@@ -4,6 +4,8 @@ menuconfig NET_DSA_MICROCHIP_KSZ_COMMON
depends on NET_DSA
select NET_DSA_TAG_KSZ
select NET_DSA_TAG_NONE
+ select NET_IEEE8021Q_HELPERS
+ select DCB
help
This driver adds support for Microchip KSZ9477 series switch and
KSZ8795/KSZ88x3 switch chips.
@@ -1,6 +1,6 @@
# SPDX-License-Identifier: GPL-2.0-only
obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ_COMMON) += ksz_switch.o
-ksz_switch-objs := ksz_common.o
+ksz_switch-objs := ksz_common.o ksz_dcb.o
ksz_switch-objs += ksz9477.o ksz9477_acl.o ksz9477_tc_flower.o
ksz_switch-objs += ksz8795.o
ksz_switch-objs += lan937x_main.o
@@ -28,6 +28,7 @@
#include <net/switchdev.h>
#include "ksz_common.h"
+#include "ksz_dcb.h"
#include "ksz_ptp.h"
#include "ksz8.h"
#include "ksz9477.h"
@@ -2371,6 +2372,10 @@ static int ksz_setup(struct dsa_switch *ds)
goto out_ptp_clock_unregister;
}
+ ret = ksz_dcb_init(dev);
+ if (ret)
+ goto out_ptp_clock_unregister;
+
/* start switch */
regmap_update_bits(ksz_regmap_8(dev), regs[S_START_CTRL],
SW_START, SW_START);
@@ -2698,7 +2703,7 @@ static int ksz_port_setup(struct dsa_switch *ds, int port)
* there is no need to do anything.
*/
- return 0;
+ return ksz_dcb_init_port(dev, port);
}
void ksz_port_stp_state_set(struct dsa_switch *ds, int port, u8 state)
@@ -3950,6 +3955,11 @@ static const struct dsa_switch_ops ksz_switch_ops = {
.port_setup_tc = ksz_setup_tc,
.get_mac_eee = ksz_get_mac_eee,
.set_mac_eee = ksz_set_mac_eee,
+ .port_get_default_prio = ksz_port_get_default_prio,
+ .port_set_default_prio = ksz_port_set_default_prio,
+ .port_get_dscp_prio = ksz_port_get_dscp_prio,
+ .port_set_apptrust = ksz_port_set_apptrust,
+ .port_get_apptrust = ksz_port_get_apptrust,
};
struct ksz_device *ksz_switch_alloc(struct device *base, void *priv)
@@ -621,6 +621,11 @@ static inline bool ksz_is_ksz88x3(struct ksz_device *dev)
return dev->chip_id == KSZ8830_CHIP_ID;
}
+static inline bool is_ksz8(struct ksz_device *dev)
+{
+ return ksz_is_ksz87xx(dev) || ksz_is_ksz88x3(dev);
+}
+
static inline int is_lan937x(struct ksz_device *dev)
{
return dev->chip_id == LAN9370_CHIP_ID ||
new file mode 100644
@@ -0,0 +1,548 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2024 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
+
+#include <linux/dsa/ksz_common.h>
+#include <net/dsa.h>
+#include <net/dscp.h>
+#include <net/ieee8021q.h>
+
+#include "ksz_common.h"
+#include "ksz_dcb.h"
+#include "ksz8.h"
+
+#define KSZ8_REG_PORT_1_CTRL_0 0x10
+#define KSZ8_PORT_DIFFSERV_ENABLE BIT(6)
+#define KSZ8_PORT_802_1P_ENABLE BIT(5)
+#define KSZ8_PORT_BASED_PRIO_M GENMASK(4, 3)
+
+#define KSZ88X3_REG_TOS_DSCP_CTRL 0x60
+#define KSZ8765_REG_TOS_DSCP_CTRL 0x90
+
+#define KSZ9477_REG_SW_MAC_TOS_CTRL 0x033e
+#define KSZ9477_SW_TOS_DSCP_REMAP BIT(0)
+#define KSZ9477_SW_TOS_DSCP_DEFAULT_PRIO_M GENMASK(5, 3)
+
+#define KSZ9477_REG_DIFFSERV_PRIO_MAP 0x0340
+
+#define KSZ9477_REG_PORT_MRI_PRIO_CTRL 0x0801
+#define KSZ9477_PORT_HIGHEST_PRIO BIT(7)
+#define KSZ9477_PORT_OR_PRIO BIT(6)
+#define KSZ9477_PORT_MAC_PRIO_ENABLE BIT(4)
+#define KSZ9477_PORT_VLAN_PRIO_ENABLE BIT(3)
+#define KSZ9477_PORT_802_1P_PRIO_ENABLE BIT(2)
+#define KSZ9477_PORT_DIFFSERV_PRIO_ENABLE BIT(1)
+#define KSZ9477_PORT_ACL_PRIO_ENABLE BIT(0)
+
+#define KSZ9477_REG_PORT_MRI_MAC_CTRL 0x0802
+#define KSZ9477_PORT_BASED_PRIO_M GENMASK(2, 0)
+
+struct ksz_apptrust_map {
+ u8 apptrust;
+ u8 bit;
+};
+
+static const struct ksz_apptrust_map ksz8_apptrust_map_to_bit[] = {
+ { DCB_APP_SEL_PCP, KSZ8_PORT_802_1P_ENABLE },
+ { IEEE_8021QAZ_APP_SEL_DSCP, KSZ8_PORT_DIFFSERV_ENABLE },
+};
+
+static const struct ksz_apptrust_map ksz9477_apptrust_map_to_bit[] = {
+ { DCB_APP_SEL_PCP, KSZ9477_PORT_802_1P_PRIO_ENABLE },
+ { IEEE_8021QAZ_APP_SEL_DSCP, KSZ9477_PORT_DIFFSERV_PRIO_ENABLE },
+};
+
+/*
+ * ksz_supported_apptrust[] - Supported apptrust selectors and Priority Order
+ * of Internal Priority Value (IPV) sources.
+ *
+ * This array defines the apptrust selectors supported by the hardware, where
+ * the index within the array indicates the priority of the selector - lower
+ * indices correspond to higher priority. This fixed priority scheme is due to
+ * the hardware's design, which does not support configurable priority among
+ * different priority sources.
+ *
+ * The priority sources, including Tail Tag, ACL, VLAN PCP and DSCP are ordered
+ * by the hardware's fixed logic, as detailed below. The order reflects a
+ * non-configurable precedence where certain types of priority information
+ * override others:
+ *
+ * 1. Tail Tag - Highest priority, overrides ACL, VLAN PCP, and DSCP priorities.
+ * 2. ACL - Overrides VLAN PCP and DSCP priorities.
+ * 3. VLAN PCP - Overrides DSCP priority.
+ * 4. DSCP - Lowest priority, does not override any other priority source.
+ *
+ * In this context, the array's lower index (higher priority) for
+ * 'DCB_APP_SEL_PCP' suggests its relative priority over
+ * 'IEEE_8021QAZ_APP_SEL_DSCP' within the system's fixed priority scheme.
+ *
+ * DCB_APP_SEL_PCP - Priority Code Point selector
+ * IEEE_8021QAZ_APP_SEL_DSCP - Differentiated Services Code Point selector
+ */
+static const u8 ksz_supported_apptrust[] = {
+ DCB_APP_SEL_PCP,
+ IEEE_8021QAZ_APP_SEL_DSCP,
+};
+
+static const u8 ksz8_port2_supported_apptrust[] = {
+ DCB_APP_SEL_PCP,
+};
+
+static const char * const ksz_supported_apptrust_variants[] = {
+ "empty", "dscp", "pcp", "dscp pcp"
+};
+
+static void ksz_get_defult_port_prio_reg(struct ksz_device *dev, int *reg,
+ u8 *mask, int *shift)
+{
+ if (is_ksz8(dev)) {
+ *reg = KSZ8_REG_PORT_1_CTRL_0;
+ *mask = KSZ8_PORT_BASED_PRIO_M;
+ *shift = __bf_shf(KSZ8_PORT_BASED_PRIO_M);
+ } else {
+ *reg = KSZ9477_REG_PORT_MRI_MAC_CTRL;
+ *mask = KSZ9477_PORT_BASED_PRIO_M;
+ *shift = __bf_shf(KSZ9477_PORT_BASED_PRIO_M);
+ }
+}
+
+/**
+ * ksz_port_get_default_prio - Retrieves the default priority for a port on a
+ * KSZ switch
+ * @ds: Pointer to the DSA switch structure
+ * @port: Port number from which to get the default priority
+ *
+ * This function fetches the default priority for the specified port on a KSZ
+ * switch.
+ *
+ * Return: The default priority of the port on success, or a negative error
+ * code on failure.
+ */
+int ksz_port_get_default_prio(struct dsa_switch *ds, int port)
+{
+ struct ksz_device *dev = ds->priv;
+ int ret, reg, shift;
+ u8 data, mask;
+
+ ksz_get_defult_port_prio_reg(dev, ®, &mask, &shift);
+
+ ret = ksz_pread8(dev, port, reg, &data);
+ if (ret)
+ return ret;
+
+ return (data & mask) >> shift;
+}
+
+/**
+ * ksz_port_set_default_prio - Sets the default priority for a port on a KSZ
+ * switch
+ * @ds: Pointer to the DSA switch structure
+ * @port: Port number for which to set the default priority
+ * @prio: Priority value to set
+ *
+ * This function sets the default priority for the specified port on a KSZ
+ * switch.
+ *
+ * Return: 0 on success, or a negative error code on failure.
+ */
+int ksz_port_set_default_prio(struct dsa_switch *ds, int port, u8 prio)
+{
+ struct ksz_device *dev = ds->priv;
+ int reg, shift;
+ u8 mask;
+
+ if (prio >= dev->info->num_tx_queues)
+ return -EINVAL;
+
+ ksz_get_defult_port_prio_reg(dev, ®, &mask, &shift);
+
+ return ksz_prmw8(dev, port, reg, mask, (prio << shift) & mask);
+}
+
+/**
+ * ksz_get_dscp_prio_reg - Retrieves the DSCP-to-priority-mapping register
+ * @dev: Pointer to the KSZ switch device structure
+ * @reg: Pointer to the register address to be set
+ * @per_reg: Pointer to the number of DSCP values per register
+ * @mask: Pointer to the mask to be set
+ *
+ * This function retrieves the DSCP to priority mapping register, the number of
+ * DSCP values per register, and the mask to be set.
+ */
+static void ksz_get_dscp_prio_reg(struct ksz_device *dev, int *reg,
+ int *per_reg, u8 *mask)
+{
+ if (ksz_is_ksz87xx(dev)) {
+ *reg = KSZ8765_REG_TOS_DSCP_CTRL;
+ *per_reg = 4;
+ *mask = GENMASK(1, 0);
+ } else if (ksz_is_ksz88x3(dev)) {
+ *reg = KSZ88X3_REG_TOS_DSCP_CTRL;
+ *per_reg = 4;
+ *mask = GENMASK(1, 0);
+ } else {
+ *reg = KSZ9477_REG_DIFFSERV_PRIO_MAP;
+ *per_reg = 2;
+ *mask = GENMASK(2, 0);
+ }
+}
+
+/**
+ * ksz_port_get_dscp_prio - Retrieves the priority for a DSCP value on a KSZ
+ * switch
+ * @ds: Pointer to the DSA switch structure
+ * @port: Port number for which to get the priority
+ * @dscp: DSCP value for which to get the priority
+ *
+ * This function fetches the priority value from switch global DSCP-to-priorty
+ * mapping table for the specified DSCP value.
+ *
+ * Return: The priority value for the DSCP on success, or a negative error
+ * code on failure.
+ */
+int ksz_port_get_dscp_prio(struct dsa_switch *ds, int port, u8 dscp)
+{
+ struct ksz_device *dev = ds->priv;
+ int reg, per_reg, ret, shift;
+ u8 data, mask;
+
+ ksz_get_dscp_prio_reg(dev, ®, &per_reg, &mask);
+
+ /* If DSCP remapping is disabled, DSCP bits 3-5 are used as Internal
+ * Priority Value (IPV)
+ */
+ if (!is_ksz8(dev)) {
+ ret = ksz_read8(dev, KSZ9477_REG_SW_MAC_TOS_CTRL, &data);
+ if (ret)
+ return ret;
+
+ /* If DSCP remapping is disabled, DSCP bits 3-5 are used as
+ * Internal Priority Value (IPV)
+ */
+ if (!(data & KSZ9477_SW_TOS_DSCP_REMAP))
+ return FIELD_GET(KSZ9477_SW_TOS_DSCP_DEFAULT_PRIO_M,
+ dscp);
+ }
+
+ /* In case DSCP remapping is enabled, we need to write the DSCP to
+ * priority mapping table.
+ */
+ reg += dscp / per_reg;
+ ret = ksz_read8(dev, reg, &data);
+ if (ret)
+ return ret;
+
+ shift = (dscp % per_reg) * (8 / per_reg);
+
+ return (data >> shift) & mask;
+}
+
+/**
+ * ksz_init_global_dscp_map - Initializes the global DSCP-to-priority mapping
+ * @dev: Pointer to the KSZ switch device structure
+ *
+ * This function initializes the global DSCP-to-priority mapping table for the
+ * switch.
+ *
+ * Return: 0 on success, or a negative error code on failure
+ */
+static int ksz_init_global_dscp_map(struct ksz_device *dev)
+{
+ int reg, per_reg, ret, dscp;
+ u8 data = 0;
+ u8 mask;
+
+ /* On KSZ9xxx variants, DSCP remapping is disabled by default.
+ * Enable to have, predictable and reproducible behavior across
+ * different devices.
+ */
+ if (!is_ksz8(dev)) {
+ ret = ksz_rmw8(dev, KSZ9477_REG_SW_MAC_TOS_CTRL,
+ KSZ9477_SW_TOS_DSCP_REMAP,
+ KSZ9477_SW_TOS_DSCP_REMAP);
+ if (ret)
+ return ret;
+ }
+
+ ksz_get_dscp_prio_reg(dev, ®, &per_reg, &mask);
+
+ for (dscp = 0; dscp < DSCP_MAX; dscp++) {
+ int ipv, shift, tt;
+
+ /* Map DSCP to Traffic Type, which is corresponding to the
+ * Internal Priority Value (IPV) in the switch.
+ */
+ if (!is_ksz8(dev)) {
+ ipv = ietf_dscp_to_ieee8021q_tt(dscp);
+ } else {
+ /* On KSZ8xxx variants we do not have IPV to queue
+ * remapping table. We need to convert DSCP to Traffic
+ * Type and then to queue.
+ */
+ tt = ietf_dscp_to_ieee8021q_tt(dscp);
+ if (tt < 0)
+ return tt;
+
+ ipv = ieee8021q_tt_to_tc(tt, dev->info->num_tx_queues);
+ }
+
+ if (ipv < 0)
+ return ipv;
+
+ shift = (dscp % per_reg) * (8 / per_reg);
+ data |= (ipv & mask) << shift;
+
+ if (dscp % per_reg == per_reg - 1) {
+ ret = ksz_write8(dev, reg + (dscp / per_reg), data);
+ if (ret)
+ return ret;
+
+ data = 0;
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * ksz_apptrust_error - Prints an error message for an invalid apptrust selector
+ * @dev: Pointer to the KSZ switch device structure
+ *
+ * This function prints an error message when an invalid apptrust selector is
+ * provided.
+ */
+static void ksz_apptrust_error(struct ksz_device *dev)
+{
+ char supported_apptrust_variants[64];
+ int i;
+
+ supported_apptrust_variants[0] = '\0';
+ for (i = 0; i < ARRAY_SIZE(ksz_supported_apptrust_variants); i++) {
+ if (i > 0)
+ strlcat(supported_apptrust_variants, ", ",
+ sizeof(supported_apptrust_variants));
+ strlcat(supported_apptrust_variants,
+ ksz_supported_apptrust_variants[i],
+ sizeof(supported_apptrust_variants));
+ }
+
+ dev_err(dev->dev, "Invalid apptrust selector or priority order. Supported: %s\n",
+ supported_apptrust_variants);
+}
+
+/**
+ * ksz_port_set_apptrust_validate - Validates the apptrust selectors
+ * @dev: Pointer to the KSZ switch device structure
+ * @port: Port number for which to set the apptrust selectors
+ * @sel: Array of apptrust selectors to validate
+ * @nsel: Number of apptrust selectors in the array
+ *
+ * This function validates the apptrust selectors provided and ensures that
+ * they are in the correct order.
+ *
+ * This family of switches supports two apptrust selectors: DCB_APP_SEL_PCP and
+ * IEEE_8021QAZ_APP_SEL_DSCP. The priority order of the selectors is fixed and
+ * cannot be changed. The order is as follows:
+ * 1. DCB_APP_SEL_PCP - Priority Code Point selector (highest priority)
+ * 2. IEEE_8021QAZ_APP_SEL_DSCP - Differentiated Services Code Point selector
+ * (lowest priority)
+ *
+ * Return: 0 on success, or a negative error code on failure
+ */
+static int ksz_port_set_apptrust_validate(struct ksz_device *dev, int port,
+ const u8 *sel, int nsel)
+{
+ int i, j, found;
+ int j_prev = 0;
+
+ /* Iterate through the requested selectors */
+ for (i = 0; i < nsel; i++) {
+ found = 0;
+
+ /* Check if the current selector is supported by the hardware */
+ for (j = 0; j < sizeof(ksz_supported_apptrust); j++) {
+ if (sel[i] != ksz_supported_apptrust[j])
+ continue;
+
+ found = 1;
+
+ /* Ensure that no higher priority selector (lower index)
+ * precedes a lower priority one
+ */
+ if (i > 0 && j <= j_prev)
+ goto invalid;
+
+ j_prev = j;
+ break;
+ }
+
+ if (!found)
+ goto invalid;
+ }
+
+ return 0;
+
+invalid:
+ ksz_apptrust_error(dev);
+
+ return -EINVAL;
+}
+
+/**
+ * ksz_get_apptrus_map_and_reg - Retrieves the apptrust map and register
+ * @dev: Pointer to the KSZ switch device structure
+ * @map: Pointer to the apptrust map to be set
+ * @reg: Pointer to the register address to be set
+ * @mask: Pointer to the mask to be set
+ *
+ * This function retrieves the apptrust map and register address for the
+ * apptrust configuration.
+ */
+static void ksz_get_apptrus_map_and_reg(struct ksz_device *dev,
+ const struct ksz_apptrust_map **map,
+ int *reg, u8 *mask)
+{
+ if (is_ksz8(dev)) {
+ *map = ksz8_apptrust_map_to_bit;
+ *reg = KSZ8_REG_PORT_1_CTRL_0;
+ *mask = KSZ8_PORT_DIFFSERV_ENABLE | KSZ8_PORT_802_1P_ENABLE;
+ } else {
+ *map = ksz9477_apptrust_map_to_bit;
+ *reg = KSZ9477_REG_PORT_MRI_PRIO_CTRL;
+ *mask = KSZ9477_PORT_802_1P_PRIO_ENABLE |
+ KSZ9477_PORT_DIFFSERV_PRIO_ENABLE;
+ }
+}
+
+/**
+ * ksz_port_set_apptrust - Sets the apptrust selectors for a port on a KSZ
+ * switch
+ * @ds: Pointer to the DSA switch structure
+ * @port: Port number for which to set the apptrust selectors
+ * @sel: Array of apptrust selectors to set
+ * @nsel: Number of apptrust selectors in the array
+ *
+ * This function sets the apptrust selectors for the specified port on a KSZ
+ * switch.
+ *
+ * Return: 0 on success, or a negative error code on failure
+ */
+int ksz_port_set_apptrust(struct dsa_switch *ds, int port,
+ const u8 *sel, int nsel)
+{
+ const struct ksz_apptrust_map *map;
+ struct ksz_device *dev = ds->priv;
+ int reg, i, ret;
+ u8 data = 0;
+ u8 mask;
+
+ ret = ksz_port_set_apptrust_validate(dev, port, sel, nsel);
+ if (ret)
+ return ret;
+
+ ksz_get_apptrus_map_and_reg(dev, &map, ®, &mask);
+
+ for (i = 0; i < nsel; i++) {
+ int j;
+
+ for (j = 0; j < ARRAY_SIZE(ksz_supported_apptrust); j++) {
+ if (sel[i] != ksz_supported_apptrust[j])
+ continue;
+
+ data |= map[j].bit;
+ break;
+ }
+ }
+
+ return ksz_prmw8(dev, port, reg, mask, data);
+}
+
+/**
+ * ksz_port_get_apptrust - Retrieves the apptrust selectors for a port on a KSZ
+ * switch
+ * @ds: Pointer to the DSA switch structure
+ * @port: Port number for which to get the apptrust selectors
+ * @sel: Array to store the apptrust selectors
+ * @nsel: Number of apptrust selectors in the array
+ *
+ * This function fetches the apptrust selectors for the specified port on a KSZ
+ * switch.
+ *
+ * Return: 0 on success, or a negative error code on failure
+ */
+int ksz_port_get_apptrust(struct dsa_switch *ds, int port, u8 *sel, int *nsel)
+{
+ const struct ksz_apptrust_map *map;
+ struct ksz_device *dev = ds->priv;
+ int reg, i, ret;
+ u8 data;
+ u8 mask;
+
+ ksz_get_apptrus_map_and_reg(dev, &map, ®, &mask);
+
+ ret = ksz_pread8(dev, port, reg, &data);
+ if (ret)
+ return ret;
+
+ *nsel = 0;
+ for (i = 0; i < ARRAY_SIZE(ksz_supported_apptrust); i++) {
+ if (data & map[i].bit)
+ sel[(*nsel)++] = ksz_supported_apptrust[i];
+ }
+
+ return 0;
+}
+
+/**
+ * ksz_dcb_init_port - Initializes the DCB configuration for a port on a KSZ
+ * @dev: Pointer to the KSZ switch device structure
+ * @port: Port number for which to initialize the DCB configuration
+ *
+ * This function initializes the DCB configuration for the specified port on a
+ * KSZ switch. Particular DCB configuration is set for the port, including the
+ * default priority and apptrust selectors.
+ * The default priority is set to Best Effort, and the apptrust selectors are
+ * set to all supported selectors.
+ *
+ * Return: 0 on success, or a negative error code on failure
+ */
+int ksz_dcb_init_port(struct ksz_device *dev, int port)
+{
+ int ret, ipv;
+
+ if (is_ksz8(dev)) {
+ ipv = ieee8021q_tt_to_tc(IEEE8021Q_TT_BE,
+ dev->info->num_tx_queues);
+ if (ipv < 0)
+ return ipv;
+ } else {
+ ipv = IEEE8021Q_TT_BE;
+ }
+
+ /* Set the default priority for the port to Best Effort */
+ ret = ksz_port_set_default_prio(dev->ds, port, ipv);
+ if (ret)
+ return ret;
+
+ return ksz_port_set_apptrust(dev->ds, port, ksz_supported_apptrust,
+ ARRAY_SIZE(ksz_supported_apptrust));
+}
+
+/**
+ * ksz_dcb_init - Initializes the DCB configuration for a KSZ switch
+ * @dev: Pointer to the KSZ switch device structure
+ *
+ * This function initializes the DCB configuration for a KSZ switch. The global
+ * DSCP-to-priority mapping table is initialized.
+ *
+ * Return: 0 on success, or a negative error code on failure
+ */
+int ksz_dcb_init(struct ksz_device *dev)
+{
+ int ret;
+
+ ret = ksz_init_global_dscp_map(dev);
+ if (ret)
+ return ret;
+
+ return 0;
+}
new file mode 100644
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (c) 2024 Pengutronix, Oleksij Rempel <kernel@pengutronix.de> */
+
+#ifndef __KSZ_DCB_H
+#define __KSZ_DCB_H
+
+#include <net/dsa.h>
+
+#include "ksz_common.h"
+
+int ksz_port_get_default_prio(struct dsa_switch *ds, int port);
+int ksz_port_set_default_prio(struct dsa_switch *ds, int port, u8 prio);
+int ksz_port_get_dscp_prio(struct dsa_switch *ds, int port, u8 dscp);
+int ksz_port_set_apptrust(struct dsa_switch *ds, int port,
+ const unsigned char *sel,
+ int nsel);
+int ksz_port_get_apptrust(struct dsa_switch *ds, int port, u8 *sel, int *nsel);
+int ksz_dcb_init_port(struct ksz_device *dev, int port);
+int ksz_dcb_init(struct ksz_device *dev);
+
+#endif /* __KSZ_DCB_H */
Add DCB support to configure app trust sources and default port priority. Following commands can be used for testing: dcb apptrust set dev lan1 order pcp dscp dcb app replace dev lan1 default-prio 3 Since it is not possible to configure DSCP-Prio mapping per port, this patch provide only ability to read switch global dscp-prio mapping and way to enable/disable app trust for DSCP. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- drivers/net/dsa/microchip/Kconfig | 2 + drivers/net/dsa/microchip/Makefile | 2 +- drivers/net/dsa/microchip/ksz_common.c | 12 +- drivers/net/dsa/microchip/ksz_common.h | 5 + drivers/net/dsa/microchip/ksz_dcb.c | 548 +++++++++++++++++++++++++ drivers/net/dsa/microchip/ksz_dcb.h | 21 + 6 files changed, 588 insertions(+), 2 deletions(-) create mode 100644 drivers/net/dsa/microchip/ksz_dcb.c create mode 100644 drivers/net/dsa/microchip/ksz_dcb.h