. Am 20.02.24 um 14:59 schrieb Mathias Nyman: > Unused USB ports may have bogus location data in ACPI PLD tables. > This causes port peering failures as these unused USB2 and USB3 ports > location may match. > > This is seen on DELL systems where all unused ports return zeroed > location data. > > Don't try to peer or match ports that have connect type set to > USB_PORT_NOT_USED. > > Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> > --- > v1 -> v2 > Don't try to peer unused ports instead of reacting to failed peering > > drivers/usb/core/port.c | 5 +++-- > 1 file changed, 3 insertions(+), 2 deletions(-) > > diff --git a/drivers/usb/core/port.c b/drivers/usb/core/port.c > index c628c1abc907..4d63496f98b6 100644 > --- a/drivers/usb/core/port.c > +++ b/drivers/usb/core/port.c > @@ -573,7 +573,7 @@ static int match_location(struct usb_device *peer_hdev, void *p) > struct usb_hub *peer_hub = usb_hub_to_struct_hub(peer_hdev); > struct usb_device *hdev = to_usb_device(port_dev->dev.parent->parent); > > - if (!peer_hub) > + if (!peer_hub || port_dev->connect_type == USB_PORT_NOT_USED) > return 0; > > hcd = bus_to_hcd(hdev->bus); > @@ -584,7 +584,8 @@ static int match_location(struct usb_device *peer_hdev, void *p) > > for (port1 = 1; port1 <= peer_hdev->maxchild; port1++) { > peer = peer_hub->ports[port1 - 1]; > - if (peer && peer->location == port_dev->location) { > + if (peer && peer->connect_type != USB_PORT_NOT_USED && > + peer->location == port_dev->location) { > link_peers_report(port_dev, peer); > return 1; /* done */ > } On the Dell XPS 13 9360/0596KF, BIOS 2.21.0 06/02/2022, the warning is also gone with v2 of your patches. $ git log --no-decorate --oneline -3 adfad858cb43 usb: port: Don't try to peer unused USB ports based on location 0dd7982708bb usb: usb-acpi: Set port connect type of not connectable ports correctly 9fc1ccccfd8d Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma Please find the Linux messages with `usbcore.dyndbg=+p` attached. Thank you again for taking this on so quickly and diligently. Kind regards, Paul [ 0.000000] Linux version 6.8.0-rc5+ (build@bohemianrhapsody.molgen.mpg.de) (gcc (Debian 13.2.0-13) 13.2.0, GNU ld (GNU Binutils for Debian) 2.42) #27 SMP PREEMPT_DYNAMIC Wed Feb 21 09:09:49 CET 2024 [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-6.8.0-rc5+ root=UUID=32e29882-d94d-4a92-9ee4-4d03002bfa29 ro quiet pci=noaer mem_sleep_default=deep log_buf_len=8M cryptomgr.notests usbcore.dyndbg=+p [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000057fff] usable [ 0.000000] BIOS-e820: [mem 0x0000000000058000-0x0000000000058fff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000059000-0x000000000009dfff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009e000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000556aafff] usable [ 0.000000] BIOS-e820: [mem 0x00000000556ab000-0x00000000556abfff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000556ac000-0x00000000556acfff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000556ad000-0x0000000064df3fff] usable [ 0.000000] BIOS-e820: [mem 0x0000000064df4000-0x000000006517ffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000065180000-0x00000000651c3fff] ACPI data [ 0.000000] BIOS-e820: [mem 0x00000000651c4000-0x000000006f871fff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x000000006f872000-0x000000006fffefff] reserved [ 0.000000] BIOS-e820: [mem 0x000000006ffff000-0x000000006fffffff] usable [ 0.000000] BIOS-e820: [mem 0x0000000070000000-0x0000000077ffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000078000000-0x00000000785fffff] usable [ 0.000000] BIOS-e820: [mem 0x0000000078600000-0x000000007c7fffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fe000000-0x00000000fe010fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x00000004817fffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] e820: update [mem 0x514e7018-0x514f7057] usable ==> usable [ 0.000000] e820: update [mem 0x514e7018-0x514f7057] usable ==> usable [ 0.000000] extended physical RAM map: [ 0.000000] reserve setup_data: [mem 0x0000000000000000-0x0000000000057fff] usable [ 0.000000] reserve setup_data: [mem 0x0000000000058000-0x0000000000058fff] reserved [ 0.000000] reserve setup_data: [mem 0x0000000000059000-0x000000000009dfff] usable [ 0.000000] reserve setup_data: [mem 0x000000000009e000-0x00000000000fffff] reserved [ 0.000000] reserve setup_data: [mem 0x0000000000100000-0x00000000514e7017] usable [ 0.000000] reserve setup_data: [mem 0x00000000514e7018-0x00000000514f7057] usable [ 0.000000] reserve setup_data: [mem 0x00000000514f7058-0x00000000556aafff] usable [ 0.000000] reserve setup_data: [mem 0x00000000556ab000-0x00000000556abfff] ACPI NVS [ 0.000000] reserve setup_data: [mem 0x00000000556ac000-0x00000000556acfff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000556ad000-0x0000000064df3fff] usable [ 0.000000] reserve setup_data: [mem 0x0000000064df4000-0x000000006517ffff] reserved [ 0.000000] reserve setup_data: [mem 0x0000000065180000-0x00000000651c3fff] ACPI data [ 0.000000] reserve setup_data: [mem 0x00000000651c4000-0x000000006f871fff] ACPI NVS [ 0.000000] reserve setup_data: [mem 0x000000006f872000-0x000000006fffefff] reserved [ 0.000000] reserve setup_data: [mem 0x000000006ffff000-0x000000006fffffff] usable [ 0.000000] reserve setup_data: [mem 0x0000000070000000-0x0000000077ffffff] reserved [ 0.000000] reserve setup_data: [mem 0x0000000078000000-0x00000000785fffff] usable [ 0.000000] reserve setup_data: [mem 0x0000000078600000-0x000000007c7fffff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000e0000000-0x00000000efffffff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000fe000000-0x00000000fe010fff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000fee00000-0x00000000fee00fff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000ff000000-0x00000000ffffffff] reserved [ 0.000000] reserve setup_data: [mem 0x0000000100000000-0x00000004817fffff] usable [ 0.000000] efi: EFI v2.4 by American Megatrends [ 0.000000] efi: ACPI=0x6518d000 ACPI 2.0=0x6518d000 SMBIOS=0xf0000 SMBIOS 3.0=0xf0020 TPMFinalLog=0x6f812000 ESRT=0x6fc86698 MEMATTR=0x62675018 INITRD=0x5577da98 TPMEventLog=0x5577e018 [ 0.000000] efi: Remove mem34: MMIO range=[0xe0000000-0xefffffff] (256MB) from e820 map [ 0.000000] e820: remove [mem 0xe0000000-0xefffffff] reserved [ 0.000000] efi: Not removing mem35: MMIO range=[0xfe000000-0xfe010fff] (68KB) from e820 map [ 0.000000] efi: Not removing mem36: MMIO range=[0xfec00000-0xfec00fff] (4KB) from e820 map [ 0.000000] efi: Not removing mem37: MMIO range=[0xfee00000-0xfee00fff] (4KB) from e820 map [ 0.000000] efi: Remove mem38: MMIO range=[0xff000000-0xffffffff] (16MB) from e820 map [ 0.000000] e820: remove [mem 0xff000000-0xffffffff] reserved [ 0.000000] SMBIOS 3.0.0 present. [ 0.000000] DMI: Dell Inc. XPS 13 9360/0596KF, BIOS 2.21.0 06/02/2022 [ 0.000000] tsc: Detected 2900.000 MHz processor [ 0.000000] tsc: Detected 2899.886 MHz TSC [ 0.000752] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000754] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000762] last_pfn = 0x481800 max_arch_pfn = 0x400000000 [ 0.000766] MTRR map: 4 entries (3 fixed + 1 variable; max 23), built from 10 variable MTRRs [ 0.000767] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT [ 0.001093] last_pfn = 0x78600 max_arch_pfn = 0x400000000 [ 0.007613] esrt: Reserving ESRT space from 0x000000006fc86698 to 0x000000006fc866d0. [ 0.007617] Using GB pages for direct mapping [ 0.013962] printk: log_buf_len: 8388608 bytes [ 0.013963] printk: early log buf free: 125328(95%) [ 0.013964] Secure boot disabled [ 0.013964] RAMDISK: [mem 0x514f8000-0x52766fff] [ 0.013968] ACPI: Early table checksum verification disabled [ 0.013972] ACPI: RSDP 0x000000006518D000 000024 (v02 DELL ) [ 0.013975] ACPI: XSDT 0x000000006518D0C8 00010C (v01 DELL CBX3 01072009 AMI 00010013) [ 0.013981] ACPI: FACP 0x00000000651B2A48 00010C (v05 DELL CBX3 01072009 AMI 00010013) [ 0.013985] ACPI: DSDT 0x000000006518D260 0257E7 (v02 DELL CBX3 01072009 INTL 20160422) [ 0.013988] ACPI: FACS 0x000000006F86F180 000040 [ 0.013990] ACPI: APIC 0x00000000651B2B58 000084 (v03 DELL CBX3 01072009 AMI 00010013) [ 0.013993] ACPI: FPDT 0x00000000651B2BE0 000044 (v01 DELL CBX3 01072009 AMI 00010013) [ 0.013995] ACPI: FIDT 0x00000000651B2C28 0000AC (v01 DELL CBX3 01072009 AMI 00010013) [ 0.013998] ACPI: MCFG 0x00000000651B2CD8 00003C (v01 DELL CBX3 01072009 MSFT 00000097) [ 0.014000] ACPI: HPET 0x00000000651B2D18 000038 (v01 DELL CBX3 01072009 AMI. 0005000B) [ 0.014003] ACPI: SSDT 0x00000000651B2D50 000359 (v01 SataRe SataTabl 00001000 INTL 20160422) [ 0.014006] ACPI: BOOT 0x00000000651B30B0 000028 (v01 DELL CBX3 01072009 AMI 00010013) [ 0.014008] ACPI: SSDT 0x00000000651B30D8 0012CF (v02 SaSsdt SaSsdt 00003000 INTL 20160422) [ 0.014011] ACPI: HPET 0x00000000651B43A8 000038 (v01 INTEL KBL-ULT 00000001 MSFT 0000005F) [ 0.014013] ACPI: SSDT 0x00000000651B43E0 000D84 (v02 INTEL xh_rvp07 00000000 INTL 20160422) [ 0.014016] ACPI: UEFI 0x00000000651B5168 000042 (v01 00000000 00000000) [ 0.014019] ACPI: SSDT 0x00000000651B51B0 000EDE (v02 CpuRef CpuSsdt 00003000 INTL 20160422) [ 0.014021] ACPI: LPIT 0x00000000651B6090 000094 (v01 INTEL KBL-ULT 00000000 MSFT 0000005F) [ 0.014024] ACPI: WSMT 0x00000000651B6128 000028 (v01 DELL CBX3 00000000 MSFT 0000005F) [ 0.014026] ACPI: SSDT 0x00000000651B6150 000161 (v02 INTEL HdaDsp 00000000 INTL 20160422) [ 0.014029] ACPI: SSDT 0x00000000651B62B8 00029F (v02 INTEL sensrhub 00000000 INTL 20160422) [ 0.014031] ACPI: SSDT 0x00000000651B6558 003002 (v02 INTEL PtidDevc 00001000 INTL 20160422) [ 0.014034] ACPI: SSDT 0x00000000651B9560 0000DB (v02 INTEL TbtTypeC 00000000 INTL 20160422) [ 0.014037] ACPI: DBGP 0x00000000651B9640 000034 (v01 INTEL 00000002 MSFT 0000005F) [ 0.014040] ACPI: DBG2 0x00000000651B9678 000054 (v00 INTEL 00000002 MSFT 0000005F) [ 0.014043] ACPI: SSDT 0x00000000651B96D0 0007DD (v02 INTEL UsbCTabl 00001000 INTL 20160422) [ 0.014046] ACPI: SSDT 0x00000000651B9EB0 0084F1 (v02 DptfTa DptfTabl 00001000 INTL 20160422) [ 0.014049] ACPI: SLIC 0x00000000651C23A8 000176 (v03 DELL CBX3 01072009 MSFT 00010013) [ 0.014051] ACPI: NHLT 0x00000000651C2520 00002D (v00 INTEL EDK2 00000002 01000013) [ 0.014054] ACPI: BGRT 0x00000000651C2550 000038 (v00 01072009 AMI 00010013) [ 0.014056] ACPI: TPM2 0x00000000651C2588 000034 (v03 Tpm2Tabl 00000001 AMI 00000000) [ 0.014059] ACPI: ASF! 0x00000000651C25C0 0000A0 (v32 INTEL HCG 00000001 TFSM 000F4240) [ 0.014061] ACPI: DMAR 0x00000000651C2660 0000F0 (v01 INTEL KBL 00000001 INTL 00000001) [ 0.014063] ACPI: Reserving FACP table memory at [mem 0x651b2a48-0x651b2b53] [ 0.014065] ACPI: Reserving DSDT table memory at [mem 0x6518d260-0x651b2a46] [ 0.014066] ACPI: Reserving FACS table memory at [mem 0x6f86f180-0x6f86f1bf] [ 0.014066] ACPI: Reserving APIC table memory at [mem 0x651b2b58-0x651b2bdb] [ 0.014067] ACPI: Reserving FPDT table memory at [mem 0x651b2be0-0x651b2c23] [ 0.014068] ACPI: Reserving FIDT table memory at [mem 0x651b2c28-0x651b2cd3] [ 0.014068] ACPI: Reserving MCFG table memory at [mem 0x651b2cd8-0x651b2d13] [ 0.014069] ACPI: Reserving HPET table memory at [mem 0x651b2d18-0x651b2d4f] [ 0.014069] ACPI: Reserving SSDT table memory at [mem 0x651b2d50-0x651b30a8] [ 0.014070] ACPI: Reserving BOOT table memory at [mem 0x651b30b0-0x651b30d7] [ 0.014071] ACPI: Reserving SSDT table memory at [mem 0x651b30d8-0x651b43a6] [ 0.014071] ACPI: Reserving HPET table memory at [mem 0x651b43a8-0x651b43df] [ 0.014072] ACPI: Reserving SSDT table memory at [mem 0x651b43e0-0x651b5163] [ 0.014073] ACPI: Reserving UEFI table memory at [mem 0x651b5168-0x651b51a9] [ 0.014073] ACPI: Reserving SSDT table memory at [mem 0x651b51b0-0x651b608d] [ 0.014074] ACPI: Reserving LPIT table memory at [mem 0x651b6090-0x651b6123] [ 0.014075] ACPI: Reserving WSMT table memory at [mem 0x651b6128-0x651b614f] [ 0.014075] ACPI: Reserving SSDT table memory at [mem 0x651b6150-0x651b62b0] [ 0.014076] ACPI: Reserving SSDT table memory at [mem 0x651b62b8-0x651b6556] [ 0.014076] ACPI: Reserving SSDT table memory at [mem 0x651b6558-0x651b9559] [ 0.014077] ACPI: Reserving SSDT table memory at [mem 0x651b9560-0x651b963a] [ 0.014078] ACPI: Reserving DBGP table memory at [mem 0x651b9640-0x651b9673] [ 0.014078] ACPI: Reserving DBG2 table memory at [mem 0x651b9678-0x651b96cb] [ 0.014079] ACPI: Reserving SSDT table memory at [mem 0x651b96d0-0x651b9eac] [ 0.014080] ACPI: Reserving SSDT table memory at [mem 0x651b9eb0-0x651c23a0] [ 0.014080] ACPI: Reserving SLIC table memory at [mem 0x651c23a8-0x651c251d] [ 0.014081] ACPI: Reserving NHLT table memory at [mem 0x651c2520-0x651c254c] [ 0.014081] ACPI: Reserving BGRT table memory at [mem 0x651c2550-0x651c2587] [ 0.014082] ACPI: Reserving TPM2 table memory at [mem 0x651c2588-0x651c25bb] [ 0.014083] ACPI: Reserving ASF! table memory at [mem 0x651c25c0-0x651c265f] [ 0.014083] ACPI: Reserving DMAR table memory at [mem 0x651c2660-0x651c274f] [ 0.014211] No NUMA configuration found [ 0.014212] Faking a node at [mem 0x0000000000000000-0x00000004817fffff] [ 0.014219] NODE_DATA(0) allocated [mem 0x47f3d5000-0x47f3fffff] [ 0.014361] Zone ranges: [ 0.014362] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.014363] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.014365] Normal [mem 0x0000000100000000-0x00000004817fffff] [ 0.014366] Device empty [ 0.014367] Movable zone start for each node [ 0.014369] Early memory node ranges [ 0.014369] node 0: [mem 0x0000000000001000-0x0000000000057fff] [ 0.014370] node 0: [mem 0x0000000000059000-0x000000000009dfff] [ 0.014371] node 0: [mem 0x0000000000100000-0x00000000556aafff] [ 0.014372] node 0: [mem 0x00000000556ad000-0x0000000064df3fff] [ 0.014373] node 0: [mem 0x000000006ffff000-0x000000006fffffff] [ 0.014373] node 0: [mem 0x0000000078000000-0x00000000785fffff] [ 0.014374] node 0: [mem 0x0000000100000000-0x00000004817fffff] [ 0.014376] Initmem setup node 0 [mem 0x0000000000001000-0x00000004817fffff] [ 0.014383] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.014384] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.014406] On node 0, zone DMA: 98 pages in unavailable ranges [ 0.016718] On node 0, zone DMA32: 2 pages in unavailable ranges [ 0.017124] On node 0, zone DMA32: 45579 pages in unavailable ranges [ 0.017624] On node 0, zone Normal: 31232 pages in unavailable ranges [ 0.017854] On node 0, zone Normal: 26624 pages in unavailable ranges [ 0.017862] Reserving Intel graphics memory at [mem 0x7a800000-0x7c7fffff] [ 0.018066] ACPI: PM-Timer IO Port: 0x1808 [ 0.018072] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.018073] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) [ 0.018074] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) [ 0.018074] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1]) [ 0.018101] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119 [ 0.018103] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.018104] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.018109] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.018113] ACPI: HPET id: 0x8086a701 base: 0xfed00000 [ 0.018119] e820: update [mem 0x62260000-0x623ecfff] usable ==> reserved [ 0.018130] TSC deadline timer available [ 0.018131] smpboot: Allowing 4 CPUs, 0 hotplug CPUs [ 0.018145] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.018147] PM: hibernation: Registered nosave memory: [mem 0x00058000-0x00058fff] [ 0.018148] PM: hibernation: Registered nosave memory: [mem 0x0009e000-0x000fffff] [ 0.018149] PM: hibernation: Registered nosave memory: [mem 0x514e7000-0x514e7fff] [ 0.018151] PM: hibernation: Registered nosave memory: [mem 0x514f7000-0x514f7fff] [ 0.018152] PM: hibernation: Registered nosave memory: [mem 0x556ab000-0x556abfff] [ 0.018153] PM: hibernation: Registered nosave memory: [mem 0x556ac000-0x556acfff] [ 0.018154] PM: hibernation: Registered nosave memory: [mem 0x62260000-0x623ecfff] [ 0.018155] PM: hibernation: Registered nosave memory: [mem 0x64df4000-0x6517ffff] [ 0.018156] PM: hibernation: Registered nosave memory: [mem 0x65180000-0x651c3fff] [ 0.018157] PM: hibernation: Registered nosave memory: [mem 0x651c4000-0x6f871fff] [ 0.018157] PM: hibernation: Registered nosave memory: [mem 0x6f872000-0x6fffefff] [ 0.018159] PM: hibernation: Registered nosave memory: [mem 0x70000000-0x77ffffff] [ 0.018160] PM: hibernation: Registered nosave memory: [mem 0x78600000-0x7c7fffff] [ 0.018161] PM: hibernation: Registered nosave memory: [mem 0x7c800000-0xfdffffff] [ 0.018161] PM: hibernation: Registered nosave memory: [mem 0xfe000000-0xfe010fff] [ 0.018162] PM: hibernation: Registered nosave memory: [mem 0xfe011000-0xfebfffff] [ 0.018162] PM: hibernation: Registered nosave memory: [mem 0xfec00000-0xfec00fff] [ 0.018163] PM: hibernation: Registered nosave memory: [mem 0xfec01000-0xfedfffff] [ 0.018163] PM: hibernation: Registered nosave memory: [mem 0xfee00000-0xfee00fff] [ 0.018164] PM: hibernation: Registered nosave memory: [mem 0xfee01000-0xffffffff] [ 0.018165] [mem 0x7c800000-0xfdffffff] available for PCI devices [ 0.018166] Booting paravirtualized kernel on bare hardware [ 0.018168] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns [ 0.022864] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.023145] percpu: Embedded 63 pages/cpu s221184 r8192 d28672 u524288 [ 0.023152] pcpu-alloc: s221184 r8192 d28672 u524288 alloc=1*2097152 [ 0.023154] pcpu-alloc: [0] 0 1 2 3 [ 0.023170] Kernel command line: BOOT_IMAGE=/vmlinuz-6.8.0-rc5+ root=UUID=32e29882-d94d-4a92-9ee4-4d03002bfa29 ro quiet pci=noaer mem_sleep_default=deep log_buf_len=8M cryptomgr.notests usbcore.dyndbg=+p [ 0.023257] Unknown kernel command line parameters "BOOT_IMAGE=/vmlinuz-6.8.0-rc5+", will be passed to user space. [ 0.023290] random: crng init done [ 0.024781] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.025540] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.025601] Fallback order for Node 0: 0 [ 0.025604] Built 1 zonelists, mobility grouping on. Total pages: 4026691 [ 0.025605] Policy zone: Normal [ 0.025609] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.025616] software IO TLB: area num 4. [ 0.043632] Memory: 1657864K/16363068K available (16384K kernel code, 2331K rwdata, 5868K rodata, 3976K init, 3680K bss, 493948K reserved, 0K cma-reserved) [ 0.043813] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.043822] Kernel/User page tables isolation: enabled [ 0.043844] ftrace: allocating 42500 entries in 167 pages [ 0.050911] ftrace: allocated 167 pages with 5 groups [ 0.051533] Dynamic Preempt: voluntary [ 0.051559] rcu: Preemptible hierarchical RCU implementation. [ 0.051560] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4. [ 0.051561] Trampoline variant of Tasks RCU enabled. [ 0.051561] Rude variant of Tasks RCU enabled. [ 0.051562] Tracing variant of Tasks RCU enabled. [ 0.051562] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.051563] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.054100] NR_IRQS: 524544, nr_irqs: 1024, preallocated irqs: 16 [ 0.054303] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.054462] Console: colour dummy device 80x25 [ 0.054464] printk: legacy console [tty0] enabled [ 0.054499] ACPI: Core revision 20230628 [ 0.054647] hpet: HPET dysfunctional in PC10. Force disabled. [ 0.054648] APIC: Switch to symmetric I/O mode setup [ 0.054650] DMAR: Host address width 39 [ 0.054650] DMAR: DRHD base: 0x000000fed90000 flags: 0x0 [ 0.054656] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap 1c0000c40660462 ecap 19e2ff0505e [ 0.054658] DMAR: DRHD base: 0x000000fed91000 flags: 0x1 [ 0.054661] DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008c40660462 ecap f050da [ 0.054663] DMAR: RMRR base: 0x00000064ec2000 end: 0x00000064ee1fff [ 0.054664] DMAR: RMRR base: 0x0000007a000000 end: 0x0000007c7fffff [ 0.054665] DMAR: ANDD device: 1 name: \_SB.PCI0.I2C0 [ 0.054666] DMAR: ANDD device: 2 name: \_SB.PCI0.I2C1 [ 0.054667] DMAR-IR: IOAPIC id 2 under DRHD base 0xfed91000 IOMMU 1 [ 0.054669] DMAR-IR: HPET id 0 under DRHD base 0xfed91000 [ 0.054669] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping. [ 0.056297] DMAR-IR: Enabled IRQ remapping in x2apic mode [ 0.056298] x2apic enabled [ 0.056355] APIC: Switched APIC routing to: cluster x2apic [ 0.060202] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x29ccd767b87, max_idle_ns: 440795223720 ns [ 0.060208] Calibrating delay loop (skipped), value calculated using timer frequency.. 5799.77 BogoMIPS (lpj=11599544) [ 0.060245] CPU0: Thermal monitoring enabled (TM1) [ 0.060279] process: using mwait in idle threads [ 0.060281] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8 [ 0.060282] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4 [ 0.060286] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.060288] Spectre V2 : Mitigation: IBRS [ 0.060289] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.060289] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.060290] RETBleed: Mitigation: IBRS [ 0.060292] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.060293] Spectre V2 : User space: Mitigation: STIBP via prctl [ 0.060294] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl [ 0.060302] MDS: Mitigation: Clear CPU buffers [ 0.060302] MMIO Stale Data: Mitigation: Clear CPU buffers [ 0.060306] SRBDS: Mitigation: Microcode [ 0.060312] GDS: Mitigation: Microcode [ 0.060318] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.060320] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.060321] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.060321] x86/fpu: Supporting XSAVE feature 0x008: 'MPX bounds registers' [ 0.060322] x86/fpu: Supporting XSAVE feature 0x010: 'MPX CSR' [ 0.060324] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.060325] x86/fpu: xstate_offset[3]: 832, xstate_sizes[3]: 64 [ 0.060327] x86/fpu: xstate_offset[4]: 896, xstate_sizes[4]: 64 [ 0.060328] x86/fpu: Enabled xstate features 0x1f, context size is 960 bytes, using 'compacted' format. [ 0.064205] Freeing SMP alternatives memory: 36K [ 0.064205] pid_max: default: 32768 minimum: 301 [ 0.064205] LSM: initializing lsm=lockdown,capability,landlock,yama,apparmor,tomoyo,bpf,integrity [ 0.064205] landlock: Up and running. [ 0.064205] Yama: becoming mindful. [ 0.064205] AppArmor: AppArmor initialized [ 0.064205] TOMOYO Linux initialized [ 0.064205] LSM support for eBPF active [ 0.064205] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.064205] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.064205] smpboot: CPU0: Intel(R) Core(TM) i7-7500U CPU @ 2.70GHz (family: 0x6, model: 0x8e, stepping: 0x9) [ 0.064205] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.064205] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.064205] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.064205] Performance Events: PEBS fmt3+, Skylake events, 32-deep LBR, full-width counters, Intel PMU driver. [ 0.064205] ... version: 4 [ 0.064205] ... bit width: 48 [ 0.064205] ... generic registers: 4 [ 0.064205] ... value mask: 0000ffffffffffff [ 0.064205] ... max period: 00007fffffffffff [ 0.064205] ... fixed-purpose events: 3 [ 0.064205] ... event mask: 000000070000000f [ 0.064205] signal: max sigframe size: 2032 [ 0.064205] Estimated ratio of average max frequency by base frequency (times 1024): 1235 [ 0.064205] rcu: Hierarchical SRCU implementation. [ 0.064205] rcu: Max phase no-delay instances is 1000. [ 0.064205] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter. [ 0.064205] smp: Bringing up secondary CPUs ... [ 0.064205] smpboot: x86: Booting SMP configuration: [ 0.064205] .... node #0, CPUs: #1 #2 #3 [ 0.064205] MDS CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/mds.html for more details. [ 0.064205] MMIO Stale Data CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/processor_mmio_stale_data.html for more details. [ 0.064205] smp: Brought up 1 node, 4 CPUs [ 0.064205] smpboot: Max logical packages: 1 [ 0.064205] smpboot: Total of 4 processors activated (23199.08 BogoMIPS) [ 0.085219] node 0 deferred pages initialised in 20ms [ 0.085220] devtmpfs: initialized [ 0.085220] x86/mm: Memory block size: 128MB [ 0.085582] ACPI: PM: Registering ACPI NVS region [mem 0x556ab000-0x556abfff] (4096 bytes) [ 0.085582] ACPI: PM: Registering ACPI NVS region [mem 0x651c4000-0x6f871fff] (174776320 bytes) [ 0.089271] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.089287] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.089336] pinctrl core: initialized pinctrl subsystem [ 0.089812] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.090047] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.090165] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.090277] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.090302] audit: initializing netlink subsys (disabled) [ 0.090318] audit: type=2000 audit(1708510974.028:1): state=initialized audit_enabled=0 res=1 [ 0.090318] thermal_sys: Registered thermal governor 'fair_share' [ 0.090318] thermal_sys: Registered thermal governor 'bang_bang' [ 0.090318] thermal_sys: Registered thermal governor 'step_wise' [ 0.090318] thermal_sys: Registered thermal governor 'user_space' [ 0.090318] thermal_sys: Registered thermal governor 'power_allocator' [ 0.090318] cpuidle: using governor ladder [ 0.090318] cpuidle: using governor menu [ 0.090318] Simple Boot Flag at 0x47 set to 0x80 [ 0.090318] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.090318] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.090318] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff] [ 0.090318] PCI: not using ECAM ([mem 0xe0000000-0xefffffff] not reserved) [ 0.090318] PCI: Using configuration type 1 for base access [ 0.090318] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.090318] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.090318] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page [ 0.090318] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.090318] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page [ 0.090318] ACPI: Added _OSI(Module Device) [ 0.090318] ACPI: Added _OSI(Processor Device) [ 0.090318] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.090318] ACPI: Added _OSI(Processor Aggregator Device) [ 0.132321] ACPI: 11 ACPI AML tables successfully acquired and loaded [ 0.136256] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored [ 0.141441] ACPI: Dynamic OEM Table Load: [ 0.141441] ACPI: SSDT 0xFFFF8ABE6F0C3800 0003FF (v02 PmRef Cpu0Cst 00003001 INTL 20160422) [ 0.142413] ACPI: Dynamic OEM Table Load: [ 0.142418] ACPI: SSDT 0xFFFF8ABC0790F000 0006F6 (v02 PmRef Cpu0Ist 00003000 INTL 20160422) [ 0.145825] ACPI: Dynamic OEM Table Load: [ 0.145830] ACPI: SSDT 0xFFFF8ABC0790B800 00065C (v02 PmRef ApIst 00003000 INTL 20160422) [ 0.147488] ACPI: Dynamic OEM Table Load: [ 0.147492] ACPI: SSDT 0xFFFF8ABB00E38800 00018A (v02 PmRef ApCst 00003000 INTL 20160422) [ 0.150543] ACPI: _OSC evaluated successfully for all CPUs [ 0.150726] ACPI: EC: EC started [ 0.150727] ACPI: EC: interrupt blocked [ 0.157117] ACPI: EC: EC_CMD/EC_SC=0x934, EC_DATA=0x930 [ 0.157119] ACPI: \_SB_.PCI0.LPCB.ECDV: Boot DSDT EC used to handle transactions [ 0.157121] ACPI: Interpreter enabled [ 0.157161] ACPI: PM: (supports S0 S3 S4 S5) [ 0.157162] ACPI: Using IOAPIC for interrupt routing [ 0.157197] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff] [ 0.158121] PCI: ECAM [mem 0xe0000000-0xefffffff] reserved as ACPI motherboard resource [ 0.158130] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.158132] PCI: Using E820 reservations for host bridge windows [ 0.158778] ACPI: Enabled 8 GPEs in block 00 to 7F [ 0.164597] ACPI: \_SB_.PCI0.RP09.PXSX.WRST: New power resource [ 0.164922] ACPI: \_SB_.PCI0.RP10.PXSX.WRST: New power resource [ 0.165247] ACPI: \_SB_.PCI0.RP11.PXSX.WRST: New power resource [ 0.165573] ACPI: \_SB_.PCI0.RP12.PXSX.WRST: New power resource [ 0.165894] ACPI: \_SB_.PCI0.RP13.PXSX.WRST: New power resource [ 0.166219] ACPI: \_SB_.PCI0.RP01.PXSX.WRST: New power resource [ 0.167043] ACPI: \_SB_.PCI0.RP02.PXSX.WRST: New power resource [ 0.167365] ACPI: \_SB_.PCI0.RP03.PXSX.WRST: New power resource [ 0.167687] ACPI: \_SB_.PCI0.RP04.PXSX.WRST: New power resource [ 0.168009] ACPI: \_SB_.PCI0.RP05.PXSX.WRST: New power resource [ 0.168339] ACPI: \_SB_.PCI0.RP06.PXSX.WRST: New power resource [ 0.168661] ACPI: \_SB_.PCI0.RP07.PXSX.WRST: New power resource [ 0.168985] ACPI: \_SB_.PCI0.RP08.PXSX.WRST: New power resource [ 0.169315] ACPI: \_SB_.PCI0.RP17.PXSX.WRST: New power resource [ 0.169640] ACPI: \_SB_.PCI0.RP18.PXSX.WRST: New power resource [ 0.169961] ACPI: \_SB_.PCI0.RP19.PXSX.WRST: New power resource [ 0.170285] ACPI: \_SB_.PCI0.RP20.PXSX.WRST: New power resource [ 0.172206] ACPI: \_SB_.PCI0.RP14.PXSX.WRST: New power resource [ 0.172206] ACPI: \_SB_.PCI0.RP15.PXSX.WRST: New power resource [ 0.172302] ACPI: \_SB_.PCI0.RP16.PXSX.WRST: New power resource [ 0.195900] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe]) [ 0.195906] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.196105] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug SHPCHotplug PME] [ 0.196489] acpi PNP0A08:00: _OSC: OS now controls [PCIeCapability LTR] [ 0.196491] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration [ 0.197446] PCI host bridge to bus 0000:00 [ 0.197448] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.197450] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.197452] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000dffff window] [ 0.197453] pci_bus 0000:00: root bus resource [mem 0x7c800000-0xdfffffff window] [ 0.197455] pci_bus 0000:00: root bus resource [mem 0xfd000000-0xfe7fffff window] [ 0.197456] pci_bus 0000:00: root bus resource [bus 00-fe] [ 0.197473] pci 0000:00:00.0: [8086:5904] type 00 class 0x060000 conventional PCI endpoint [ 0.197540] pci 0000:00:02.0: [8086:5916] type 00 class 0x030000 PCIe Root Complex Integrated Endpoint [ 0.197547] pci 0000:00:02.0: BAR 0 [mem 0xdb000000-0xdbffffff 64bit] [ 0.197552] pci 0000:00:02.0: BAR 2 [mem 0x90000000-0x9fffffff 64bit pref] [ 0.197555] pci 0000:00:02.0: BAR 4 [io 0xf000-0xf03f] [ 0.197570] pci 0000:00:02.0: BAR 2: assigned to efifb [ 0.197573] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.197729] pci 0000:00:04.0: [8086:1903] type 00 class 0x118000 conventional PCI endpoint [ 0.197737] pci 0000:00:04.0: BAR 0 [mem 0xdc320000-0xdc327fff 64bit] [ 0.198016] pci 0000:00:14.0: [8086:9d2f] type 00 class 0x0c0330 conventional PCI endpoint [ 0.198033] pci 0000:00:14.0: BAR 0 [mem 0xdc310000-0xdc31ffff 64bit] [ 0.198092] pci 0000:00:14.0: PME# supported from D3hot D3cold [ 0.198644] pci 0000:00:14.2: [8086:9d31] type 00 class 0x118000 conventional PCI endpoint [ 0.198659] pci 0000:00:14.2: BAR 0 [mem 0xdc334000-0xdc334fff 64bit] [ 0.198800] pci 0000:00:15.0: [8086:9d60] type 00 class 0x118000 conventional PCI endpoint [ 0.198843] pci 0000:00:15.0: BAR 0 [mem 0xdc333000-0xdc333fff 64bit] [ 0.199212] pci 0000:00:15.1: [8086:9d61] type 00 class 0x118000 conventional PCI endpoint [ 0.199242] pci 0000:00:15.1: BAR 0 [mem 0xdc332000-0xdc332fff 64bit] [ 0.199602] pci 0000:00:16.0: [8086:9d3a] type 00 class 0x078000 conventional PCI endpoint [ 0.199616] pci 0000:00:16.0: BAR 0 [mem 0xdc331000-0xdc331fff 64bit] [ 0.199660] pci 0000:00:16.0: PME# supported from D3hot [ 0.200000] pci 0000:00:1c.0: [8086:9d10] type 01 class 0x060400 PCIe Root Port [ 0.200019] pci 0000:00:1c.0: PCI bridge to [bus 01-39] [ 0.200024] pci 0000:00:1c.0: bridge window [mem 0xc4000000-0xda0fffff] [ 0.200032] pci 0000:00:1c.0: bridge window [mem 0xa0000000-0xc1ffffff 64bit pref] [ 0.200049] pci 0000:00:1c.0: broken device, retraining non-functional downstream link at 2.5GT/s [ 1.208224] pci 0000:00:1c.0: retraining failed [ 1.208354] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 1.208866] pci 0000:00:1c.4: [8086:9d14] type 01 class 0x060400 PCIe Root Port [ 1.208889] pci 0000:00:1c.4: PCI bridge to [bus 3a] [ 1.208894] pci 0000:00:1c.4: bridge window [mem 0xdc000000-0xdc1fffff] [ 1.208952] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 1.209461] pci 0000:00:1d.0: [8086:9d18] type 01 class 0x060400 PCIe Root Port [ 1.209480] pci 0000:00:1d.0: PCI bridge to [bus 3b] [ 1.209485] pci 0000:00:1d.0: bridge window [mem 0xdc200000-0xdc2fffff] [ 1.209535] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold [ 1.210049] pci 0000:00:1f.0: [8086:9d58] type 00 class 0x060100 conventional PCI endpoint [ 1.210368] pci 0000:00:1f.2: [8086:9d21] type 00 class 0x058000 conventional PCI endpoint [ 1.210380] pci 0000:00:1f.2: BAR 0 [mem 0xdc32c000-0xdc32ffff] [ 1.210621] pci 0000:00:1f.3: [8086:9d71] type 00 class 0x040380 conventional PCI endpoint [ 1.210640] pci 0000:00:1f.3: BAR 0 [mem 0xdc328000-0xdc32bfff 64bit] [ 1.210664] pci 0000:00:1f.3: BAR 4 [mem 0xdc300000-0xdc30ffff 64bit] [ 1.210707] pci 0000:00:1f.3: PME# supported from D3hot D3cold [ 1.211321] pci 0000:00:1f.4: [8086:9d23] type 00 class 0x0c0500 conventional PCI endpoint [ 1.211379] pci 0000:00:1f.4: BAR 0 [mem 0xdc330000-0xdc3300ff 64bit] [ 1.211450] pci 0000:00:1f.4: BAR 4 [io 0xf040-0xf05f] [ 1.211788] pci 0000:00:1c.0: PCI bridge to [bus 01-39] [ 1.212123] pci 0000:3a:00.0: [168c:003e] type 00 class 0x028000 PCIe Endpoint [ 1.212423] pci 0000:3a:00.0: BAR 0 [mem 0xdc000000-0xdc1fffff 64bit] [ 1.213522] pci 0000:3a:00.0: PME# supported from D0 D3hot D3cold [ 1.215186] pci 0000:00:1c.4: PCI bridge to [bus 3a] [ 1.215276] pci 0000:3b:00.0: [1c5c:1284] type 00 class 0x010802 PCIe Endpoint [ 1.215296] pci 0000:3b:00.0: BAR 0 [mem 0xdc200000-0xdc203fff 64bit] [ 1.215405] pci 0000:3b:00.0: PME# supported from D0 D1 D3hot [ 1.215787] pci 0000:00:1d.0: PCI bridge to [bus 3b] [ 1.218778] ACPI: PCI: Interrupt link LNKA configured for IRQ 11 [ 1.218778] ACPI: PCI: Interrupt link LNKB configured for IRQ 10 [ 1.218778] ACPI: PCI: Interrupt link LNKC configured for IRQ 11 [ 1.218778] ACPI: PCI: Interrupt link LNKD configured for IRQ 11 [ 1.218778] ACPI: PCI: Interrupt link LNKE configured for IRQ 11 [ 1.218778] ACPI: PCI: Interrupt link LNKF configured for IRQ 11 [ 1.218778] ACPI: PCI: Interrupt link LNKG configured for IRQ 11 [ 1.218778] ACPI: PCI: Interrupt link LNKH configured for IRQ 11 [ 1.232239] ACPI: EC: interrupt unblocked [ 1.232241] ACPI: EC: event unblocked [ 1.232246] ACPI: EC: EC_CMD/EC_SC=0x934, EC_DATA=0x930 [ 1.232247] ACPI: EC: GPE=0x14 [ 1.232249] ACPI: \_SB_.PCI0.LPCB.ECDV: Boot DSDT EC initialization complete [ 1.232250] ACPI: \_SB_.PCI0.LPCB.ECDV: EC: Used to handle transactions and events [ 1.232325] iommu: Default domain type: Translated [ 1.232325] iommu: DMA domain TLB invalidation policy: lazy mode [ 1.232342] pps_core: LinuxPPS API ver. 1 registered [ 1.232343] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.232346] PTP clock support registered [ 1.232355] EDAC MC: Ver: 3.0.0 [ 1.232598] efivars: Registered efivars operations [ 1.232598] NetLabel: Initializing [ 1.232598] NetLabel: domain hash size = 128 [ 1.232598] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 1.232598] NetLabel: unlabeled traffic allowed by default [ 1.232598] PCI: Using ACPI for IRQ routing [ 1.258585] PCI: pci_cache_line_size set to 64 bytes [ 1.258961] e820: reserve RAM buffer [mem 0x00058000-0x0005ffff] [ 1.258962] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff] [ 1.258963] e820: reserve RAM buffer [mem 0x514e7018-0x53ffffff] [ 1.258965] e820: reserve RAM buffer [mem 0x556ab000-0x57ffffff] [ 1.258966] e820: reserve RAM buffer [mem 0x62260000-0x63ffffff] [ 1.258967] e820: reserve RAM buffer [mem 0x64df4000-0x67ffffff] [ 1.258968] e820: reserve RAM buffer [mem 0x78600000-0x7bffffff] [ 1.258968] e820: reserve RAM buffer [mem 0x481800000-0x483ffffff] [ 1.259005] pci 0000:00:02.0: vgaarb: setting as boot VGA device [ 1.259005] pci 0000:00:02.0: vgaarb: bridge control possible [ 1.259005] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 1.259005] vgaarb: loaded [ 1.259005] clocksource: Switched to clocksource tsc-early [ 1.259005] VFS: Disk quotas dquot_6.6.0 [ 1.259005] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.259005] AppArmor: AppArmor Filesystem Enabled [ 1.259005] pnp: PnP ACPI init [ 1.259005] system 00:00: [io 0x0680-0x069f] has been reserved [ 1.259005] system 00:00: [io 0xffff] has been reserved [ 1.259005] system 00:00: [io 0xffff] has been reserved [ 1.259005] system 00:00: [io 0xffff] has been reserved [ 1.259005] system 00:00: [io 0x1800-0x18fe] has been reserved [ 1.259005] system 00:00: [io 0x164e-0x164f] has been reserved [ 1.259005] system 00:02: [io 0x1854-0x1857] has been reserved [ 1.259005] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved [ 1.259005] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved [ 1.259005] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved [ 1.259005] system 00:05: [mem 0xe0000000-0xefffffff] has been reserved [ 1.259005] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved [ 1.259005] system 00:05: [mem 0xfed90000-0xfed93fff] could not be reserved [ 1.259005] system 00:05: [mem 0xfed45000-0xfed8ffff] has been reserved [ 1.259005] system 00:05: [mem 0xff000000-0xffffffff] has been reserved [ 1.259005] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved [ 1.259005] system 00:05: [mem 0xdffe0000-0xdfffffff] has been reserved [ 1.259005] system 00:06: [mem 0xfd000000-0xfdabffff] has been reserved [ 1.259005] system 00:06: [mem 0xfdad0000-0xfdadffff] has been reserved [ 1.259005] system 00:06: [mem 0xfdb00000-0xfdffffff] has been reserved [ 1.259005] system 00:06: [mem 0xfe000000-0xfe01ffff] could not be reserved [ 1.259005] system 00:06: [mem 0xfe036000-0xfe03bfff] has been reserved [ 1.259005] system 00:06: [mem 0xfe03d000-0xfe3fffff] has been reserved [ 1.259005] system 00:06: [mem 0xfe410000-0xfe7fffff] has been reserved [ 1.259005] system 00:07: [io 0xff00-0xfffe] has been reserved [ 1.259240] system 00:08: [mem 0xfe029000-0xfe029fff] has been reserved [ 1.259242] system 00:08: [mem 0xfe028000-0xfe028fff] has been reserved [ 1.263420] pnp: PnP ACPI: found 9 devices [ 1.268927] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 1.268969] pci 0000:00:1f.1: [8086:9d20] type 00 class 0x058000 conventional PCI endpoint [ 1.269028] pci 0000:00:1f.1: BAR 0 [mem 0xfd000000-0xfdffffff 64bit] [ 1.269294] NET: Registered PF_INET protocol family [ 1.269412] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 1.271705] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 1.271727] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.271776] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 1.271951] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) [ 1.272139] TCP: Hash tables configured (established 131072 bind 65536) [ 1.272213] MPTCP token hash table entries: 16384 (order: 6, 393216 bytes, linear) [ 1.272254] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 1.272285] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 1.272346] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.272353] NET: Registered PF_XDP protocol family [ 1.272360] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01-39] add_size 1000 [ 1.272370] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]: assigned [ 1.272374] pci 0000:00:1c.0: PCI bridge to [bus 01-39] [ 1.272376] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff] [ 1.272380] pci 0000:00:1c.0: bridge window [mem 0xc4000000-0xda0fffff] [ 1.272382] pci 0000:00:1c.0: bridge window [mem 0xa0000000-0xc1ffffff 64bit pref] [ 1.272387] pci 0000:00:1c.4: PCI bridge to [bus 3a] [ 1.272390] pci 0000:00:1c.4: bridge window [mem 0xdc000000-0xdc1fffff] [ 1.272396] pci 0000:00:1d.0: PCI bridge to [bus 3b] [ 1.272399] pci 0000:00:1d.0: bridge window [mem 0xdc200000-0xdc2fffff] [ 1.272404] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 1.272405] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 1.272407] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000dffff window] [ 1.272408] pci_bus 0000:00: resource 7 [mem 0x7c800000-0xdfffffff window] [ 1.272409] pci_bus 0000:00: resource 8 [mem 0xfd000000-0xfe7fffff window] [ 1.272410] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff] [ 1.272412] pci_bus 0000:01: resource 1 [mem 0xc4000000-0xda0fffff] [ 1.272413] pci_bus 0000:01: resource 2 [mem 0xa0000000-0xc1ffffff 64bit pref] [ 1.272414] pci_bus 0000:3a: resource 1 [mem 0xdc000000-0xdc1fffff] [ 1.272415] pci_bus 0000:3b: resource 1 [mem 0xdc200000-0xdc2fffff] [ 1.273061] PCI: CLS 0 bytes, default 64 [ 1.273071] DMAR: ACPI device "device:79" under DMAR at fed91000 as 00:15.0 [ 1.273075] DMAR: ACPI device "device:7a" under DMAR at fed91000 as 00:15.1 [ 1.273084] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.273085] software IO TLB: mapped [mem 0x000000005e260000-0x0000000062260000] (64MB) [ 1.273113] Unpacking initramfs... [ 1.273146] sgx: EPC section 0x70200000-0x75f7ffff [ 1.274487] Initialise system trusted keyrings [ 1.274511] Key type blacklist registered [ 1.274578] workingset: timestamp_bits=36 max_order=22 bucket_order=0 [ 1.274591] zbud: loaded [ 1.274732] fuse: init (API version 7.39) [ 1.274875] integrity: Platform Keyring initialized [ 1.274878] integrity: Machine keyring initialized [ 1.274879] Key type asymmetric registered [ 1.274880] Asymmetric key parser 'x509' registered [ 1.302106] Freeing initrd memory: 18876K [ 1.305552] alg: self-tests disabled [ 1.305614] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.305639] io scheduler mq-deadline registered [ 1.306679] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 1.308820] thermal LNXTHERM:00: registered as thermal_zone0 [ 1.308822] ACPI: thermal: Thermal Zone [THM] (25 C) [ 1.308947] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.309407] hpet_acpi_add: no address or irqs in _CRS [ 1.321602] tpm_tis MSFT0101:00: 2.0 TPM (device-id 0xFE, rev-id 4) [ 1.362384] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 1.362721] i8042: Warning: Keylock active [ 1.364933] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.364938] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.365033] mousedev: PS/2 mouse device common for all mice [ 1.365047] rtc_cmos 00:01: RTC can wake from S4 [ 1.365753] rtc_cmos 00:01: registered as rtc0 [ 1.365914] rtc_cmos 00:01: setting system clock to 2024-02-21T10:22:56 UTC (1708510976) [ 1.365939] rtc_cmos 00:01: alarms up to one month, y3k, 242 bytes nvram [ 1.366158] intel_pstate: Intel P-state driver initializing [ 1.366333] intel_pstate: HWP enabled [ 1.366353] ledtrig-cpu: registered to indicate activity on CPUs [ 1.366628] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 1.366645] efifb: probing for efifb [ 1.366656] efifb: framebuffer at 0x90000000, using 22500k, total 22500k [ 1.366658] efifb: mode is 3200x1800x32, linelength=12800, pages=1 [ 1.366659] efifb: scrolling: redraw [ 1.366660] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0 [ 1.366740] Console: switching to colour frame buffer device 200x56 [ 1.370305] fb0: EFI VGA frame buffer device [ 1.370465] NET: Registered PF_INET6 protocol family [ 1.374490] Segment Routing with IPv6 [ 1.374502] In-situ OAM (IOAM) with IPv6 [ 1.374533] mip6: Mobile IPv6 [ 1.374537] NET: Registered PF_PACKET protocol family [ 1.374594] mpls_gso: MPLS GSO support [ 1.374789] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' [ 1.374818] microcode: Current revision: 0x000000f4 [ 1.374820] microcode: Updated early from: 0x000000f0 [ 1.374878] IPI shorthand broadcast: enabled [ 1.375915] sched_clock: Marking stable (1369090320, 5776069)->(1411061920, -36195531) [ 1.376060] registered taskstats version 1 [ 1.376086] Loading compiled-in X.509 certificates [ 1.376674] Loaded X.509 cert 'Build time autogenerated kernel key: d47c33c70b7d8c925a93309ef39ed6f8acab6016' [ 1.378155] Key type .fscrypt registered [ 1.378156] Key type fscrypt-provisioning registered [ 1.382762] cryptd: module verification failed: signature and/or required key missing - tainting kernel [ 1.383264] cryptd: max_cpu_qlen set to 1000 [ 1.384241] AVX2 version of gcm_enc/dec engaged. [ 1.384273] AES CTR mode by8 optimization enabled [ 1.396263] Key type encrypted registered [ 1.396268] AppArmor: AppArmor sha256 policy hashing enabled [ 1.396532] integrity: Loading X.509 certificate: UEFI:db [ 1.396553] integrity: Loaded X.509 cert 'Dell Inc. UEFI DB: 5ddb772dc880660055ba0bc131886bb630a639e7' [ 1.396554] integrity: Loading X.509 certificate: UEFI:db [ 1.396573] integrity: Loaded X.509 cert 'Microsoft Corporation UEFI CA 2011: 13adbf4309bd82709c8cd54f316ed522988a1bd4' [ 1.396574] integrity: Loading X.509 certificate: UEFI:db [ 1.396589] integrity: Loaded X.509 cert 'Microsoft Windows Production PCA 2011: a92902398e16c49778cd90f99e4f9ae17c55af53' [ 1.396931] ima: Allocated hash algorithm: sha256 [ 1.433743] ima: No architecture policies found [ 1.433772] evm: Initialising EVM extended attributes: [ 1.433773] evm: security.selinux [ 1.433774] evm: security.SMACK64 (disabled) [ 1.433776] evm: security.SMACK64EXEC (disabled) [ 1.433784] evm: security.SMACK64TRANSMUTE (disabled) [ 1.433786] evm: security.SMACK64MMAP (disabled) [ 1.433787] evm: security.apparmor [ 1.433788] evm: security.ima [ 1.433789] evm: security.capability [ 1.433791] evm: HMAC attrs: 0x1 [ 1.434881] RAS: Correctable Errors collector initialized. [ 1.434923] clk: Disabling unused clocks [ 1.435966] Freeing unused decrypted memory: 2036K [ 1.436485] Freeing unused kernel image (initmem) memory: 3976K [ 1.457998] Write protecting the kernel read-only data: 22528k [ 1.458973] Freeing unused kernel image (rodata/data gap) memory: 276K [ 1.533218] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 1.533219] x86/mm: Checking user space page tables [ 1.575719] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 1.575731] Run /init as init process [ 1.575732] with arguments: [ 1.575733] /init [ 1.575734] with environment: [ 1.575735] HOME=/ [ 1.575735] TERM=linux [ 1.575736] BOOT_IMAGE=/vmlinuz-6.8.0-rc5+ [ 1.756585] hid: raw HID events driver (C) Jiri Kosina [ 1.773848] ACPI: bus type USB registered [ 1.773895] usbcore: registered new interface driver usbfs [ 1.773906] usbcore: registered new interface driver hub [ 1.773919] usbcore: registered new device driver usb [ 1.795149] ACPI: bus type drm_connector registered [ 1.795369] i801_smbus 0000:00:1f.4: SPD Write Disable is set [ 1.795409] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt [ 1.805050] i2c i2c-0: 2/2 memory slots populated (from DMI) [ 1.806820] intel-lpss 0000:00:15.0: enabling device (0000 -> 0002) [ 1.807071] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 1.807086] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1 [ 1.807228] idma64 idma64.0: Found Intel integrated DMA 64-bit [ 1.808155] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000081109810 [ 1.808618] xhci_hcd 0000:00:14.0: supports USB remote wakeup [ 1.809330] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 1.809336] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2 [ 1.809340] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed [ 1.809343] xhci_hcd 0000:00:14.0: supports USB remote wakeup [ 1.809371] usb usb1: default language 0x0409 [ 1.809389] usb usb1: udev 1, busnum 1, minor = 0 [ 1.809392] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.08 [ 1.809395] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.809398] usb usb1: Product: xHCI Host Controller [ 1.809399] usb usb1: Manufacturer: Linux 6.8.0-rc5+ xhci-hcd [ 1.809400] usb usb1: SerialNumber: 0000:00:14.0 [ 1.809553] usb usb1: usb_probe_device [ 1.809555] usb usb1: configuration #1 chosen from 1 choice [ 1.809565] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 1.809664] hub 1-0:1.0: usb_probe_interface [ 1.809667] hub 1-0:1.0: usb_probe_interface - got id [ 1.809669] hub 1-0:1.0: USB hub found [ 1.809984] hub 1-0:1.0: 12 ports detected [ 1.809987] hub 1-0:1.0: standalone hub [ 1.809989] hub 1-0:1.0: no power switching (usb 1.0) [ 1.809990] hub 1-0:1.0: individual port over-current protection [ 1.809992] hub 1-0:1.0: Single TT [ 1.809993] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 1.809995] hub 1-0:1.0: power on to power good time: 20ms [ 1.810005] hub 1-0:1.0: local power source is good [ 1.812755] usb usb1-port3: DeviceRemovable is changed to 1 according to platform information. [ 1.812759] usb usb1-port4: DeviceRemovable is changed to 1 according to platform information. [ 1.812760] usb usb1-port5: DeviceRemovable is changed to 1 according to platform information. [ 1.812762] hub 1-0:1.0: trying to enable port power on non-switchable hub [ 1.813851] usb usb2: skipped 1 descriptor after endpoint [ 1.813857] usb usb2: default language 0x0409 [ 1.813870] usb usb2: udev 1, busnum 2, minor = 128 [ 1.813873] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.08 [ 1.813875] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.813877] usb usb2: Product: xHCI Host Controller [ 1.813879] usb usb2: Manufacturer: Linux 6.8.0-rc5+ xhci-hcd [ 1.813881] usb usb2: SerialNumber: 0000:00:14.0 [ 1.814040] usb usb2: usb_probe_device [ 1.814042] usb usb2: configuration #1 chosen from 1 choice [ 1.814056] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 1.814123] hub 2-0:1.0: usb_probe_interface [ 1.814125] hub 2-0:1.0: usb_probe_interface - got id [ 1.814127] hub 2-0:1.0: USB hub found [ 1.814139] hub 2-0:1.0: 6 ports detected [ 1.814141] hub 2-0:1.0: standalone hub [ 1.814142] hub 2-0:1.0: no power switching (usb 1.0) [ 1.814143] hub 2-0:1.0: individual port over-current protection [ 1.814145] hub 2-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 1.814146] hub 2-0:1.0: power on to power good time: 100ms [ 1.814153] hub 2-0:1.0: local power source is good [ 1.814576] usb usb2-port1: peered to usb1-port1 [ 1.814885] usb usb2-port2: peered to usb1-port2 [ 1.816270] usb usb2: port-1 no _DSM function 5 [ 1.816294] usb usb2: port-2 no _DSM function 5 [ 1.816544] usb usb2: port-3 no _DSM function 5 [ 1.816576] usb usb2: port-4 no _DSM function 5 [ 1.816581] usb usb2: port-5 no _DSM function 5 [ 1.816601] usb usb2: port-6 no _DSM function 5 [ 1.816604] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 1.817182] nvme nvme0: pci function 0000:3b:00.0 [ 1.823024] intel-lpss 0000:00:15.1: enabling device (0000 -> 0002) [ 1.823235] idma64 idma64.1: Found Intel integrated DMA 64-bit [ 1.833912] usb usb1-port1: status 0301 change 0001 [ 1.833927] usb usb1-port2: status 0301 change 0001 [ 1.833939] usb usb1-port3: status 0101 change 0001 [ 1.833948] usb usb1-port4: status 0101 change 0001 [ 1.833957] usb usb1-port5: status 0101 change 0001 [ 1.833976] nvme nvme0: 4/0/0 default/read/poll queues [ 1.839288] nvme0n1: p1 p2 p3 p4 [ 1.937912] hub 1-0:1.0: state 7 ports 12 chg 003e evt 0000 [ 1.937959] usb usb1-port1: status 0301, change 0000, 1.5 Mb/s [ 2.000688] input: DLL075B:01 06CB:76AF Mouse as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-2/i2c-DLL075B:01/0018:06CB:76AF.0001/input/input2 [ 2.001083] input: DLL075B:01 06CB:76AF Touchpad as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-2/i2c-DLL075B:01/0018:06CB:76AF.0001/input/input3 [ 2.001430] hid-generic 0018:06CB:76AF.0001: input,hidraw0: I2C HID v1.00 Mouse [DLL075B:01 06CB:76AF] on i2c-DLL075B:01 [ 2.025876] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 2.029449] hub 2-0:1.0: hub_suspend [ 2.029484] usb usb2: bus auto-suspend, wakeup 1 [ 2.029517] usb usb2: suspend raced with wakeup event [ 2.029526] usb usb2: usb auto-resume [ 2.041886] hub 2-0:1.0: hub_resume [ 2.060998] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 2.061035] device-mapper: uevent: version 1.0.3 [ 2.061222] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com [ 2.065925] usb 1-1: new low-speed USB device number 2 using xhci_hcd [ 2.069952] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 2.069993] hub 2-0:1.0: hub_suspend [ 2.069998] usb usb2: bus auto-suspend, wakeup 1 [ 2.070013] usb usb2: suspend raced with wakeup event [ 2.070015] usb usb2: usb auto-resume [ 2.085888] hub 2-0:1.0: hub_resume [ 2.114073] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 2.114170] hub 2-0:1.0: hub_suspend [ 2.114187] usb usb2: bus auto-suspend, wakeup 1 [ 2.114210] usb usb2: suspend raced with wakeup event [ 2.114215] usb usb2: usb auto-resume [ 2.129987] hub 2-0:1.0: hub_resume [ 2.158111] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 2.158220] hub 2-0:1.0: hub_suspend [ 2.158241] usb usb2: bus auto-suspend, wakeup 1 [ 2.158267] usb usb2: suspend raced with wakeup event [ 2.158272] usb usb2: usb auto-resume [ 2.174035] hub 2-0:1.0: hub_resume [ 2.202117] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 2.202250] hub 2-0:1.0: hub_suspend [ 2.202269] usb usb2: bus auto-suspend, wakeup 1 [ 2.202298] usb usb2: suspend raced with wakeup event [ 2.202303] usb usb2: usb auto-resume [ 2.218002] hub 2-0:1.0: hub_resume [ 2.219261] usb 1-1: skipped 1 descriptor after interface [ 2.219285] usb 1-1: skipped 1 descriptor after interface [ 2.219960] usb 1-1: default language 0x0409 [ 2.222808] usb 1-1: udev 2, busnum 1, minor = 1 [ 2.222826] usb 1-1: New USB device found, idVendor=0bf8, idProduct=101e, bcdDevice= 1.09 [ 2.222837] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.222844] usb 1-1: Product: Fujitsu Keyboard [ 2.222853] usb 1-1: Manufacturer: Fujitsu [ 2.223810] usb 1-1: usb_probe_device [ 2.223822] usb 1-1: configuration #1 chosen from 1 choice [ 2.225073] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 2.225687] usb 1-1: adding 1-1:1.1 (config #1, interface 1) [ 2.226389] usb usb1-port2: status 0301, change 0000, 1.5 Mb/s [ 2.237150] usbhid 1-1:1.0: usb_probe_interface [ 2.237162] usbhid 1-1:1.0: usb_probe_interface - got id [ 2.241224] input: Fujitsu Fujitsu Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.0/0003:0BF8:101E.0002/input/input5 [ 2.246088] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 2.246201] hub 2-0:1.0: hub_suspend [ 2.246224] usb usb2: bus auto-suspend, wakeup 1 [ 2.246252] usb usb2: suspend raced with wakeup event [ 2.246257] usb usb2: usb auto-resume [ 2.262006] hub 2-0:1.0: hub_resume [ 2.290112] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 2.290243] hub 2-0:1.0: hub_suspend [ 2.290262] usb usb2: bus auto-suspend, wakeup 1 [ 2.290291] usb usb2: suspend raced with wakeup event [ 2.290297] usb usb2: usb auto-resume [ 2.298631] hid-generic 0003:0BF8:101E.0002: input,hidraw1: USB HID v1.10 Keyboard [Fujitsu Fujitsu Keyboard] on usb-0000:00:14.0-1/input0 [ 2.298799] usbhid 1-1:1.1: usb_probe_interface [ 2.298816] usbhid 1-1:1.1: usb_probe_interface - got id [ 2.301992] tsc: Refined TSC clocksource calibration: 2904.009 MHz [ 2.302014] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x29dc0e73964, max_idle_ns: 440795294805 ns [ 2.302097] clocksource: Switched to clocksource tsc [ 2.305904] hub 2-0:1.0: hub_resume [ 2.306915] input: Fujitsu Fujitsu Keyboard System Control as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.1/0003:0BF8:101E.0003/input/input6 [ 2.334126] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 2.334240] hub 2-0:1.0: hub_suspend [ 2.334257] usb usb2: bus auto-suspend, wakeup 1 [ 2.354011] usb 1-2: new low-speed USB device number 3 using xhci_hcd [ 2.366164] input: Fujitsu Fujitsu Keyboard Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.1/0003:0BF8:101E.0003/input/input7 [ 2.366190] usbhid 1-1:1.1: looking for a minor, starting at 0 [ 2.366670] hid-generic 0003:0BF8:101E.0003: input,hiddev0,hidraw2: USB HID v1.10 Device [Fujitsu Fujitsu Keyboard] on usb-0000:00:14.0-1/input1 [ 2.366829] usbcore: registered new interface driver usbhid [ 2.366839] usbhid: USB HID core driver [ 2.504692] usb 1-2: skipped 1 descriptor after interface [ 2.505241] usb 1-2: default language 0x0409 [ 2.506865] usb 1-2: udev 3, busnum 1, minor = 2 [ 2.506885] usb 1-2: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00 [ 2.506898] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.506906] usb 1-2: Product: USB Optical Mouse [ 2.506913] usb 1-2: Manufacturer: Logitech [ 2.507759] usb 1-2: usb_probe_device [ 2.507780] usb 1-2: configuration #1 chosen from 1 choice [ 2.508917] usb 1-2: adding 1-2:1.0 (config #1, interface 0) [ 2.509583] usbhid 1-2:1.0: usb_probe_interface [ 2.509600] usbhid 1-2:1.0: usb_probe_interface - got id [ 2.512144] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/0003:046D:C077.0004/input/input8 [ 2.512695] hid-generic 0003:046D:C077.0004: input,hidraw3: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:14.0-2/input0 [ 2.513115] usb usb1-port3: status 0101, change 0000, 12 Mb/s [ 2.638068] usb 1-3: new full-speed USB device number 4 using xhci_hcd [ 2.788553] usb 1-3: udev 4, busnum 1, minor = 3 [ 2.788572] usb 1-3: New USB device found, idVendor=0cf3, idProduct=e300, bcdDevice= 0.01 [ 2.788585] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.789419] usb 1-3: usb_probe_device [ 2.789433] usb 1-3: configuration #1 chosen from 1 choice [ 2.791241] usb 1-3: adding 1-3:1.0 (config #1, interface 0) [ 2.791996] usb 1-3: adding 1-3:1.1 (config #1, interface 1) [ 2.792740] usb usb1-port4: status 0101, change 0000, 12 Mb/s [ 2.918087] usb 1-4: new full-speed USB device number 5 using xhci_hcd [ 3.066035] usb 1-4: ep0 maxpacket = 8 [ 3.068546] usb 1-4: skipped 1 descriptor after interface [ 3.068802] usb 1-4: default language 0x0409 [ 3.069521] usb 1-4: udev 5, busnum 1, minor = 4 [ 3.069541] usb 1-4: New USB device found, idVendor=04f3, idProduct=2234, bcdDevice=11.11 [ 3.069554] usb 1-4: New USB device strings: Mfr=4, Product=14, SerialNumber=0 [ 3.069562] usb 1-4: Product: Touchscreen [ 3.069569] usb 1-4: Manufacturer: ELAN [ 3.070546] usb 1-4: usb_probe_device [ 3.070565] usb 1-4: configuration #1 chosen from 1 choice [ 3.071958] usb 1-4: adding 1-4:1.0 (config #1, interface 0) [ 3.072601] usbhid 1-4:1.0: usb_probe_interface [ 3.072618] usbhid 1-4:1.0: usb_probe_interface - got id [ 3.083230] input: ELAN Touchscreen as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/0003:04F3:2234.0005/input/input9 [ 3.083394] input: ELAN Touchscreen as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/0003:04F3:2234.0005/input/input10 [ 3.083426] input: ELAN Touchscreen as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/0003:04F3:2234.0005/input/input11 [ 3.083431] usbhid 1-4:1.0: looking for a minor, starting at 0 [ 3.083654] hid-generic 0003:04F3:2234.0005: input,hiddev1,hidraw4: USB HID v1.10 Device [ELAN Touchscreen] on usb-0000:00:14.0-4/input0 [ 3.083766] usb usb1-port5: status 0101, change 0000, 12 Mb/s [ 3.210046] usb 1-5: new high-speed USB device number 6 using xhci_hcd [ 3.410108] usb 1-5: skipped 2 descriptors after configuration [ 3.410127] usb 1-5: skipped 6 descriptors after interface [ 3.410138] usb 1-5: skipped 1 descriptor after endpoint [ 3.410147] usb 1-5: skipped 14 descriptors after endpoint [ 3.410969] usb 1-5: default language 0x0409 [ 3.418897] usb 1-5: udev 6, busnum 1, minor = 5 [ 3.418917] usb 1-5: New USB device found, idVendor=0c45, idProduct=670c, bcdDevice=56.26 [ 3.418929] usb 1-5: New USB device strings: Mfr=2, Product=1, SerialNumber=0 [ 3.418937] usb 1-5: Product: Integrated_Webcam_HD [ 3.418944] usb 1-5: Manufacturer: CN09GTFMLOG008C8B7FWA01 [ 3.419890] usb 1-5: usb_probe_device [ 3.419904] usb 1-5: configuration #1 chosen from 1 choice [ 3.421628] usb 1-5: adding 1-5:1.0 (config #1, interface 0) [ 3.425554] usb 1-5: adding 1-5:1.1 (config #1, interface 1) [ 3.429601] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0000 [ 9.253327] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 9.253417] usb usb1-port2: status 0100, change 0001, 12 Mb/s [ 9.253439] usb 1-2: USB disconnect, device number 3 [ 9.253450] usb 1-2: unregistering device [ 9.253457] usb 1-2: unregistering interface 1-2:1.0 [ 9.253697] xhci_hcd 0000:00:14.0: shutdown urb 00000000709db232 ep1in-intr [ 9.274669] usb 1-2: usb_disable_device nuking all URBs [ 9.418016] usb usb1-port2: debounce total 100ms stable 100ms status 0x301 [ 9.546040] usb 1-2: new low-speed USB device number 7 using xhci_hcd [ 9.696520] usb 1-2: skipped 1 descriptor after interface [ 9.696974] usb 1-2: default language 0x0409 [ 9.698665] usb 1-2: udev 7, busnum 1, minor = 6 [ 9.698688] usb 1-2: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00 [ 9.698704] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 9.698713] usb 1-2: Product: USB Optical Mouse [ 9.698722] usb 1-2: Manufacturer: Logitech [ 9.699620] usb 1-2: usb_probe_device [ 9.699634] usb 1-2: configuration #1 chosen from 1 choice [ 9.701495] usb 1-2: adding 1-2:1.0 (config #1, interface 0) [ 9.702174] usbhid 1-2:1.0: usb_probe_interface [ 9.702188] usbhid 1-2:1.0: usb_probe_interface - got id [ 9.704761] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/0003:046D:C077.0006/input/input13 [ 9.705086] hid-generic 0003:046D:C077.0006: input,hidraw3: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:14.0-2/input0 [ 9.705437] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 10.577639] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 10.577736] usb usb1-port2: status 0100, change 0001, 12 Mb/s [ 10.577757] usb 1-2: USB disconnect, device number 7 [ 10.577766] usb 1-2: unregistering device [ 10.577774] usb 1-2: unregistering interface 1-2:1.0 [ 10.578037] xhci_hcd 0000:00:14.0: shutdown urb 000000000c7cdc27 ep1in-intr [ 10.598700] usb 1-2: usb_disable_device nuking all URBs [ 11.174064] usb usb1-port2: debounce total 400ms stable 100ms status 0x100 [ 11.174105] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 16.182169] pci 0000:01:00.0: [8086:1576] type 01 class 0x060400 PCIe Switch Upstream Port [ 16.182229] pci 0000:01:00.0: PCI bridge to [bus 02-39] [ 16.182245] pci 0000:01:00.0: bridge window [mem 0xc4000000-0xda0fffff] [ 16.182263] pci 0000:01:00.0: bridge window [mem 0xa0000000-0xc1ffffff 64bit pref] [ 16.182283] pci 0000:01:00.0: enabling Extended Tags [ 16.182436] pci 0000:01:00.0: supports D1 D2 [ 16.182438] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 16.182578] pci 0000:01:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x2 link at 0000:00:1c.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link) [ 16.183267] pci 0000:02:00.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port [ 16.183321] pci 0000:02:00.0: PCI bridge to [bus 03] [ 16.183336] pci 0000:02:00.0: bridge window [mem 0xda000000-0xda0fffff] [ 16.183379] pci 0000:02:00.0: enabling Extended Tags [ 16.183523] pci 0000:02:00.0: supports D1 D2 [ 16.183524] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 16.183814] pci 0000:02:01.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port [ 16.183867] pci 0000:02:01.0: PCI bridge to [bus 04-38] [ 16.183886] pci 0000:02:01.0: bridge window [mem 0xc4000000-0xd9efffff] [ 16.183904] pci 0000:02:01.0: bridge window [mem 0xa0000000-0xc1ffffff 64bit pref] [ 16.183928] pci 0000:02:01.0: enabling Extended Tags [ 16.184076] pci 0000:02:01.0: supports D1 D2 [ 16.184078] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 16.184364] pci 0000:02:02.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port [ 16.184418] pci 0000:02:02.0: PCI bridge to [bus 39] [ 16.184433] pci 0000:02:02.0: bridge window [mem 0xd9f00000-0xd9ffffff] [ 16.184472] pci 0000:02:02.0: enabling Extended Tags [ 16.184617] pci 0000:02:02.0: supports D1 D2 [ 16.184619] pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 16.184914] pci 0000:01:00.0: PCI bridge to [bus 02-39] [ 16.184993] pci 0000:02:00.0: PCI bridge to [bus 03] [ 16.185077] pci 0000:02:01.0: PCI bridge to [bus 04-38] [ 16.185210] pci 0000:39:00.0: [8086:15b5] type 00 class 0x0c0330 PCIe Endpoint [ 16.185246] pci 0000:39:00.0: BAR 0 [mem 0xd9f00000-0xd9f0ffff] [ 16.185353] pci 0000:39:00.0: enabling Extended Tags [ 16.185518] pci 0000:39:00.0: supports D1 D2 [ 16.185519] pci 0000:39:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 16.185676] pci 0000:39:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x2 link at 0000:00:1c.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link) [ 16.192247] pci 0000:02:02.0: PCI bridge to [bus 39] [ 16.192312] pci_bus 0000:02: Allocating resources [ 16.192334] pci 0000:02:01.0: bridge window [io 0x1000-0x0fff] to [bus 04-38] add_size 1000 [ 16.192338] pci 0000:02:02.0: bridge window [io 0x1000-0x0fff] to [bus 39] add_size 1000 [ 16.192341] pci 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000 [ 16.192344] pci 0000:01:00.0: bridge window [io 0x1000-0x0fff] to [bus 02-39] add_size 2000 [ 16.192348] pci 0000:01:00.0: bridge window [io size 0x2000]: can't assign; no space [ 16.192350] pci 0000:01:00.0: bridge window [io size 0x2000]: failed to assign [ 16.192352] pci 0000:01:00.0: bridge window [io size 0x2000]: can't assign; no space [ 16.192354] pci 0000:01:00.0: bridge window [io size 0x2000]: failed to assign [ 16.192358] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space [ 16.192360] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign [ 16.192361] pci 0000:02:01.0: bridge window [io size 0x1000]: can't assign; no space [ 16.192363] pci 0000:02:01.0: bridge window [io size 0x1000]: failed to assign [ 16.192365] pci 0000:02:02.0: bridge window [io size 0x1000]: can't assign; no space [ 16.192366] pci 0000:02:02.0: bridge window [io size 0x1000]: failed to assign [ 16.192369] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space [ 16.192371] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign [ 16.192372] pci 0000:02:02.0: bridge window [io size 0x1000]: can't assign; no space [ 16.192374] pci 0000:02:02.0: bridge window [io size 0x1000]: failed to assign [ 16.192375] pci 0000:02:01.0: bridge window [io size 0x1000]: can't assign; no space [ 16.192377] pci 0000:02:01.0: bridge window [io size 0x1000]: failed to assign [ 16.192379] pci 0000:02:00.0: PCI bridge to [bus 03] [ 16.192386] pci 0000:02:00.0: bridge window [mem 0xda000000-0xda0fffff] [ 16.192399] pci 0000:02:01.0: PCI bridge to [bus 04-38] [ 16.192406] pci 0000:02:01.0: bridge window [mem 0xc4000000-0xd9efffff] [ 16.192411] pci 0000:02:01.0: bridge window [mem 0xa0000000-0xc1ffffff 64bit pref] [ 16.192420] pci 0000:02:02.0: PCI bridge to [bus 39] [ 16.192427] pci 0000:02:02.0: bridge window [mem 0xd9f00000-0xd9ffffff] [ 16.192440] pci 0000:01:00.0: PCI bridge to [bus 02-39] [ 16.192446] pci 0000:01:00.0: bridge window [mem 0xc4000000-0xda0fffff] [ 16.192451] pci 0000:01:00.0: bridge window [mem 0xa0000000-0xc1ffffff 64bit pref] [ 16.198745] xhci_hcd 0000:39:00.0: xHCI Host Controller [ 16.198756] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus number 3 [ 16.199921] xhci_hcd 0000:39:00.0: hcc params 0x200077c1 hci version 0x110 quirks 0x0000000200009810 [ 16.199932] xhci_hcd 0000:39:00.0: supports USB remote wakeup [ 16.200326] xhci_hcd 0000:39:00.0: xHCI Host Controller [ 16.200331] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus number 4 [ 16.200334] xhci_hcd 0000:39:00.0: Host supports USB 3.1 Enhanced SuperSpeed [ 16.200337] xhci_hcd 0000:39:00.0: supports USB remote wakeup [ 16.201809] usb usb3: default language 0x0409 [ 16.201822] usb usb3: udev 1, busnum 3, minor = 256 [ 16.201825] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.08 [ 16.201828] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.201830] usb usb3: Product: xHCI Host Controller [ 16.201831] usb usb3: Manufacturer: Linux 6.8.0-rc5+ xhci-hcd [ 16.201833] usb usb3: SerialNumber: 0000:39:00.0 [ 16.205871] usb usb3: usb_probe_device [ 16.205876] usb usb3: configuration #1 chosen from 1 choice [ 16.205894] usb usb3: adding 3-0:1.0 (config #1, interface 0) [ 16.205945] hub 3-0:1.0: usb_probe_interface [ 16.205948] hub 3-0:1.0: usb_probe_interface - got id [ 16.205951] hub 3-0:1.0: USB hub found [ 16.205963] hub 3-0:1.0: 2 ports detected [ 16.205965] hub 3-0:1.0: standalone hub [ 16.205967] hub 3-0:1.0: no power switching (usb 1.0) [ 16.205968] hub 3-0:1.0: individual port over-current protection [ 16.205970] hub 3-0:1.0: Single TT [ 16.205972] hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 16.205974] hub 3-0:1.0: power on to power good time: 20ms [ 16.205980] hub 3-0:1.0: local power source is good [ 16.206566] hub 3-0:1.0: trying to enable port power on non-switchable hub [ 16.206785] usb usb4: skipped 1 descriptor after endpoint [ 16.206791] usb usb4: default language 0x0409 [ 16.206803] usb usb4: udev 1, busnum 4, minor = 384 [ 16.206805] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.08 [ 16.206807] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.206809] usb usb4: Product: xHCI Host Controller [ 16.206811] usb usb4: Manufacturer: Linux 6.8.0-rc5+ xhci-hcd [ 16.206812] usb usb4: SerialNumber: 0000:39:00.0 [ 16.206961] usb usb4: usb_probe_device [ 16.206963] usb usb4: configuration #1 chosen from 1 choice [ 16.209808] usb usb4: adding 4-0:1.0 (config #1, interface 0) [ 16.209860] hub 4-0:1.0: usb_probe_interface [ 16.209863] hub 4-0:1.0: usb_probe_interface - got id [ 16.209866] hub 4-0:1.0: USB hub found [ 16.209878] hub 4-0:1.0: 2 ports detected [ 16.209880] hub 4-0:1.0: standalone hub [ 16.209882] hub 4-0:1.0: no power switching (usb 1.0) [ 16.209883] hub 4-0:1.0: individual port over-current protection [ 16.209885] hub 4-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 16.209887] hub 4-0:1.0: power on to power good time: 100ms [ 16.209896] hub 4-0:1.0: local power source is good [ 16.210256] usb usb4-port1: peered to usb3-port1 [ 16.210469] usb usb4: port-1 no _DSM function 5 [ 16.210473] usb usb4: port-2 no _DSM function 5 [ 16.210478] hub 4-0:1.0: trying to enable port power on non-switchable hub [ 16.229803] usb usb3-port1: status 0101 change 0001 [ 16.313812] usb usb4-port1: status 0203 change 0011 [ 16.333801] hub 3-0:1.0: state 7 ports 2 chg 0002 evt 0000 [ 16.333822] usb usb3-port1: status 0101, change 0000, 12 Mb/s [ 16.417809] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000 [ 16.417831] usb usb4-port1: status 0203, change 0000, 10.0 Gb/s [ 16.461856] usb 3-1: new high-speed USB device number 2 using xhci_hcd [ 16.616373] usb 3-1: default language 0x0409 [ 16.617040] usb 3-1: udev 2, busnum 3, minor = 257 [ 16.617047] usb 3-1: New USB device found, idVendor=2109, idProduct=2820, bcdDevice=30.03 [ 16.617053] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 16.617057] usb 3-1: Product: USB2.0 Hub [ 16.617060] usb 3-1: Manufacturer: VIA Labs, Inc. [ 16.617531] usb 3-1: usb_probe_device [ 16.617536] usb 3-1: configuration #1 chosen from 1 choice [ 16.618807] usb 3-1: adding 3-1:1.0 (config #1, interface 0) [ 16.619132] hub 3-1:1.0: usb_probe_interface [ 16.619137] hub 3-1:1.0: usb_probe_interface - got id [ 16.619142] hub 3-1:1.0: USB hub found [ 16.619270] hub 3-1:1.0: 5 ports detected [ 16.619276] hub 3-1:1.0: compound device; port removable status: FFRRF [ 16.619280] hub 3-1:1.0: individual port power switching [ 16.619285] hub 3-1:1.0: individual port over-current protection [ 16.620836] hub 3-1:1.0: TT per port [ 16.620842] hub 3-1:1.0: TT requires at most 32 FS bit times (2664 ns) [ 16.620846] hub 3-1:1.0: Port indicators are supported [ 16.620849] hub 3-1:1.0: power on to power good time: 350ms [ 16.621588] hub 3-1:1.0: local power source is good [ 16.622215] hub 3-1:1.0: enabling power on all ports [ 16.744202] usb 4-1: new SuperSpeed Plus Gen 2x1 USB device number 2 using xhci_hcd [ 16.744439] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 16.764903] usb 4-1: skipped 1 descriptor after endpoint [ 16.765520] usb 4-1: default language 0x0409 [ 16.766151] usb 4-1: udev 2, busnum 4, minor = 385 [ 16.766163] usb 4-1: New USB device found, idVendor=2109, idProduct=0820, bcdDevice=30.03 [ 16.766172] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 16.766177] usb 4-1: Product: USB3.1 Hub [ 16.766182] usb 4-1: Manufacturer: VIA Labs, Inc. [ 16.766840] usb 4-1: usb_probe_device [ 16.766847] usb 4-1: configuration #1 chosen from 1 choice [ 16.768602] usb 4-1: adding 4-1:1.0 (config #1, interface 0) [ 16.769088] hub 4-1:1.0: usb_probe_interface [ 16.769096] hub 4-1:1.0: usb_probe_interface - got id [ 16.769103] hub 4-1:1.0: USB hub found [ 16.769256] hub 4-1:1.0: 4 ports detected [ 16.769262] hub 4-1:1.0: standalone hub [ 16.769266] hub 4-1:1.0: individual port power switching [ 16.769270] hub 4-1:1.0: individual port over-current protection [ 16.769273] hub 4-1:1.0: TT requires at most 8 FS bit times (666 ns) [ 16.769278] hub 4-1:1.0: power on to power good time: 350ms [ 16.769904] hub 4-1:1.0: local power source is good [ 16.769975] usb 4-1-port1: peered to 3-1-port1 [ 16.770022] usb 4-1-port2: peered to 3-1-port2 [ 16.770061] usb 4-1-port3: peered to 3-1-port3 [ 16.770101] usb 4-1-port4: peered to 3-1-port4 [ 16.771225] hub 4-1:1.0: enabling power on all ports [ 16.772721] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 16.775697] PM: Image not found (code -22) [ 16.921110] EXT4-fs (dm-0): mounted filesystem 32e29882-d94d-4a92-9ee4-4d03002bfa29 ro with ordered data mode. Quota mode: none. [ 16.946585] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 17.045332] systemd[1]: Inserted module 'autofs4' [ 17.089727] systemd[1]: systemd 255.3-2 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) [ 17.089742] systemd[1]: Detected architecture x86-64. [ 17.090821] systemd[1]: Hostname set to <abreu>. [ 17.118047] usb 3-1-port1: status 0101 change 0001 [ 17.150317] usb 4-1-port2: status 0203 change 0011 [ 17.221964] hub 3-1:1.0: state 7 ports 5 chg 0002 evt 0000 [ 17.222417] usb 3-1-port1: status 0101, change 0000, 12 Mb/s [ 17.222848] usb 3-1-port1: indicator auto status 0 [ 17.243212] systemd[1]: Queued start job for default target graphical.target. [ 17.253794] hub 4-1:1.0: state 7 ports 4 chg 0004 evt 0000 [ 17.270795] systemd[1]: Created slice system-getty.slice - Slice /system/getty. [ 17.271133] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe. [ 17.271395] systemd[1]: Created slice system-systemd\x2dcryptsetup.slice - Encrypted Volume Units Service Slice. [ 17.271653] systemd[1]: Created slice system-systemd\x2dfsck.slice - Slice /system/systemd-fsck. [ 17.271855] systemd[1]: Created slice user.slice - User and Session Slice. [ 17.271918] systemd[1]: Started systemd-ask-password-console.path - Dispatch Password Requests to Console Directory Watch. [ 17.271964] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch. [ 17.272130] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point. [ 17.272148] systemd[1]: Expecting device dev-disk-by\x2ddiskseq-1\x2dpart4.device - /dev/disk/by-diskseq/1-part4... [ 17.272155] systemd[1]: Expecting device dev-disk-by\x2duuid-2d23fd4c\x2d5d03\x2d4e1a\x2d8a42\x2d0e859d1f00d8.device - /dev/disk/by-uuid/2d23fd4c-5d03-4e1a-8a42-0e859d1f00d8... [ 17.272160] systemd[1]: Expecting device dev-disk-by\x2duuid-61be8f50\x2d69c5\x2d49a5\x2dbcad\x2d3f4521e9c7b5.device - /dev/disk/by-uuid/61be8f50-69c5-49a5-bcad-3f4521e9c7b5... [ 17.272165] systemd[1]: Expecting device dev-disk-by\x2duuid-96BD\x2d5653.device - /dev/disk/by-uuid/96BD-5653... [ 17.272183] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes. [ 17.272200] systemd[1]: Reached target nss-user-lookup.target - User and Group Name Lookups. [ 17.272210] systemd[1]: Reached target paths.target - Path Units. [ 17.272222] systemd[1]: Reached target remote-fs.target - Remote File Systems. [ 17.272231] systemd[1]: Reached target slices.target - Slice Units. [ 17.272259] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes. [ 17.273417] systemd[1]: Listening on systemd-coredump.socket - Process Core Dump Socket. [ 17.273507] systemd[1]: Listening on systemd-fsckd.socket - fsck to fsckd communication Socket. [ 17.273558] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe. [ 17.273673] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log). [ 17.273805] systemd[1]: Listening on systemd-journald.socket - Journal Socket. [ 17.273840] systemd[1]: systemd-pcrextend.socket - TPM2 PCR Extension (Varlink) was skipped because of an unmet condition check (ConditionSecurity=measured-uki). [ 17.273940] usb 4-1-port2: status 0203, change 0000, 10.0 Gb/s [ 17.274148] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket. [ 17.274241] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket. [ 17.275362] systemd[1]: Mounting dev-hugepages.mount - Huge Pages File System... [ 17.276311] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System... [ 17.277375] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System... [ 17.281819] systemd[1]: Mounting sys-kernel-tracing.mount - Kernel Trace File System... [ 17.284669] systemd[1]: Starting keyboard-setup.service - Set the console keyboard layout... [ 17.287863] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes... [ 17.289275] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs... [ 17.294479] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod... [ 17.303077] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm... [ 17.310090] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore... [ 17.312218] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse... [ 17.321971] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop... [ 17.322107] systemd[1]: systemd-fsck-root.service - File System Check on Root Device was skipped because of an unmet condition check (ConditionPathExists=!/run/initramfs/fsck-root). [ 17.327057] systemd[1]: Starting systemd-journald.service - Journal Service... [ 17.328849] pstore: Using crash dump compression: deflate [ 17.333390] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules... [ 17.333418] systemd[1]: systemd-pcrmachine.service - TPM2 PCR Machine ID Measurement was skipped because of an unmet condition check (ConditionSecurity=measured-uki). [ 17.337349] systemd[1]: Starting systemd-remount-fs.service - Remount Root and Kernel File Systems... [ 17.337455] systemd[1]: systemd-tpm2-setup-early.service - TPM2 SRK Setup (Early) was skipped because of an unmet condition check (ConditionSecurity=measured-uki). [ 17.340649] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices... [ 17.341907] pstore: Registered efi_pstore as persistent store backend [ 17.346380] systemd[1]: Mounted dev-hugepages.mount - Huge Pages File System. [ 17.346533] systemd[1]: Mounted dev-mqueue.mount - POSIX Message Queue File System. [ 17.346661] systemd[1]: Mounted sys-kernel-debug.mount - Kernel Debug File System. [ 17.346775] systemd[1]: Mounted sys-kernel-tracing.mount - Kernel Trace File System. [ 17.347387] systemd[1]: Finished keyboard-setup.service - Set the console keyboard layout. [ 17.347729] systemd[1]: Finished kmod-static-nodes.service - Create List of Static Device Nodes. [ 17.348027] systemd[1]: modprobe@configfs.service: Deactivated successfully. [ 17.348184] systemd[1]: Finished modprobe@configfs.service - Load Kernel Module configfs. [ 17.349188] loop: module loaded [ 17.349596] systemd[1]: modprobe@dm_mod.service: Deactivated successfully. [ 17.349926] systemd[1]: Finished modprobe@dm_mod.service - Load Kernel Module dm_mod. [ 17.350373] systemd[1]: modprobe@drm.service: Deactivated successfully. [ 17.350535] systemd[1]: Finished modprobe@drm.service - Load Kernel Module drm. [ 17.350853] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully. [ 17.351009] systemd[1]: Finished modprobe@efi_pstore.service - Load Kernel Module efi_pstore. [ 17.351346] systemd[1]: modprobe@fuse.service: Deactivated successfully. [ 17.351501] systemd[1]: Finished modprobe@fuse.service - Load Kernel Module fuse. [ 17.351864] systemd[1]: modprobe@loop.service: Deactivated successfully. [ 17.352022] systemd[1]: Finished modprobe@loop.service - Load Kernel Module loop. [ 17.353795] usb 3-1.1: new full-speed USB device number 3 using xhci_hcd [ 17.353929] systemd[1]: Mounting sys-fs-fuse-connections.mount - FUSE Control File System... [ 17.356813] systemd[1]: Mounting sys-kernel-config.mount - Kernel Configuration File System... [ 17.356890] systemd[1]: systemd-repart.service - Repartition Root Disk was skipped because no trigger condition checks were met. [ 17.363585] systemd[1]: Starting systemd-tmpfiles-setup-dev-early.service - Create Static Device Nodes in /dev gracefully... [ 17.364225] lp: driver loaded but no devices found [ 17.365648] systemd[1]: Mounted sys-kernel-config.mount - Kernel Configuration File System. [ 17.369161] ppdev: user-space parallel port driver [ 17.369901] systemd-journald[411]: Collecting audit messages is disabled. [ 17.370578] systemd[1]: Mounted sys-fs-fuse-connections.mount - FUSE Control File System. [ 17.380336] EXT4-fs (dm-0): re-mounted 32e29882-d94d-4a92-9ee4-4d03002bfa29 r/w. Quota mode: none. [ 17.382961] systemd[1]: Finished systemd-remount-fs.service - Remount Root and Kernel File Systems. [ 17.383782] systemd[1]: systemd-hwdb-update.service - Rebuild Hardware Database was skipped because of an unmet condition check (ConditionNeedsUpdate=/etc). [ 17.385194] systemd[1]: Starting systemd-pstore.service - Platform Persistent Storage Archival... [ 17.390190] systemd[1]: Starting systemd-random-seed.service - Load/Save OS Random Seed... [ 17.390232] systemd[1]: systemd-tpm2-setup.service - TPM2 SRK Setup was skipped because of an unmet condition check (ConditionSecurity=measured-uki). [ 17.394232] systemd[1]: Finished systemd-tmpfiles-setup-dev-early.service - Create Static Device Nodes in /dev gracefully. [ 17.394434] systemd[1]: systemd-sysusers.service - Create System Users was skipped because no trigger condition checks were met. [ 17.398042] systemd[1]: Starting systemd-tmpfiles-setup-dev.service - Create Static Device Nodes in /dev... [ 17.398435] systemd[1]: Finished systemd-modules-load.service - Load Kernel Modules. [ 17.402521] systemd[1]: Starting systemd-sysctl.service - Apply Kernel Variables... [ 17.468086] systemd[1]: Finished systemd-random-seed.service - Load/Save OS Random Seed. [ 17.489597] systemd[1]: Finished systemd-sysctl.service - Apply Kernel Variables. [ 17.500340] systemd[1]: Finished systemd-tmpfiles-setup-dev.service - Create Static Device Nodes in /dev. [ 17.502912] systemd[1]: Reached target local-fs-pre.target - Preparation for Local File Systems. [ 17.528144] usb 3-1.1: skipped 1 descriptor after interface [ 17.533653] usb 3-1.1: default language 0x0409 [ 17.548462] usb 3-1.1: udev 3, busnum 3, minor = 258 [ 17.548474] usb 3-1.1: New USB device found, idVendor=06c4, idProduct=c412, bcdDevice= 0.06 [ 17.548481] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.548485] usb 3-1.1: Product: DELL DA300 [ 17.548489] usb 3-1.1: Manufacturer: Bizlink [ 17.548492] usb 3-1.1: SerialNumber: MCU Ver0006 [ 17.548728] usb 3-1.1: usb_probe_device [ 17.548733] usb 3-1.1: configuration #1 chosen from 1 choice [ 17.560564] systemd[1]: Starting systemd-udevd.service - Rule-based Manager for Device Events and Files... [ 17.575825] usb 3-1.1: adding 3-1.1:1.0 (config #1, interface 0) [ 17.582606] usbhid 3-1.1:1.0: usb_probe_interface [ 17.582615] usbhid 3-1.1:1.0: usb_probe_interface - got id [ 17.591771] usbhid 3-1.1:1.0: looking for a minor, starting at 0 [ 17.591890] hid-generic 0003:06C4:C412.0007: hiddev2,hidraw3: USB HID v1.11 Device [Bizlink DELL DA300] on usb-0000:39:00.0-1.1/input0 [ 17.592739] systemd[1]: Finished systemd-pstore.service - Platform Persistent Storage Archival. [ 17.613918] usb 4-1.2: new SuperSpeed USB device number 3 using xhci_hcd [ 17.633911] usb 4-1.2: USB quirks for this device: 400 [ 17.634085] usb 4-1.2: skipped 1 descriptor after endpoint [ 17.634088] usb 4-1.2: skipped 1 descriptor after endpoint [ 17.634090] usb 4-1.2: skipped 1 descriptor after endpoint [ 17.634169] usb 4-1.2: skipped 3 descriptors after interface [ 17.634171] usb 4-1.2: skipped 1 descriptor after endpoint [ 17.634173] usb 4-1.2: skipped 1 descriptor after endpoint [ 17.634174] usb 4-1.2: skipped 1 descriptor after endpoint [ 17.634210] usb 4-1.2: default language 0x0409 [ 17.634329] usb 4-1.2: udev 3, busnum 4, minor = 386 [ 17.634332] usb 4-1.2: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=31.00 [ 17.634335] usb 4-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=6 [ 17.634337] usb 4-1.2: Product: USB 10/100/1000 LAN [ 17.634339] usb 4-1.2: Manufacturer: Realtek [ 17.634340] usb 4-1.2: SerialNumber: 001000001 [ 17.634445] usb 4-1.2: usb_probe_device [ 17.634448] usb 4-1.2: configuration #2 chosen from 2 choices [ 17.635580] usb 4-1.2: adding 4-1.2:2.0 (config #2, interface 0) [ 17.635712] usb 4-1.2: adding 4-1.2:2.1 (config #2, interface 1) [ 17.686035] systemd[1]: Started systemd-journald.service - Journal Service. [ 17.717920] systemd-journald[411]: Received client request to flush runtime journal. [ 17.734749] systemd-journald[411]: /var/log/journal/16ae67b9dca94ecebbc8ec78ab24e074/system.journal: Journal file uses a different sequence number ID, rotating. [ 17.734756] systemd-journald[411]: Rotating system journal. [ 17.818975] usbcore: registered new device driver r8152-cfgselector [ 17.819001] usb 4-1.2: unregistering interface 4-1.2:2.0 [ 17.819064] usb 4-1.2: unregistering interface 4-1.2:2.1 [ 17.829754] usb 4-1.2: usb_disable_device nuking non-ep0 URBs [ 17.836220] r8152-cfgselector 4-1.2: usb_probe_device [ 17.844122] r8152-cfgselector 4-1.2: adding 4-1.2:1.0 (config #1, interface 0) [ 17.844809] r8152 4-1.2:1.0: usb_probe_interface [ 17.844812] r8152 4-1.2:1.0: usb_probe_interface - got id [ 17.864371] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 17.877887] usb 1-3: usb auto-suspend, wakeup 0 [ 17.879512] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input14 [ 17.910546] input: Intel HID events as /devices/platform/INT33D5:00/input/input15 [ 17.913885] Consider using thermal netlink events interface [ 17.914464] ACPI: AC: AC Adapter [AC] (off-line) [ 17.932219] r8152-cfgselector 4-1.2: reset SuperSpeed USB device number 3 using xhci_hcd [ 17.935926] wmi_bus wmi_bus-PNP0C14:01: WQBC data block query control method not found [ 17.949982] r8152-cfgselector 4-1.2: USB quirks for this device: 400 [ 17.956766] r8152 4-1.2:1.0 (unnamed net_device) (uninitialized): Using pass-thru MAC addr 18:db:f2:2d:cc:f3 [ 17.957090] intel-hid INT33D5:00: platform supports 5 button array [ 17.957157] input: Intel HID 5 button array as /devices/platform/INT33D5:00/input/input16 [ 17.961650] input: DLL075B:01 06CB:76AF Mouse as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-2/i2c-DLL075B:01/0018:06CB:76AF.0001/input/input17 [ 17.962245] input: DLL075B:01 06CB:76AF Touchpad as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-2/i2c-DLL075B:01/0018:06CB:76AF.0001/input/input18 [ 17.962483] hid-multitouch 0018:06CB:76AF.0001: input,hidraw0: I2C HID v1.00 Mouse [DLL075B:01 06CB:76AF] on i2c-DLL075B:01 [ 17.965829] ACPI: button: Lid Switch [LID0] [ 17.966249] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input20 [ 17.966266] input: Intel Virtual Buttons as /devices/pci0000:00/0000:00:1f.0/PNP0C09:00/INT33D6:00/input/input21 [ 17.974692] r8152 4-1.2:1.0: load rtl8153b-2 v2 04/27/23 successfully [ 17.980932] ACPI: battery: Slot [BAT0] (battery present) [ 17.991426] Adding 8387904k swap on /dev/nvme0n1p4. Priority:-2 extents:1 across:8387904k SS [ 18.023923] r8152 4-1.2:1.0 eth0: v1.12.13 [ 18.039327] intel_pmc_core INT33A1:00: initialized [ 18.040568] usbcore: registered new interface driver r8152 [ 18.053028] ACPI: button: Power Button [PBTN] [ 18.053112] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input22 [ 18.059861] usbcore: registered new interface driver cdc_ether [ 18.065429] usbcore: registered new interface driver r8153_ecm [ 18.075739] proc_thermal 0000:00:04.0: enabling device (0000 -> 0002) [ 18.105755] intel_rapl_common: Found RAPL domain package [ 18.105764] intel_rapl_common: Found RAPL domain dram [ 18.107727] usbhid 1-4:1.0: removing 1 minor [ 18.112067] ACPI: button: Sleep Button [SBTN] [ 18.126521] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input24 [ 18.135619] ACPI: button: Power Button [PWRF] [ 18.142803] EXT4-fs (nvme0n1p2): mounted filesystem 2d23fd4c-5d03-4e1a-8a42-0e859d1f00d8 r/w with ordered data mode. Quota mode: none. [ 18.159556] input: ELAN Touchscreen as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/0003:04F3:2234.0005/input/input25 [ 18.199173] input: ELAN Touchscreen UNKNOWN as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/0003:04F3:2234.0005/input/input26 [ 18.199354] input: ELAN Touchscreen UNKNOWN as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/0003:04F3:2234.0005/input/input27 [ 18.199525] usbhid 1-4:1.0: looking for a minor, starting at 0 [ 18.199799] hid-multitouch 0003:04F3:2234.0005: input,hiddev1,hidraw4: USB HID v1.10 Device [ELAN Touchscreen] on usb-0000:00:14.0-4/input0 [ 18.203290] mc: Linux media interface: v0.10 [ 18.249681] videodev: Linux video capture interface: v2.00 [ 18.278210] mei_me 0000:00:16.0: enabling device (0000 -> 0002) [ 18.339025] input: PC Speaker as /devices/platform/pcspkr/input/input29 [ 18.342042] iTCO_vendor_support: vendor-support=0 [ 18.360850] iTCO_wdt iTCO_wdt: Found a Intel PCH TCO device (Version=4, TCOBASE=0x0400) [ 18.367499] iTCO_wdt iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 18.425754] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 18.425796] usb usb1-port2: status 0301, change 0001, 1.5 Mb/s [ 18.581809] usb usb1-port2: debounce total 100ms stable 100ms status 0x301 [ 18.709799] usb 1-2: new low-speed USB device number 8 using xhci_hcd [ 18.859594] usb 1-2: skipped 1 descriptor after interface [ 18.859883] usb 1-2: default language 0x0409 [ 18.861334] usb 1-2: udev 8, busnum 1, minor = 7 [ 18.861338] usb 1-2: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00 [ 18.861341] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 18.861343] usb 1-2: Product: USB Optical Mouse [ 18.861345] usb 1-2: Manufacturer: Logitech [ 18.861550] usb 1-2: usb_probe_device [ 18.861553] usb 1-2: configuration #1 chosen from 1 choice [ 18.862236] usb 1-2: adding 1-2:1.0 (config #1, interface 0) [ 18.862346] usbhid 1-2:1.0: usb_probe_interface [ 18.862349] usbhid 1-2:1.0: usb_probe_interface - got id [ 18.863670] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/0003:046D:C077.0008/input/input30 [ 18.863877] hid-generic 0003:046D:C077.0008: input,hidraw5: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:14.0-2/input0 [ 19.073112] Console: switching to colour dummy device 80x25 [ 19.073159] i915 0000:00:02.0: vgaarb: deactivate vga console [ 19.092429] Bluetooth: Core ver 2.22 [ 19.092453] NET: Registered PF_BLUETOOTH protocol family [ 19.092454] Bluetooth: HCI device and connection manager initialized [ 19.092458] Bluetooth: HCI socket layer initialized [ 19.092460] Bluetooth: L2CAP socket layer initialized [ 19.092464] Bluetooth: SCO socket layer initialized [ 19.092717] uvcvideo 1-5:1.0: usb_probe_interface [ 19.092720] uvcvideo 1-5:1.0: usb_probe_interface - got id [ 19.097877] usb 1-5: Found UVC 1.00 device Integrated_Webcam_HD (0c45:670c) [ 19.122957] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 19.123152] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 19.126416] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 19.128431] intel_rapl_common: Found RAPL domain package [ 19.128435] intel_rapl_common: Found RAPL domain core [ 19.128436] intel_rapl_common: Found RAPL domain uncore [ 19.128438] intel_rapl_common: Found RAPL domain dram [ 19.128439] intel_rapl_common: Found RAPL domain psys [ 19.131084] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 19.145423] RAPL PMU: API unit is 2^-32 Joules, 5 fixed counters, 655360 ms ovfl timer [ 19.145426] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules [ 19.145428] RAPL PMU: hw unit of domain package 2^-14 Joules [ 19.145428] RAPL PMU: hw unit of domain dram 2^-14 Joules [ 19.145429] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules [ 19.145430] RAPL PMU: hw unit of domain psys 2^-14 Joules [ 19.146092] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 19.149761] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4) [ 19.152615] usbcore: registered new interface driver uvcvideo [ 19.180413] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0000 [ 19.225896] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0008 [ 19.232589] usb 1-3: usb auto-resume [ 19.284318] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380 [ 19.284342] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002) [ 19.297815] usb 1-3: Waited 0ms for CONNECT [ 19.297822] usb 1-3: finish resume [ 19.298051] btusb 1-3:1.0: usb_probe_interface [ 19.298055] btusb 1-3:1.0: usb_probe_interface - got id [ 19.298120] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380 [ 19.299130] usbcore: registered new interface driver btusb [ 19.300184] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380 [ 19.301921] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin [ 19.301926] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111 [ 19.311134] audit: type=1400 audit(1708510994.436:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=586 comm="apparmor_parser" [ 19.311141] audit: type=1400 audit(1708510994.436:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=586 comm="apparmor_parser" [ 19.311143] audit: type=1400 audit(1708510994.440:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=585 comm="apparmor_parser" [ 19.315836] r8152 4-1.2:1.0 enx18dbf22dccf3: renamed from eth0 [ 19.371235] audit: type=1400 audit(1708510994.456:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=592 comm="apparmor_parser" [ 19.371241] audit: type=1400 audit(1708510994.456:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=592 comm="apparmor_parser" [ 19.371244] audit: type=1400 audit(1708510994.456:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=592 comm="apparmor_parser" [ 19.371245] audit: type=1400 audit(1708510994.468:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/ipsec/charon" pid=595 comm="apparmor_parser" [ 19.371247] audit: type=1400 audit(1708510994.472:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=587 comm="apparmor_parser" [ 19.371249] audit: type=1400 audit(1708510994.472:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=587 comm="apparmor_parser" [ 19.371251] audit: type=1400 audit(1708510994.472:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=587 comm="apparmor_parser" [ 19.408892] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915]) [ 19.444382] input: Dell WMI hotkeys as /devices/platform/PNP0C14:01/wmi_bus/wmi_bus-PNP0C14:01/9DBB5994-A997-11DA-B012-B622A1EF5492/input/input31 [ 19.449108] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380 [ 19.626304] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380 [ 19.643193] ath10k_pci 0000:3a:00.0: enabling device (0000 -> 0002) [ 19.657415] ath10k_pci 0000:3a:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 19.667569] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin [ 19.695513] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. [ 19.725090] snd_soc_skl 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380 [ 19.803332] snd_soc_avs 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380 [ 19.809492] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380 [ 19.809883] snd_soc_skl 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380 [ 19.809894] snd_soc_avs 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380 [ 19.910412] sof-audio-pci-intel-skl 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380 [ 19.971346] ath10k_pci 0000:3a:00.0: qca6174 hw3.2 target 0x05030000 chip_id 0x00340aff sub 1a56:1535 [ 19.971354] ath10k_pci 0000:3a:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0 [ 19.971932] ath10k_pci 0000:3a:00.0: firmware ver WLAN.RM.4.4.1-00288- api 6 features wowlan,ignore-otp,mfp crc32 bf907c7c [ 20.052062] ath10k_pci 0000:3a:00.0: board_file api 2 bmi_id N/A crc32 d2863f91 [ 20.157873] ath10k_pci 0000:3a:00.0: htt-ver 3.87 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1 [ 20.241272] ath: EEPROM regdomain: 0x6c [ 20.241277] ath: EEPROM indicates we should expect a direct regpair map [ 20.241280] ath: Country alpha2 being used: 00 [ 20.241281] ath: Regpair used: 0x6c [ 20.247875] ath10k_pci 0000:3a:00.0 wlp58s0: renamed from wlan0 [ 20.264359] NET: Registered PF_QIPCRTR protocol family [ 20.314922] i915 0000:00:02.0: [drm] [ENCODER:102:DDI B/PHY B] is disabled/in DSI mode with an ungated DDI clock, gate it [ 20.319436] i915 0000:00:02.0: [drm] [ENCODER:113:DDI C/PHY C] is disabled/in DSI mode with an ungated DDI clock, gate it [ 20.357925] [drm] Initialized i915 1.6.0 20230929 for 0000:00:02.0 on minor 0 [ 20.366613] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 20.367358] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input32 [ 20.369824] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380 [ 20.369873] i915 display info: display version: 9 [ 20.369881] i915 display info: cursor_needs_physical: no [ 20.369886] i915 display info: has_cdclk_crawl: no [ 20.369891] i915 display info: has_cdclk_squash: no [ 20.369896] i915 display info: has_ddi: yes [ 20.369901] i915 display info: has_dp_mst: yes [ 20.369905] i915 display info: has_dsb: no [ 20.369909] i915 display info: has_fpga_dbg: yes [ 20.369914] i915 display info: has_gmch: no [ 20.369917] i915 display info: has_hotplug: yes [ 20.369921] i915 display info: has_hti: no [ 20.369924] i915 display info: has_ipc: yes [ 20.369928] i915 display info: has_overlay: no [ 20.369931] i915 display info: has_psr: yes [ 20.369935] i915 display info: has_psr_hw_tracking: yes [ 20.369939] i915 display info: overlay_needs_physical: no [ 20.369943] i915 display info: supports_tv: no [ 20.369946] i915 display info: has_hdcp: yes [ 20.369950] i915 display info: has_dmc: yes [ 20.369953] i915 display info: has_dsc: no [ 20.439393] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) [ 20.473223] fbcon: i915drmfb (fb0) is primary device [ 20.473561] i915 0000:00:02.0: [drm] Reducing the compressed framebuffer size. This may lead to less power savings than a non-reduced-size. Try to increase stolen memory size if available in BIOS. [ 20.630672] Console: switching to colour frame buffer device 200x56 [ 20.667540] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device [ 20.814297] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC3246: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker [ 20.814303] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) [ 20.814305] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0) [ 20.814306] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0 [ 20.814358] snd_hda_codec_realtek hdaudioC0D0: inputs: [ 20.814359] snd_hda_codec_realtek hdaudioC0D0: Headset Mic=0x19 [ 20.814360] snd_hda_codec_realtek hdaudioC0D0: Headphone Mic=0x1a [ 20.814362] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x12 [ 20.879657] Initializing XFRM netlink socket [ 20.884718] PPP generic driver version 2.4.2 [ 20.912432] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1f.3/sound/card0/input33 [ 20.912599] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input34 [ 20.912736] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input35 [ 20.912867] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input36 [ 20.912986] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input37 [ 20.961912] r8152 4-1.2:1.0 enx18dbf22dccf3: carrier on [ 21.160407] NET: Registered PF_PPPOX protocol family [ 21.175286] IPsec XFRM device driver [ 21.205093] l2tp_core: L2TP core driver, V2.0 [ 21.211109] l2tp_netlink: L2TP netlink interface [ 21.215594] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 21.669834] usb 1-5: usb auto-suspend, wakeup 0 [ 22.386060] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0000 [ 22.433836] usb 1-5: usb auto-resume [ 22.433883] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0020 [ 22.501798] usb 1-5: Waited 0ms for CONNECT [ 22.501805] usb 1-5: finish resume [ 22.503009] usb 1-5: disable remote wakeup, status -32 [ 24.597081] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 24.597238] usb usb1-port2: status 0100, change 0001, 12 Mb/s [ 24.597277] usb 1-2: USB disconnect, device number 8 [ 24.597296] usb 1-2: unregistering device [ 24.597311] usb 1-2: unregistering interface 1-2:1.0 [ 24.597642] xhci_hcd 0000:00:14.0: shutdown urb 00000000568afc33 ep1in-intr [ 24.646050] usb 1-2: usb_disable_device nuking all URBs [ 24.861809] usb usb1-port2: debounce total 150ms stable 100ms status 0x301 [ 24.965884] rfkill: input handler disabled [ 24.993808] usb 1-2: new low-speed USB device number 9 using xhci_hcd [ 25.151568] usb 1-2: skipped 1 descriptor after interface [ 25.151851] usb 1-2: default language 0x0409 [ 25.153239] usb 1-2: udev 9, busnum 1, minor = 8 [ 25.153244] usb 1-2: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00 [ 25.153248] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 25.153250] usb 1-2: Product: USB Optical Mouse [ 25.153252] usb 1-2: Manufacturer: Logitech [ 25.153524] usb 1-2: usb_probe_device [ 25.153528] usb 1-2: configuration #1 chosen from 1 choice [ 25.154226] usb 1-2: adding 1-2:1.0 (config #1, interface 0) [ 25.154389] usbhid 1-2:1.0: usb_probe_interface [ 25.154392] usbhid 1-2:1.0: usb_probe_interface - got id [ 25.157457] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/0003:046D:C077.0009/input/input38 [ 25.157759] hid-generic 0003:046D:C077.0009: input,hidraw5: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:14.0-2/input0 [ 25.158287] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 27.065832] usb 1-5: usb auto-suspend, wakeup 0 [ 27.662767] systemd-journald[411]: /var/log/journal/16ae67b9dca94ecebbc8ec78ab24e074/user-5272.journal: Journal file uses a different sequence number ID, rotating. [ 28.093727] rfkill: input handler enabled [ 31.360808] wlp58s0: authenticate with 6c:f3:7f:10:ae:18 (local address=9c:b6:d0:d1:6a:b1) [ 31.360814] wlp58s0: send auth to 6c:f3:7f:10:ae:18 (try 1/3) [ 31.367486] wlp58s0: authenticated [ 31.367805] wlp58s0: VHT capa missing/short, disabling VHT/HE/EHT [ 31.369796] wlp58s0: associate with 6c:f3:7f:10:ae:18 (try 1/3) [ 31.381564] wlp58s0: RX AssocResp from 6c:f3:7f:10:ae:18 (capab=0x411 status=0 aid=3) [ 31.384002] wlp58s0: associated [ 31.698359] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0000 [ 31.713840] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0000 [ 31.745832] usb 1-5: usb auto-resume [ 31.746011] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0020 [ 31.813800] usb 1-5: Waited 0ms for CONNECT [ 31.813806] usb 1-5: finish resume [ 31.814928] usb 1-5: disable remote wakeup, status -32 [ 33.000692] rfkill: input handler disabled [ 34.333811] usb 1-5: usb auto-suspend, wakeup 0 [ 39.402433] wlp58s0: deauthenticating from 6c:f3:7f:10:ae:18 by local choice (Reason: 3=DEAUTH_LEAVING) [ 487.199776] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 487.199869] usb usb1-port2: status 0100, change 0001, 12 Mb/s [ 487.199890] usb 1-2: USB disconnect, device number 9 [ 487.199900] usb 1-2: unregistering device [ 487.199909] usb 1-2: unregistering interface 1-2:1.0 [ 487.200129] xhci_hcd 0000:00:14.0: shutdown urb 00000000bb402149 ep1in-intr [ 487.243690] usb 1-2: usb_disable_device nuking all URBs [ 487.683204] usb usb1-port2: debounce total 300ms stable 100ms status 0x301 [ 487.811239] usb 1-2: new low-speed USB device number 10 using xhci_hcd [ 487.961378] usb 1-2: skipped 1 descriptor after interface [ 487.962317] usb 1-2: default language 0x0409 [ 487.964441] usb 1-2: udev 10, busnum 1, minor = 9 [ 487.964462] usb 1-2: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00 [ 487.964475] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 487.964483] usb 1-2: Product: USB Optical Mouse [ 487.964490] usb 1-2: Manufacturer: Logitech [ 487.965296] usb 1-2: usb_probe_device [ 487.965309] usb 1-2: configuration #1 chosen from 1 choice [ 487.966389] usb 1-2: adding 1-2:1.0 (config #1, interface 0) [ 487.967091] usbhid 1-2:1.0: usb_probe_interface [ 487.967107] usbhid 1-2:1.0: usb_probe_interface - got id [ 487.969630] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/0003:046D:C077.000A/input/input39 [ 487.971250] hid-generic 0003:046D:C077.000A: input,hidraw5: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:14.0-2/input0 [ 487.971672] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 490.820926] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 490.821000] usb usb1-port2: status 0100, change 0001, 12 Mb/s [ 490.821018] usb 1-2: USB disconnect, device number 10 [ 490.821026] usb 1-2: unregistering device [ 490.821033] usb 1-2: unregistering interface 1-2:1.0 [ 490.821229] xhci_hcd 0000:00:14.0: shutdown urb 00000000d14f3e5c ep1in-intr [ 490.859177] usb 1-2: usb_disable_device nuking all URBs [ 491.006988] usb usb1-port2: debounce total 100ms stable 100ms status 0x301 [ 491.135125] usb 1-2: new low-speed USB device number 11 using xhci_hcd [ 491.285096] usb 1-2: skipped 1 descriptor after interface [ 491.285532] usb 1-2: default language 0x0409 [ 491.286995] usb 1-2: udev 11, busnum 1, minor = 10 [ 491.287014] usb 1-2: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00 [ 491.287027] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 491.287035] usb 1-2: Product: USB Optical Mouse [ 491.287042] usb 1-2: Manufacturer: Logitech [ 491.287957] usb 1-2: usb_probe_device [ 491.287978] usb 1-2: configuration #1 chosen from 1 choice [ 491.289008] usb 1-2: adding 1-2:1.0 (config #1, interface 0) [ 491.289715] usbhid 1-2:1.0: usb_probe_interface [ 491.289733] usbhid 1-2:1.0: usb_probe_interface - got id [ 491.292046] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/0003:046D:C077.000B/input/input40 [ 491.292693] hid-generic 0003:046D:C077.000B: input,hidraw5: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:14.0-2/input0 [ 491.293081] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 517.995156] warning: `musescore3' uses wireless extensions which will stop working for Wi-Fi 7 hardware; use nl80211 [ 613.290973] usb 3-1.1: usb auto-suspend, wakeup 0 [ 613.309966] hub 3-1:1.0: hub_suspend [ 613.329914] usb 3-1: usb auto-suspend, wakeup 1 [ 613.353823] hub 3-0:1.0: hub_suspend [ 613.353870] usb usb3: bus auto-suspend, wakeup 1 [ 617.249838] usb 1-4: usb auto-suspend, wakeup 1 [ 619.261677] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 619.286438] hub 4-1:1.0: hub_suspend [ 619.295844] usb 4-1: usb auto-suspend, wakeup 1 [ 619.313972] hub 4-0:1.0: hub_suspend [ 619.314016] usb usb4: bus auto-suspend, wakeup 1 [ 619.314313] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 619.766419] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 619.766441] usb usb4: usb wakeup-resume [ 619.766449] usb usb4: usb auto-resume [ 619.766469] hub 4-0:1.0: hub_resume [ 619.766491] usb usb3: usb wakeup-resume [ 619.766497] usb usb3: usb auto-resume [ 619.766516] hub 3-0:1.0: hub_resume [ 619.766567] usb usb3-port1: status 0507 change 0000 [ 619.766605] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 619.766619] hub 3-0:1.0: hub_suspend [ 619.766640] usb usb3: bus auto-suspend, wakeup 1 [ 619.767793] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 619.767811] hub 4-1:1.0: state 8 ports 4 chg 0000 evt 0000 [ 619.793895] usb usb4-port1: status 0203 change 0000 [ 619.817762] usb 4-1: Waited 0ms for CONNECT [ 619.817790] usb 4-1: finish resume [ 619.818785] hub 4-1:1.0: hub_resume [ 619.818884] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 619.846531] usb 4-1-port2: status 0203 change 0000 [ 619.866095] r8152-cfgselector 4-1.2: usb wakeup-resume [ 619.885752] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 619.885777] r8152-cfgselector 4-1.2: finish resume [ 619.889136] usb 4-1-port2: resume, status 0 [ 619.889178] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 626.186639] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 626.208436] hub 4-1:1.0: hub_suspend [ 626.213717] usb 4-1: usb auto-suspend, wakeup 1 [ 626.233856] hub 4-0:1.0: hub_suspend [ 626.233869] usb usb4: bus auto-suspend, wakeup 1 [ 626.234121] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 629.974793] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 629.974823] usb usb4: usb auto-resume [ 629.974854] hub 4-0:1.0: hub_resume [ 629.974899] usb usb3: usb wakeup-resume [ 629.974910] usb usb3: usb auto-resume [ 629.974934] hub 3-0:1.0: hub_resume [ 629.974990] usb usb3-port1: status 0507 change 0000 [ 629.975048] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 629.975074] hub 3-0:1.0: hub_suspend [ 629.975113] usb usb3: bus auto-suspend, wakeup 1 [ 629.976218] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 629.976279] hub 4-1:1.0: state 8 ports 4 chg 0000 evt 0000 [ 630.001862] usb usb4-port1: status 0203 change 0000 [ 630.021803] usb 4-1: Waited 0ms for CONNECT [ 630.021824] usb 4-1: finish resume [ 630.023653] hub 4-1:1.0: hub_resume [ 630.023791] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 630.050363] usb 4-1-port2: status 0203 change 0000 [ 630.069819] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 630.069839] r8152-cfgselector 4-1.2: finish resume [ 630.071024] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 632.540017] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 632.560075] hub 4-1:1.0: hub_suspend [ 632.565542] usb 4-1: usb auto-suspend, wakeup 1 [ 632.585575] hub 4-0:1.0: hub_suspend [ 632.585585] usb usb4: bus auto-suspend, wakeup 1 [ 632.585835] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 632.761741] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 632.761760] usb usb4: usb auto-resume [ 632.761785] hub 4-0:1.0: hub_resume [ 632.789659] usb usb4-port1: status 0263 change 0000 [ 632.789746] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 632.791416] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 632.791459] usb 4-1: usb auto-resume [ 632.857616] usb 4-1: Waited 0ms for CONNECT [ 632.857630] usb 4-1: finish resume [ 632.859520] hub 4-1:1.0: hub_resume [ 632.887477] usb 4-1-port2: status 0263 change 0000 [ 632.889164] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 632.890311] r8152-cfgselector 4-1.2: usb auto-resume [ 632.903396] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 632.957624] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 632.957639] r8152-cfgselector 4-1.2: finish resume [ 632.958336] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 637.586911] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 637.608185] hub 4-1:1.0: hub_suspend [ 637.613597] usb 4-1: usb auto-suspend, wakeup 1 [ 637.633791] hub 4-0:1.0: hub_suspend [ 637.633821] usb usb4: bus auto-suspend, wakeup 1 [ 637.634095] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 653.089535] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 653.089534] usb usb4: usb wakeup-resume [ 653.089544] usb usb4: usb auto-resume [ 653.089564] hub 4-0:1.0: hub_resume [ 653.089746] usb usb3: usb wakeup-resume [ 653.089748] usb usb3: usb auto-resume [ 653.089775] hub 3-0:1.0: hub_resume [ 653.089785] usb usb3-port1: status 0507 change 0000 [ 653.089804] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 653.089815] hub 3-0:1.0: hub_suspend [ 653.089821] usb usb3: bus auto-suspend, wakeup 1 [ 653.090868] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 653.090876] hub 4-1:1.0: state 8 ports 4 chg 0000 evt 0000 [ 653.117566] usb usb4-port1: status 0203 change 0000 [ 653.137548] usb 4-1: Waited 0ms for CONNECT [ 653.137563] usb 4-1: finish resume [ 653.138513] hub 4-1:1.0: hub_resume [ 653.138556] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 653.166195] usb 4-1-port2: status 0203 change 0000 [ 653.185478] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 653.185500] r8152-cfgselector 4-1.2: finish resume [ 653.185982] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 653.189477] NOHZ tick-stop error: local softirq work is pending, handler #08!!! [ 657.713422] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 657.736159] hub 4-1:1.0: hub_suspend [ 657.741521] usb 4-1: usb auto-suspend, wakeup 1 [ 657.765511] hub 4-0:1.0: hub_suspend [ 657.765555] usb usb4: bus auto-suspend, wakeup 1 [ 657.765839] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 658.777596] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 658.777633] usb usb4: usb auto-resume [ 658.777667] hub 4-0:1.0: hub_resume [ 658.805497] usb usb4-port1: status 0263 change 0000 [ 658.805602] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 658.807276] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 658.807351] usb 4-1: usb auto-resume [ 658.873438] usb 4-1: Waited 0ms for CONNECT [ 658.873474] usb 4-1: finish resume [ 658.875288] hub 4-1:1.0: hub_resume [ 658.875430] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 658.907152] usb 4-1-port2: status 0263 change 0000 [ 658.908852] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 658.909975] r8152-cfgselector 4-1.2: usb auto-resume [ 658.951302] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 658.977548] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 658.977568] r8152-cfgselector 4-1.2: finish resume [ 662.153131] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 662.175883] hub 4-1:1.0: hub_suspend [ 662.181467] usb 4-1: usb auto-suspend, wakeup 1 [ 662.205566] hub 4-0:1.0: hub_suspend [ 662.205595] usb usb4: bus auto-suspend, wakeup 1 [ 662.205861] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 664.917410] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 664.917439] usb usb4: usb auto-resume [ 664.917470] hub 4-0:1.0: hub_resume [ 664.945579] usb usb4-port1: status 0263 change 0000 [ 664.945733] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 664.947348] usb 4-1: usb auto-resume [ 664.948296] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 665.017273] usb 4-1: Waited 0ms for CONNECT [ 665.017287] usb 4-1: finish resume [ 665.019215] hub 4-1:1.0: hub_resume [ 665.047080] usb 4-1-port2: status 0263 change 0000 [ 665.048678] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 665.049988] r8152-cfgselector 4-1.2: usb auto-resume [ 665.064123] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 665.121298] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 665.121307] r8152-cfgselector 4-1.2: finish resume [ 665.125279] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 667.479513] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 667.501376] hub 4-1:1.0: hub_suspend [ 667.509279] usb 4-1: usb auto-suspend, wakeup 1 [ 667.529302] hub 4-0:1.0: hub_suspend [ 667.529317] usb usb4: bus auto-suspend, wakeup 1 [ 667.529578] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 675.163873] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 675.163913] usb usb4: usb auto-resume [ 675.163950] hub 4-0:1.0: hub_resume [ 675.189616] usb usb4-port1: status 0263 change 0000 [ 675.189675] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 675.191256] usb 4-1: usb auto-resume [ 675.191268] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 675.257264] usb 4-1: Waited 0ms for CONNECT [ 675.257289] usb 4-1: finish resume [ 675.259411] hub 4-1:1.0: hub_resume [ 675.259478] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 675.287338] usb 4-1-port2: status 0263 change 0000 [ 675.288599] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 675.289789] r8152-cfgselector 4-1.2: usb auto-resume [ 675.305856] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 675.357159] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 675.357167] r8152-cfgselector 4-1.2: finish resume [ 675.357889] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 692.731971] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 692.751693] hub 4-1:1.0: hub_suspend [ 692.757111] usb 4-1: usb auto-suspend, wakeup 1 [ 692.781399] hub 4-0:1.0: hub_suspend [ 692.781438] usb usb4: bus auto-suspend, wakeup 1 [ 692.781728] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 694.357165] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 694.357208] usb usb4: usb auto-resume [ 694.357246] hub 4-0:1.0: hub_resume [ 694.389205] usb usb4-port1: status 0263 change 0000 [ 694.389444] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 694.391023] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 694.391152] usb 4-1: usb auto-resume [ 694.457654] usb 4-1: Waited 0ms for CONNECT [ 694.457679] usb 4-1: finish resume [ 694.464617] hub 4-1:1.0: hub_resume [ 694.490370] usb 4-1-port2: status 0263 change 0000 [ 694.491651] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 694.492809] r8152-cfgselector 4-1.2: usb auto-resume [ 694.517862] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 694.557291] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 694.557314] r8152-cfgselector 4-1.2: finish resume [ 694.558120] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 707.283719] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 707.304034] hub 4-1:1.0: hub_suspend [ 707.313077] usb 4-1: usb auto-suspend, wakeup 1 [ 707.337350] hub 4-0:1.0: hub_suspend [ 707.337404] usb usb4: bus auto-suspend, wakeup 1 [ 707.337698] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 707.673179] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 707.673208] usb usb4: usb auto-resume [ 707.673238] hub 4-0:1.0: hub_resume [ 707.701241] usb usb4-port1: status 0263 change 0000 [ 707.701344] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 707.703143] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 707.703199] usb 4-1: usb auto-resume [ 707.769327] usb 4-1: Waited 0ms for CONNECT [ 707.769349] usb 4-1: finish resume [ 707.771884] hub 4-1:1.0: hub_resume [ 707.799081] usb 4-1-port2: status 0263 change 0000 [ 707.800655] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 707.801771] r8152-cfgselector 4-1.2: usb auto-resume [ 707.829831] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 707.869141] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 707.869165] r8152-cfgselector 4-1.2: finish resume [ 707.870405] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 711.330727] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 711.351645] hub 4-1:1.0: hub_suspend [ 711.356896] usb 4-1: usb auto-suspend, wakeup 1 [ 711.380995] hub 4-0:1.0: hub_suspend [ 711.381013] usb usb4: bus auto-suspend, wakeup 1 [ 711.381272] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 714.966018] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 714.966046] usb usb4: usb auto-resume [ 714.966076] hub 4-0:1.0: hub_resume [ 714.966122] usb usb3: usb wakeup-resume [ 714.966133] usb usb3: usb auto-resume [ 714.966157] hub 3-0:1.0: hub_resume [ 714.966208] usb usb3-port1: status 0507 change 0000 [ 714.966263] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 714.966289] hub 3-0:1.0: hub_suspend [ 714.966321] usb usb3: bus auto-suspend, wakeup 1 [ 714.967678] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 714.967728] hub 4-1:1.0: state 8 ports 4 chg 0000 evt 0000 [ 714.993172] usb usb4-port1: status 0203 change 0000 [ 715.013103] usb 4-1: Waited 0ms for CONNECT [ 715.013125] usb 4-1: finish resume [ 715.014491] hub 4-1:1.0: hub_resume [ 715.014575] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 715.042297] usb 4-1-port2: status 0203 change 0000 [ 715.061155] r8152-cfgselector 4-1.2: usb wakeup-resume [ 715.081146] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 715.081175] r8152-cfgselector 4-1.2: finish resume [ 715.084249] usb 4-1-port2: resume, status 0 [ 715.084283] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 717.589304] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 717.611791] hub 4-1:1.0: hub_suspend [ 717.616995] usb 4-1: usb auto-suspend, wakeup 1 [ 717.637098] hub 4-0:1.0: hub_suspend [ 717.637158] usb usb4: bus auto-suspend, wakeup 1 [ 717.637464] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 718.169080] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 718.169111] usb usb4: usb auto-resume [ 718.169141] hub 4-0:1.0: hub_resume [ 718.197146] usb usb4-port1: status 0263 change 0000 [ 718.197269] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 718.198743] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 718.198752] usb 4-1: usb auto-resume [ 718.264962] usb 4-1: Waited 0ms for CONNECT [ 718.264983] usb 4-1: finish resume [ 718.267161] hub 4-1:1.0: hub_resume [ 718.294283] usb 4-1-port2: status 0263 change 0000 [ 718.295538] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 718.296723] r8152-cfgselector 4-1.2: usb auto-resume [ 718.313408] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 718.360965] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 718.360988] r8152-cfgselector 4-1.2: finish resume [ 718.362307] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 731.055473] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 731.055576] usb usb1-port2: status 0100, change 0001, 12 Mb/s [ 731.055598] usb 1-2: USB disconnect, device number 11 [ 731.055609] usb 1-2: unregistering device [ 731.055617] usb 1-2: unregistering interface 1-2:1.0 [ 731.055875] xhci_hcd 0000:00:14.0: shutdown urb 0000000018b2793e ep1in-intr [ 731.108959] usb 1-2: usb_disable_device nuking all URBs [ 731.260910] usb usb1-port2: debounce total 100ms stable 100ms status 0x100 [ 731.260957] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 731.378519] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 731.378625] usb usb1-port2: status 0301, change 0001, 1.5 Mb/s [ 731.560832] usb usb1-port2: debounce total 125ms stable 100ms status 0x100 [ 731.561083] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 732.065730] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004 [ 732.065859] usb usb1-port2: status 0301, change 0001, 1.5 Mb/s [ 732.209022] usb usb1-port2: debounce total 100ms stable 100ms status 0x301 [ 732.336986] usb 1-2: new low-speed USB device number 12 using xhci_hcd [ 732.487262] usb 1-2: skipped 1 descriptor after interface [ 732.487769] usb 1-2: default language 0x0409 [ 732.489223] usb 1-2: udev 12, busnum 1, minor = 11 [ 732.489245] usb 1-2: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00 [ 732.489261] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 732.489270] usb 1-2: Product: USB Optical Mouse [ 732.489279] usb 1-2: Manufacturer: Logitech [ 732.490276] usb 1-2: usb_probe_device [ 732.490291] usb 1-2: configuration #1 chosen from 1 choice [ 732.493283] usb 1-2: adding 1-2:1.0 (config #1, interface 0) [ 732.493911] usbhid 1-2:1.0: usb_probe_interface [ 732.493923] usbhid 1-2:1.0: usb_probe_interface - got id [ 732.496334] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/0003:046D:C077.000C/input/input41 [ 732.496908] hid-generic 0003:046D:C077.000C: input,hidraw5: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:14.0-2/input0 [ 784.788141] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 784.807950] hub 4-1:1.0: hub_suspend [ 784.816486] usb 4-1: usb auto-suspend, wakeup 1 [ 784.840456] hub 4-0:1.0: hub_suspend [ 784.840518] usb usb4: bus auto-suspend, wakeup 1 [ 784.840829] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 785.621207] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 785.621236] usb usb4: usb auto-resume [ 785.621265] hub 4-0:1.0: hub_resume [ 785.621313] usb usb3: usb wakeup-resume [ 785.621325] usb usb3: usb auto-resume [ 785.621349] hub 3-0:1.0: hub_resume [ 785.621403] usb usb3-port1: status 0507 change 0000 [ 785.621463] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 785.621489] hub 3-0:1.0: hub_suspend [ 785.621527] usb usb3: bus auto-suspend, wakeup 1 [ 785.623691] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 785.623732] hub 4-1:1.0: state 8 ports 4 chg 0000 evt 0000 [ 785.648576] usb usb4-port1: status 0203 change 0000 [ 785.668365] usb 4-1: Waited 0ms for CONNECT [ 785.668381] usb 4-1: finish resume [ 785.669188] hub 4-1:1.0: hub_resume [ 785.669272] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 785.697069] usb 4-1-port2: status 0203 change 0000 [ 785.716517] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 785.716534] r8152-cfgselector 4-1.2: finish resume [ 785.717206] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 819.106722] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 819.126720] hub 4-1:1.0: hub_suspend [ 819.132193] usb 4-1: usb auto-suspend, wakeup 1 [ 819.152325] hub 4-0:1.0: hub_suspend [ 819.152352] usb usb4: bus auto-suspend, wakeup 1 [ 819.152618] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 819.540118] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 819.540133] usb usb4: usb auto-resume [ 819.540152] hub 4-0:1.0: hub_resume [ 819.568276] usb usb4-port1: status 0263 change 0000 [ 819.568423] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 819.569902] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 819.569961] usb 4-1: usb auto-resume [ 819.636212] usb 4-1: Waited 0ms for CONNECT [ 819.636234] usb 4-1: finish resume [ 819.638552] hub 4-1:1.0: hub_resume [ 819.665613] usb 4-1-port2: status 0263 change 0000 [ 819.666989] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 819.670083] r8152-cfgselector 4-1.2: usb auto-resume [ 819.685016] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 819.736326] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 819.736349] r8152-cfgselector 4-1.2: finish resume [ 819.737054] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 826.330771] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 826.350464] hub 4-1:1.0: hub_suspend [ 826.356130] usb 4-1: usb auto-suspend, wakeup 1 [ 826.376288] hub 4-0:1.0: hub_suspend [ 826.376316] usb usb4: bus auto-suspend, wakeup 1 [ 826.376587] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 826.964161] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 826.964200] usb usb4: usb auto-resume [ 826.964236] hub 4-0:1.0: hub_resume [ 826.992202] usb usb4-port1: status 0263 change 0000 [ 826.992329] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 826.994055] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 826.994118] usb 4-1: usb auto-resume [ 827.060286] usb 4-1: Waited 0ms for CONNECT [ 827.060308] usb 4-1: finish resume [ 827.062881] hub 4-1:1.0: hub_resume [ 827.089465] usb 4-1-port2: status 0263 change 0000 [ 827.090723] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 827.091877] r8152-cfgselector 4-1.2: usb auto-resume [ 827.124766] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 827.156096] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 827.156127] r8152-cfgselector 4-1.2: finish resume [ 836.529318] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 836.552047] hub 4-1:1.0: hub_suspend [ 836.560239] usb 4-1: usb auto-suspend, wakeup 1 [ 836.580328] hub 4-0:1.0: hub_suspend [ 836.580370] usb usb4: bus auto-suspend, wakeup 1 [ 836.580659] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 837.460244] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 837.460273] usb usb4: usb auto-resume [ 837.460303] hub 4-0:1.0: hub_resume [ 837.488016] usb usb4-port1: status 0263 change 0000 [ 837.488052] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 837.489456] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 837.489465] usb 4-1: usb auto-resume [ 837.556049] usb 4-1: Waited 0ms for CONNECT [ 837.556059] usb 4-1: finish resume [ 837.557996] hub 4-1:1.0: hub_resume [ 837.589074] usb 4-1-port2: status 0263 change 0000 [ 837.590341] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 837.591501] r8152-cfgselector 4-1.2: usb auto-resume [ 837.604610] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 837.656094] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 837.656105] r8152-cfgselector 4-1.2: finish resume [ 837.656834] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 844.849904] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 844.870241] hub 4-1:1.0: hub_suspend [ 844.875898] usb 4-1: usb auto-suspend, wakeup 1 [ 844.895951] hub 4-0:1.0: hub_suspend [ 844.895960] usb usb4: bus auto-suspend, wakeup 1 [ 844.896208] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 845.987896] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 845.987906] usb usb4: usb auto-resume [ 845.987923] hub 4-0:1.0: hub_resume [ 846.015956] usb usb4-port1: status 0263 change 0000 [ 846.016255] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 846.017770] usb 4-1: usb auto-resume [ 846.019377] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 846.091877] usb 4-1: Waited 0ms for CONNECT [ 846.091883] usb 4-1: finish resume [ 846.097160] hub 4-1:1.0: hub_resume [ 846.097184] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 846.125088] usb 4-1-port2: status 0263 change 0000 [ 846.126350] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 846.127539] r8152-cfgselector 4-1.2: usb auto-resume [ 846.151319] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 846.195978] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 846.196015] r8152-cfgselector 4-1.2: finish resume [ 846.198710] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 888.470365] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 888.490121] hub 4-1:1.0: hub_suspend [ 888.495809] usb 4-1: usb auto-suspend, wakeup 1 [ 888.515852] hub 4-0:1.0: hub_suspend [ 888.515871] usb usb4: bus auto-suspend, wakeup 1 [ 888.516131] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 890.195781] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 890.195824] usb usb4: usb auto-resume [ 890.195859] hub 4-0:1.0: hub_resume [ 890.223874] usb usb4-port1: status 0263 change 0000 [ 890.223976] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 890.225645] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 890.225700] usb 4-1: usb auto-resume [ 890.295728] usb 4-1: Waited 0ms for CONNECT [ 890.295750] usb 4-1: finish resume [ 890.297653] hub 4-1:1.0: hub_resume [ 890.324956] usb 4-1-port2: status 0263 change 0000 [ 890.326286] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 890.327361] r8152-cfgselector 4-1.2: usb auto-resume [ 890.340698] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 890.399853] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 890.399876] r8152-cfgselector 4-1.2: finish resume [ 890.401231] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 892.455561] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 892.478699] hub 4-1:1.0: hub_suspend [ 892.487633] usb 4-1: usb auto-suspend, wakeup 1 [ 892.507899] hub 4-0:1.0: hub_suspend [ 892.507972] usb usb4: bus auto-suspend, wakeup 1 [ 892.508281] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 894.164461] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 894.164499] usb usb4: usb auto-resume [ 894.164551] hub 4-0:1.0: hub_resume [ 894.164613] usb usb3: usb wakeup-resume [ 894.164628] usb usb3: usb auto-resume [ 894.164656] hub 3-0:1.0: hub_resume [ 894.164726] usb usb3-port1: status 0507 change 0000 [ 894.164808] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 894.164841] hub 3-0:1.0: hub_suspend [ 894.164893] usb usb3: bus auto-suspend, wakeup 1 [ 894.165929] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 894.165975] hub 4-1:1.0: state 8 ports 4 chg 0000 evt 0000 [ 894.191746] usb usb4-port1: status 0203 change 0000 [ 894.211726] usb 4-1: Waited 0ms for CONNECT [ 894.211738] usb 4-1: finish resume [ 894.212516] hub 4-1:1.0: hub_resume [ 894.212862] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 894.240216] usb 4-1-port2: status 0203 change 0000 [ 894.259736] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 894.259749] r8152-cfgselector 4-1.2: finish resume [ 894.260834] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 896.767286] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 896.790643] hub 4-1:1.0: hub_suspend [ 896.799708] usb 4-1: usb auto-suspend, wakeup 1 [ 896.819722] hub 4-0:1.0: hub_suspend [ 896.819782] usb usb4: bus auto-suspend, wakeup 1 [ 896.820084] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 899.503637] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 899.503685] usb usb4: usb auto-resume [ 899.503713] hub 4-0:1.0: hub_resume [ 899.535558] usb usb4-port1: status 0263 change 0000 [ 899.535651] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 899.537255] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 899.537276] usb 4-1: usb auto-resume [ 899.603504] usb 4-1: Waited 0ms for CONNECT [ 899.603509] usb 4-1: finish resume [ 899.605154] hub 4-1:1.0: hub_resume [ 899.632802] usb 4-1-port2: status 0263 change 0000 [ 899.634019] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 899.635217] r8152-cfgselector 4-1.2: usb auto-resume [ 899.660370] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 899.699532] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 899.699538] r8152-cfgselector 4-1.2: finish resume [ 899.700067] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 935.757276] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 935.778020] hub 4-1:1.0: hub_suspend [ 935.783299] usb 4-1: usb auto-suspend, wakeup 1 [ 935.803518] hub 4-0:1.0: hub_suspend [ 935.803563] usb usb4: bus auto-suspend, wakeup 1 [ 935.803864] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 936.031352] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 936.031368] usb usb4: usb auto-resume [ 936.031386] hub 4-0:1.0: hub_resume [ 936.059409] usb usb4-port1: status 0263 change 0000 [ 936.059449] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 936.060894] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 936.060902] usb 4-1: usb auto-resume [ 936.127267] usb 4-1: Waited 0ms for CONNECT [ 936.127273] usb 4-1: finish resume [ 936.129040] hub 4-1:1.0: hub_resume [ 936.129114] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 936.157067] usb 4-1-port2: status 0263 change 0000 [ 936.158312] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 936.159380] r8152-cfgselector 4-1.2: usb auto-resume [ 936.192637] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 936.235327] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 936.235341] r8152-cfgselector 4-1.2: finish resume [ 936.236069] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 938.743014] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 938.766850] hub 4-1:1.0: hub_suspend [ 938.775359] usb 4-1: usb auto-suspend, wakeup 1 [ 938.799517] hub 4-0:1.0: hub_suspend [ 938.799562] usb usb4: bus auto-suspend, wakeup 1 [ 938.799874] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 942.292262] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 942.292297] usb usb4: usb auto-resume [ 942.292331] hub 4-0:1.0: hub_resume [ 942.292375] usb usb3: usb wakeup-resume [ 942.292386] usb usb3: usb auto-resume [ 942.292411] hub 3-0:1.0: hub_resume [ 942.292461] usb usb3-port1: status 0507 change 0000 [ 942.292518] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 942.292545] hub 3-0:1.0: hub_suspend [ 942.292578] usb usb3: bus auto-suspend, wakeup 1 [ 942.293901] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 942.293950] hub 4-1:1.0: state 8 ports 4 chg 0000 evt 0000 [ 942.319869] usb usb4-port1: status 0203 change 0000 [ 942.339529] usb 4-1: Waited 0ms for CONNECT [ 942.339548] usb 4-1: finish resume [ 942.340482] hub 4-1:1.0: hub_resume [ 942.343374] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 942.367901] usb 4-1-port2: status 0203 change 0000 [ 942.387360] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 942.387380] r8152-cfgselector 4-1.2: finish resume [ 942.388101] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 949.695892] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 949.724435] hub 4-1:1.0: hub_suspend [ 949.731590] usb 4-1: usb auto-suspend, wakeup 1 [ 949.751387] hub 4-0:1.0: hub_suspend [ 949.751422] usb usb4: bus auto-suspend, wakeup 1 [ 949.751703] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 952.227320] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 952.227346] usb usb4: usb auto-resume [ 952.227373] hub 4-0:1.0: hub_resume [ 952.259383] usb usb4-port1: status 0263 change 0000 [ 952.259422] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 952.261045] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 952.261066] usb 4-1: usb auto-resume [ 952.331292] usb 4-1: Waited 0ms for CONNECT [ 952.331317] usb 4-1: finish resume [ 952.333299] hub 4-1:1.0: hub_resume [ 952.360630] usb 4-1-port2: status 0263 change 0000 [ 952.362018] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 952.363373] r8152-cfgselector 4-1.2: usb auto-resume [ 952.403662] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 952.435346] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 952.435357] r8152-cfgselector 4-1.2: finish resume [ 956.868932] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 956.889668] hub 4-1:1.0: hub_suspend [ 956.895344] usb 4-1: usb auto-suspend, wakeup 1 [ 956.915409] hub 4-0:1.0: hub_suspend [ 956.915436] usb usb4: bus auto-suspend, wakeup 1 [ 956.915701] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 959.486660] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 959.486693] usb usb4: usb auto-resume [ 959.486726] hub 4-0:1.0: hub_resume [ 959.486775] usb usb3: usb wakeup-resume [ 959.486788] usb usb3: usb auto-resume [ 959.486814] hub 3-0:1.0: hub_resume [ 959.486878] usb usb3-port1: status 0507 change 0000 [ 959.486947] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 959.486977] hub 3-0:1.0: hub_suspend [ 959.487018] usb usb3: bus auto-suspend, wakeup 1 [ 959.491197] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 959.491255] hub 4-1:1.0: state 8 ports 4 chg 0000 evt 0000 [ 959.515212] usb usb4-port1: status 0203 change 0000 [ 959.535372] usb 4-1: Waited 0ms for CONNECT [ 959.535397] usb 4-1: finish resume [ 959.536482] hub 4-1:1.0: hub_resume [ 959.536568] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 959.563797] usb 4-1-port2: status 0203 change 0000 [ 959.583160] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 959.583173] r8152-cfgselector 4-1.2: finish resume [ 959.583920] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 978.580474] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 978.601359] hub 4-1:1.0: hub_suspend [ 978.607155] usb 4-1: usb auto-suspend, wakeup 1 [ 978.627152] hub 4-0:1.0: hub_suspend [ 978.627162] usb usb4: bus auto-suspend, wakeup 1 [ 978.627411] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 980.179804] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 980.179836] usb usb4: usb auto-resume [ 980.179875] hub 4-0:1.0: hub_resume [ 980.179925] usb usb3: usb wakeup-resume [ 980.179937] usb usb3: usb auto-resume [ 980.179963] hub 3-0:1.0: hub_resume [ 980.180018] usb usb3-port1: status 0507 change 0000 [ 980.180092] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 980.180121] hub 3-0:1.0: hub_suspend [ 980.180166] usb usb3: bus auto-suspend, wakeup 1 [ 980.181308] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 980.181347] hub 4-1:1.0: state 8 ports 4 chg 0000 evt 0000 [ 980.207138] usb usb4-port1: status 0203 change 0000 [ 980.227231] usb 4-1: Waited 0ms for CONNECT [ 980.227251] usb 4-1: finish resume [ 980.228281] hub 4-1:1.0: hub_resume [ 980.228422] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 980.255619] usb 4-1-port2: status 0203 change 0000 [ 980.275129] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 980.275155] r8152-cfgselector 4-1.2: finish resume [ 980.276371] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 988.588299] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 988.610063] hub 4-1:1.0: hub_suspend [ 988.619039] usb 4-1: usb auto-suspend, wakeup 1 [ 988.639194] hub 4-0:1.0: hub_suspend [ 988.639213] usb usb4: bus auto-suspend, wakeup 1 [ 988.639473] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 989.443070] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 989.443099] usb usb4: usb auto-resume [ 989.443129] hub 4-0:1.0: hub_resume [ 989.471247] usb usb4-port1: status 0263 change 0000 [ 989.471406] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 989.472958] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 989.473080] usb 4-1: usb auto-resume [ 989.539095] usb 4-1: Waited 0ms for CONNECT [ 989.539117] usb 4-1: finish resume [ 989.541798] hub 4-1:1.0: hub_resume [ 989.568512] usb 4-1-port2: status 0263 change 0000 [ 989.570263] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 989.571644] r8152-cfgselector 4-1.2: usb auto-resume [ 989.617846] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 989.639054] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 989.639093] r8152-cfgselector 4-1.2: finish resume [ 996.913925] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 996.938451] hub 4-1:1.0: hub_suspend [ 996.946947] usb 4-1: usb auto-suspend, wakeup 1 [ 996.967061] hub 4-0:1.0: hub_suspend [ 996.967088] usb usb4: bus auto-suspend, wakeup 1 [ 996.967358] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 999.991007] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 999.991026] usb usb4: usb auto-resume [ 999.991049] hub 4-0:1.0: hub_resume [ 1000.023785] usb usb4-port1: status 0263 change 0000 [ 1000.023931] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1000.025548] usb 4-1: usb auto-resume [ 1000.025553] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 1000.091009] usb 4-1: Waited 0ms for CONNECT [ 1000.091026] usb 4-1: finish resume [ 1000.093252] hub 4-1:1.0: hub_resume [ 1000.120333] usb 4-1-port2: status 0263 change 0000 [ 1000.121617] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1000.122788] r8152-cfgselector 4-1.2: usb auto-resume [ 1000.137714] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 1000.190968] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1000.190993] r8152-cfgselector 4-1.2: finish resume [ 1000.191943] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1011.273831] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 1011.297241] hub 4-1:1.0: hub_suspend [ 1011.302932] usb 4-1: usb auto-suspend, wakeup 1 [ 1011.322859] hub 4-0:1.0: hub_suspend [ 1011.322877] usb usb4: bus auto-suspend, wakeup 1 [ 1011.323142] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 1011.938806] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 1011.938824] usb usb4: usb auto-resume [ 1011.938849] hub 4-0:1.0: hub_resume [ 1011.970813] usb usb4-port1: status 0263 change 0000 [ 1011.970907] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1011.972332] usb 4-1: usb auto-resume [ 1011.972492] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 1012.042828] usb 4-1: Waited 0ms for CONNECT [ 1012.042852] usb 4-1: finish resume [ 1012.044859] hub 4-1:1.0: hub_resume [ 1012.044924] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1012.075890] usb 4-1-port2: status 0263 change 0000 [ 1012.077165] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1012.078316] r8152-cfgselector 4-1.2: usb auto-resume [ 1012.143010] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1012.143030] r8152-cfgselector 4-1.2: finish resume [ 1038.671870] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 1038.693091] hub 4-1:1.0: hub_suspend [ 1038.698784] usb 4-1: usb auto-suspend, wakeup 1 [ 1038.718878] hub 4-0:1.0: hub_suspend [ 1038.718922] usb usb4: bus auto-suspend, wakeup 1 [ 1038.719210] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 1042.218735] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 1042.218761] usb usb4: usb auto-resume [ 1042.218788] hub 4-0:1.0: hub_resume [ 1042.246746] usb usb4-port1: status 0263 change 0000 [ 1042.246890] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1042.248557] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 1042.248580] usb 4-1: usb auto-resume [ 1042.314739] usb 4-1: Waited 0ms for CONNECT [ 1042.314758] usb 4-1: finish resume [ 1042.316934] hub 4-1:1.0: hub_resume [ 1042.344065] usb 4-1-port2: status 0263 change 0000 [ 1042.345381] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1042.346606] r8152-cfgselector 4-1.2: usb auto-resume [ 1042.363417] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 1042.414692] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1042.414712] r8152-cfgselector 4-1.2: finish resume [ 1042.415401] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1047.319323] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 1047.341155] hub 4-1:1.0: hub_suspend [ 1047.346737] usb 4-1: usb auto-suspend, wakeup 1 [ 1047.366810] hub 4-0:1.0: hub_suspend [ 1047.366821] usb usb4: bus auto-suspend, wakeup 1 [ 1047.367070] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 1053.395943] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 1053.395979] usb usb4: usb auto-resume [ 1053.396011] hub 4-0:1.0: hub_resume [ 1053.396102] usb usb3: usb wakeup-resume [ 1053.396116] usb usb3: usb auto-resume [ 1053.396143] hub 3-0:1.0: hub_resume [ 1053.396531] usb usb3-port1: status 0507 change 0000 [ 1053.396627] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1053.396774] hub 3-0:1.0: hub_suspend [ 1053.396818] usb usb3: bus auto-suspend, wakeup 1 [ 1053.397332] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1053.397367] hub 4-1:1.0: state 8 ports 4 chg 0000 evt 0000 [ 1053.423108] usb usb4-port1: status 0203 change 0000 [ 1053.442581] usb 4-1: Waited 0ms for CONNECT [ 1053.442606] usb 4-1: finish resume [ 1053.443481] hub 4-1:1.0: hub_resume [ 1053.443589] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1053.471484] usb 4-1-port2: status 0203 change 0000 [ 1053.490765] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1053.490793] r8152-cfgselector 4-1.2: finish resume [ 1053.491620] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1055.993710] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 1056.012849] hub 4-1:1.0: hub_suspend [ 1056.018500] usb 4-1: usb auto-suspend, wakeup 1 [ 1056.038565] hub 4-0:1.0: hub_suspend [ 1056.038574] usb usb4: bus auto-suspend, wakeup 1 [ 1056.038823] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 1056.382583] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 1056.382593] usb usb4: usb auto-resume [ 1056.382612] hub 4-0:1.0: hub_resume [ 1056.410887] usb usb4-port1: status 0263 change 0000 [ 1056.411027] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1056.412591] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 1056.412700] usb 4-1: usb auto-resume [ 1056.478728] usb 4-1: Waited 0ms for CONNECT [ 1056.478750] usb 4-1: finish resume [ 1056.480514] hub 4-1:1.0: hub_resume [ 1056.508357] usb 4-1-port2: status 0263 change 0000 [ 1056.510085] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1056.511167] r8152-cfgselector 4-1.2: usb auto-resume [ 1056.559030] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 1056.578721] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1056.578744] r8152-cfgselector 4-1.2: finish resume [ 1157.680224] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 1157.700611] hub 4-1:1.0: hub_suspend [ 1157.705930] usb 4-1: usb auto-suspend, wakeup 1 [ 1157.726011] hub 4-0:1.0: hub_suspend [ 1157.726047] usb usb4: bus auto-suspend, wakeup 1 [ 1157.726328] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 1157.969902] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 1157.969910] usb usb4: usb auto-resume [ 1157.969927] hub 4-0:1.0: hub_resume [ 1157.997895] usb usb4-port1: status 0263 change 0000 [ 1157.997924] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1157.999300] usb 4-1: usb auto-resume [ 1158.001839] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 1158.076042] usb 4-1: Waited 0ms for CONNECT [ 1158.076049] usb 4-1: finish resume [ 1158.078636] hub 4-1:1.0: hub_resume [ 1158.078689] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1158.106998] usb 4-1-port2: status 0263 change 0000 [ 1158.108247] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1158.109443] r8152-cfgselector 4-1.2: usb auto-resume [ 1158.146652] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 1158.181839] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1158.181846] r8152-cfgselector 4-1.2: finish resume [ 1193.614650] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 1193.636076] hub 4-1:1.0: hub_suspend [ 1193.641620] usb 4-1: usb auto-suspend, wakeup 1 [ 1193.661662] hub 4-0:1.0: hub_suspend [ 1193.661671] usb usb4: bus auto-suspend, wakeup 1 [ 1193.661920] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 1194.065650] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 1194.065665] usb usb4: usb auto-resume [ 1194.065684] hub 4-0:1.0: hub_resume [ 1194.093722] usb usb4-port1: status 0263 change 0000 [ 1194.093756] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1194.095078] usb 4-1: usb auto-resume [ 1194.095080] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 1194.161786] usb 4-1: Waited 0ms for CONNECT [ 1194.161801] usb 4-1: finish resume [ 1194.164404] hub 4-1:1.0: hub_resume [ 1194.191049] usb 4-1-port2: status 0263 change 0000 [ 1194.192297] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1194.193452] r8152-cfgselector 4-1.2: usb auto-resume [ 1194.257645] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1194.257663] r8152-cfgselector 4-1.2: finish resume [ 1202.210660] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 1202.232386] hub 4-1:1.0: hub_suspend [ 1202.237699] usb 4-1: usb auto-suspend, wakeup 1 [ 1202.261854] hub 4-0:1.0: hub_suspend [ 1202.261867] usb usb4: bus auto-suspend, wakeup 1 [ 1202.262118] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 1203.248060] usb usb4: usb wakeup-resume [ 1203.249305] hub 4-0:1.0: state 8 ports 2 chg 0000 evt 0000 [ 1203.249422] hub 4-1:1.0: state 8 ports 4 chg 0000 evt 0000 [ 1203.369569] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 1203.369581] usb usb4: usb auto-resume [ 1203.369597] hub 4-0:1.0: hub_resume [ 1203.401844] usb usb4-port1: status 0203 change 0000 [ 1203.445761] usb 4-1: Waited 0ms for CONNECT [ 1203.445769] usb 4-1: finish resume [ 1203.446769] hub 4-1:1.0: hub_resume [ 1203.474057] usb 4-1-port2: status 0203 change 0000 [ 1203.497706] r8152-cfgselector 4-1.2: usb wakeup-resume [ 1203.521802] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1203.521841] r8152-cfgselector 4-1.2: finish resume [ 1203.525369] usb 4-1-port2: resume, status 0 [ 1203.525422] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1203.525460] usb usb4-port1: resume, status 0 [ 1203.525508] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1206.934571] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 1206.956139] hub 4-1:1.0: hub_suspend [ 1206.961664] usb 4-1: usb auto-suspend, wakeup 1 [ 1206.981616] hub 4-0:1.0: hub_suspend [ 1206.981626] usb usb4: bus auto-suspend, wakeup 1 [ 1206.981876] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 1209.298049] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 1209.298058] usb usb4: usb auto-resume [ 1209.298075] hub 4-0:1.0: hub_resume [ 1209.298084] usb usb3: usb wakeup-resume [ 1209.298086] usb usb3: usb auto-resume [ 1209.298101] hub 3-0:1.0: hub_resume [ 1209.298114] usb usb3-port1: status 0507 change 0000 [ 1209.298126] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1209.298130] hub 3-0:1.0: hub_suspend [ 1209.298137] usb usb3: bus auto-suspend, wakeup 1 [ 1209.299672] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1209.299683] hub 4-1:1.0: state 8 ports 4 chg 0000 evt 0000 [ 1209.325667] usb usb4-port1: status 0203 change 0000 [ 1209.345539] usb 4-1: Waited 0ms for CONNECT [ 1209.345547] usb 4-1: finish resume [ 1209.346355] hub 4-1:1.0: hub_resume [ 1209.346423] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1209.374395] usb 4-1-port2: status 0203 change 0000 [ 1209.393650] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1209.393670] r8152-cfgselector 4-1.2: finish resume [ 1209.394769] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1234.622964] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 1234.643757] hub 4-1:1.0: hub_suspend [ 1234.649465] usb 4-1: usb auto-suspend, wakeup 1 [ 1234.669499] hub 4-0:1.0: hub_suspend [ 1234.669514] usb usb4: bus auto-suspend, wakeup 1 [ 1234.669768] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 1236.661499] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 1236.661528] usb usb4: usb auto-resume [ 1236.661557] hub 4-0:1.0: hub_resume [ 1236.689529] usb usb4-port1: status 0263 change 0000 [ 1236.689683] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1236.691339] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 1236.691462] usb 4-1: usb auto-resume [ 1236.757472] usb 4-1: Waited 0ms for CONNECT [ 1236.757494] usb 4-1: finish resume [ 1236.759935] hub 4-1:1.0: hub_resume [ 1236.786698] usb 4-1-port2: status 0263 change 0000 [ 1236.787999] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1236.789157] r8152-cfgselector 4-1.2: usb auto-resume [ 1236.809380] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 1236.853421] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1236.853429] r8152-cfgselector 4-1.2: finish resume [ 1236.854143] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1246.698767] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 1246.719957] hub 4-1:1.0: hub_suspend [ 1246.725489] usb 4-1: usb auto-suspend, wakeup 1 [ 1246.745376] hub 4-0:1.0: hub_suspend [ 1246.745397] usb usb4: bus auto-suspend, wakeup 1 [ 1246.745657] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 1247.245543] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 1247.245570] usb usb4: usb auto-resume [ 1247.245598] hub 4-0:1.0: hub_resume [ 1247.273481] usb usb4-port1: status 0263 change 0000 [ 1247.273584] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1247.275371] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 1247.275429] usb 4-1: usb auto-resume [ 1247.341530] usb 4-1: Waited 0ms for CONNECT [ 1247.341554] usb 4-1: finish resume [ 1247.343330] hub 4-1:1.0: hub_resume [ 1247.373441] usb 4-1-port2: status 0263 change 0000 [ 1247.374982] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1247.376592] r8152-cfgselector 4-1.2: usb auto-resume [ 1247.408151] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 1247.441473] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1247.441479] r8152-cfgselector 4-1.2: finish resume [ 1247.442142] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1251.595582] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 1251.616226] hub 4-1:1.0: hub_suspend [ 1251.625502] usb 4-1: usb auto-suspend, wakeup 1 [ 1251.646663] hub 4-0:1.0: hub_suspend [ 1251.646706] usb usb4: bus auto-suspend, wakeup 1 [ 1251.646996] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 1253.053357] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 1253.053394] usb usb4: usb auto-resume [ 1253.053428] hub 4-0:1.0: hub_resume [ 1253.081323] usb usb4-port1: status 0263 change 0000 [ 1253.081383] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1253.083128] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 1253.083163] usb 4-1: usb auto-resume [ 1253.149270] usb 4-1: Waited 0ms for CONNECT [ 1253.149284] usb 4-1: finish resume [ 1253.151217] hub 4-1:1.0: hub_resume [ 1253.182548] usb 4-1-port2: status 0263 change 0000 [ 1253.186992] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1253.188198] r8152-cfgselector 4-1.2: usb auto-resume [ 1253.197877] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 1253.254791] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1253.254814] r8152-cfgselector 4-1.2: finish resume [ 1253.256248] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1259.011200] r8152-cfgselector 4-1.2: usb auto-suspend, wakeup 1 [ 1259.031728] hub 4-1:1.0: hub_suspend [ 1259.037227] usb 4-1: usb auto-suspend, wakeup 1 [ 1259.068572] hub 4-0:1.0: hub_suspend [ 1259.068585] usb usb4: bus auto-suspend, wakeup 1 [ 1259.068848] xhci_hcd 0000:39:00.0: hcd_pci_runtime_suspend: 0 [ 1259.221308] xhci_hcd 0000:39:00.0: hcd_pci_runtime_resume: 0 [ 1259.221332] usb usb4: usb auto-resume [ 1259.221357] hub 4-0:1.0: hub_resume [ 1259.249309] usb usb4-port1: status 0263 change 0000 [ 1259.249401] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 1259.250840] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002 [ 1259.250879] usb 4-1: usb auto-resume [ 1259.317394] usb 4-1: Waited 0ms for CONNECT [ 1259.317403] usb 4-1: finish resume [ 1259.319228] hub 4-1:1.0: hub_resume [ 1259.346620] usb 4-1-port2: status 0263 change 0000 [ 1259.347948] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000 [ 1259.349107] r8152-cfgselector 4-1.2: usb auto-resume [ 1259.366281] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0004 [ 1259.413272] r8152-cfgselector 4-1.2: Waited 0ms for CONNECT [ 1259.413282] r8152-cfgselector 4-1.2: finish resume [ 1259.414117] hub 4-1:1.0: state 7 ports 4 chg 0000 evt 0000
On 21.2.2024 13.19, Paul Menzel wrote: > [CC: +Mike, +Hans, +Kai-Heng] > > > On the Dell XPS 13 9360/0596KF, BIOS 2.21.0 06/02/2022, the warning is also gone with v2 of your patches. > Thanks for testing, I'll submit these as proper patches. Thanks -Mathias
Dear Mathias, Am 22.02.24 um 14:19 schrieb Mathias Nyman: > On 21.2.2024 13.19, Paul Menzel wrote: >> [CC: +Mike, +Hans, +Kai-Heng] >> >> >> On the Dell XPS 13 9360/0596KF, BIOS 2.21.0 06/02/2022, the warning is >> also gone with v2 of your patches. > > Thanks for testing, I'll submit these as proper patches. Just a note, that I also successfully tested it on the Dell Precision 3620 and documented this in the Linux Kernel Bugzilla issue [1]. I wasn’t able to test the two other systems yet. Kind regards, Paul [1]: https://bugzilla.kernel.org/show_bug.cgi?id=218486
diff --git a/drivers/usb/core/port.c b/drivers/usb/core/port.c index c628c1abc907..4d63496f98b6 100644 --- a/drivers/usb/core/port.c +++ b/drivers/usb/core/port.c @@ -573,7 +573,7 @@ static int match_location(struct usb_device *peer_hdev, void *p) struct usb_hub *peer_hub = usb_hub_to_struct_hub(peer_hdev); struct usb_device *hdev = to_usb_device(port_dev->dev.parent->parent); - if (!peer_hub) + if (!peer_hub || port_dev->connect_type == USB_PORT_NOT_USED) return 0; hcd = bus_to_hcd(hdev->bus); @@ -584,7 +584,8 @@ static int match_location(struct usb_device *peer_hdev, void *p) for (port1 = 1; port1 <= peer_hdev->maxchild; port1++) { peer = peer_hub->ports[port1 - 1]; - if (peer && peer->location == port_dev->location) { + if (peer && peer->connect_type != USB_PORT_NOT_USED && + peer->location == port_dev->location) { link_peers_report(port_dev, peer); return 1; /* done */ }
Unused USB ports may have bogus location data in ACPI PLD tables. This causes port peering failures as these unused USB2 and USB3 ports location may match. This is seen on DELL systems where all unused ports return zeroed location data. Don't try to peer or match ports that have connect type set to USB_PORT_NOT_USED. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> --- v1 -> v2 Don't try to peer unused ports instead of reacting to failed peering drivers/usb/core/port.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)