| Message ID | 3bb95f1d795eede63284dbcb224e06ea6886b421.1707530671.git.daniel@makrotopia.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v3,1/2] dt-bindings: phy: mediatek,mt7988-xfi-tphy: add new bindings | expand |
On Sat, Feb 10, 2024 at 02:10:24AM +0000, Daniel Golle wrote: > Add driver for MediaTek's XFI T-PHY which can be found in the MT7988 > SoC. The XFI T-PHY is a 10 Gigabit/s Ethernet SerDes PHY with muxes on > the internal side to be used with either USXGMII PCS or LynxI PCS, > depending on the selected PHY interface mode. > > The PHY can operates only in PHY_MODE_ETHERNET, the submode is one of > PHY_INTERFACE_MODE_* corresponding to the supported modes: > > * USXGMII \ > * 10GBase-R }- USXGMII PCS - XGDM \ > * 5GBase-R / \ > }- Ethernet MAC > * 2500Base-X \ / > * 1000Base-X }- LynxI PCS - GDM / > * Cisco SGMII (MAC side) / > > In order to work-around a performance issue present on the first of > two XFI T-PHYs present in MT7988, special tuning is applied which can be > selected by adding the 'mediatek,usxgmii-performance-errata' property to > the device tree node. > > There is no documentation for most registers used for the > analog/tuning part, however, most of the registers have been partially > reverse-engineered from MediaTek's SDK implementation (an opaque > sequence of 32-bit register writes) and descriptions for all relevant > digital registers and bits such as resets and muxes have been supplied > by MediaTek. > > Signed-off-by: Daniel Golle <daniel@makrotopia.org> > Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> It's been a month since this patch was posted. Maybe it has somehow slipped under the table (or even under the carpet)? > --- > v3: no changes > v2: > * use IO helpers from mtk-io.h instead of rolling my own > * use devm_clk_bulk_get() > * yse devm_platform_ioremap_resource() > * unify name and description everywhere > * invert bool is_xgmii into bool use_lynxi_pcs and add comments > describing the meaning of each of the stack variables > * not much we can do about remaining magic values unless MTK provides > definitions for them > > > MAINTAINERS | 1 + > drivers/phy/mediatek/Kconfig | 12 + > drivers/phy/mediatek/Makefile | 1 + > drivers/phy/mediatek/phy-mtk-xfi-tphy.c | 360 ++++++++++++++++++++++++ > 4 files changed, 374 insertions(+) > create mode 100644 drivers/phy/mediatek/phy-mtk-xfi-tphy.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index 4be2fd097f261..616b86e3e62fd 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -13776,6 +13776,7 @@ L: netdev@vger.kernel.org > S: Maintained > F: drivers/net/phy/mediatek-ge-soc.c > F: drivers/net/phy/mediatek-ge.c > +F: drivers/phy/mediatek/phy-mtk-xfi-tphy.c > > MEDIATEK I2C CONTROLLER DRIVER > M: Qii Wang <qii.wang@mediatek.com> > diff --git a/drivers/phy/mediatek/Kconfig b/drivers/phy/mediatek/Kconfig > index 3849b7c87d287..117d0e84c7360 100644 > --- a/drivers/phy/mediatek/Kconfig > +++ b/drivers/phy/mediatek/Kconfig > @@ -13,6 +13,18 @@ config PHY_MTK_PCIE > callback for PCIe GEN3 port, it supports software efuse > initialization. > > +config PHY_MTK_XFI_TPHY > + tristate "MediaTek 10GE SerDes XFI T-PHY driver" > + depends on ARCH_MEDIATEK || COMPILE_TEST > + depends on OF && OF_ADDRESS > + depends on HAS_IOMEM > + select GENERIC_PHY > + help > + Say 'Y' here to add support for MediaTek XFI T-PHY driver. > + The driver provides access to the Ethernet SerDes T-PHY supporting > + 1GE and 2.5GE modes via the LynxI PCS, and 5GE and 10GE modes > + via the USXGMII PCS found in MediaTek SoCs with 10G Ethernet. > + > config PHY_MTK_TPHY > tristate "MediaTek T-PHY Driver" > depends on ARCH_MEDIATEK || COMPILE_TEST > diff --git a/drivers/phy/mediatek/Makefile b/drivers/phy/mediatek/Makefile > index f6e24a47e0815..1b8088df71e84 100644 > --- a/drivers/phy/mediatek/Makefile > +++ b/drivers/phy/mediatek/Makefile > @@ -8,6 +8,7 @@ obj-$(CONFIG_PHY_MTK_PCIE) += phy-mtk-pcie.o > obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o > obj-$(CONFIG_PHY_MTK_UFS) += phy-mtk-ufs.o > obj-$(CONFIG_PHY_MTK_XSPHY) += phy-mtk-xsphy.o > +obj-$(CONFIG_PHY_MTK_XFI_TPHY) += phy-mtk-xfi-tphy.o > > phy-mtk-hdmi-drv-y := phy-mtk-hdmi.o > phy-mtk-hdmi-drv-y += phy-mtk-hdmi-mt2701.o > diff --git a/drivers/phy/mediatek/phy-mtk-xfi-tphy.c b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c > new file mode 100644 > index 0000000000000..551d6cee33f94 > --- /dev/null > +++ b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c > @@ -0,0 +1,360 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later > +/* MediaTek 10GE SerDes XFI T-PHY driver > + * > + * Copyright (c) 2024 Daniel Golle <daniel@makrotopia.org> > + * Bc-bocun Chen <bc-bocun.chen@mediatek.com> > + * based on mtk_usxgmii.c and mtk_sgmii.c found in MediaTek's SDK (GPL-2.0) > + * Copyright (c) 2022 MediaTek Inc. > + * Author: Henry Yen <henry.yen@mediatek.com> > + */ > + > +#include <linux/module.h> > +#include <linux/device.h> > +#include <linux/platform_device.h> > +#include <linux/of.h> > +#include <linux/io.h> > +#include <linux/clk.h> > +#include <linux/reset.h> > +#include <linux/phy.h> > +#include <linux/phy/phy.h> > + > +#include "phy-mtk-io.h" > + > +#define MTK_XFI_TPHY_NUM_CLOCKS 2 > + > +#define REG_DIG_GLB_70 0x0070 > +#define XTP_PCS_RX_EQ_IN_PROGRESS(x) FIELD_PREP(GENMASK(25, 24), (x)) > +#define XTP_PCS_MODE_MASK GENMASK(17, 16) > +#define XTP_PCS_MODE(x) FIELD_PREP(GENMASK(17, 16), (x)) > +#define XTP_PCS_RST_B BIT(15) > +#define XTP_FRC_PCS_RST_B BIT(14) > +#define XTP_PCS_PWD_SYNC_MASK GENMASK(13, 12) > +#define XTP_PCS_PWD_SYNC(x) FIELD_PREP(XTP_PCS_PWD_SYNC_MASK, (x)) > +#define XTP_PCS_PWD_ASYNC_MASK GENMASK(11, 10) > +#define XTP_PCS_PWD_ASYNC(x) FIELD_PREP(XTP_PCS_PWD_ASYNC_MASK, (x)) > +#define XTP_FRC_PCS_PWD_ASYNC BIT(8) > +#define XTP_PCS_UPDT BIT(4) > +#define XTP_PCS_IN_FR_RG BIT(0) > + > +#define REG_DIG_GLB_F4 0x00f4 > +#define XFI_DPHY_PCS_SEL BIT(0) > +#define XFI_DPHY_PCS_SEL_SGMII FIELD_PREP(XFI_DPHY_PCS_SEL, 1) > +#define XFI_DPHY_PCS_SEL_USXGMII FIELD_PREP(XFI_DPHY_PCS_SEL, 0) > +#define XFI_DPHY_AD_SGDT_FRC_EN BIT(5) > + > +#define REG_DIG_LN_TRX_40 0x3040 > +#define XTP_LN_FRC_TX_DATA_EN BIT(29) > +#define XTP_LN_TX_DATA_EN BIT(28) > + > +#define REG_DIG_LN_TRX_B0 0x30b0 > +#define XTP_LN_FRC_TX_MACCK_EN BIT(5) > +#define XTP_LN_TX_MACCK_EN BIT(4) > + > +#define REG_ANA_GLB_D0 0x90d0 > +#define XTP_GLB_USXGMII_SEL_MASK GENMASK(3, 1) > +#define XTP_GLB_USXGMII_SEL(x) FIELD_PREP(GENMASK(3, 1), (x)) > +#define XTP_GLB_USXGMII_EN BIT(0) > + > +struct mtk_xfi_tphy { > + void __iomem *base; > + struct device *dev; > + struct reset_control *reset; > + struct clk_bulk_data clocks[MTK_XFI_TPHY_NUM_CLOCKS]; > + bool da_war; > +}; > + > +static void mtk_xfi_tphy_setup(struct mtk_xfi_tphy *xfi_tphy, > + phy_interface_t interface) > +{ > + /* Override 10GBase-R tuning value if work-around is selected */ > + bool da_war = (xfi_tphy->da_war && (interface == PHY_INTERFACE_MODE_10GBASER)); > + /* Bools to make setting up values for specific PHY speeds easier */ > + bool is_2p5g = (interface == PHY_INTERFACE_MODE_2500BASEX); > + bool is_1g = (interface == PHY_INTERFACE_MODE_1000BASEX || > + interface == PHY_INTERFACE_MODE_SGMII); > + bool is_10g = (interface == PHY_INTERFACE_MODE_10GBASER || > + interface == PHY_INTERFACE_MODE_USXGMII); > + bool is_5g = (interface == PHY_INTERFACE_MODE_5GBASER); > + /* Bool to configure input mux to either > + * - USXGMII PCS (64b/66b coding) for 5G/10G > + * - LynxI PCS (8b/10b coding) for 1G/2.5G > + */ > + bool use_lynxi_pcs = (is_1g || is_2p5g); > + > + dev_dbg(xfi_tphy->dev, "setting up for mode %s\n", phy_modes(interface)); > + > + /* Setup PLL setting */ > + mtk_phy_update_bits(xfi_tphy->base + 0x9024, 0x100000, is_10g ? 0x0 : 0x100000); > + mtk_phy_update_bits(xfi_tphy->base + 0x2020, 0x202000, is_5g ? 0x202000 : 0x0); > + mtk_phy_update_bits(xfi_tphy->base + 0x2030, 0x500, is_1g ? 0x0 : 0x500); > + mtk_phy_update_bits(xfi_tphy->base + 0x2034, 0xa00, is_1g ? 0x0 : 0xa00); > + mtk_phy_update_bits(xfi_tphy->base + 0x2040, 0x340000, is_1g ? 0x200000 : 0x140000); > + > + /* Setup RXFE BW setting */ > + mtk_phy_update_bits(xfi_tphy->base + 0x50f0, 0xc10, is_1g ? 0x410 : is_5g ? 0x800 : 0x400); > + mtk_phy_update_bits(xfi_tphy->base + 0x50e0, 0x4000, is_5g ? 0x0 : 0x4000); > + > + /* Setup RX CDR setting */ > + mtk_phy_update_bits(xfi_tphy->base + 0x506c, 0x30000, is_5g ? 0x0 : 0x30000); > + mtk_phy_update_bits(xfi_tphy->base + 0x5070, 0x670000, is_5g ? 0x620000 : 0x50000); > + mtk_phy_update_bits(xfi_tphy->base + 0x5074, 0x180000, is_5g ? 0x180000 : 0x0); > + mtk_phy_update_bits(xfi_tphy->base + 0x5078, 0xf000400, is_5g ? 0x8000000 : > + 0x7000400); > + mtk_phy_update_bits(xfi_tphy->base + 0x507c, 0x5000500, is_5g ? 0x4000400 : > + 0x1000100); > + mtk_phy_update_bits(xfi_tphy->base + 0x5080, 0x1410, is_1g ? 0x400 : is_5g ? 0x1010 : 0x0); > + mtk_phy_update_bits(xfi_tphy->base + 0x5084, 0x30300, is_1g ? 0x30300 : > + is_5g ? 0x30100 : > + 0x100); > + mtk_phy_update_bits(xfi_tphy->base + 0x5088, 0x60200, is_1g ? 0x20200 : > + is_5g ? 0x40000 : > + 0x20000); > + > + /* Setting RXFE adaptation range setting */ > + mtk_phy_update_bits(xfi_tphy->base + 0x50e4, 0xc0000, is_5g ? 0x0 : 0xc0000); > + mtk_phy_update_bits(xfi_tphy->base + 0x50e8, 0x40000, is_5g ? 0x0 : 0x40000); > + mtk_phy_update_bits(xfi_tphy->base + 0x50ec, 0xa00, is_1g ? 0x200 : 0x800); > + mtk_phy_update_bits(xfi_tphy->base + 0x50a8, 0xee0000, is_5g ? 0x800000 : > + 0x6e0000); > + mtk_phy_update_bits(xfi_tphy->base + 0x6004, 0x190000, is_5g ? 0x0 : 0x190000); > + > + if (is_10g) > + writel(0x01423342, xfi_tphy->base + 0x00f8); > + else if (is_5g) > + writel(0x00a132a1, xfi_tphy->base + 0x00f8); > + else if (is_2p5g) > + writel(0x009c329c, xfi_tphy->base + 0x00f8); > + else > + writel(0x00fa32fa, xfi_tphy->base + 0x00f8); > + > + /* Force SGDT_OUT off and select PCS */ > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_F4, > + XFI_DPHY_AD_SGDT_FRC_EN | XFI_DPHY_PCS_SEL, > + XFI_DPHY_AD_SGDT_FRC_EN | > + (use_lynxi_pcs ? XFI_DPHY_PCS_SEL_SGMII : > + XFI_DPHY_PCS_SEL_USXGMII)); > + > + /* Force GLB_CKDET_OUT */ > + mtk_phy_set_bits(xfi_tphy->base + 0x0030, 0xc00); > + > + /* Force AEQ on */ > + writel(XTP_PCS_RX_EQ_IN_PROGRESS(2) | XTP_PCS_PWD_SYNC(2) | XTP_PCS_PWD_ASYNC(2), > + xfi_tphy->base + REG_DIG_GLB_70); > + > + usleep_range(1, 5); > + > + /* Setup TX DA default value */ > + mtk_phy_update_bits(xfi_tphy->base + 0x30b0, 0x30, 0x20); > + writel(0x00008a01, xfi_tphy->base + 0x3028); > + writel(0x0000a884, xfi_tphy->base + 0x302c); > + writel(0x00083002, xfi_tphy->base + 0x3024); > + > + /* Setup RG default value */ > + if (use_lynxi_pcs) { > + writel(0x00011110, xfi_tphy->base + 0x3010); > + writel(0x40704000, xfi_tphy->base + 0x3048); > + } else { > + writel(0x00022220, xfi_tphy->base + 0x3010); > + writel(0x0f020a01, xfi_tphy->base + 0x5064); > + writel(0x06100600, xfi_tphy->base + 0x50b4); > + if (interface == PHY_INTERFACE_MODE_USXGMII) > + writel(0x40704000, xfi_tphy->base + 0x3048); > + else > + writel(0x47684100, xfi_tphy->base + 0x3048); > + } > + > + if (is_1g) > + writel(0x0000c000, xfi_tphy->base + 0x3064); > + > + /* Setup RX EQ initial value */ > + mtk_phy_update_bits(xfi_tphy->base + 0x3050, 0xa8000000, > + (interface != PHY_INTERFACE_MODE_10GBASER) ? 0xa8000000 : 0x0); > + mtk_phy_update_bits(xfi_tphy->base + 0x3054, 0xaa, > + (interface != PHY_INTERFACE_MODE_10GBASER) ? 0xaa : 0x0); > + > + if (!use_lynxi_pcs) > + writel(0x00000f00, xfi_tphy->base + 0x306c); > + else if (is_2p5g) > + writel(0x22000f00, xfi_tphy->base + 0x306c); > + else > + writel(0x20200f00, xfi_tphy->base + 0x306c); > + > + mtk_phy_update_bits(xfi_tphy->base + 0xa008, 0x10000, da_war ? 0x10000 : 0x0); > + > + mtk_phy_update_bits(xfi_tphy->base + 0xa060, 0x50000, use_lynxi_pcs ? 0x50000 : 0x40000); > + > + /* Setup PHYA speed */ > + mtk_phy_update_bits(xfi_tphy->base + REG_ANA_GLB_D0, > + XTP_GLB_USXGMII_SEL_MASK | XTP_GLB_USXGMII_EN, > + is_10g ? XTP_GLB_USXGMII_SEL(0) : > + is_5g ? XTP_GLB_USXGMII_SEL(1) : > + is_2p5g ? XTP_GLB_USXGMII_SEL(2) : > + XTP_GLB_USXGMII_SEL(3)); > + mtk_phy_set_bits(xfi_tphy->base + REG_ANA_GLB_D0, XTP_GLB_USXGMII_EN); > + > + /* Release reset */ > + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_GLB_70, > + XTP_PCS_RST_B | XTP_FRC_PCS_RST_B); > + usleep_range(150, 500); > + > + /* Switch to P0 */ > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, > + XTP_PCS_IN_FR_RG | > + XTP_FRC_PCS_PWD_ASYNC | > + XTP_PCS_PWD_ASYNC_MASK | > + XTP_PCS_PWD_SYNC_MASK | > + XTP_PCS_UPDT, > + XTP_PCS_IN_FR_RG | > + XTP_FRC_PCS_PWD_ASYNC | > + XTP_PCS_UPDT); > + usleep_range(1, 5); > + > + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_70, XTP_PCS_UPDT); > + usleep_range(15, 50); > + > + if (use_lynxi_pcs) { > + /* Switch to Gen2 */ > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, > + XTP_PCS_MODE_MASK | XTP_PCS_UPDT, > + XTP_PCS_MODE(1) | XTP_PCS_UPDT); > + } else { > + /* Switch to Gen3 */ > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, > + XTP_PCS_MODE_MASK | XTP_PCS_UPDT, > + XTP_PCS_MODE(2) | XTP_PCS_UPDT); > + } > + usleep_range(1, 5); > + > + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_70, XTP_PCS_UPDT); > + > + usleep_range(100, 500); > + > + /* Enable MAC CK */ > + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_LN_TRX_B0, XTP_LN_TX_MACCK_EN); > + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_F4, XFI_DPHY_AD_SGDT_FRC_EN); > + > + /* Enable TX data */ > + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_LN_TRX_40, > + XTP_LN_FRC_TX_DATA_EN | XTP_LN_TX_DATA_EN); > + usleep_range(400, 1000); > +} > + > +static int mtk_xfi_tphy_set_mode(struct phy *phy, enum phy_mode mode, int > + submode) > +{ > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > + > + if (mode != PHY_MODE_ETHERNET) > + return -EINVAL; > + > + switch (submode) { > + case PHY_INTERFACE_MODE_1000BASEX: > + case PHY_INTERFACE_MODE_2500BASEX: > + case PHY_INTERFACE_MODE_SGMII: > + case PHY_INTERFACE_MODE_5GBASER: > + case PHY_INTERFACE_MODE_10GBASER: > + case PHY_INTERFACE_MODE_USXGMII: > + mtk_xfi_tphy_setup(xfi_tphy, submode); > + return 0; > + default: > + return -EINVAL; > + } > +} > + > +static int mtk_xfi_tphy_reset(struct phy *phy) > +{ > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > + > + reset_control_assert(xfi_tphy->reset); > + usleep_range(100, 500); > + reset_control_deassert(xfi_tphy->reset); > + usleep_range(1, 10); > + > + return 0; > +} > + > +static int mtk_xfi_tphy_power_on(struct phy *phy) > +{ > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > + > + return clk_bulk_prepare_enable(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); > +} > + > +static int mtk_xfi_tphy_power_off(struct phy *phy) > +{ > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > + > + clk_bulk_disable_unprepare(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); > + > + return 0; > +} > + > +static const struct phy_ops mtk_xfi_tphy_ops = { > + .power_on = mtk_xfi_tphy_power_on, > + .power_off = mtk_xfi_tphy_power_off, > + .set_mode = mtk_xfi_tphy_set_mode, > + .reset = mtk_xfi_tphy_reset, > + .owner = THIS_MODULE, > +}; > + > +static int mtk_xfi_tphy_probe(struct platform_device *pdev) > +{ > + struct device_node *np = pdev->dev.of_node; > + struct phy_provider *phy_provider; > + struct mtk_xfi_tphy *xfi_tphy; > + struct phy *phy; > + int ret; > + > + if (!np) > + return -ENODEV; > + > + xfi_tphy = devm_kzalloc(&pdev->dev, sizeof(*xfi_tphy), GFP_KERNEL); > + if (!xfi_tphy) > + return -ENOMEM; > + > + xfi_tphy->base = devm_platform_ioremap_resource(pdev, 0); > + if (IS_ERR(xfi_tphy->base)) > + return PTR_ERR(xfi_tphy->base); > + > + xfi_tphy->dev = &pdev->dev; > + xfi_tphy->clocks[0].id = "topxtal"; > + xfi_tphy->clocks[1].id = "xfipll"; > + ret = devm_clk_bulk_get(&pdev->dev, MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); > + if (ret) > + return ret; > + > + xfi_tphy->reset = devm_reset_control_get_exclusive(&pdev->dev, NULL); > + if (IS_ERR(xfi_tphy->reset)) > + return PTR_ERR(xfi_tphy->reset); > + > + xfi_tphy->da_war = of_property_read_bool(np, "mediatek,usxgmii-performance-errata"); > + > + phy = devm_phy_create(&pdev->dev, NULL, &mtk_xfi_tphy_ops); > + if (IS_ERR(phy)) > + return PTR_ERR(phy); > + > + phy_set_drvdata(phy, xfi_tphy); > + phy_provider = devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate); > + > + return PTR_ERR_OR_ZERO(phy_provider); > +} > + > +static const struct of_device_id mtk_xfi_tphy_match[] = { > + { .compatible = "mediatek,mt7988-xfi-tphy", }, > + { /* sentinel */ } > +}; > +MODULE_DEVICE_TABLE(of, mtk_xfi_tphy_match); > + > +static struct platform_driver mtk_xfi_tphy_driver = { > + .probe = mtk_xfi_tphy_probe, > + .driver = { > + .name = "mtk-xfi-tphy", > + .of_match_table = mtk_xfi_tphy_match, > + }, > +}; > +module_platform_driver(mtk_xfi_tphy_driver); > + > +MODULE_DESCRIPTION("MediaTek 10GE SerDes XFI T-PHY driver"); > +MODULE_AUTHOR("Daniel Golle <daniel@makrotopia.org>"); > +MODULE_AUTHOR("Bc-bocun Chen <bc-bocun.chen@mediatek.com>"); > +MODULE_LICENSE("GPL"); > -- > 2.43.0
On Sat, 9 Mar 2024 02:30:25 +0000 Daniel Golle wrote: > > Signed-off-by: Daniel Golle <daniel@makrotopia.org> > > Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> > > It's been a month since this patch was posted. Maybe it has somehow > slipped under the table (or even under the carpet)? Lots of people in To:, lets direct the question to Vinod? Most active generic PHY maintainer according to git, Vinod?
On 08-03-24, 19:36, Jakub Kicinski wrote: > On Sat, 9 Mar 2024 02:30:25 +0000 Daniel Golle wrote: > > > Signed-off-by: Daniel Golle <daniel@makrotopia.org> > > > Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> > > > > It's been a month since this patch was posted. Maybe it has somehow > > slipped under the table (or even under the carpet)? Nope, somehow I dont have this in inbox, i think i have some issues with gmail and list server, > Lots of people in To:, lets direct the question to Vinod? > Most active generic PHY maintainer according to git, Vinod? thanks for letting me know... I will review it in next few days (pulled it from lore using b4)
Hi Vinod, On Sun, Mar 10, 2024 at 10:16:51PM +0530, Vinod Koul wrote: > On 08-03-24, 19:36, Jakub Kicinski wrote: > > On Sat, 9 Mar 2024 02:30:25 +0000 Daniel Golle wrote: > > > > Signed-off-by: Daniel Golle <daniel@makrotopia.org> > > > > Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> > > > > > > It's been a month since this patch was posted. Maybe it has somehow > > > slipped under the table (or even under the carpet)? > > Nope, somehow I dont have this in inbox, i think i have some issues with > gmail and list server, The series can be found here, just in case: https://patchwork.kernel.org/project/linux-phy/list/?series=824861 > > > Lots of people in To:, lets direct the question to Vinod? > > Most active generic PHY maintainer according to git, Vinod? > > thanks for letting me know... > I will review it in next few days (pulled it from lore using b4) It'd be great if you can take a look and maybe merge this so we can proceed adding support for MT7988. Thank you!
On 10-02-24, 02:10, Daniel Golle wrote: > Add driver for MediaTek's XFI T-PHY which can be found in the MT7988 What does XFI mean? > SoC. The XFI T-PHY is a 10 Gigabit/s Ethernet SerDes PHY with muxes on > the internal side to be used with either USXGMII PCS or LynxI PCS, > depending on the selected PHY interface mode. > > The PHY can operates only in PHY_MODE_ETHERNET, the submode is one of > PHY_INTERFACE_MODE_* corresponding to the supported modes: > > * USXGMII \ > * 10GBase-R }- USXGMII PCS - XGDM \ > * 5GBase-R / \ > }- Ethernet MAC > * 2500Base-X \ / > * 1000Base-X }- LynxI PCS - GDM / > * Cisco SGMII (MAC side) / > > In order to work-around a performance issue present on the first of > two XFI T-PHYs present in MT7988, special tuning is applied which can be > selected by adding the 'mediatek,usxgmii-performance-errata' property to > the device tree node. > > There is no documentation for most registers used for the > analog/tuning part, however, most of the registers have been partially > reverse-engineered from MediaTek's SDK implementation (an opaque > sequence of 32-bit register writes) and descriptions for all relevant > digital registers and bits such as resets and muxes have been supplied > by MediaTek. > > Signed-off-by: Daniel Golle <daniel@makrotopia.org> > Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> > --- > v3: no changes > v2: > * use IO helpers from mtk-io.h instead of rolling my own > * use devm_clk_bulk_get() > * yse devm_platform_ioremap_resource() > * unify name and description everywhere > * invert bool is_xgmii into bool use_lynxi_pcs and add comments > describing the meaning of each of the stack variables > * not much we can do about remaining magic values unless MTK provides > definitions for them > > > MAINTAINERS | 1 + > drivers/phy/mediatek/Kconfig | 12 + > drivers/phy/mediatek/Makefile | 1 + > drivers/phy/mediatek/phy-mtk-xfi-tphy.c | 360 ++++++++++++++++++++++++ > 4 files changed, 374 insertions(+) > create mode 100644 drivers/phy/mediatek/phy-mtk-xfi-tphy.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index 4be2fd097f261..616b86e3e62fd 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -13776,6 +13776,7 @@ L: netdev@vger.kernel.org > S: Maintained > F: drivers/net/phy/mediatek-ge-soc.c > F: drivers/net/phy/mediatek-ge.c > +F: drivers/phy/mediatek/phy-mtk-xfi-tphy.c > > MEDIATEK I2C CONTROLLER DRIVER > M: Qii Wang <qii.wang@mediatek.com> > diff --git a/drivers/phy/mediatek/Kconfig b/drivers/phy/mediatek/Kconfig > index 3849b7c87d287..117d0e84c7360 100644 > --- a/drivers/phy/mediatek/Kconfig > +++ b/drivers/phy/mediatek/Kconfig > @@ -13,6 +13,18 @@ config PHY_MTK_PCIE > callback for PCIe GEN3 port, it supports software efuse > initialization. > > +config PHY_MTK_XFI_TPHY > + tristate "MediaTek 10GE SerDes XFI T-PHY driver" > + depends on ARCH_MEDIATEK || COMPILE_TEST > + depends on OF && OF_ADDRESS why both, is OF not enough? > + depends on HAS_IOMEM > + select GENERIC_PHY > + help > + Say 'Y' here to add support for MediaTek XFI T-PHY driver. > + The driver provides access to the Ethernet SerDes T-PHY supporting > + 1GE and 2.5GE modes via the LynxI PCS, and 5GE and 10GE modes > + via the USXGMII PCS found in MediaTek SoCs with 10G Ethernet. > + > config PHY_MTK_TPHY > tristate "MediaTek T-PHY Driver" > depends on ARCH_MEDIATEK || COMPILE_TEST > diff --git a/drivers/phy/mediatek/Makefile b/drivers/phy/mediatek/Makefile > index f6e24a47e0815..1b8088df71e84 100644 > --- a/drivers/phy/mediatek/Makefile > +++ b/drivers/phy/mediatek/Makefile > @@ -8,6 +8,7 @@ obj-$(CONFIG_PHY_MTK_PCIE) += phy-mtk-pcie.o > obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o > obj-$(CONFIG_PHY_MTK_UFS) += phy-mtk-ufs.o > obj-$(CONFIG_PHY_MTK_XSPHY) += phy-mtk-xsphy.o > +obj-$(CONFIG_PHY_MTK_XFI_TPHY) += phy-mtk-xfi-tphy.o > > phy-mtk-hdmi-drv-y := phy-mtk-hdmi.o > phy-mtk-hdmi-drv-y += phy-mtk-hdmi-mt2701.o > diff --git a/drivers/phy/mediatek/phy-mtk-xfi-tphy.c b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c > new file mode 100644 > index 0000000000000..551d6cee33f94 > --- /dev/null > +++ b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c > @@ -0,0 +1,360 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later > +/* MediaTek 10GE SerDes XFI T-PHY driver > + * > + * Copyright (c) 2024 Daniel Golle <daniel@makrotopia.org> > + * Bc-bocun Chen <bc-bocun.chen@mediatek.com> > + * based on mtk_usxgmii.c and mtk_sgmii.c found in MediaTek's SDK (GPL-2.0) > + * Copyright (c) 2022 MediaTek Inc. > + * Author: Henry Yen <henry.yen@mediatek.com> > + */ > + > +#include <linux/module.h> > +#include <linux/device.h> > +#include <linux/platform_device.h> > +#include <linux/of.h> > +#include <linux/io.h> > +#include <linux/clk.h> > +#include <linux/reset.h> > +#include <linux/phy.h> > +#include <linux/phy/phy.h> > + > +#include "phy-mtk-io.h" > + > +#define MTK_XFI_TPHY_NUM_CLOCKS 2 > + > +#define REG_DIG_GLB_70 0x0070 > +#define XTP_PCS_RX_EQ_IN_PROGRESS(x) FIELD_PREP(GENMASK(25, 24), (x)) > +#define XTP_PCS_MODE_MASK GENMASK(17, 16) > +#define XTP_PCS_MODE(x) FIELD_PREP(GENMASK(17, 16), (x)) > +#define XTP_PCS_RST_B BIT(15) > +#define XTP_FRC_PCS_RST_B BIT(14) > +#define XTP_PCS_PWD_SYNC_MASK GENMASK(13, 12) > +#define XTP_PCS_PWD_SYNC(x) FIELD_PREP(XTP_PCS_PWD_SYNC_MASK, (x)) > +#define XTP_PCS_PWD_ASYNC_MASK GENMASK(11, 10) > +#define XTP_PCS_PWD_ASYNC(x) FIELD_PREP(XTP_PCS_PWD_ASYNC_MASK, (x)) > +#define XTP_FRC_PCS_PWD_ASYNC BIT(8) > +#define XTP_PCS_UPDT BIT(4) > +#define XTP_PCS_IN_FR_RG BIT(0) > + > +#define REG_DIG_GLB_F4 0x00f4 > +#define XFI_DPHY_PCS_SEL BIT(0) > +#define XFI_DPHY_PCS_SEL_SGMII FIELD_PREP(XFI_DPHY_PCS_SEL, 1) > +#define XFI_DPHY_PCS_SEL_USXGMII FIELD_PREP(XFI_DPHY_PCS_SEL, 0) > +#define XFI_DPHY_AD_SGDT_FRC_EN BIT(5) > + > +#define REG_DIG_LN_TRX_40 0x3040 > +#define XTP_LN_FRC_TX_DATA_EN BIT(29) > +#define XTP_LN_TX_DATA_EN BIT(28) > + > +#define REG_DIG_LN_TRX_B0 0x30b0 > +#define XTP_LN_FRC_TX_MACCK_EN BIT(5) > +#define XTP_LN_TX_MACCK_EN BIT(4) > + > +#define REG_ANA_GLB_D0 0x90d0 > +#define XTP_GLB_USXGMII_SEL_MASK GENMASK(3, 1) > +#define XTP_GLB_USXGMII_SEL(x) FIELD_PREP(GENMASK(3, 1), (x)) > +#define XTP_GLB_USXGMII_EN BIT(0) > + > +struct mtk_xfi_tphy { > + void __iomem *base; > + struct device *dev; > + struct reset_control *reset; > + struct clk_bulk_data clocks[MTK_XFI_TPHY_NUM_CLOCKS]; > + bool da_war; > +}; > + > +static void mtk_xfi_tphy_setup(struct mtk_xfi_tphy *xfi_tphy, > + phy_interface_t interface) > +{ > + /* Override 10GBase-R tuning value if work-around is selected */ > + bool da_war = (xfi_tphy->da_war && (interface == PHY_INTERFACE_MODE_10GBASER)); why do you need braces around this? > + /* Bools to make setting up values for specific PHY speeds easier */ > + bool is_2p5g = (interface == PHY_INTERFACE_MODE_2500BASEX); > + bool is_1g = (interface == PHY_INTERFACE_MODE_1000BASEX || > + interface == PHY_INTERFACE_MODE_SGMII); > + bool is_10g = (interface == PHY_INTERFACE_MODE_10GBASER || > + interface == PHY_INTERFACE_MODE_USXGMII); > + bool is_5g = (interface == PHY_INTERFACE_MODE_5GBASER); > + /* Bool to configure input mux to either > + * - USXGMII PCS (64b/66b coding) for 5G/10G > + * - LynxI PCS (8b/10b coding) for 1G/2.5G > + */ > + bool use_lynxi_pcs = (is_1g || is_2p5g); This is quite terrible to read, how about declaring variables first and then doing the initialization? > + > + dev_dbg(xfi_tphy->dev, "setting up for mode %s\n", phy_modes(interface)); > + > + /* Setup PLL setting */ > + mtk_phy_update_bits(xfi_tphy->base + 0x9024, 0x100000, is_10g ? 0x0 : 0x100000); > + mtk_phy_update_bits(xfi_tphy->base + 0x2020, 0x202000, is_5g ? 0x202000 : 0x0); > + mtk_phy_update_bits(xfi_tphy->base + 0x2030, 0x500, is_1g ? 0x0 : 0x500); > + mtk_phy_update_bits(xfi_tphy->base + 0x2034, 0xa00, is_1g ? 0x0 : 0xa00); > + mtk_phy_update_bits(xfi_tphy->base + 0x2040, 0x340000, is_1g ? 0x200000 : 0x140000); magic numbers? > + > + /* Setup RXFE BW setting */ > + mtk_phy_update_bits(xfi_tphy->base + 0x50f0, 0xc10, is_1g ? 0x410 : is_5g ? 0x800 : 0x400); > + mtk_phy_update_bits(xfi_tphy->base + 0x50e0, 0x4000, is_5g ? 0x0 : 0x4000); > + > + /* Setup RX CDR setting */ > + mtk_phy_update_bits(xfi_tphy->base + 0x506c, 0x30000, is_5g ? 0x0 : 0x30000); > + mtk_phy_update_bits(xfi_tphy->base + 0x5070, 0x670000, is_5g ? 0x620000 : 0x50000); > + mtk_phy_update_bits(xfi_tphy->base + 0x5074, 0x180000, is_5g ? 0x180000 : 0x0); > + mtk_phy_update_bits(xfi_tphy->base + 0x5078, 0xf000400, is_5g ? 0x8000000 : > + 0x7000400); > + mtk_phy_update_bits(xfi_tphy->base + 0x507c, 0x5000500, is_5g ? 0x4000400 : > + 0x1000100); > + mtk_phy_update_bits(xfi_tphy->base + 0x5080, 0x1410, is_1g ? 0x400 : is_5g ? 0x1010 : 0x0); > + mtk_phy_update_bits(xfi_tphy->base + 0x5084, 0x30300, is_1g ? 0x30300 : > + is_5g ? 0x30100 : > + 0x100); > + mtk_phy_update_bits(xfi_tphy->base + 0x5088, 0x60200, is_1g ? 0x20200 : > + is_5g ? 0x40000 : > + 0x20000); > + > + /* Setting RXFE adaptation range setting */ > + mtk_phy_update_bits(xfi_tphy->base + 0x50e4, 0xc0000, is_5g ? 0x0 : 0xc0000); > + mtk_phy_update_bits(xfi_tphy->base + 0x50e8, 0x40000, is_5g ? 0x0 : 0x40000); > + mtk_phy_update_bits(xfi_tphy->base + 0x50ec, 0xa00, is_1g ? 0x200 : 0x800); > + mtk_phy_update_bits(xfi_tphy->base + 0x50a8, 0xee0000, is_5g ? 0x800000 : > + 0x6e0000); > + mtk_phy_update_bits(xfi_tphy->base + 0x6004, 0x190000, is_5g ? 0x0 : 0x190000); > + > + if (is_10g) > + writel(0x01423342, xfi_tphy->base + 0x00f8); > + else if (is_5g) > + writel(0x00a132a1, xfi_tphy->base + 0x00f8); > + else if (is_2p5g) > + writel(0x009c329c, xfi_tphy->base + 0x00f8); > + else > + writel(0x00fa32fa, xfi_tphy->base + 0x00f8); > + > + /* Force SGDT_OUT off and select PCS */ > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_F4, > + XFI_DPHY_AD_SGDT_FRC_EN | XFI_DPHY_PCS_SEL, > + XFI_DPHY_AD_SGDT_FRC_EN | > + (use_lynxi_pcs ? XFI_DPHY_PCS_SEL_SGMII : > + XFI_DPHY_PCS_SEL_USXGMII)); > + > + /* Force GLB_CKDET_OUT */ > + mtk_phy_set_bits(xfi_tphy->base + 0x0030, 0xc00); > + > + /* Force AEQ on */ > + writel(XTP_PCS_RX_EQ_IN_PROGRESS(2) | XTP_PCS_PWD_SYNC(2) | XTP_PCS_PWD_ASYNC(2), > + xfi_tphy->base + REG_DIG_GLB_70); > + > + usleep_range(1, 5); > + > + /* Setup TX DA default value */ > + mtk_phy_update_bits(xfi_tphy->base + 0x30b0, 0x30, 0x20); > + writel(0x00008a01, xfi_tphy->base + 0x3028); > + writel(0x0000a884, xfi_tphy->base + 0x302c); > + writel(0x00083002, xfi_tphy->base + 0x3024); > + > + /* Setup RG default value */ > + if (use_lynxi_pcs) { > + writel(0x00011110, xfi_tphy->base + 0x3010); > + writel(0x40704000, xfi_tphy->base + 0x3048); > + } else { > + writel(0x00022220, xfi_tphy->base + 0x3010); > + writel(0x0f020a01, xfi_tphy->base + 0x5064); > + writel(0x06100600, xfi_tphy->base + 0x50b4); > + if (interface == PHY_INTERFACE_MODE_USXGMII) > + writel(0x40704000, xfi_tphy->base + 0x3048); > + else > + writel(0x47684100, xfi_tphy->base + 0x3048); > + } > + > + if (is_1g) > + writel(0x0000c000, xfi_tphy->base + 0x3064); > + > + /* Setup RX EQ initial value */ > + mtk_phy_update_bits(xfi_tphy->base + 0x3050, 0xa8000000, > + (interface != PHY_INTERFACE_MODE_10GBASER) ? 0xa8000000 : 0x0); > + mtk_phy_update_bits(xfi_tphy->base + 0x3054, 0xaa, > + (interface != PHY_INTERFACE_MODE_10GBASER) ? 0xaa : 0x0); > + > + if (!use_lynxi_pcs) > + writel(0x00000f00, xfi_tphy->base + 0x306c); > + else if (is_2p5g) > + writel(0x22000f00, xfi_tphy->base + 0x306c); > + else > + writel(0x20200f00, xfi_tphy->base + 0x306c); > + > + mtk_phy_update_bits(xfi_tphy->base + 0xa008, 0x10000, da_war ? 0x10000 : 0x0); > + > + mtk_phy_update_bits(xfi_tphy->base + 0xa060, 0x50000, use_lynxi_pcs ? 0x50000 : 0x40000); > + > + /* Setup PHYA speed */ > + mtk_phy_update_bits(xfi_tphy->base + REG_ANA_GLB_D0, > + XTP_GLB_USXGMII_SEL_MASK | XTP_GLB_USXGMII_EN, > + is_10g ? XTP_GLB_USXGMII_SEL(0) : > + is_5g ? XTP_GLB_USXGMII_SEL(1) : > + is_2p5g ? XTP_GLB_USXGMII_SEL(2) : > + XTP_GLB_USXGMII_SEL(3)); > + mtk_phy_set_bits(xfi_tphy->base + REG_ANA_GLB_D0, XTP_GLB_USXGMII_EN); > + > + /* Release reset */ > + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_GLB_70, > + XTP_PCS_RST_B | XTP_FRC_PCS_RST_B); > + usleep_range(150, 500); > + > + /* Switch to P0 */ > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, > + XTP_PCS_IN_FR_RG | > + XTP_FRC_PCS_PWD_ASYNC | > + XTP_PCS_PWD_ASYNC_MASK | > + XTP_PCS_PWD_SYNC_MASK | > + XTP_PCS_UPDT, > + XTP_PCS_IN_FR_RG | > + XTP_FRC_PCS_PWD_ASYNC | > + XTP_PCS_UPDT); > + usleep_range(1, 5); > + > + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_70, XTP_PCS_UPDT); > + usleep_range(15, 50); > + > + if (use_lynxi_pcs) { > + /* Switch to Gen2 */ > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, > + XTP_PCS_MODE_MASK | XTP_PCS_UPDT, > + XTP_PCS_MODE(1) | XTP_PCS_UPDT); > + } else { > + /* Switch to Gen3 */ > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, > + XTP_PCS_MODE_MASK | XTP_PCS_UPDT, > + XTP_PCS_MODE(2) | XTP_PCS_UPDT); > + } > + usleep_range(1, 5); > + > + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_70, XTP_PCS_UPDT); > + > + usleep_range(100, 500); > + > + /* Enable MAC CK */ > + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_LN_TRX_B0, XTP_LN_TX_MACCK_EN); > + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_F4, XFI_DPHY_AD_SGDT_FRC_EN); > + > + /* Enable TX data */ > + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_LN_TRX_40, > + XTP_LN_FRC_TX_DATA_EN | XTP_LN_TX_DATA_EN); > + usleep_range(400, 1000); > +} > + > +static int mtk_xfi_tphy_set_mode(struct phy *phy, enum phy_mode mode, int > + submode) > +{ > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > + > + if (mode != PHY_MODE_ETHERNET) > + return -EINVAL; > + > + switch (submode) { > + case PHY_INTERFACE_MODE_1000BASEX: > + case PHY_INTERFACE_MODE_2500BASEX: > + case PHY_INTERFACE_MODE_SGMII: > + case PHY_INTERFACE_MODE_5GBASER: > + case PHY_INTERFACE_MODE_10GBASER: > + case PHY_INTERFACE_MODE_USXGMII: > + mtk_xfi_tphy_setup(xfi_tphy, submode); > + return 0; > + default: > + return -EINVAL; > + } > +} > + > +static int mtk_xfi_tphy_reset(struct phy *phy) > +{ > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > + > + reset_control_assert(xfi_tphy->reset); > + usleep_range(100, 500); > + reset_control_deassert(xfi_tphy->reset); > + usleep_range(1, 10); > + > + return 0; > +} > + > +static int mtk_xfi_tphy_power_on(struct phy *phy) > +{ > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > + > + return clk_bulk_prepare_enable(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); > +} > + > +static int mtk_xfi_tphy_power_off(struct phy *phy) > +{ > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > + > + clk_bulk_disable_unprepare(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); > + > + return 0; > +} > + > +static const struct phy_ops mtk_xfi_tphy_ops = { > + .power_on = mtk_xfi_tphy_power_on, > + .power_off = mtk_xfi_tphy_power_off, > + .set_mode = mtk_xfi_tphy_set_mode, > + .reset = mtk_xfi_tphy_reset, > + .owner = THIS_MODULE, > +}; > + > +static int mtk_xfi_tphy_probe(struct platform_device *pdev) > +{ > + struct device_node *np = pdev->dev.of_node; > + struct phy_provider *phy_provider; > + struct mtk_xfi_tphy *xfi_tphy; > + struct phy *phy; > + int ret; > + > + if (!np) > + return -ENODEV; > + > + xfi_tphy = devm_kzalloc(&pdev->dev, sizeof(*xfi_tphy), GFP_KERNEL); > + if (!xfi_tphy) > + return -ENOMEM; > + > + xfi_tphy->base = devm_platform_ioremap_resource(pdev, 0); > + if (IS_ERR(xfi_tphy->base)) > + return PTR_ERR(xfi_tphy->base); > + > + xfi_tphy->dev = &pdev->dev; > + xfi_tphy->clocks[0].id = "topxtal"; > + xfi_tphy->clocks[1].id = "xfipll"; > + ret = devm_clk_bulk_get(&pdev->dev, MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); > + if (ret) > + return ret; > + > + xfi_tphy->reset = devm_reset_control_get_exclusive(&pdev->dev, NULL); > + if (IS_ERR(xfi_tphy->reset)) > + return PTR_ERR(xfi_tphy->reset); > + > + xfi_tphy->da_war = of_property_read_bool(np, "mediatek,usxgmii-performance-errata"); > + > + phy = devm_phy_create(&pdev->dev, NULL, &mtk_xfi_tphy_ops); > + if (IS_ERR(phy)) > + return PTR_ERR(phy); > + > + phy_set_drvdata(phy, xfi_tphy); > + phy_provider = devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate); > + > + return PTR_ERR_OR_ZERO(phy_provider); > +} > + > +static const struct of_device_id mtk_xfi_tphy_match[] = { > + { .compatible = "mediatek,mt7988-xfi-tphy", }, > + { /* sentinel */ } > +}; > +MODULE_DEVICE_TABLE(of, mtk_xfi_tphy_match); > + > +static struct platform_driver mtk_xfi_tphy_driver = { > + .probe = mtk_xfi_tphy_probe, > + .driver = { > + .name = "mtk-xfi-tphy", > + .of_match_table = mtk_xfi_tphy_match, > + }, > +}; > +module_platform_driver(mtk_xfi_tphy_driver); > + > +MODULE_DESCRIPTION("MediaTek 10GE SerDes XFI T-PHY driver"); > +MODULE_AUTHOR("Daniel Golle <daniel@makrotopia.org>"); > +MODULE_AUTHOR("Bc-bocun Chen <bc-bocun.chen@mediatek.com>"); > +MODULE_LICENSE("GPL"); > -- > 2.43.0
Hi Vinod, thank you for taking your time to review my submission! On Fri, Mar 29, 2024 at 12:22:47AM +0530, Vinod Koul wrote: > On 10-02-24, 02:10, Daniel Golle wrote: > > Add driver for MediaTek's XFI T-PHY which can be found in the MT7988 > > What does XFI mean? https://en.wikipedia.org/wiki/XFP_transceiver#XFI I chose this name because names of functions dealing with the phy in the vendor driver are prefixed "xfi_pextp_". The register space used by the phy is called "pextp", which could be read as "_P_CI _ex_press _T_-_P_hy", and that is quite misleading as this phy isn't used for anything related to PCIe, so I wanted to find a better name. XFI is still somehow related (as in: you would find the relevant places using grep in the vendor driver when looking for that) and seemed to at least somehow be aligned with the function of that phy: Dealing with (up to) 10 Gbit/s Ethernet SerDes signals. MediaTek calls phys with more than one potential use T-PHY or X-PHY: The capital letter 'T' graphically connects 3 points, two of them being on the upper side representing the internal components and one on the lower side representing the single external interface. Other vendors (like Marvell) call such things "combo phys". Anyway, if anyone has better ideas regarding the naming, now is the moment to speak up ;) > > > SoC. The XFI T-PHY is a 10 Gigabit/s Ethernet SerDes PHY with muxes on > > the internal side to be used with either USXGMII PCS or LynxI PCS, > > depending on the selected PHY interface mode. > > > > The PHY can operates only in PHY_MODE_ETHERNET, the submode is one of > > PHY_INTERFACE_MODE_* corresponding to the supported modes: > > > > * USXGMII \ > > * 10GBase-R }- USXGMII PCS - XGDM \ > > * 5GBase-R / \ > > }- Ethernet MAC > > * 2500Base-X \ / > > * 1000Base-X }- LynxI PCS - GDM / > > * Cisco SGMII (MAC side) / > > > > In order to work-around a performance issue present on the first of > > two XFI T-PHYs present in MT7988, special tuning is applied which can be > > selected by adding the 'mediatek,usxgmii-performance-errata' property to > > the device tree node. > > > > There is no documentation for most registers used for the > > analog/tuning part, however, most of the registers have been partially > > reverse-engineered from MediaTek's SDK implementation (an opaque > > sequence of 32-bit register writes) and descriptions for all relevant > > digital registers and bits such as resets and muxes have been supplied > > by MediaTek. > > > > Signed-off-by: Daniel Golle <daniel@makrotopia.org> > > Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> > > --- > > v3: no changes > > v2: > > * use IO helpers from mtk-io.h instead of rolling my own > > * use devm_clk_bulk_get() > > * yse devm_platform_ioremap_resource() > > * unify name and description everywhere > > * invert bool is_xgmii into bool use_lynxi_pcs and add comments > > describing the meaning of each of the stack variables > > * not much we can do about remaining magic values unless MTK provides > > definitions for them > > > > > > MAINTAINERS | 1 + > > drivers/phy/mediatek/Kconfig | 12 + > > drivers/phy/mediatek/Makefile | 1 + > > drivers/phy/mediatek/phy-mtk-xfi-tphy.c | 360 ++++++++++++++++++++++++ > > 4 files changed, 374 insertions(+) > > create mode 100644 drivers/phy/mediatek/phy-mtk-xfi-tphy.c > > > > diff --git a/MAINTAINERS b/MAINTAINERS > > index 4be2fd097f261..616b86e3e62fd 100644 > > --- a/MAINTAINERS > > +++ b/MAINTAINERS > > @@ -13776,6 +13776,7 @@ L: netdev@vger.kernel.org > > S: Maintained > > F: drivers/net/phy/mediatek-ge-soc.c > > F: drivers/net/phy/mediatek-ge.c > > +F: drivers/phy/mediatek/phy-mtk-xfi-tphy.c > > > > MEDIATEK I2C CONTROLLER DRIVER > > M: Qii Wang <qii.wang@mediatek.com> > > diff --git a/drivers/phy/mediatek/Kconfig b/drivers/phy/mediatek/Kconfig > > index 3849b7c87d287..117d0e84c7360 100644 > > --- a/drivers/phy/mediatek/Kconfig > > +++ b/drivers/phy/mediatek/Kconfig > > @@ -13,6 +13,18 @@ config PHY_MTK_PCIE > > callback for PCIe GEN3 port, it supports software efuse > > initialization. > > > > +config PHY_MTK_XFI_TPHY > > + tristate "MediaTek 10GE SerDes XFI T-PHY driver" > > + depends on ARCH_MEDIATEK || COMPILE_TEST > > + depends on OF && OF_ADDRESS > > why both, is OF not enough? As we are already also depending on HAS_IOMEM what is left there is basically just a !SPARC dependency. And that is probably a historic left-over and (according to commit 5ab5fc7e35705c from 2010...) should be re-evaluated. I'm happy to drop OF_ADDRESS and keep only HAS_IOMEM, and we shall see if any of the COMPILE_TESTs actually fails, given that everyone is fine with that. > > > + depends on HAS_IOMEM > > + select GENERIC_PHY > > + help > > + Say 'Y' here to add support for MediaTek XFI T-PHY driver. > > + The driver provides access to the Ethernet SerDes T-PHY supporting > > + 1GE and 2.5GE modes via the LynxI PCS, and 5GE and 10GE modes > > + via the USXGMII PCS found in MediaTek SoCs with 10G Ethernet. > > + > > config PHY_MTK_TPHY > > tristate "MediaTek T-PHY Driver" > > depends on ARCH_MEDIATEK || COMPILE_TEST > > diff --git a/drivers/phy/mediatek/Makefile b/drivers/phy/mediatek/Makefile > > index f6e24a47e0815..1b8088df71e84 100644 > > --- a/drivers/phy/mediatek/Makefile > > +++ b/drivers/phy/mediatek/Makefile > > @@ -8,6 +8,7 @@ obj-$(CONFIG_PHY_MTK_PCIE) += phy-mtk-pcie.o > > obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o > > obj-$(CONFIG_PHY_MTK_UFS) += phy-mtk-ufs.o > > obj-$(CONFIG_PHY_MTK_XSPHY) += phy-mtk-xsphy.o > > +obj-$(CONFIG_PHY_MTK_XFI_TPHY) += phy-mtk-xfi-tphy.o > > > > phy-mtk-hdmi-drv-y := phy-mtk-hdmi.o > > phy-mtk-hdmi-drv-y += phy-mtk-hdmi-mt2701.o > > diff --git a/drivers/phy/mediatek/phy-mtk-xfi-tphy.c b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c > > new file mode 100644 > > index 0000000000000..551d6cee33f94 > > --- /dev/null > > +++ b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c > > @@ -0,0 +1,360 @@ > > +// SPDX-License-Identifier: GPL-2.0-or-later > > +/* MediaTek 10GE SerDes XFI T-PHY driver > > + * > > + * Copyright (c) 2024 Daniel Golle <daniel@makrotopia.org> > > + * Bc-bocun Chen <bc-bocun.chen@mediatek.com> > > + * based on mtk_usxgmii.c and mtk_sgmii.c found in MediaTek's SDK (GPL-2.0) > > + * Copyright (c) 2022 MediaTek Inc. > > + * Author: Henry Yen <henry.yen@mediatek.com> > > + */ > > + > > +#include <linux/module.h> > > +#include <linux/device.h> > > +#include <linux/platform_device.h> > > +#include <linux/of.h> > > +#include <linux/io.h> > > +#include <linux/clk.h> > > +#include <linux/reset.h> > > +#include <linux/phy.h> > > +#include <linux/phy/phy.h> > > + > > +#include "phy-mtk-io.h" > > + > > +#define MTK_XFI_TPHY_NUM_CLOCKS 2 > > + > > +#define REG_DIG_GLB_70 0x0070 > > +#define XTP_PCS_RX_EQ_IN_PROGRESS(x) FIELD_PREP(GENMASK(25, 24), (x)) > > +#define XTP_PCS_MODE_MASK GENMASK(17, 16) > > +#define XTP_PCS_MODE(x) FIELD_PREP(GENMASK(17, 16), (x)) > > +#define XTP_PCS_RST_B BIT(15) > > +#define XTP_FRC_PCS_RST_B BIT(14) > > +#define XTP_PCS_PWD_SYNC_MASK GENMASK(13, 12) > > +#define XTP_PCS_PWD_SYNC(x) FIELD_PREP(XTP_PCS_PWD_SYNC_MASK, (x)) > > +#define XTP_PCS_PWD_ASYNC_MASK GENMASK(11, 10) > > +#define XTP_PCS_PWD_ASYNC(x) FIELD_PREP(XTP_PCS_PWD_ASYNC_MASK, (x)) > > +#define XTP_FRC_PCS_PWD_ASYNC BIT(8) > > +#define XTP_PCS_UPDT BIT(4) > > +#define XTP_PCS_IN_FR_RG BIT(0) > > + > > +#define REG_DIG_GLB_F4 0x00f4 > > +#define XFI_DPHY_PCS_SEL BIT(0) > > +#define XFI_DPHY_PCS_SEL_SGMII FIELD_PREP(XFI_DPHY_PCS_SEL, 1) > > +#define XFI_DPHY_PCS_SEL_USXGMII FIELD_PREP(XFI_DPHY_PCS_SEL, 0) > > +#define XFI_DPHY_AD_SGDT_FRC_EN BIT(5) > > + > > +#define REG_DIG_LN_TRX_40 0x3040 > > +#define XTP_LN_FRC_TX_DATA_EN BIT(29) > > +#define XTP_LN_TX_DATA_EN BIT(28) > > + > > +#define REG_DIG_LN_TRX_B0 0x30b0 > > +#define XTP_LN_FRC_TX_MACCK_EN BIT(5) > > +#define XTP_LN_TX_MACCK_EN BIT(4) > > + > > +#define REG_ANA_GLB_D0 0x90d0 > > +#define XTP_GLB_USXGMII_SEL_MASK GENMASK(3, 1) > > +#define XTP_GLB_USXGMII_SEL(x) FIELD_PREP(GENMASK(3, 1), (x)) > > +#define XTP_GLB_USXGMII_EN BIT(0) > > + > > +struct mtk_xfi_tphy { > > + void __iomem *base; > > + struct device *dev; > > + struct reset_control *reset; > > + struct clk_bulk_data clocks[MTK_XFI_TPHY_NUM_CLOCKS]; > > + bool da_war; > > +}; > > + > > +static void mtk_xfi_tphy_setup(struct mtk_xfi_tphy *xfi_tphy, > > + phy_interface_t interface) > > +{ > > + /* Override 10GBase-R tuning value if work-around is selected */ > > + bool da_war = (xfi_tphy->da_war && (interface == PHY_INTERFACE_MODE_10GBASER)); > > why do you need braces around this? Just for readability. They can safely be removed. > > > + /* Bools to make setting up values for specific PHY speeds easier */ > > + bool is_2p5g = (interface == PHY_INTERFACE_MODE_2500BASEX); > > + bool is_1g = (interface == PHY_INTERFACE_MODE_1000BASEX || > > + interface == PHY_INTERFACE_MODE_SGMII); > > + bool is_10g = (interface == PHY_INTERFACE_MODE_10GBASER || > > + interface == PHY_INTERFACE_MODE_USXGMII); > > + bool is_5g = (interface == PHY_INTERFACE_MODE_5GBASER); > > + /* Bool to configure input mux to either > > + * - USXGMII PCS (64b/66b coding) for 5G/10G > > + * - LynxI PCS (8b/10b coding) for 1G/2.5G > > + */ > > + bool use_lynxi_pcs = (is_1g || is_2p5g); > > This is quite terrible to read, how about declaring variables first and > then doing the initialization? Ack. > > > + > > + dev_dbg(xfi_tphy->dev, "setting up for mode %s\n", phy_modes(interface)); > > + > > + /* Setup PLL setting */ > > + mtk_phy_update_bits(xfi_tphy->base + 0x9024, 0x100000, is_10g ? 0x0 : 0x100000); > > + mtk_phy_update_bits(xfi_tphy->base + 0x2020, 0x202000, is_5g ? 0x202000 : 0x0); > > + mtk_phy_update_bits(xfi_tphy->base + 0x2030, 0x500, is_1g ? 0x0 : 0x500); > > + mtk_phy_update_bits(xfi_tphy->base + 0x2034, 0xa00, is_1g ? 0x0 : 0xa00); > > + mtk_phy_update_bits(xfi_tphy->base + 0x2040, 0x340000, is_1g ? 0x200000 : 0x140000); > > magic numbers? Yes, and not much we can do about them. According to MTK engineers (in Cc) they also don't know what those numbers really mean in detail and have only been given sequences of magic register writes for each interface mode ([1], [2], [3], [4], [5]) by the upstream IP supplier of the PHY. I then compared those write sequences with each others, and observed the behavior of each register (as in: read their value before and after the write operation; all of them read back the value written to them) and rewrote the initialization as one function only changing the bits actually needed (instead of always writing the complete 32-bit value). I've made sure that everything still works and Bc-bocun Chen of MediaTek (also in Cc) then helped to label at least some of the registers and bits there in as far as they are understood by MediaTek. [1]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/refs/heads/master/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_sgmii.c#172 [2]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/refs/heads/master/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_sgmii.c#284 [3]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/refs/heads/master/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_usxgmii.c#132 [4]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/refs/heads/master/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_usxgmii.c#246 [5]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/refs/heads/master/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_usxgmii.c#360 > > > + > > + /* Setup RXFE BW setting */ > > + mtk_phy_update_bits(xfi_tphy->base + 0x50f0, 0xc10, is_1g ? 0x410 : is_5g ? 0x800 : 0x400); > > + mtk_phy_update_bits(xfi_tphy->base + 0x50e0, 0x4000, is_5g ? 0x0 : 0x4000); > > + > > + /* Setup RX CDR setting */ > > + mtk_phy_update_bits(xfi_tphy->base + 0x506c, 0x30000, is_5g ? 0x0 : 0x30000); > > + mtk_phy_update_bits(xfi_tphy->base + 0x5070, 0x670000, is_5g ? 0x620000 : 0x50000); > > + mtk_phy_update_bits(xfi_tphy->base + 0x5074, 0x180000, is_5g ? 0x180000 : 0x0); > > + mtk_phy_update_bits(xfi_tphy->base + 0x5078, 0xf000400, is_5g ? 0x8000000 : > > + 0x7000400); > > + mtk_phy_update_bits(xfi_tphy->base + 0x507c, 0x5000500, is_5g ? 0x4000400 : > > + 0x1000100); > > + mtk_phy_update_bits(xfi_tphy->base + 0x5080, 0x1410, is_1g ? 0x400 : is_5g ? 0x1010 : 0x0); > > + mtk_phy_update_bits(xfi_tphy->base + 0x5084, 0x30300, is_1g ? 0x30300 : > > + is_5g ? 0x30100 : > > + 0x100); > > + mtk_phy_update_bits(xfi_tphy->base + 0x5088, 0x60200, is_1g ? 0x20200 : > > + is_5g ? 0x40000 : > > + 0x20000); > > + > > + /* Setting RXFE adaptation range setting */ > > + mtk_phy_update_bits(xfi_tphy->base + 0x50e4, 0xc0000, is_5g ? 0x0 : 0xc0000); > > + mtk_phy_update_bits(xfi_tphy->base + 0x50e8, 0x40000, is_5g ? 0x0 : 0x40000); > > + mtk_phy_update_bits(xfi_tphy->base + 0x50ec, 0xa00, is_1g ? 0x200 : 0x800); > > + mtk_phy_update_bits(xfi_tphy->base + 0x50a8, 0xee0000, is_5g ? 0x800000 : > > + 0x6e0000); > > + mtk_phy_update_bits(xfi_tphy->base + 0x6004, 0x190000, is_5g ? 0x0 : 0x190000); > > + > > + if (is_10g) > > + writel(0x01423342, xfi_tphy->base + 0x00f8); > > + else if (is_5g) > > + writel(0x00a132a1, xfi_tphy->base + 0x00f8); > > + else if (is_2p5g) > > + writel(0x009c329c, xfi_tphy->base + 0x00f8); > > + else > > + writel(0x00fa32fa, xfi_tphy->base + 0x00f8); > > + > > + /* Force SGDT_OUT off and select PCS */ > > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_F4, > > + XFI_DPHY_AD_SGDT_FRC_EN | XFI_DPHY_PCS_SEL, > > + XFI_DPHY_AD_SGDT_FRC_EN | > > + (use_lynxi_pcs ? XFI_DPHY_PCS_SEL_SGMII : > > + XFI_DPHY_PCS_SEL_USXGMII)); > > + > > + /* Force GLB_CKDET_OUT */ > > + mtk_phy_set_bits(xfi_tphy->base + 0x0030, 0xc00); > > + > > + /* Force AEQ on */ > > + writel(XTP_PCS_RX_EQ_IN_PROGRESS(2) | XTP_PCS_PWD_SYNC(2) | XTP_PCS_PWD_ASYNC(2), > > + xfi_tphy->base + REG_DIG_GLB_70); > > + > > + usleep_range(1, 5); > > + > > + /* Setup TX DA default value */ > > + mtk_phy_update_bits(xfi_tphy->base + 0x30b0, 0x30, 0x20); > > + writel(0x00008a01, xfi_tphy->base + 0x3028); > > + writel(0x0000a884, xfi_tphy->base + 0x302c); > > + writel(0x00083002, xfi_tphy->base + 0x3024); > > + > > + /* Setup RG default value */ > > + if (use_lynxi_pcs) { > > + writel(0x00011110, xfi_tphy->base + 0x3010); > > + writel(0x40704000, xfi_tphy->base + 0x3048); > > + } else { > > + writel(0x00022220, xfi_tphy->base + 0x3010); > > + writel(0x0f020a01, xfi_tphy->base + 0x5064); > > + writel(0x06100600, xfi_tphy->base + 0x50b4); > > + if (interface == PHY_INTERFACE_MODE_USXGMII) > > + writel(0x40704000, xfi_tphy->base + 0x3048); > > + else > > + writel(0x47684100, xfi_tphy->base + 0x3048); > > + } > > + > > + if (is_1g) > > + writel(0x0000c000, xfi_tphy->base + 0x3064); > > + > > + /* Setup RX EQ initial value */ > > + mtk_phy_update_bits(xfi_tphy->base + 0x3050, 0xa8000000, > > + (interface != PHY_INTERFACE_MODE_10GBASER) ? 0xa8000000 : 0x0); > > + mtk_phy_update_bits(xfi_tphy->base + 0x3054, 0xaa, > > + (interface != PHY_INTERFACE_MODE_10GBASER) ? 0xaa : 0x0); > > + > > + if (!use_lynxi_pcs) > > + writel(0x00000f00, xfi_tphy->base + 0x306c); > > + else if (is_2p5g) > > + writel(0x22000f00, xfi_tphy->base + 0x306c); > > + else > > + writel(0x20200f00, xfi_tphy->base + 0x306c); > > + > > + mtk_phy_update_bits(xfi_tphy->base + 0xa008, 0x10000, da_war ? 0x10000 : 0x0); > > + > > + mtk_phy_update_bits(xfi_tphy->base + 0xa060, 0x50000, use_lynxi_pcs ? 0x50000 : 0x40000); > > + > > + /* Setup PHYA speed */ > > + mtk_phy_update_bits(xfi_tphy->base + REG_ANA_GLB_D0, > > + XTP_GLB_USXGMII_SEL_MASK | XTP_GLB_USXGMII_EN, > > + is_10g ? XTP_GLB_USXGMII_SEL(0) : > > + is_5g ? XTP_GLB_USXGMII_SEL(1) : > > + is_2p5g ? XTP_GLB_USXGMII_SEL(2) : > > + XTP_GLB_USXGMII_SEL(3)); > > + mtk_phy_set_bits(xfi_tphy->base + REG_ANA_GLB_D0, XTP_GLB_USXGMII_EN); > > + > > + /* Release reset */ > > + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_GLB_70, > > + XTP_PCS_RST_B | XTP_FRC_PCS_RST_B); > > + usleep_range(150, 500); > > + > > + /* Switch to P0 */ > > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, > > + XTP_PCS_IN_FR_RG | > > + XTP_FRC_PCS_PWD_ASYNC | > > + XTP_PCS_PWD_ASYNC_MASK | > > + XTP_PCS_PWD_SYNC_MASK | > > + XTP_PCS_UPDT, > > + XTP_PCS_IN_FR_RG | > > + XTP_FRC_PCS_PWD_ASYNC | > > + XTP_PCS_UPDT); > > + usleep_range(1, 5); > > + > > + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_70, XTP_PCS_UPDT); > > + usleep_range(15, 50); > > + > > + if (use_lynxi_pcs) { > > + /* Switch to Gen2 */ > > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, > > + XTP_PCS_MODE_MASK | XTP_PCS_UPDT, > > + XTP_PCS_MODE(1) | XTP_PCS_UPDT); > > + } else { > > + /* Switch to Gen3 */ > > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, > > + XTP_PCS_MODE_MASK | XTP_PCS_UPDT, > > + XTP_PCS_MODE(2) | XTP_PCS_UPDT); > > + } > > + usleep_range(1, 5); > > + > > + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_70, XTP_PCS_UPDT); > > + > > + usleep_range(100, 500); > > + > > + /* Enable MAC CK */ > > + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_LN_TRX_B0, XTP_LN_TX_MACCK_EN); > > + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_F4, XFI_DPHY_AD_SGDT_FRC_EN); > > + > > + /* Enable TX data */ > > + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_LN_TRX_40, > > + XTP_LN_FRC_TX_DATA_EN | XTP_LN_TX_DATA_EN); > > + usleep_range(400, 1000); > > +} > > + > > +static int mtk_xfi_tphy_set_mode(struct phy *phy, enum phy_mode mode, int > > + submode) > > +{ > > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > > + > > + if (mode != PHY_MODE_ETHERNET) > > + return -EINVAL; > > + > > + switch (submode) { > > + case PHY_INTERFACE_MODE_1000BASEX: > > + case PHY_INTERFACE_MODE_2500BASEX: > > + case PHY_INTERFACE_MODE_SGMII: > > + case PHY_INTERFACE_MODE_5GBASER: > > + case PHY_INTERFACE_MODE_10GBASER: > > + case PHY_INTERFACE_MODE_USXGMII: > > + mtk_xfi_tphy_setup(xfi_tphy, submode); > > + return 0; > > + default: > > + return -EINVAL; > > + } > > +} > > + > > +static int mtk_xfi_tphy_reset(struct phy *phy) > > +{ > > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > > + > > + reset_control_assert(xfi_tphy->reset); > > + usleep_range(100, 500); > > + reset_control_deassert(xfi_tphy->reset); > > + usleep_range(1, 10); > > + > > + return 0; > > +} > > + > > +static int mtk_xfi_tphy_power_on(struct phy *phy) > > +{ > > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > > + > > + return clk_bulk_prepare_enable(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); > > +} > > + > > +static int mtk_xfi_tphy_power_off(struct phy *phy) > > +{ > > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > > + > > + clk_bulk_disable_unprepare(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); > > + > > + return 0; > > +} > > + > > +static const struct phy_ops mtk_xfi_tphy_ops = { > > + .power_on = mtk_xfi_tphy_power_on, > > + .power_off = mtk_xfi_tphy_power_off, > > + .set_mode = mtk_xfi_tphy_set_mode, > > + .reset = mtk_xfi_tphy_reset, > > + .owner = THIS_MODULE, > > +}; > > + > > +static int mtk_xfi_tphy_probe(struct platform_device *pdev) > > +{ > > + struct device_node *np = pdev->dev.of_node; > > + struct phy_provider *phy_provider; > > + struct mtk_xfi_tphy *xfi_tphy; > > + struct phy *phy; > > + int ret; > > + > > + if (!np) > > + return -ENODEV; > > + > > + xfi_tphy = devm_kzalloc(&pdev->dev, sizeof(*xfi_tphy), GFP_KERNEL); > > + if (!xfi_tphy) > > + return -ENOMEM; > > + > > + xfi_tphy->base = devm_platform_ioremap_resource(pdev, 0); > > + if (IS_ERR(xfi_tphy->base)) > > + return PTR_ERR(xfi_tphy->base); > > + > > + xfi_tphy->dev = &pdev->dev; > > + xfi_tphy->clocks[0].id = "topxtal"; > > + xfi_tphy->clocks[1].id = "xfipll"; > > + ret = devm_clk_bulk_get(&pdev->dev, MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); > > + if (ret) > > + return ret; > > + > > + xfi_tphy->reset = devm_reset_control_get_exclusive(&pdev->dev, NULL); > > + if (IS_ERR(xfi_tphy->reset)) > > + return PTR_ERR(xfi_tphy->reset); > > + > > + xfi_tphy->da_war = of_property_read_bool(np, "mediatek,usxgmii-performance-errata"); > > + > > + phy = devm_phy_create(&pdev->dev, NULL, &mtk_xfi_tphy_ops); > > + if (IS_ERR(phy)) > > + return PTR_ERR(phy); > > + > > + phy_set_drvdata(phy, xfi_tphy); > > + phy_provider = devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate); > > + > > + return PTR_ERR_OR_ZERO(phy_provider); > > +} > > + > > +static const struct of_device_id mtk_xfi_tphy_match[] = { > > + { .compatible = "mediatek,mt7988-xfi-tphy", }, > > + { /* sentinel */ } > > +}; > > +MODULE_DEVICE_TABLE(of, mtk_xfi_tphy_match); > > + > > +static struct platform_driver mtk_xfi_tphy_driver = { > > + .probe = mtk_xfi_tphy_probe, > > + .driver = { > > + .name = "mtk-xfi-tphy", > > + .of_match_table = mtk_xfi_tphy_match, > > + }, > > +}; > > +module_platform_driver(mtk_xfi_tphy_driver); > > + > > +MODULE_DESCRIPTION("MediaTek 10GE SerDes XFI T-PHY driver"); > > +MODULE_AUTHOR("Daniel Golle <daniel@makrotopia.org>"); > > +MODULE_AUTHOR("Bc-bocun Chen <bc-bocun.chen@mediatek.com>"); > > +MODULE_LICENSE("GPL"); > > -- > > 2.43.0 > > -- > ~Vinod
On 28-03-24, 20:12, Daniel Golle wrote: > Hi Vinod, > > thank you for taking your time to review my submission! > > On Fri, Mar 29, 2024 at 12:22:47AM +0530, Vinod Koul wrote: > > On 10-02-24, 02:10, Daniel Golle wrote: > > > Add driver for MediaTek's XFI T-PHY which can be found in the MT7988 > > > > What does XFI mean? > > https://en.wikipedia.org/wiki/XFP_transceiver#XFI > > I chose this name because names of functions dealing with the phy in > the vendor driver are prefixed "xfi_pextp_". > The register space used by the phy is called "pextp", which could be > read as "_P_CI _ex_press _T_-_P_hy", and that is quite misleading as > this phy isn't used for anything related to PCIe, so I wanted to find > a better name. > > XFI is still somehow related (as in: you would find the relevant > places using grep in the vendor driver when looking for that) and > seemed to at least somehow be aligned with the function of that phy: > Dealing with (up to) 10 Gbit/s Ethernet SerDes signals. > > MediaTek calls phys with more than one potential use T-PHY or X-PHY: > The capital letter 'T' graphically connects 3 points, two of them > being on the upper side representing the internal components and one > on the lower side representing the single external interface. > > Other vendors (like Marvell) call such things "combo phys". > > Anyway, if anyone has better ideas regarding the naming, now is the > moment to speak up ;) This is fine. Combo phys are more common for ones dealing with multiple components. I am fine either way. But it is good to document why this was named as such > > > > > > > SoC. The XFI T-PHY is a 10 Gigabit/s Ethernet SerDes PHY with muxes on > > > the internal side to be used with either USXGMII PCS or LynxI PCS, > > > depending on the selected PHY interface mode. > > > > > > The PHY can operates only in PHY_MODE_ETHERNET, the submode is one of > > > PHY_INTERFACE_MODE_* corresponding to the supported modes: > > > > > > * USXGMII \ > > > * 10GBase-R }- USXGMII PCS - XGDM \ > > > * 5GBase-R / \ > > > }- Ethernet MAC > > > * 2500Base-X \ / > > > * 1000Base-X }- LynxI PCS - GDM / > > > * Cisco SGMII (MAC side) / > > > > > > In order to work-around a performance issue present on the first of > > > two XFI T-PHYs present in MT7988, special tuning is applied which can be > > > selected by adding the 'mediatek,usxgmii-performance-errata' property to > > > the device tree node. > > > > > > There is no documentation for most registers used for the > > > analog/tuning part, however, most of the registers have been partially > > > reverse-engineered from MediaTek's SDK implementation (an opaque > > > sequence of 32-bit register writes) and descriptions for all relevant > > > digital registers and bits such as resets and muxes have been supplied > > > by MediaTek. > > > > > > Signed-off-by: Daniel Golle <daniel@makrotopia.org> > > > Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> > > > --- > > > v3: no changes > > > v2: > > > * use IO helpers from mtk-io.h instead of rolling my own > > > * use devm_clk_bulk_get() > > > * yse devm_platform_ioremap_resource() > > > * unify name and description everywhere > > > * invert bool is_xgmii into bool use_lynxi_pcs and add comments > > > describing the meaning of each of the stack variables > > > * not much we can do about remaining magic values unless MTK provides > > > definitions for them > > > > > > > > > MAINTAINERS | 1 + > > > drivers/phy/mediatek/Kconfig | 12 + > > > drivers/phy/mediatek/Makefile | 1 + > > > drivers/phy/mediatek/phy-mtk-xfi-tphy.c | 360 ++++++++++++++++++++++++ > > > 4 files changed, 374 insertions(+) > > > create mode 100644 drivers/phy/mediatek/phy-mtk-xfi-tphy.c > > > > > > diff --git a/MAINTAINERS b/MAINTAINERS > > > index 4be2fd097f261..616b86e3e62fd 100644 > > > --- a/MAINTAINERS > > > +++ b/MAINTAINERS > > > @@ -13776,6 +13776,7 @@ L: netdev@vger.kernel.org > > > S: Maintained > > > F: drivers/net/phy/mediatek-ge-soc.c > > > F: drivers/net/phy/mediatek-ge.c > > > +F: drivers/phy/mediatek/phy-mtk-xfi-tphy.c > > > > > > MEDIATEK I2C CONTROLLER DRIVER > > > M: Qii Wang <qii.wang@mediatek.com> > > > diff --git a/drivers/phy/mediatek/Kconfig b/drivers/phy/mediatek/Kconfig > > > index 3849b7c87d287..117d0e84c7360 100644 > > > --- a/drivers/phy/mediatek/Kconfig > > > +++ b/drivers/phy/mediatek/Kconfig > > > @@ -13,6 +13,18 @@ config PHY_MTK_PCIE > > > callback for PCIe GEN3 port, it supports software efuse > > > initialization. > > > > > > +config PHY_MTK_XFI_TPHY > > > + tristate "MediaTek 10GE SerDes XFI T-PHY driver" > > > + depends on ARCH_MEDIATEK || COMPILE_TEST > > > + depends on OF && OF_ADDRESS > > > > why both, is OF not enough? > > As we are already also depending on HAS_IOMEM what is left there is > basically just a !SPARC dependency. > And that is probably a historic left-over and (according to commit > 5ab5fc7e35705c from 2010...) should be re-evaluated. I'm happy to drop > OF_ADDRESS and keep only HAS_IOMEM, and we shall see if any of the > COMPILE_TESTs actually fails, given that everyone is fine with that. Yeah HAS_IOMEM would be required for it to get compiled on diff archs. I think OF should suffice... wdyt? > > > > > > + depends on HAS_IOMEM > > > + select GENERIC_PHY > > > + help > > > + Say 'Y' here to add support for MediaTek XFI T-PHY driver. > > > + The driver provides access to the Ethernet SerDes T-PHY supporting > > > + 1GE and 2.5GE modes via the LynxI PCS, and 5GE and 10GE modes > > > + via the USXGMII PCS found in MediaTek SoCs with 10G Ethernet. > > > + > > > config PHY_MTK_TPHY > > > tristate "MediaTek T-PHY Driver" > > > depends on ARCH_MEDIATEK || COMPILE_TEST > > > diff --git a/drivers/phy/mediatek/Makefile b/drivers/phy/mediatek/Makefile > > > index f6e24a47e0815..1b8088df71e84 100644 > > > --- a/drivers/phy/mediatek/Makefile > > > +++ b/drivers/phy/mediatek/Makefile > > > @@ -8,6 +8,7 @@ obj-$(CONFIG_PHY_MTK_PCIE) += phy-mtk-pcie.o > > > obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o > > > obj-$(CONFIG_PHY_MTK_UFS) += phy-mtk-ufs.o > > > obj-$(CONFIG_PHY_MTK_XSPHY) += phy-mtk-xsphy.o > > > +obj-$(CONFIG_PHY_MTK_XFI_TPHY) += phy-mtk-xfi-tphy.o > > > > > > phy-mtk-hdmi-drv-y := phy-mtk-hdmi.o > > > phy-mtk-hdmi-drv-y += phy-mtk-hdmi-mt2701.o > > > diff --git a/drivers/phy/mediatek/phy-mtk-xfi-tphy.c b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c > > > new file mode 100644 > > > index 0000000000000..551d6cee33f94 > > > --- /dev/null > > > +++ b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c > > > @@ -0,0 +1,360 @@ > > > +// SPDX-License-Identifier: GPL-2.0-or-later > > > +/* MediaTek 10GE SerDes XFI T-PHY driver > > > + * > > > + * Copyright (c) 2024 Daniel Golle <daniel@makrotopia.org> > > > + * Bc-bocun Chen <bc-bocun.chen@mediatek.com> > > > + * based on mtk_usxgmii.c and mtk_sgmii.c found in MediaTek's SDK (GPL-2.0) > > > + * Copyright (c) 2022 MediaTek Inc. > > > + * Author: Henry Yen <henry.yen@mediatek.com> > > > + */ > > > + > > > +#include <linux/module.h> > > > +#include <linux/device.h> > > > +#include <linux/platform_device.h> > > > +#include <linux/of.h> > > > +#include <linux/io.h> > > > +#include <linux/clk.h> > > > +#include <linux/reset.h> > > > +#include <linux/phy.h> > > > +#include <linux/phy/phy.h> > > > + > > > +#include "phy-mtk-io.h" > > > + > > > +#define MTK_XFI_TPHY_NUM_CLOCKS 2 > > > + > > > +#define REG_DIG_GLB_70 0x0070 > > > +#define XTP_PCS_RX_EQ_IN_PROGRESS(x) FIELD_PREP(GENMASK(25, 24), (x)) > > > +#define XTP_PCS_MODE_MASK GENMASK(17, 16) > > > +#define XTP_PCS_MODE(x) FIELD_PREP(GENMASK(17, 16), (x)) > > > +#define XTP_PCS_RST_B BIT(15) > > > +#define XTP_FRC_PCS_RST_B BIT(14) > > > +#define XTP_PCS_PWD_SYNC_MASK GENMASK(13, 12) > > > +#define XTP_PCS_PWD_SYNC(x) FIELD_PREP(XTP_PCS_PWD_SYNC_MASK, (x)) > > > +#define XTP_PCS_PWD_ASYNC_MASK GENMASK(11, 10) > > > +#define XTP_PCS_PWD_ASYNC(x) FIELD_PREP(XTP_PCS_PWD_ASYNC_MASK, (x)) > > > +#define XTP_FRC_PCS_PWD_ASYNC BIT(8) > > > +#define XTP_PCS_UPDT BIT(4) > > > +#define XTP_PCS_IN_FR_RG BIT(0) > > > + > > > +#define REG_DIG_GLB_F4 0x00f4 > > > +#define XFI_DPHY_PCS_SEL BIT(0) > > > +#define XFI_DPHY_PCS_SEL_SGMII FIELD_PREP(XFI_DPHY_PCS_SEL, 1) > > > +#define XFI_DPHY_PCS_SEL_USXGMII FIELD_PREP(XFI_DPHY_PCS_SEL, 0) > > > +#define XFI_DPHY_AD_SGDT_FRC_EN BIT(5) > > > + > > > +#define REG_DIG_LN_TRX_40 0x3040 > > > +#define XTP_LN_FRC_TX_DATA_EN BIT(29) > > > +#define XTP_LN_TX_DATA_EN BIT(28) > > > + > > > +#define REG_DIG_LN_TRX_B0 0x30b0 > > > +#define XTP_LN_FRC_TX_MACCK_EN BIT(5) > > > +#define XTP_LN_TX_MACCK_EN BIT(4) > > > + > > > +#define REG_ANA_GLB_D0 0x90d0 > > > +#define XTP_GLB_USXGMII_SEL_MASK GENMASK(3, 1) > > > +#define XTP_GLB_USXGMII_SEL(x) FIELD_PREP(GENMASK(3, 1), (x)) > > > +#define XTP_GLB_USXGMII_EN BIT(0) > > > + > > > +struct mtk_xfi_tphy { > > > + void __iomem *base; > > > + struct device *dev; > > > + struct reset_control *reset; > > > + struct clk_bulk_data clocks[MTK_XFI_TPHY_NUM_CLOCKS]; > > > + bool da_war; > > > +}; > > > + > > > +static void mtk_xfi_tphy_setup(struct mtk_xfi_tphy *xfi_tphy, > > > + phy_interface_t interface) > > > +{ > > > + /* Override 10GBase-R tuning value if work-around is selected */ > > > + bool da_war = (xfi_tphy->da_war && (interface == PHY_INTERFACE_MODE_10GBASER)); > > > > why do you need braces around this? > > Just for readability. They can safely be removed. > > > > > > + /* Bools to make setting up values for specific PHY speeds easier */ > > > + bool is_2p5g = (interface == PHY_INTERFACE_MODE_2500BASEX); > > > + bool is_1g = (interface == PHY_INTERFACE_MODE_1000BASEX || > > > + interface == PHY_INTERFACE_MODE_SGMII); > > > + bool is_10g = (interface == PHY_INTERFACE_MODE_10GBASER || > > > + interface == PHY_INTERFACE_MODE_USXGMII); > > > + bool is_5g = (interface == PHY_INTERFACE_MODE_5GBASER); > > > + /* Bool to configure input mux to either > > > + * - USXGMII PCS (64b/66b coding) for 5G/10G > > > + * - LynxI PCS (8b/10b coding) for 1G/2.5G > > > + */ > > > + bool use_lynxi_pcs = (is_1g || is_2p5g); > > > > This is quite terrible to read, how about declaring variables first and > > then doing the initialization? > > Ack. > > > > > > + > > > + dev_dbg(xfi_tphy->dev, "setting up for mode %s\n", phy_modes(interface)); > > > + > > > + /* Setup PLL setting */ > > > + mtk_phy_update_bits(xfi_tphy->base + 0x9024, 0x100000, is_10g ? 0x0 : 0x100000); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x2020, 0x202000, is_5g ? 0x202000 : 0x0); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x2030, 0x500, is_1g ? 0x0 : 0x500); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x2034, 0xa00, is_1g ? 0x0 : 0xa00); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x2040, 0x340000, is_1g ? 0x200000 : 0x140000); > > > > magic numbers? > > Yes, and not much we can do about them. According to MTK engineers (in > Cc) they also don't know what those numbers really mean in detail and > have only been given sequences of magic register writes for each > interface mode ([1], [2], [3], [4], [5]) by the upstream IP supplier > of the PHY. I then compared those write sequences with each others, > and observed the behavior of each register (as in: read their value > before and after the write operation; all of them read back the value > written to them) and rewrote the initialization as one function only > changing the bits actually needed (instead of always writing the complete > 32-bit value). I've made sure that everything still works and Bc-bocun > Chen of MediaTek (also in Cc) then helped to label at least some of > the registers and bits there in as far as they are understood by > MediaTek. > > [1]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/refs/heads/master/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_sgmii.c#172 > [2]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/refs/heads/master/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_sgmii.c#284 > [3]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/refs/heads/master/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_usxgmii.c#132 > [4]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/refs/heads/master/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_usxgmii.c#246 > [5]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/refs/heads/master/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_usxgmii.c#360 Okay lets document the source of magic values so that people may refer to these > > > > > > + > > > + /* Setup RXFE BW setting */ > > > + mtk_phy_update_bits(xfi_tphy->base + 0x50f0, 0xc10, is_1g ? 0x410 : is_5g ? 0x800 : 0x400); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x50e0, 0x4000, is_5g ? 0x0 : 0x4000); > > > + > > > + /* Setup RX CDR setting */ > > > + mtk_phy_update_bits(xfi_tphy->base + 0x506c, 0x30000, is_5g ? 0x0 : 0x30000); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x5070, 0x670000, is_5g ? 0x620000 : 0x50000); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x5074, 0x180000, is_5g ? 0x180000 : 0x0); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x5078, 0xf000400, is_5g ? 0x8000000 : > > > + 0x7000400); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x507c, 0x5000500, is_5g ? 0x4000400 : > > > + 0x1000100); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x5080, 0x1410, is_1g ? 0x400 : is_5g ? 0x1010 : 0x0); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x5084, 0x30300, is_1g ? 0x30300 : > > > + is_5g ? 0x30100 : > > > + 0x100); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x5088, 0x60200, is_1g ? 0x20200 : > > > + is_5g ? 0x40000 : > > > + 0x20000); > > > + > > > + /* Setting RXFE adaptation range setting */ > > > + mtk_phy_update_bits(xfi_tphy->base + 0x50e4, 0xc0000, is_5g ? 0x0 : 0xc0000); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x50e8, 0x40000, is_5g ? 0x0 : 0x40000); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x50ec, 0xa00, is_1g ? 0x200 : 0x800); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x50a8, 0xee0000, is_5g ? 0x800000 : > > > + 0x6e0000); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x6004, 0x190000, is_5g ? 0x0 : 0x190000); > > > + > > > + if (is_10g) > > > + writel(0x01423342, xfi_tphy->base + 0x00f8); > > > + else if (is_5g) > > > + writel(0x00a132a1, xfi_tphy->base + 0x00f8); > > > + else if (is_2p5g) > > > + writel(0x009c329c, xfi_tphy->base + 0x00f8); > > > + else > > > + writel(0x00fa32fa, xfi_tphy->base + 0x00f8); > > > + > > > + /* Force SGDT_OUT off and select PCS */ > > > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_F4, > > > + XFI_DPHY_AD_SGDT_FRC_EN | XFI_DPHY_PCS_SEL, > > > + XFI_DPHY_AD_SGDT_FRC_EN | > > > + (use_lynxi_pcs ? XFI_DPHY_PCS_SEL_SGMII : > > > + XFI_DPHY_PCS_SEL_USXGMII)); > > > + > > > + /* Force GLB_CKDET_OUT */ > > > + mtk_phy_set_bits(xfi_tphy->base + 0x0030, 0xc00); > > > + > > > + /* Force AEQ on */ > > > + writel(XTP_PCS_RX_EQ_IN_PROGRESS(2) | XTP_PCS_PWD_SYNC(2) | XTP_PCS_PWD_ASYNC(2), > > > + xfi_tphy->base + REG_DIG_GLB_70); > > > + > > > + usleep_range(1, 5); > > > + > > > + /* Setup TX DA default value */ > > > + mtk_phy_update_bits(xfi_tphy->base + 0x30b0, 0x30, 0x20); > > > + writel(0x00008a01, xfi_tphy->base + 0x3028); > > > + writel(0x0000a884, xfi_tphy->base + 0x302c); > > > + writel(0x00083002, xfi_tphy->base + 0x3024); > > > + > > > + /* Setup RG default value */ > > > + if (use_lynxi_pcs) { > > > + writel(0x00011110, xfi_tphy->base + 0x3010); > > > + writel(0x40704000, xfi_tphy->base + 0x3048); > > > + } else { > > > + writel(0x00022220, xfi_tphy->base + 0x3010); > > > + writel(0x0f020a01, xfi_tphy->base + 0x5064); > > > + writel(0x06100600, xfi_tphy->base + 0x50b4); > > > + if (interface == PHY_INTERFACE_MODE_USXGMII) > > > + writel(0x40704000, xfi_tphy->base + 0x3048); > > > + else > > > + writel(0x47684100, xfi_tphy->base + 0x3048); > > > + } > > > + > > > + if (is_1g) > > > + writel(0x0000c000, xfi_tphy->base + 0x3064); > > > + > > > + /* Setup RX EQ initial value */ > > > + mtk_phy_update_bits(xfi_tphy->base + 0x3050, 0xa8000000, > > > + (interface != PHY_INTERFACE_MODE_10GBASER) ? 0xa8000000 : 0x0); > > > + mtk_phy_update_bits(xfi_tphy->base + 0x3054, 0xaa, > > > + (interface != PHY_INTERFACE_MODE_10GBASER) ? 0xaa : 0x0); > > > + > > > + if (!use_lynxi_pcs) > > > + writel(0x00000f00, xfi_tphy->base + 0x306c); > > > + else if (is_2p5g) > > > + writel(0x22000f00, xfi_tphy->base + 0x306c); > > > + else > > > + writel(0x20200f00, xfi_tphy->base + 0x306c); > > > + > > > + mtk_phy_update_bits(xfi_tphy->base + 0xa008, 0x10000, da_war ? 0x10000 : 0x0); > > > + > > > + mtk_phy_update_bits(xfi_tphy->base + 0xa060, 0x50000, use_lynxi_pcs ? 0x50000 : 0x40000); > > > + > > > + /* Setup PHYA speed */ > > > + mtk_phy_update_bits(xfi_tphy->base + REG_ANA_GLB_D0, > > > + XTP_GLB_USXGMII_SEL_MASK | XTP_GLB_USXGMII_EN, > > > + is_10g ? XTP_GLB_USXGMII_SEL(0) : > > > + is_5g ? XTP_GLB_USXGMII_SEL(1) : > > > + is_2p5g ? XTP_GLB_USXGMII_SEL(2) : > > > + XTP_GLB_USXGMII_SEL(3)); > > > + mtk_phy_set_bits(xfi_tphy->base + REG_ANA_GLB_D0, XTP_GLB_USXGMII_EN); > > > + > > > + /* Release reset */ > > > + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_GLB_70, > > > + XTP_PCS_RST_B | XTP_FRC_PCS_RST_B); > > > + usleep_range(150, 500); > > > + > > > + /* Switch to P0 */ > > > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, > > > + XTP_PCS_IN_FR_RG | > > > + XTP_FRC_PCS_PWD_ASYNC | > > > + XTP_PCS_PWD_ASYNC_MASK | > > > + XTP_PCS_PWD_SYNC_MASK | > > > + XTP_PCS_UPDT, > > > + XTP_PCS_IN_FR_RG | > > > + XTP_FRC_PCS_PWD_ASYNC | > > > + XTP_PCS_UPDT); > > > + usleep_range(1, 5); > > > + > > > + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_70, XTP_PCS_UPDT); > > > + usleep_range(15, 50); > > > + > > > + if (use_lynxi_pcs) { > > > + /* Switch to Gen2 */ > > > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, > > > + XTP_PCS_MODE_MASK | XTP_PCS_UPDT, > > > + XTP_PCS_MODE(1) | XTP_PCS_UPDT); > > > + } else { > > > + /* Switch to Gen3 */ > > > + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, > > > + XTP_PCS_MODE_MASK | XTP_PCS_UPDT, > > > + XTP_PCS_MODE(2) | XTP_PCS_UPDT); > > > + } > > > + usleep_range(1, 5); > > > + > > > + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_70, XTP_PCS_UPDT); > > > + > > > + usleep_range(100, 500); > > > + > > > + /* Enable MAC CK */ > > > + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_LN_TRX_B0, XTP_LN_TX_MACCK_EN); > > > + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_F4, XFI_DPHY_AD_SGDT_FRC_EN); > > > + > > > + /* Enable TX data */ > > > + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_LN_TRX_40, > > > + XTP_LN_FRC_TX_DATA_EN | XTP_LN_TX_DATA_EN); > > > + usleep_range(400, 1000); > > > +} > > > + > > > +static int mtk_xfi_tphy_set_mode(struct phy *phy, enum phy_mode mode, int > > > + submode) > > > +{ > > > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > > > + > > > + if (mode != PHY_MODE_ETHERNET) > > > + return -EINVAL; > > > + > > > + switch (submode) { > > > + case PHY_INTERFACE_MODE_1000BASEX: > > > + case PHY_INTERFACE_MODE_2500BASEX: > > > + case PHY_INTERFACE_MODE_SGMII: > > > + case PHY_INTERFACE_MODE_5GBASER: > > > + case PHY_INTERFACE_MODE_10GBASER: > > > + case PHY_INTERFACE_MODE_USXGMII: > > > + mtk_xfi_tphy_setup(xfi_tphy, submode); > > > + return 0; > > > + default: > > > + return -EINVAL; > > > + } > > > +} > > > + > > > +static int mtk_xfi_tphy_reset(struct phy *phy) > > > +{ > > > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > > > + > > > + reset_control_assert(xfi_tphy->reset); > > > + usleep_range(100, 500); > > > + reset_control_deassert(xfi_tphy->reset); > > > + usleep_range(1, 10); > > > + > > > + return 0; > > > +} > > > + > > > +static int mtk_xfi_tphy_power_on(struct phy *phy) > > > +{ > > > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > > > + > > > + return clk_bulk_prepare_enable(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); > > > +} > > > + > > > +static int mtk_xfi_tphy_power_off(struct phy *phy) > > > +{ > > > + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); > > > + > > > + clk_bulk_disable_unprepare(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); > > > + > > > + return 0; > > > +} > > > + > > > +static const struct phy_ops mtk_xfi_tphy_ops = { > > > + .power_on = mtk_xfi_tphy_power_on, > > > + .power_off = mtk_xfi_tphy_power_off, > > > + .set_mode = mtk_xfi_tphy_set_mode, > > > + .reset = mtk_xfi_tphy_reset, > > > + .owner = THIS_MODULE, > > > +}; > > > + > > > +static int mtk_xfi_tphy_probe(struct platform_device *pdev) > > > +{ > > > + struct device_node *np = pdev->dev.of_node; > > > + struct phy_provider *phy_provider; > > > + struct mtk_xfi_tphy *xfi_tphy; > > > + struct phy *phy; > > > + int ret; > > > + > > > + if (!np) > > > + return -ENODEV; > > > + > > > + xfi_tphy = devm_kzalloc(&pdev->dev, sizeof(*xfi_tphy), GFP_KERNEL); > > > + if (!xfi_tphy) > > > + return -ENOMEM; > > > + > > > + xfi_tphy->base = devm_platform_ioremap_resource(pdev, 0); > > > + if (IS_ERR(xfi_tphy->base)) > > > + return PTR_ERR(xfi_tphy->base); > > > + > > > + xfi_tphy->dev = &pdev->dev; > > > + xfi_tphy->clocks[0].id = "topxtal"; > > > + xfi_tphy->clocks[1].id = "xfipll"; > > > + ret = devm_clk_bulk_get(&pdev->dev, MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); > > > + if (ret) > > > + return ret; > > > + > > > + xfi_tphy->reset = devm_reset_control_get_exclusive(&pdev->dev, NULL); > > > + if (IS_ERR(xfi_tphy->reset)) > > > + return PTR_ERR(xfi_tphy->reset); > > > + > > > + xfi_tphy->da_war = of_property_read_bool(np, "mediatek,usxgmii-performance-errata"); > > > + > > > + phy = devm_phy_create(&pdev->dev, NULL, &mtk_xfi_tphy_ops); > > > + if (IS_ERR(phy)) > > > + return PTR_ERR(phy); > > > + > > > + phy_set_drvdata(phy, xfi_tphy); > > > + phy_provider = devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate); > > > + > > > + return PTR_ERR_OR_ZERO(phy_provider); > > > +} > > > + > > > +static const struct of_device_id mtk_xfi_tphy_match[] = { > > > + { .compatible = "mediatek,mt7988-xfi-tphy", }, > > > + { /* sentinel */ } > > > +}; > > > +MODULE_DEVICE_TABLE(of, mtk_xfi_tphy_match); > > > + > > > +static struct platform_driver mtk_xfi_tphy_driver = { > > > + .probe = mtk_xfi_tphy_probe, > > > + .driver = { > > > + .name = "mtk-xfi-tphy", > > > + .of_match_table = mtk_xfi_tphy_match, > > > + }, > > > +}; > > > +module_platform_driver(mtk_xfi_tphy_driver); > > > + > > > +MODULE_DESCRIPTION("MediaTek 10GE SerDes XFI T-PHY driver"); > > > +MODULE_AUTHOR("Daniel Golle <daniel@makrotopia.org>"); > > > +MODULE_AUTHOR("Bc-bocun Chen <bc-bocun.chen@mediatek.com>"); > > > +MODULE_LICENSE("GPL"); > > > -- > > > 2.43.0 > > > > -- > > ~Vinod
diff --git a/MAINTAINERS b/MAINTAINERS index 4be2fd097f261..616b86e3e62fd 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -13776,6 +13776,7 @@ L: netdev@vger.kernel.org S: Maintained F: drivers/net/phy/mediatek-ge-soc.c F: drivers/net/phy/mediatek-ge.c +F: drivers/phy/mediatek/phy-mtk-xfi-tphy.c MEDIATEK I2C CONTROLLER DRIVER M: Qii Wang <qii.wang@mediatek.com> diff --git a/drivers/phy/mediatek/Kconfig b/drivers/phy/mediatek/Kconfig index 3849b7c87d287..117d0e84c7360 100644 --- a/drivers/phy/mediatek/Kconfig +++ b/drivers/phy/mediatek/Kconfig @@ -13,6 +13,18 @@ config PHY_MTK_PCIE callback for PCIe GEN3 port, it supports software efuse initialization. +config PHY_MTK_XFI_TPHY + tristate "MediaTek 10GE SerDes XFI T-PHY driver" + depends on ARCH_MEDIATEK || COMPILE_TEST + depends on OF && OF_ADDRESS + depends on HAS_IOMEM + select GENERIC_PHY + help + Say 'Y' here to add support for MediaTek XFI T-PHY driver. + The driver provides access to the Ethernet SerDes T-PHY supporting + 1GE and 2.5GE modes via the LynxI PCS, and 5GE and 10GE modes + via the USXGMII PCS found in MediaTek SoCs with 10G Ethernet. + config PHY_MTK_TPHY tristate "MediaTek T-PHY Driver" depends on ARCH_MEDIATEK || COMPILE_TEST diff --git a/drivers/phy/mediatek/Makefile b/drivers/phy/mediatek/Makefile index f6e24a47e0815..1b8088df71e84 100644 --- a/drivers/phy/mediatek/Makefile +++ b/drivers/phy/mediatek/Makefile @@ -8,6 +8,7 @@ obj-$(CONFIG_PHY_MTK_PCIE) += phy-mtk-pcie.o obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o obj-$(CONFIG_PHY_MTK_UFS) += phy-mtk-ufs.o obj-$(CONFIG_PHY_MTK_XSPHY) += phy-mtk-xsphy.o +obj-$(CONFIG_PHY_MTK_XFI_TPHY) += phy-mtk-xfi-tphy.o phy-mtk-hdmi-drv-y := phy-mtk-hdmi.o phy-mtk-hdmi-drv-y += phy-mtk-hdmi-mt2701.o diff --git a/drivers/phy/mediatek/phy-mtk-xfi-tphy.c b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c new file mode 100644 index 0000000000000..551d6cee33f94 --- /dev/null +++ b/drivers/phy/mediatek/phy-mtk-xfi-tphy.c @@ -0,0 +1,360 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* MediaTek 10GE SerDes XFI T-PHY driver + * + * Copyright (c) 2024 Daniel Golle <daniel@makrotopia.org> + * Bc-bocun Chen <bc-bocun.chen@mediatek.com> + * based on mtk_usxgmii.c and mtk_sgmii.c found in MediaTek's SDK (GPL-2.0) + * Copyright (c) 2022 MediaTek Inc. + * Author: Henry Yen <henry.yen@mediatek.com> + */ + +#include <linux/module.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/io.h> +#include <linux/clk.h> +#include <linux/reset.h> +#include <linux/phy.h> +#include <linux/phy/phy.h> + +#include "phy-mtk-io.h" + +#define MTK_XFI_TPHY_NUM_CLOCKS 2 + +#define REG_DIG_GLB_70 0x0070 +#define XTP_PCS_RX_EQ_IN_PROGRESS(x) FIELD_PREP(GENMASK(25, 24), (x)) +#define XTP_PCS_MODE_MASK GENMASK(17, 16) +#define XTP_PCS_MODE(x) FIELD_PREP(GENMASK(17, 16), (x)) +#define XTP_PCS_RST_B BIT(15) +#define XTP_FRC_PCS_RST_B BIT(14) +#define XTP_PCS_PWD_SYNC_MASK GENMASK(13, 12) +#define XTP_PCS_PWD_SYNC(x) FIELD_PREP(XTP_PCS_PWD_SYNC_MASK, (x)) +#define XTP_PCS_PWD_ASYNC_MASK GENMASK(11, 10) +#define XTP_PCS_PWD_ASYNC(x) FIELD_PREP(XTP_PCS_PWD_ASYNC_MASK, (x)) +#define XTP_FRC_PCS_PWD_ASYNC BIT(8) +#define XTP_PCS_UPDT BIT(4) +#define XTP_PCS_IN_FR_RG BIT(0) + +#define REG_DIG_GLB_F4 0x00f4 +#define XFI_DPHY_PCS_SEL BIT(0) +#define XFI_DPHY_PCS_SEL_SGMII FIELD_PREP(XFI_DPHY_PCS_SEL, 1) +#define XFI_DPHY_PCS_SEL_USXGMII FIELD_PREP(XFI_DPHY_PCS_SEL, 0) +#define XFI_DPHY_AD_SGDT_FRC_EN BIT(5) + +#define REG_DIG_LN_TRX_40 0x3040 +#define XTP_LN_FRC_TX_DATA_EN BIT(29) +#define XTP_LN_TX_DATA_EN BIT(28) + +#define REG_DIG_LN_TRX_B0 0x30b0 +#define XTP_LN_FRC_TX_MACCK_EN BIT(5) +#define XTP_LN_TX_MACCK_EN BIT(4) + +#define REG_ANA_GLB_D0 0x90d0 +#define XTP_GLB_USXGMII_SEL_MASK GENMASK(3, 1) +#define XTP_GLB_USXGMII_SEL(x) FIELD_PREP(GENMASK(3, 1), (x)) +#define XTP_GLB_USXGMII_EN BIT(0) + +struct mtk_xfi_tphy { + void __iomem *base; + struct device *dev; + struct reset_control *reset; + struct clk_bulk_data clocks[MTK_XFI_TPHY_NUM_CLOCKS]; + bool da_war; +}; + +static void mtk_xfi_tphy_setup(struct mtk_xfi_tphy *xfi_tphy, + phy_interface_t interface) +{ + /* Override 10GBase-R tuning value if work-around is selected */ + bool da_war = (xfi_tphy->da_war && (interface == PHY_INTERFACE_MODE_10GBASER)); + /* Bools to make setting up values for specific PHY speeds easier */ + bool is_2p5g = (interface == PHY_INTERFACE_MODE_2500BASEX); + bool is_1g = (interface == PHY_INTERFACE_MODE_1000BASEX || + interface == PHY_INTERFACE_MODE_SGMII); + bool is_10g = (interface == PHY_INTERFACE_MODE_10GBASER || + interface == PHY_INTERFACE_MODE_USXGMII); + bool is_5g = (interface == PHY_INTERFACE_MODE_5GBASER); + /* Bool to configure input mux to either + * - USXGMII PCS (64b/66b coding) for 5G/10G + * - LynxI PCS (8b/10b coding) for 1G/2.5G + */ + bool use_lynxi_pcs = (is_1g || is_2p5g); + + dev_dbg(xfi_tphy->dev, "setting up for mode %s\n", phy_modes(interface)); + + /* Setup PLL setting */ + mtk_phy_update_bits(xfi_tphy->base + 0x9024, 0x100000, is_10g ? 0x0 : 0x100000); + mtk_phy_update_bits(xfi_tphy->base + 0x2020, 0x202000, is_5g ? 0x202000 : 0x0); + mtk_phy_update_bits(xfi_tphy->base + 0x2030, 0x500, is_1g ? 0x0 : 0x500); + mtk_phy_update_bits(xfi_tphy->base + 0x2034, 0xa00, is_1g ? 0x0 : 0xa00); + mtk_phy_update_bits(xfi_tphy->base + 0x2040, 0x340000, is_1g ? 0x200000 : 0x140000); + + /* Setup RXFE BW setting */ + mtk_phy_update_bits(xfi_tphy->base + 0x50f0, 0xc10, is_1g ? 0x410 : is_5g ? 0x800 : 0x400); + mtk_phy_update_bits(xfi_tphy->base + 0x50e0, 0x4000, is_5g ? 0x0 : 0x4000); + + /* Setup RX CDR setting */ + mtk_phy_update_bits(xfi_tphy->base + 0x506c, 0x30000, is_5g ? 0x0 : 0x30000); + mtk_phy_update_bits(xfi_tphy->base + 0x5070, 0x670000, is_5g ? 0x620000 : 0x50000); + mtk_phy_update_bits(xfi_tphy->base + 0x5074, 0x180000, is_5g ? 0x180000 : 0x0); + mtk_phy_update_bits(xfi_tphy->base + 0x5078, 0xf000400, is_5g ? 0x8000000 : + 0x7000400); + mtk_phy_update_bits(xfi_tphy->base + 0x507c, 0x5000500, is_5g ? 0x4000400 : + 0x1000100); + mtk_phy_update_bits(xfi_tphy->base + 0x5080, 0x1410, is_1g ? 0x400 : is_5g ? 0x1010 : 0x0); + mtk_phy_update_bits(xfi_tphy->base + 0x5084, 0x30300, is_1g ? 0x30300 : + is_5g ? 0x30100 : + 0x100); + mtk_phy_update_bits(xfi_tphy->base + 0x5088, 0x60200, is_1g ? 0x20200 : + is_5g ? 0x40000 : + 0x20000); + + /* Setting RXFE adaptation range setting */ + mtk_phy_update_bits(xfi_tphy->base + 0x50e4, 0xc0000, is_5g ? 0x0 : 0xc0000); + mtk_phy_update_bits(xfi_tphy->base + 0x50e8, 0x40000, is_5g ? 0x0 : 0x40000); + mtk_phy_update_bits(xfi_tphy->base + 0x50ec, 0xa00, is_1g ? 0x200 : 0x800); + mtk_phy_update_bits(xfi_tphy->base + 0x50a8, 0xee0000, is_5g ? 0x800000 : + 0x6e0000); + mtk_phy_update_bits(xfi_tphy->base + 0x6004, 0x190000, is_5g ? 0x0 : 0x190000); + + if (is_10g) + writel(0x01423342, xfi_tphy->base + 0x00f8); + else if (is_5g) + writel(0x00a132a1, xfi_tphy->base + 0x00f8); + else if (is_2p5g) + writel(0x009c329c, xfi_tphy->base + 0x00f8); + else + writel(0x00fa32fa, xfi_tphy->base + 0x00f8); + + /* Force SGDT_OUT off and select PCS */ + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_F4, + XFI_DPHY_AD_SGDT_FRC_EN | XFI_DPHY_PCS_SEL, + XFI_DPHY_AD_SGDT_FRC_EN | + (use_lynxi_pcs ? XFI_DPHY_PCS_SEL_SGMII : + XFI_DPHY_PCS_SEL_USXGMII)); + + /* Force GLB_CKDET_OUT */ + mtk_phy_set_bits(xfi_tphy->base + 0x0030, 0xc00); + + /* Force AEQ on */ + writel(XTP_PCS_RX_EQ_IN_PROGRESS(2) | XTP_PCS_PWD_SYNC(2) | XTP_PCS_PWD_ASYNC(2), + xfi_tphy->base + REG_DIG_GLB_70); + + usleep_range(1, 5); + + /* Setup TX DA default value */ + mtk_phy_update_bits(xfi_tphy->base + 0x30b0, 0x30, 0x20); + writel(0x00008a01, xfi_tphy->base + 0x3028); + writel(0x0000a884, xfi_tphy->base + 0x302c); + writel(0x00083002, xfi_tphy->base + 0x3024); + + /* Setup RG default value */ + if (use_lynxi_pcs) { + writel(0x00011110, xfi_tphy->base + 0x3010); + writel(0x40704000, xfi_tphy->base + 0x3048); + } else { + writel(0x00022220, xfi_tphy->base + 0x3010); + writel(0x0f020a01, xfi_tphy->base + 0x5064); + writel(0x06100600, xfi_tphy->base + 0x50b4); + if (interface == PHY_INTERFACE_MODE_USXGMII) + writel(0x40704000, xfi_tphy->base + 0x3048); + else + writel(0x47684100, xfi_tphy->base + 0x3048); + } + + if (is_1g) + writel(0x0000c000, xfi_tphy->base + 0x3064); + + /* Setup RX EQ initial value */ + mtk_phy_update_bits(xfi_tphy->base + 0x3050, 0xa8000000, + (interface != PHY_INTERFACE_MODE_10GBASER) ? 0xa8000000 : 0x0); + mtk_phy_update_bits(xfi_tphy->base + 0x3054, 0xaa, + (interface != PHY_INTERFACE_MODE_10GBASER) ? 0xaa : 0x0); + + if (!use_lynxi_pcs) + writel(0x00000f00, xfi_tphy->base + 0x306c); + else if (is_2p5g) + writel(0x22000f00, xfi_tphy->base + 0x306c); + else + writel(0x20200f00, xfi_tphy->base + 0x306c); + + mtk_phy_update_bits(xfi_tphy->base + 0xa008, 0x10000, da_war ? 0x10000 : 0x0); + + mtk_phy_update_bits(xfi_tphy->base + 0xa060, 0x50000, use_lynxi_pcs ? 0x50000 : 0x40000); + + /* Setup PHYA speed */ + mtk_phy_update_bits(xfi_tphy->base + REG_ANA_GLB_D0, + XTP_GLB_USXGMII_SEL_MASK | XTP_GLB_USXGMII_EN, + is_10g ? XTP_GLB_USXGMII_SEL(0) : + is_5g ? XTP_GLB_USXGMII_SEL(1) : + is_2p5g ? XTP_GLB_USXGMII_SEL(2) : + XTP_GLB_USXGMII_SEL(3)); + mtk_phy_set_bits(xfi_tphy->base + REG_ANA_GLB_D0, XTP_GLB_USXGMII_EN); + + /* Release reset */ + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_GLB_70, + XTP_PCS_RST_B | XTP_FRC_PCS_RST_B); + usleep_range(150, 500); + + /* Switch to P0 */ + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, + XTP_PCS_IN_FR_RG | + XTP_FRC_PCS_PWD_ASYNC | + XTP_PCS_PWD_ASYNC_MASK | + XTP_PCS_PWD_SYNC_MASK | + XTP_PCS_UPDT, + XTP_PCS_IN_FR_RG | + XTP_FRC_PCS_PWD_ASYNC | + XTP_PCS_UPDT); + usleep_range(1, 5); + + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_70, XTP_PCS_UPDT); + usleep_range(15, 50); + + if (use_lynxi_pcs) { + /* Switch to Gen2 */ + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, + XTP_PCS_MODE_MASK | XTP_PCS_UPDT, + XTP_PCS_MODE(1) | XTP_PCS_UPDT); + } else { + /* Switch to Gen3 */ + mtk_phy_update_bits(xfi_tphy->base + REG_DIG_GLB_70, + XTP_PCS_MODE_MASK | XTP_PCS_UPDT, + XTP_PCS_MODE(2) | XTP_PCS_UPDT); + } + usleep_range(1, 5); + + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_70, XTP_PCS_UPDT); + + usleep_range(100, 500); + + /* Enable MAC CK */ + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_LN_TRX_B0, XTP_LN_TX_MACCK_EN); + mtk_phy_clear_bits(xfi_tphy->base + REG_DIG_GLB_F4, XFI_DPHY_AD_SGDT_FRC_EN); + + /* Enable TX data */ + mtk_phy_set_bits(xfi_tphy->base + REG_DIG_LN_TRX_40, + XTP_LN_FRC_TX_DATA_EN | XTP_LN_TX_DATA_EN); + usleep_range(400, 1000); +} + +static int mtk_xfi_tphy_set_mode(struct phy *phy, enum phy_mode mode, int + submode) +{ + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); + + if (mode != PHY_MODE_ETHERNET) + return -EINVAL; + + switch (submode) { + case PHY_INTERFACE_MODE_1000BASEX: + case PHY_INTERFACE_MODE_2500BASEX: + case PHY_INTERFACE_MODE_SGMII: + case PHY_INTERFACE_MODE_5GBASER: + case PHY_INTERFACE_MODE_10GBASER: + case PHY_INTERFACE_MODE_USXGMII: + mtk_xfi_tphy_setup(xfi_tphy, submode); + return 0; + default: + return -EINVAL; + } +} + +static int mtk_xfi_tphy_reset(struct phy *phy) +{ + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); + + reset_control_assert(xfi_tphy->reset); + usleep_range(100, 500); + reset_control_deassert(xfi_tphy->reset); + usleep_range(1, 10); + + return 0; +} + +static int mtk_xfi_tphy_power_on(struct phy *phy) +{ + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); + + return clk_bulk_prepare_enable(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); +} + +static int mtk_xfi_tphy_power_off(struct phy *phy) +{ + struct mtk_xfi_tphy *xfi_tphy = phy_get_drvdata(phy); + + clk_bulk_disable_unprepare(MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); + + return 0; +} + +static const struct phy_ops mtk_xfi_tphy_ops = { + .power_on = mtk_xfi_tphy_power_on, + .power_off = mtk_xfi_tphy_power_off, + .set_mode = mtk_xfi_tphy_set_mode, + .reset = mtk_xfi_tphy_reset, + .owner = THIS_MODULE, +}; + +static int mtk_xfi_tphy_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct phy_provider *phy_provider; + struct mtk_xfi_tphy *xfi_tphy; + struct phy *phy; + int ret; + + if (!np) + return -ENODEV; + + xfi_tphy = devm_kzalloc(&pdev->dev, sizeof(*xfi_tphy), GFP_KERNEL); + if (!xfi_tphy) + return -ENOMEM; + + xfi_tphy->base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(xfi_tphy->base)) + return PTR_ERR(xfi_tphy->base); + + xfi_tphy->dev = &pdev->dev; + xfi_tphy->clocks[0].id = "topxtal"; + xfi_tphy->clocks[1].id = "xfipll"; + ret = devm_clk_bulk_get(&pdev->dev, MTK_XFI_TPHY_NUM_CLOCKS, xfi_tphy->clocks); + if (ret) + return ret; + + xfi_tphy->reset = devm_reset_control_get_exclusive(&pdev->dev, NULL); + if (IS_ERR(xfi_tphy->reset)) + return PTR_ERR(xfi_tphy->reset); + + xfi_tphy->da_war = of_property_read_bool(np, "mediatek,usxgmii-performance-errata"); + + phy = devm_phy_create(&pdev->dev, NULL, &mtk_xfi_tphy_ops); + if (IS_ERR(phy)) + return PTR_ERR(phy); + + phy_set_drvdata(phy, xfi_tphy); + phy_provider = devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate); + + return PTR_ERR_OR_ZERO(phy_provider); +} + +static const struct of_device_id mtk_xfi_tphy_match[] = { + { .compatible = "mediatek,mt7988-xfi-tphy", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, mtk_xfi_tphy_match); + +static struct platform_driver mtk_xfi_tphy_driver = { + .probe = mtk_xfi_tphy_probe, + .driver = { + .name = "mtk-xfi-tphy", + .of_match_table = mtk_xfi_tphy_match, + }, +}; +module_platform_driver(mtk_xfi_tphy_driver); + +MODULE_DESCRIPTION("MediaTek 10GE SerDes XFI T-PHY driver"); +MODULE_AUTHOR("Daniel Golle <daniel@makrotopia.org>"); +MODULE_AUTHOR("Bc-bocun Chen <bc-bocun.chen@mediatek.com>"); +MODULE_LICENSE("GPL");
Add driver for MediaTek's XFI T-PHY which can be found in the MT7988 SoC. The XFI T-PHY is a 10 Gigabit/s Ethernet SerDes PHY with muxes on the internal side to be used with either USXGMII PCS or LynxI PCS, depending on the selected PHY interface mode. The PHY can operates only in PHY_MODE_ETHERNET, the submode is one of PHY_INTERFACE_MODE_* corresponding to the supported modes: * USXGMII \ * 10GBase-R }- USXGMII PCS - XGDM \ * 5GBase-R / \ }- Ethernet MAC * 2500Base-X \ / * 1000Base-X }- LynxI PCS - GDM / * Cisco SGMII (MAC side) / In order to work-around a performance issue present on the first of two XFI T-PHYs present in MT7988, special tuning is applied which can be selected by adding the 'mediatek,usxgmii-performance-errata' property to the device tree node. There is no documentation for most registers used for the analog/tuning part, however, most of the registers have been partially reverse-engineered from MediaTek's SDK implementation (an opaque sequence of 32-bit register writes) and descriptions for all relevant digital registers and bits such as resets and muxes have been supplied by MediaTek. Signed-off-by: Daniel Golle <daniel@makrotopia.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> --- v3: no changes v2: * use IO helpers from mtk-io.h instead of rolling my own * use devm_clk_bulk_get() * yse devm_platform_ioremap_resource() * unify name and description everywhere * invert bool is_xgmii into bool use_lynxi_pcs and add comments describing the meaning of each of the stack variables * not much we can do about remaining magic values unless MTK provides definitions for them MAINTAINERS | 1 + drivers/phy/mediatek/Kconfig | 12 + drivers/phy/mediatek/Makefile | 1 + drivers/phy/mediatek/phy-mtk-xfi-tphy.c | 360 ++++++++++++++++++++++++ 4 files changed, 374 insertions(+) create mode 100644 drivers/phy/mediatek/phy-mtk-xfi-tphy.c